clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller

The Meson8/Meson8b/Meson8m2 SoCs embed a DDR clock controller in the
MMCBUS registers. There is no public documentation, but the u

clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller

The Meson8/Meson8b/Meson8m2 SoCs embed a DDR clock controller in the
MMCBUS registers. There is no public documentation, but the u-boot GPL
sources from the Amlogic BSP show that the DDR clock controller is
identical on all three SoCs:
#define CFG_DDR_CLK 792
#define CFG_PLL_M (((CFG_DDR_CLK/12)*12)/24)
#define CFG_PLL_N 1
#define CFG_PLL_OD 1

// from set_ddr_clock:
t_ddr_pll_cntl= (CFG_PLL_OD << 16)|(CFG_PLL_N<<9)|(CFG_PLL_M<<0)
writel(timing_reg->t_ddr_pll_cntl|(1<<29),AM_DDR_PLL_CNTL);
writel(readl(AM_DDR_PLL_CNTL) & (~(1<<29)),AM_DDR_PLL_CNTL);

// from hx_ddr_power_down_enter: shut down DDR PLL
writel(readl(AM_DDR_PLL_CNTL)|(1<<30),AM_DDR_PLL_CNTL);

do { ... } while((readl(AM_DDR_PLL_CNTL)&(1<<31))==0)

This translates to:
- AM_DDR_PLL_CNTL[29] is the reset bit
- AM_DDR_PLL_CNTL[30] is the enable bit
- AM_DDR_PLL_CNTL[31] is the lock bit
- AM_DDR_PLL_CNTL[8:0] is the m value (assuming the width is 9 bits
based on the start of the n value)
- AM_DDR_PLL_CNTL[13:9] is the n value (assuming the width is 5 bits
based on the start of the od)
- AM_DDR_PLL_CNTL[17:16] is the od (assuming the width is 2 bits based
on other PLLs on this SoC)

Add a driver for this PLL setup because it's used as one of the inputs
of the audio clocks. There may be more clocks inside that clock
controller - those can be added in subsequent patches.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

show more ...

clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller

The Meson8/Meson8b/Meson8m2 SoCs embed a DDR clock controller in the
MMCBUS registers. There is no public documentatio

clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller

The Meson8/Meson8b/Meson8m2 SoCs embed a DDR clock controller in the
MMCBUS registers. There is no public documentation, but the u-boot GPL
sources from the Amlogic BSP show that the DDR clock controller is
identical on all three SoCs:
#define CFG_DDR_CLK 792
#define CFG_PLL_M (((CFG_DDR_CLK/12)*12)/24)
#define CFG_PLL_N 1
#define CFG_PLL_OD 1

// from set_ddr_clock:
t_ddr_pll_cntl= (CFG_PLL_OD << 16)|(CFG_PLL_N<<9)|(CFG_PLL_M<<0)
writel(timing_reg->t_ddr_pll_cntl|(1<<29),AM_DDR_PLL_CNTL);
writel(readl(AM_DDR_PLL_CNTL) & (~(1<<29)),AM_DDR_PLL_CNTL);

// from hx_ddr_power_down_enter: shut down DDR PLL
writel(readl(AM_DDR_PLL_CNTL)|(1<<30),AM_DDR_PLL_CNTL);

do { ... } while((readl(AM_DDR_PLL_CNTL)&(1<<31))==0)

This translates to:
- AM_DDR_PLL_CNTL[29] is the reset bit
- AM_DDR_PLL_CNTL[30] is the enable bit
- AM_DDR_PLL_CNTL[31] is the lock bit
- AM_DDR_PLL_CNTL[8:0] is the m value (assuming the width is 9 bits
based on the start of the n value)
- AM_DDR_PLL_CNTL[13:9] is the n value (assuming the width is 5 bits
based on the start of the od)
- AM_DDR_PLL_CNTL[17:16] is the od (assuming the width is 2 bits based
on other PLLs on this SoC)

Add a driver for this PLL setup because it's used as one of the inputs
of the audio clocks. There may be more clocks inside that clock
controller - those can be added in subsequent patches.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

show more ...