ACPI: fan: Bail out if extract package failed

Bail out if we extract the _FIF package failed, or we will end
of referencing the garbage information in fields[], the fan control
will be in mess, fix

ACPI: fan: Bail out if extract package failed

Bail out if we extract the _FIF package failed, or we will end
of referencing the garbage information in fields[], the fan control
will be in mess, fix it.

Fiexes: d445571fa369 ("ACPI: fan: Optimize struct acpi_fan_fif")
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

ACPI: fan: Reorder symbols to get rid of a few forward declarations

Having the driver struct at the end of the file isn't only more usual, it
also allows to drop a few forward declarations which are

ACPI: fan: Reorder symbols to get rid of a few forward declarations

Having the driver struct at the end of the file isn't only more usual, it
also allows to drop a few forward declarations which are just useless
repetition.

While at it also move the MODULE_... macros to the end of the file.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

ACPI: fan: Add additional attributes for fine grain control

Add additional attributes, which helps in implementing algorithm in
the user space to optimize fan control. These attributes are presented

ACPI: fan: Add additional attributes for fine grain control

Add additional attributes, which helps in implementing algorithm in
the user space to optimize fan control. These attributes are presented
in the same directory as the existing performance state attributes.

Additional attributes:

1. Support of fine grain control
Publish support of presence of fine grain control so that fan speed
can be tuned correctly. This attribute is called "fine_grain_control".

2. fan speed
Publish the actual fan rpm in sysfs. Knowing fan rpm is helpful to
reduce noise level and use passive control instead. Also fan performance
may not be same over time, so the same control value may not be enough
to run the fan at a speed. So a feedback value of speed is helpful. This
sysfs attribute is called "fan_speed_rpm".

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

ACPI: fan: Properly handle fine grain control

When _FIF object specifies support for fine grain control, then fan speed
can be set from 0 to 100% with the recommended minimum "step size" via
_FSL ob

ACPI: fan: Properly handle fine grain control

When _FIF object specifies support for fine grain control, then fan speed
can be set from 0 to 100% with the recommended minimum "step size" via
_FSL object. Here the control value doesn't need to match any value from
_FPS object.

Currently we have a simple solution implemented which just pick maximum
control value from _FPS to display the actual state, but this is not
optimal when there is a big window between two control values in
_FPS. Also there is no way to set to any speed which doesn't match
control values in _FPS. The system firmware can start the fan at speed
which doesn't match any control value.

To support fine grain control (when supported) via thermal sysfs:
- cooling device max state is not _FPS state count but it will be
100 / _FIF.step_size
Step size can be from 1 to 9.
- cooling device current state is _FST.control / _FIF.step_size
- cooling device set state will set the control value
cdev.curr_state * _FIF.step_size plus any adjustment for 100%.
By the spec, when control value do not sum to 100% because of
_FIF.step_size, OSPM may select an appropriate ending Level increment
to reach 100%.

There is no rounding during calculation. For example if step size
is 6:
thermal sysfs cooling device max_state = 100/6 = 16
So user can set any value from 0-16.

If the system boots with a _FST.control which is not multiples
of step_size, the thermal sysfs cur_state will be based on the
range. For example for step size = 6:
_FST.control thermal sysfs cur_state
------------------------------------------------
0-5 0
6-11 1
..
..
90-95 15
96-100 16

While setting the _FST.control, the compensation will be at
the last step for cur_state = 16, which will set the _FST.control
to 100.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

ACPI: fan: Optimize struct acpi_fan_fif

We don't need u64 to store the information about _FIF. There are two
booleans (fine_grain_ctrl and low_speed_notification) and one field
step_size which can t

ACPI: fan: Optimize struct acpi_fan_fif

We don't need u64 to store the information about _FIF. There are two
booleans (fine_grain_ctrl and low_speed_notification) and one field
step_size which can take value from 1-9. There are no internal users
of revision field. So convert all fields to u8, by not directly
extracting the _FIF info the struct. Use an intermediate buffer to
extract and assign.

This will help to do u32 math using these fields. No functional
changes are expected.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

ACPI: fan: Separate file for attributes creation

Move the functionality of creation of sysfs attributes under acpi device
to a new file fan_attr.c. This cleans up the core fan code, which just
use t

ACPI: fan: Separate file for attributes creation

Move the functionality of creation of sysfs attributes under acpi device
to a new file fan_attr.c. This cleans up the core fan code, which just
use thermal sysfs interface. The original fan.c is renamed to
fan_core.c.

No functional changes are expected.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...