KVM: PPC: Fetch prefixed instructions from the guest

In order to handle emulation of prefixed instructions in the guest,
this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64
bits on 64

KVM: PPC: Fetch prefixed instructions from the guest

In order to handle emulation of prefixed instructions in the guest,
this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64
bits on 64-bit platforms. For prefixed instructions, the upper 32
bits are used for the prefix and the lower 32 bits for the suffix, and
both halves are byte-swapped if the guest endianness differs from the
host.

Next, vcpu->arch.emul_inst is now 64 bits wide, to match the HEIR
register on POWER10. Like HEIR, for a prefixed instruction it is
defined to have the prefix is in the top 32 bits and the suffix in the
bottom 32 bits, with both halves in the correct byte order.

kvmppc_get_last_inst is extended on 64-bit machines to put the prefix
and suffix in the right places in the ppc_inst_t being returned.

kvmppc_load_last_inst now returns the instruction in an unsigned long
in the same format as vcpu->arch.last_inst. It makes the decision
about whether to fetch a suffix based on the SRR1_PREFIXED bit in the
MSR image stored in the vcpu struct, which generally comes from SRR1
or HSRR1 on an interrupt. This bit is defined in Power ISA v3.1B to
be set if the interrupt occurred due to a prefixed instruction and
cleared otherwise for all interrupts except for instruction storage
interrupt, which does not come to the hypervisor. It is set to zero
for asynchronous interrupts such as external interrupts. In previous
ISA versions it was always set to 0 for all interrupts except
instruction storage interrupt.

The code in book3s_hv_rmhandlers.S that loads the faulting instruction
on a HDSI is only used on POWER8 and therefore doesn't ever need to
load a suffix.

[npiggin@gmail.com - check that the is-prefixed bit in SRR1 matches the
type of instruction that was fetched.]

Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/ZAgsq9h1CCzouQuV@cleo

show more ...

KVM: PPC: Permit SRR1 flags in more injected interrupt types

The prefix architecture in ISA v3.1 introduces a prefixed bit in SRR1
for many types of synchronous interrupts which is set when the inte

KVM: PPC: Permit SRR1 flags in more injected interrupt types

The prefix architecture in ISA v3.1 introduces a prefixed bit in SRR1
for many types of synchronous interrupts which is set when the interrupt
is caused by a prefixed instruction.

This requires KVM to be able to set this bit when injecting interrupts
into a guest. Plumb through the SRR1 "flags" argument to the core_queue
APIs where it's missing for this. For now they are set to 0, which is
no change.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fixup kvmppc_core_queue_alignment() in booke.c]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230330103224.3589928-2-npiggin@gmail.com

show more ...

KVM: Drop kvm_arch_check_processor_compat() hook

Drop kvm_arch_check_processor_compat() and its support code now that all
architecture implementations are nops.

Signed-off-by: Sean Christopherson <

KVM: Drop kvm_arch_check_processor_compat() hook

Drop kvm_arch_check_processor_compat() and its support code now that all
architecture implementations are nops.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Farman <farman@linux.ibm.com> # s390
Acked-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-Id: <20221130230934.1014142-33-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: PPC: Move processor compatibility check to module init

Move KVM PPC's compatibility checks to their respective module_init()
hooks, there's no need to wait until KVM's common compat check, nor

KVM: PPC: Move processor compatibility check to module init

Move KVM PPC's compatibility checks to their respective module_init()
hooks, there's no need to wait until KVM's common compat check, nor is
there a need to perform the check on every CPU (provided by common KVM's
hook), as the compatibility checks operate on global data.

arch/powerpc/include/asm/cputable.h: extern struct cpu_spec *cur_cpu_spec;
arch/powerpc/kvm/book3s.c: return 0
arch/powerpc/kvm/e500.c: strcmp(cur_cpu_spec->cpu_name, "e500v2")
arch/powerpc/kvm/e500mc.c: strcmp(cur_cpu_spec->cpu_name, "e500mc")
strcmp(cur_cpu_spec->cpu_name, "e5500")
strcmp(cur_cpu_spec->cpu_name, "e6500")

Cc: Fabiano Rosas <farosas@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Message-Id: <20221130230934.1014142-27-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: PPC: Avoid referencing userspace memory region in memslot updates

For PPC HV, get the number of pages directly from the new memslot instead
of computing the same from the userspace memory regio

KVM: PPC: Avoid referencing userspace memory region in memslot updates

For PPC HV, get the number of pages directly from the new memslot instead
of computing the same from the userspace memory region, and explicitly
check for !DELETE instead of inferring the same when toggling mmio_update.
The motivation for these changes is to avoid referencing the @mem param
so that it can be dropped in a future commit.

No functional change intended.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <1e97fb5198be25f98ef82e63a8d770c682264cc9.1638817639.git.maciej.szmigiero@oracle.com>

show more ...

KVM: Let/force architectures to deal with arch specific memslot data

Pass the "old" slot to kvm_arch_prepare_memory_region() and force arch
code to handle propagating arch specific data from "new" t

KVM: Let/force architectures to deal with arch specific memslot data

Pass the "old" slot to kvm_arch_prepare_memory_region() and force arch
code to handle propagating arch specific data from "new" to "old" when
necessary. This is a baby step towards dynamically allocating "new" from
the get go, and is a (very) minor performance boost on x86 due to not
unnecessarily copying arch data.

For PPC HV, copy the rmap in the !CREATE and !DELETE paths, i.e. for MOVE
and FLAGS_ONLY. This is functionally a nop as the previous behavior
would overwrite the pointer for CREATE, and eventually discard/ignore it
for DELETE.

For x86, copy the arch data only for FLAGS_ONLY changes. Unlike PPC HV,
x86 needs to reallocate arch data in the MOVE case as the size of x86's
allocations depend on the alignment of the memslot's gfn.

Opportunistically tweak kvm_arch_prepare_memory_region()'s param order to
match the "commit" prototype.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
[mss: add missing RISCV kvm_arch_prepare_memory_region() change]
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <67dea5f11bbcfd71e3da5986f11e87f5dd4013f9.1638817639.git.maciej.szmigiero@oracle.com>

show more ...

KVM: stats: Add halt_wait_ns stats for all architectures

Add simple stats halt_wait_ns to record the time a VCPU has spent on
waiting for all architectures (not just powerpc).

Signed-off-by: Jing Z

KVM: stats: Add halt_wait_ns stats for all architectures

Add simple stats halt_wait_ns to record the time a VCPU has spent on
waiting for all architectures (not just powerpc).

Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210802165633.1866976-5-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: stats: Support linear and logarithmic histogram statistics

Add new types of KVM stats, linear and logarithmic histogram.
Histogram are very useful for observing the value distribution
of time o

KVM: stats: Support linear and logarithmic histogram statistics

Add new types of KVM stats, linear and logarithmic histogram.
Histogram are very useful for observing the value distribution
of time or size related stats.

Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210802165633.1866976-2-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: debugfs: Reuse binary stats descriptors

To remove code duplication, use the binary stats descriptors in the
implementation of the debugfs interface for statistics. This unifies
the definition o

KVM: debugfs: Reuse binary stats descriptors

To remove code duplication, use the binary stats descriptors in the
implementation of the debugfs interface for statistics. This unifies
the definition of statistics for the binary and debugfs interfaces.

Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-8-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: stats: Support binary stats retrieval for a VCPU

Add a VCPU ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VCPU stats header,
desc

KVM: stats: Support binary stats retrieval for a VCPU

Add a VCPU ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VCPU stats header,
descriptors and data.
Define VCPU statistics descriptors and header for all architectures.

Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-5-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: stats: Support binary stats retrieval for a VM

Add a VM ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VM stats header,
descriptor

KVM: stats: Support binary stats retrieval for a VM

Add a VM ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VM stats header,
descriptors and data.
Define VM statistics descriptors and header for all architectures.

Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-4-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: stats: Separate generic stats from architecture specific ones

Generic KVM stats are those collected in architecture independent code
or those supported by all architectures; put all generic sta

KVM: stats: Separate generic stats from architecture specific ones

Generic KVM stats are those collected in architecture independent code
or those supported by all architectures; put all generic statistics in
a separate structure. This ensures that they are defined the same way
in the statistics API which is being added, removing duplication among
different architectures in the declaration of the descriptors.

No functional change intended.

Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-2-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: PPC: Book3S HV: Remove virt mode checks from real mode handlers

Now that the P7/8 path no longer supports radix, real-mode handlers
do not need to deal with being called in virt mode.

This cha

KVM: PPC: Book3S HV: Remove virt mode checks from real mode handlers

Now that the P7/8 path no longer supports radix, real-mode handlers
do not need to deal with being called in virt mode.

This change effectively reverts commit acde25726bc6 ("KVM: PPC: Book3S
HV: Add radix checks in real-mode hypercall handlers").

It removes a few more real-mode tests in rm hcall handlers, which
allows the indirect ops for the xive module to be removed from the
built-in xics rm handlers.

kvmppc_h_random is renamed to kvmppc_rm_h_random to be a bit more
descriptive and consistent with other rm handlers.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-25-npiggin@gmail.com

show more ...

KVM: PPC: Book3S HV P9: Stop handling hcalls in real-mode in the P9 path

In the interest of minimising the amount of code that is run in
"real-mode", don't handle hcalls in real mode in the P9 path.

KVM: PPC: Book3S HV P9: Stop handling hcalls in real-mode in the P9 path

In the interest of minimising the amount of code that is run in
"real-mode", don't handle hcalls in real mode in the P9 path. This
requires some new handlers for H_CEDE and xics-on-xive to be added
before xive is pulled or cede logic is checked.

This introduces a change in radix guest behaviour where radix guests
that execute 'sc 1' in userspace now get a privilege fault whereas
previously the 'sc 1' would be reflected as a syscall interrupt to the
guest kernel. That reflection is only required for hash guests that run
PR KVM.

Background:

In POWER8 and earlier processors, it is very expensive to exit from the
HV real mode context of a guest hypervisor interrupt, and switch to host
virtual mode. On those processors, guest->HV interrupts reach the
hypervisor with the MMU off because the MMU is loaded with guest context
(LPCR, SDR1, SLB), and the other threads in the sub-core need to be
pulled out of the guest too. Then the primary must save off guest state,
invalidate SLB and ERAT, and load up host state before the MMU can be
enabled to run in host virtual mode (~= regular Linux mode).

Hash guests also require a lot of hcalls to run due to the nature of the
MMU architecture and paravirtualisation design. The XICS interrupt
controller requires hcalls to run.

So KVM traditionally tries hard to avoid the full exit, by handling
hcalls and other interrupts in real mode as much as possible.

By contrast, POWER9 has independent MMU context per-thread, and in radix
mode the hypervisor is in host virtual memory mode when the HV interrupt
is taken. Radix guests do not require significant hcalls to manage their
translations, and xive guests don't need hcalls to handle interrupts. So
it's much less important for performance to handle hcalls in real mode on
POWER9.

One caveat is that the TCE hcalls are performance critical, real-mode
variants introduced for POWER8 in order to achieve 10GbE performance.
Real mode TCE hcalls were found to be less important on POWER9, which
was able to drive 40GBe networking without them (using the virt mode
hcalls) but performance is still important. These hcalls will benefit
from subsequent guest entry/exit optimisation including possibly a
faster "partial exit" that does not entirely switch to host context to
handle the hcall.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-14-npiggin@gmail.com

show more ...

KVM: PPC: Convert to the gfn-based MMU notifier callbacks

Move PPC to the gfn-base MMU notifier APIs, and update all 15 bajillion
PPC-internal hooks to work with gfns instead of hvas.

No meaningful

KVM: PPC: Convert to the gfn-based MMU notifier callbacks

Move PPC to the gfn-base MMU notifier APIs, and update all 15 bajillion
PPC-internal hooks to work with gfns instead of hvas.

No meaningful functional change intended, though the exact order of
operations is slightly different since the memslot lookups occur before
calling into arch code.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-6-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: PPC: Don't return -ENOTSUPP to userspace in ioctls

ENOTSUPP is a linux only thingy, the value of which is unknown to
userspace, not to be confused with ENOTSUP which linux maps to
EOPNOTSUPP, a

KVM: PPC: Don't return -ENOTSUPP to userspace in ioctls

ENOTSUPP is a linux only thingy, the value of which is unknown to
userspace, not to be confused with ENOTSUP which linux maps to
EOPNOTSUPP, as permitted by POSIX [1]:

[EOPNOTSUPP]
Operation not supported on socket. The type of socket (address family
or protocol) does not support the requested operation. A conforming
implementation may assign the same values for [EOPNOTSUPP] and [ENOTSUP].

Return -EOPNOTSUPP instead of -ENOTSUPP for the following ioctls:
- KVM_GET_FPU for Book3s and BookE
- KVM_SET_FPU for Book3s and BookE
- KVM_GET_DIRTY_LOG for BookE

This doesn't affect QEMU which doesn't call the KVM_GET_FPU and
KVM_SET_FPU ioctls on POWER anyway since they are not supported,
and _buggily_ ignores anything but -EPERM for KVM_GET_DIRTY_LOG.

[1] https://pubs.opengroup.org/onlinepubs/9699919799/functions/V2_chap02.html

Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

show more ...

KVM: PPC: Book3S HV: XICS: Replace the 'destroy' method by a 'release' method

Similarly to what was done with XICS-on-XIVE and XIVE native KVM devices
with commit 5422e95103cf ("KVM: PPC: Book3S HV:

KVM: PPC: Book3S HV: XICS: Replace the 'destroy' method by a 'release' method

Similarly to what was done with XICS-on-XIVE and XIVE native KVM devices
with commit 5422e95103cf ("KVM: PPC: Book3S HV: XIVE: Replace the 'destroy'
method by a 'release' method"), convert the historical XICS KVM device to
implement the 'release' method. This is needed to run nested guests with
an in-kernel IRQ chip. A typical POWER9 guest can select XICS or XIVE
during boot, which requires to be able to destroy and to re-create the
KVM device. Only the historical XICS KVM device is available under pseries
at the current time and it still uses the legacy 'destroy' method.

Switching to 'release' means that vCPUs might still be running when the
device is destroyed. In order to avoid potential use-after-free, the
kvmppc_xics structure is allocated on first usage and kept around until
the VM exits. The same pointer is used each time a KVM XICS device is
being created, but this is okay since we only have one per VM.

Clear the ICP of each vCPU with vcpu->mutex held. This ensures that the
next time the vCPU resumes execution, it won't be going into the XICS
code anymore.

Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

show more ...

KVM: Pass MMU notifier range flags to kvm_unmap_hva_range()

The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the

KVM: Pass MMU notifier range flags to kvm_unmap_hva_range()

The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the
case of kvm_mmu_notifier_invalidate_range_start(), this field is not
forwarded on to the architecture-specific implementation of
kvm_unmap_hva_range() and therefore the backend cannot sensibly decide
whether or not to block.

Add an extra 'flags' parameter to kvm_unmap_hva_range() so that
architectures are aware as to whether or not they are permitted to block.

Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-2-will@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: PPC: Clean up redundant 'kvm_run' parameters

In the current kvm version, 'kvm_run' has been included in the 'kvm_vcpu'
structure. For historical reasons, many kvm-related function parameters
re

KVM: PPC: Clean up redundant 'kvm_run' parameters

In the current kvm version, 'kvm_run' has been included in the 'kvm_vcpu'
structure. For historical reasons, many kvm-related function parameters
retain the 'kvm_run' and 'kvm_vcpu' parameters at the same time. This
patch does a unified cleanup of these remaining redundant parameters.

Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

show more ...

kvm_host: unify VM_STAT and VCPU_STAT definitions in a single place

The macros VM_STAT and VCPU_STAT are redundantly implemented in multiple
files, each used by a different architecure to initialize

kvm_host: unify VM_STAT and VCPU_STAT definitions in a single place

The macros VM_STAT and VCPU_STAT are redundantly implemented in multiple
files, each used by a different architecure to initialize the debugfs
entries for statistics. Since they all have the same purpose, they can be
unified in a single common definition in include/linux/kvm_host.h

Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20200414155625.20559-1-eesposit@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: PPC: Kill kvmppc_ops::mmu_destroy() and kvmppc_mmu_destroy()

These are only used by HV KVM and BookE, and in both cases they are
nops.

Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by:

KVM: PPC: Kill kvmppc_ops::mmu_destroy() and kvmppc_mmu_destroy()

These are only used by HV KVM and BookE, and in both cases they are
nops.

Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

show more ...

KVM: Provide common implementation for generic dirty log functions

Move the implementations of KVM_GET_DIRTY_LOG and KVM_CLEAR_DIRTY_LOG
for CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT into common KVM

KVM: Provide common implementation for generic dirty log functions

Move the implementations of KVM_GET_DIRTY_LOG and KVM_CLEAR_DIRTY_LOG
for CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT into common KVM code.
The arch specific implemenations are extremely similar, differing
only in whether the dirty log needs to be sync'd from hardware (x86)
and how the TLBs are flushed. Add new arch hooks to handle sync
and TLB flush; the sync will also be used for non-generic dirty log
support in a future patch (s390).

The ulterior motive for providing a common implementation is to
eliminate the dependency between arch and common code with respect to
the memslot referenced by the dirty log, i.e. to make it obvious in the
code that the validity of the memslot is guaranteed, as a future patch
will rework memslot handling such that id_to_memslot() can return NULL.

Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: Simplify kvm_free_memslot() and all its descendents

Now that all callers of kvm_free_memslot() pass NULL for @dont, remove
the param from the top-level routine and all arch's implementations.

KVM: Simplify kvm_free_memslot() and all its descendents

Now that all callers of kvm_free_memslot() pass NULL for @dont, remove
the param from the top-level routine and all arch's implementations.

No functional change intended.

Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: PPC: Move memslot memory allocation into prepare_memory_region()

Allocate the rmap array during kvm_arch_prepare_memory_region() to pave
the way for removing kvm_arch_create_memslot() altogethe

KVM: PPC: Move memslot memory allocation into prepare_memory_region()

Allocate the rmap array during kvm_arch_prepare_memory_region() to pave
the way for removing kvm_arch_create_memslot() altogether. Moving PPC's
memory allocation only changes the order of kernel memory allocations
between PPC and common KVM code.

No functional change intended.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...

KVM: Drop kvm_arch_vcpu_setup()

Remove kvm_arch_vcpu_setup() now that all arch specific implementations
are nops.

Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christoph

KVM: Drop kvm_arch_vcpu_setup()

Remove kvm_arch_vcpu_setup() now that all arch specific implementations
are nops.

Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

show more ...