| 80d8afca | 17-Jun-2024 |
Michael Walle <mwalle@kernel.org> |
ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
[ Upstream commit df35c6e9027cf9affe699e632a48082ab1bbba4c ]
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: im
ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
[ Upstream commit df35c6e9027cf9affe699e632a48082ab1bbba4c ]
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 5b2db0b4 | 17-Jun-2024 |
Michael Walle <mwalle@kernel.org> |
ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will ha
ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| e71469e2 | 17-Jun-2024 |
Michael Walle <mwalle@kernel.org> |
ARM: dts: imx6qdl-kontron-samx6i: fix board reset
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset,
ARM: dts: imx6qdl-kontron-samx6i: fix board reset
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 3b96e421 | 17-Jun-2024 |
Michael Walle <mwalle@kernel.org> |
ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use
ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 733d6599 | 14-Feb-2024 |
Michal Vokáč <michal.vokac@ysoft.com> |
ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch node
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ]
We identified that the PHYs actually do not work since commi
ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch node
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ]
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 20b18818 | 06-Dec-2023 |
Fabio Estevam <festevam@denx.de> |
ARM: dts: imx27-apf27dev: Fix LED name
[ Upstream commit dc35e253d032b959d92e12f081db5b00db26ae64 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-sch
ARM: dts: imx27-apf27dev: Fix LED name
[ Upstream commit dc35e253d032b959d92e12f081db5b00db26ae64 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 8b9b3d9d | 06-Dec-2023 |
Fabio Estevam <festevam@denx.de> |
ARM: dts: imx25/27: Pass timing0
[ Upstream commit 11ab7ad6f795ae23c398a4a5c56505d3dab27c4c ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change
ARM: dts: imx25/27: Pass timing0
[ Upstream commit 11ab7ad6f795ae23c398a4a5c56505d3dab27c4c ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 7eadf1ff | 06-Dec-2023 |
Fabio Estevam <festevam@denx.de> |
ARM: dts: imx25: Fix the iim compatible string
[ Upstream commit f0b929f58719fc57a4926ab4fc972f185453d6a5 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "f
ARM: dts: imx25: Fix the iim compatible string
[ Upstream commit f0b929f58719fc57a4926ab4fc972f185453d6a5 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 509c2239 | 06-Dec-2023 |
Fabio Estevam <festevam@denx.de> |
ARM: dts: imx1: Fix sram node
[ Upstream commit c248e535973088ba7071ff6f26ab7951143450af ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change
ARM: dts: imx1: Fix sram node
[ Upstream commit c248e535973088ba7071ff6f26ab7951143450af ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| cc156856 | 06-Dec-2023 |
Fabio Estevam <festevam@denx.de> |
ARM: dts: imx27: Fix sram node
[ Upstream commit 2fb7b2a2f06bb3f8321cf26c33e4e820c5b238b6 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-sch
ARM: dts: imx27: Fix sram node
[ Upstream commit 2fb7b2a2f06bb3f8321cf26c33e4e820c5b238b6 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 28743cc6 | 06-Dec-2023 |
Fabio Estevam <festevam@denx.de> |
ARM: dts: imx: Use flash@0,0 pattern
[ Upstream commit 1e1d7cc478fb16816de09740e3c323c0c188d58f ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the f
ARM: dts: imx: Use flash@0,0 pattern
[ Upstream commit 1e1d7cc478fb16816de09740e3c323c0c188d58f ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 401e139c | 12-Oct-2023 |
Alexander Stein <alexander.stein@ew.tq-group.com> |
ARM: dts: imx7s: Fix nand-controller #size-cells
[ Upstream commit 4aadb841ed49bada1415c48c44d21f5b69e01299 ]
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check
ARM: dts: imx7s: Fix nand-controller #size-cells
[ Upstream commit 4aadb841ed49bada1415c48c44d21f5b69e01299 ]
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: nand-controller@33002000:
#size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| aeefe740 | 12-Oct-2023 |
Alexander Stein <alexander.stein@ew.tq-group.com> |
ARM: dts: imx7s: Fix lcdif compatible
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL registe
ARM: dts: imx7s: Fix lcdif compatible
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|