1 /* 2 * (C) Copyright 2001 3 * Denis Peter, MPL AG Switzerland 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 * Note: Part of this code has been derived from linux 7 * 8 */ 9 #ifndef _USB_H_ 10 #define _USB_H_ 11 12 #include <usb_defs.h> 13 #include <linux/usb/ch9.h> 14 #include <asm/cache.h> 15 #include <part.h> 16 17 /* 18 * The EHCI spec says that we must align to at least 32 bytes. However, 19 * some platforms require larger alignment. 20 */ 21 #if ARCH_DMA_MINALIGN > 32 22 #define USB_DMA_MINALIGN ARCH_DMA_MINALIGN 23 #else 24 #define USB_DMA_MINALIGN 32 25 #endif 26 27 /* Everything is aribtrary */ 28 #define USB_ALTSETTINGALLOC 4 29 #define USB_MAXALTSETTING 128 /* Hard limit */ 30 31 #define USB_MAX_DEVICE 32 32 #define USB_MAXCONFIG 8 33 #define USB_MAXINTERFACES 8 34 #define USB_MAXENDPOINTS 16 35 #define USB_MAXCHILDREN 8 /* This is arbitrary */ 36 #define USB_MAX_HUB 16 37 38 #define USB_CNTL_TIMEOUT 100 /* 100ms timeout */ 39 40 /* 41 * This is the timeout to allow for submitting an urb in ms. We allow more 42 * time for a BULK device to react - some are slow. 43 */ 44 #define USB_TIMEOUT_MS(pipe) (usb_pipebulk(pipe) ? 5000 : 1000) 45 46 /* device request (setup) */ 47 struct devrequest { 48 unsigned char requesttype; 49 unsigned char request; 50 unsigned short value; 51 unsigned short index; 52 unsigned short length; 53 } __attribute__ ((packed)); 54 55 /* Interface */ 56 struct usb_interface { 57 struct usb_interface_descriptor desc; 58 59 unsigned char no_of_ep; 60 unsigned char num_altsetting; 61 unsigned char act_altsetting; 62 63 struct usb_endpoint_descriptor ep_desc[USB_MAXENDPOINTS]; 64 /* 65 * Super Speed Device will have Super Speed Endpoint 66 * Companion Descriptor (section 9.6.7 of usb 3.0 spec) 67 * Revision 1.0 June 6th 2011 68 */ 69 struct usb_ss_ep_comp_descriptor ss_ep_comp_desc[USB_MAXENDPOINTS]; 70 } __attribute__ ((packed)); 71 72 /* Configuration information.. */ 73 struct usb_config { 74 struct usb_config_descriptor desc; 75 76 unsigned char no_of_if; /* number of interfaces */ 77 struct usb_interface if_desc[USB_MAXINTERFACES]; 78 } __attribute__ ((packed)); 79 80 enum { 81 /* Maximum packet size; encoded as 0,1,2,3 = 8,16,32,64 */ 82 PACKET_SIZE_8 = 0, 83 PACKET_SIZE_16 = 1, 84 PACKET_SIZE_32 = 2, 85 PACKET_SIZE_64 = 3, 86 }; 87 88 struct usb_device { 89 int devnum; /* Device number on USB bus */ 90 int speed; /* full/low/high */ 91 char mf[32]; /* manufacturer */ 92 char prod[32]; /* product */ 93 char serial[32]; /* serial number */ 94 95 /* Maximum packet size; one of: PACKET_SIZE_* */ 96 int maxpacketsize; 97 /* one bit for each endpoint ([0] = IN, [1] = OUT) */ 98 unsigned int toggle[2]; 99 /* endpoint halts; one bit per endpoint # & direction; 100 * [0] = IN, [1] = OUT 101 */ 102 unsigned int halted[2]; 103 int epmaxpacketin[16]; /* INput endpoint specific maximums */ 104 int epmaxpacketout[16]; /* OUTput endpoint specific maximums */ 105 106 int configno; /* selected config number */ 107 /* Device Descriptor */ 108 struct usb_device_descriptor descriptor 109 __attribute__((aligned(ARCH_DMA_MINALIGN))); 110 struct usb_config config; /* config descriptor */ 111 112 int have_langid; /* whether string_langid is valid yet */ 113 int string_langid; /* language ID for strings */ 114 int (*irq_handle)(struct usb_device *dev); 115 unsigned long irq_status; 116 int irq_act_len; /* transfered bytes */ 117 void *privptr; 118 /* 119 * Child devices - if this is a hub device 120 * Each instance needs its own set of data structures. 121 */ 122 unsigned long status; 123 unsigned long int_pending; /* 1 bit per ep, used by int_queue */ 124 int act_len; /* transfered bytes */ 125 int maxchild; /* Number of ports if hub */ 126 int portnr; 127 struct usb_device *parent; 128 struct usb_device *children[USB_MAXCHILDREN]; 129 130 void *controller; /* hardware controller private data */ 131 /* slot_id - for xHCI enabled devices */ 132 unsigned int slot_id; 133 }; 134 135 struct int_queue; 136 137 /* 138 * You can initialize platform's USB host or device 139 * ports by passing this enum as an argument to 140 * board_usb_init(). 141 */ 142 enum usb_init_type { 143 USB_INIT_HOST, 144 USB_INIT_DEVICE 145 }; 146 147 /********************************************************************** 148 * this is how the lowlevel part communicate with the outer world 149 */ 150 151 #if defined(CONFIG_USB_UHCI) || defined(CONFIG_USB_OHCI) || \ 152 defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_OHCI_NEW) || \ 153 defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) || \ 154 defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ 155 defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) || \ 156 defined(CONFIG_USB_BLACKFIN) || defined(CONFIG_USB_AM35X) || \ 157 defined(CONFIG_USB_MUSB_DSPS) || defined(CONFIG_USB_MUSB_AM35X) || \ 158 defined(CONFIG_USB_MUSB_OMAP2PLUS) || defined(CONFIG_USB_MUSB_SUNXI) || \ 159 defined(CONFIG_USB_XHCI) || defined(CONFIG_USB_DWC2) 160 161 int usb_lowlevel_init(int index, enum usb_init_type init, void **controller); 162 int usb_lowlevel_stop(int index); 163 #ifdef CONFIG_MUSB_HOST 164 void usb_reset_root_port(void); 165 #else 166 #define usb_reset_root_port() 167 #endif 168 169 int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, 170 void *buffer, int transfer_len); 171 int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, 172 int transfer_len, struct devrequest *setup); 173 int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer, 174 int transfer_len, int interval); 175 176 #if defined CONFIG_USB_EHCI || defined CONFIG_MUSB_HOST 177 struct int_queue *create_int_queue(struct usb_device *dev, unsigned long pipe, 178 int queuesize, int elementsize, void *buffer, int interval); 179 int destroy_int_queue(struct usb_device *dev, struct int_queue *queue); 180 void *poll_int_queue(struct usb_device *dev, struct int_queue *queue); 181 #endif 182 183 /* Defines */ 184 #define USB_UHCI_VEND_ID 0x8086 185 #define USB_UHCI_DEV_ID 0x7112 186 187 /* 188 * PXA25x can only act as USB device. There are drivers 189 * which works with USB CDC gadgets implementations. 190 * Some of them have common routines which can be used 191 * in boards init functions e.g. udc_disconnect() used for 192 * forced device disconnection from host. 193 */ 194 #elif defined(CONFIG_USB_GADGET_PXA2XX) 195 196 extern void udc_disconnect(void); 197 198 #endif 199 200 /* 201 * board-specific hardware initialization, called by 202 * usb drivers and u-boot commands 203 * 204 * @param index USB controller number 205 * @param init initializes controller as USB host or device 206 */ 207 int board_usb_init(int index, enum usb_init_type init); 208 209 /* 210 * can be used to clean up after failed USB initialization attempt 211 * vide: board_usb_init() 212 * 213 * @param index USB controller number for selective cleanup 214 * @param init usb_init_type passed to board_usb_init() 215 */ 216 int board_usb_cleanup(int index, enum usb_init_type init); 217 218 #ifdef CONFIG_USB_STORAGE 219 220 #define USB_MAX_STOR_DEV 5 221 block_dev_desc_t *usb_stor_get_dev(int index); 222 int usb_stor_scan(int mode); 223 int usb_stor_info(void); 224 225 #endif 226 227 #ifdef CONFIG_USB_HOST_ETHER 228 229 #define USB_MAX_ETH_DEV 5 230 int usb_host_eth_scan(int mode); 231 232 #endif 233 234 #ifdef CONFIG_USB_KEYBOARD 235 236 int drv_usb_kbd_init(void); 237 int usb_kbd_deregister(int force); 238 239 #endif 240 /* routines */ 241 int usb_init(void); /* initialize the USB Controller */ 242 int usb_stop(void); /* stop the USB Controller */ 243 244 245 int usb_set_protocol(struct usb_device *dev, int ifnum, int protocol); 246 int usb_set_idle(struct usb_device *dev, int ifnum, int duration, 247 int report_id); 248 struct usb_device *usb_get_dev_index(int index); 249 int usb_control_msg(struct usb_device *dev, unsigned int pipe, 250 unsigned char request, unsigned char requesttype, 251 unsigned short value, unsigned short index, 252 void *data, unsigned short size, int timeout); 253 int usb_bulk_msg(struct usb_device *dev, unsigned int pipe, 254 void *data, int len, int *actual_length, int timeout); 255 int usb_submit_int_msg(struct usb_device *dev, unsigned long pipe, 256 void *buffer, int transfer_len, int interval); 257 int usb_disable_asynch(int disable); 258 int usb_maxpacket(struct usb_device *dev, unsigned long pipe); 259 int usb_get_configuration_no(struct usb_device *dev, unsigned char *buffer, 260 int cfgno); 261 int usb_get_report(struct usb_device *dev, int ifnum, unsigned char type, 262 unsigned char id, void *buf, int size); 263 int usb_get_class_descriptor(struct usb_device *dev, int ifnum, 264 unsigned char type, unsigned char id, void *buf, 265 int size); 266 int usb_clear_halt(struct usb_device *dev, int pipe); 267 int usb_string(struct usb_device *dev, int index, char *buf, size_t size); 268 int usb_set_interface(struct usb_device *dev, int interface, int alternate); 269 270 /* big endian -> little endian conversion */ 271 /* some CPUs are already little endian e.g. the ARM920T */ 272 #define __swap_16(x) \ 273 ({ unsigned short x_ = (unsigned short)x; \ 274 (unsigned short)( \ 275 ((x_ & 0x00FFU) << 8) | ((x_ & 0xFF00U) >> 8)); \ 276 }) 277 #define __swap_32(x) \ 278 ({ unsigned long x_ = (unsigned long)x; \ 279 (unsigned long)( \ 280 ((x_ & 0x000000FFUL) << 24) | \ 281 ((x_ & 0x0000FF00UL) << 8) | \ 282 ((x_ & 0x00FF0000UL) >> 8) | \ 283 ((x_ & 0xFF000000UL) >> 24)); \ 284 }) 285 286 #ifdef __LITTLE_ENDIAN 287 # define swap_16(x) (x) 288 # define swap_32(x) (x) 289 #else 290 # define swap_16(x) __swap_16(x) 291 # define swap_32(x) __swap_32(x) 292 #endif 293 294 /* 295 * Calling this entity a "pipe" is glorifying it. A USB pipe 296 * is something embarrassingly simple: it basically consists 297 * of the following information: 298 * - device number (7 bits) 299 * - endpoint number (4 bits) 300 * - current Data0/1 state (1 bit) 301 * - direction (1 bit) 302 * - speed (2 bits) 303 * - max packet size (2 bits: 8, 16, 32 or 64) 304 * - pipe type (2 bits: control, interrupt, bulk, isochronous) 305 * 306 * That's 18 bits. Really. Nothing more. And the USB people have 307 * documented these eighteen bits as some kind of glorious 308 * virtual data structure. 309 * 310 * Let's not fall in that trap. We'll just encode it as a simple 311 * unsigned int. The encoding is: 312 * 313 * - max size: bits 0-1 (00 = 8, 01 = 16, 10 = 32, 11 = 64) 314 * - direction: bit 7 (0 = Host-to-Device [Out], 315 * (1 = Device-to-Host [In]) 316 * - device: bits 8-14 317 * - endpoint: bits 15-18 318 * - Data0/1: bit 19 319 * - pipe type: bits 30-31 (00 = isochronous, 01 = interrupt, 320 * 10 = control, 11 = bulk) 321 * 322 * Why? Because it's arbitrary, and whatever encoding we select is really 323 * up to us. This one happens to share a lot of bit positions with the UHCI 324 * specification, so that much of the uhci driver can just mask the bits 325 * appropriately. 326 */ 327 /* Create various pipes... */ 328 #define create_pipe(dev,endpoint) \ 329 (((dev)->devnum << 8) | ((endpoint) << 15) | \ 330 (dev)->maxpacketsize) 331 #define default_pipe(dev) ((dev)->speed << 26) 332 333 #define usb_sndctrlpipe(dev, endpoint) ((PIPE_CONTROL << 30) | \ 334 create_pipe(dev, endpoint)) 335 #define usb_rcvctrlpipe(dev, endpoint) ((PIPE_CONTROL << 30) | \ 336 create_pipe(dev, endpoint) | \ 337 USB_DIR_IN) 338 #define usb_sndisocpipe(dev, endpoint) ((PIPE_ISOCHRONOUS << 30) | \ 339 create_pipe(dev, endpoint)) 340 #define usb_rcvisocpipe(dev, endpoint) ((PIPE_ISOCHRONOUS << 30) | \ 341 create_pipe(dev, endpoint) | \ 342 USB_DIR_IN) 343 #define usb_sndbulkpipe(dev, endpoint) ((PIPE_BULK << 30) | \ 344 create_pipe(dev, endpoint)) 345 #define usb_rcvbulkpipe(dev, endpoint) ((PIPE_BULK << 30) | \ 346 create_pipe(dev, endpoint) | \ 347 USB_DIR_IN) 348 #define usb_sndintpipe(dev, endpoint) ((PIPE_INTERRUPT << 30) | \ 349 create_pipe(dev, endpoint)) 350 #define usb_rcvintpipe(dev, endpoint) ((PIPE_INTERRUPT << 30) | \ 351 create_pipe(dev, endpoint) | \ 352 USB_DIR_IN) 353 #define usb_snddefctrl(dev) ((PIPE_CONTROL << 30) | \ 354 default_pipe(dev)) 355 #define usb_rcvdefctrl(dev) ((PIPE_CONTROL << 30) | \ 356 default_pipe(dev) | \ 357 USB_DIR_IN) 358 359 /* The D0/D1 toggle bits */ 360 #define usb_gettoggle(dev, ep, out) (((dev)->toggle[out] >> ep) & 1) 361 #define usb_dotoggle(dev, ep, out) ((dev)->toggle[out] ^= (1 << ep)) 362 #define usb_settoggle(dev, ep, out, bit) ((dev)->toggle[out] = \ 363 ((dev)->toggle[out] & \ 364 ~(1 << ep)) | ((bit) << ep)) 365 366 /* Endpoint halt control/status */ 367 #define usb_endpoint_out(ep_dir) (((ep_dir >> 7) & 1) ^ 1) 368 #define usb_endpoint_halt(dev, ep, out) ((dev)->halted[out] |= (1 << (ep))) 369 #define usb_endpoint_running(dev, ep, out) ((dev)->halted[out] &= ~(1 << (ep))) 370 #define usb_endpoint_halted(dev, ep, out) ((dev)->halted[out] & (1 << (ep))) 371 372 #define usb_packetid(pipe) (((pipe) & USB_DIR_IN) ? USB_PID_IN : \ 373 USB_PID_OUT) 374 375 #define usb_pipeout(pipe) ((((pipe) >> 7) & 1) ^ 1) 376 #define usb_pipein(pipe) (((pipe) >> 7) & 1) 377 #define usb_pipedevice(pipe) (((pipe) >> 8) & 0x7f) 378 #define usb_pipe_endpdev(pipe) (((pipe) >> 8) & 0x7ff) 379 #define usb_pipeendpoint(pipe) (((pipe) >> 15) & 0xf) 380 #define usb_pipedata(pipe) (((pipe) >> 19) & 1) 381 #define usb_pipetype(pipe) (((pipe) >> 30) & 3) 382 #define usb_pipeisoc(pipe) (usb_pipetype((pipe)) == PIPE_ISOCHRONOUS) 383 #define usb_pipeint(pipe) (usb_pipetype((pipe)) == PIPE_INTERRUPT) 384 #define usb_pipecontrol(pipe) (usb_pipetype((pipe)) == PIPE_CONTROL) 385 #define usb_pipebulk(pipe) (usb_pipetype((pipe)) == PIPE_BULK) 386 387 #define usb_pipe_ep_index(pipe) \ 388 usb_pipecontrol(pipe) ? (usb_pipeendpoint(pipe) * 2) : \ 389 ((usb_pipeendpoint(pipe) * 2) - \ 390 (usb_pipein(pipe) ? 0 : 1)) 391 392 /************************************************************************* 393 * Hub Stuff 394 */ 395 struct usb_port_status { 396 unsigned short wPortStatus; 397 unsigned short wPortChange; 398 } __attribute__ ((packed)); 399 400 struct usb_hub_status { 401 unsigned short wHubStatus; 402 unsigned short wHubChange; 403 } __attribute__ ((packed)); 404 405 406 /* Hub descriptor */ 407 struct usb_hub_descriptor { 408 unsigned char bLength; 409 unsigned char bDescriptorType; 410 unsigned char bNbrPorts; 411 unsigned short wHubCharacteristics; 412 unsigned char bPwrOn2PwrGood; 413 unsigned char bHubContrCurrent; 414 unsigned char DeviceRemovable[(USB_MAXCHILDREN+1+7)/8]; 415 unsigned char PortPowerCtrlMask[(USB_MAXCHILDREN+1+7)/8]; 416 /* DeviceRemovable and PortPwrCtrlMask want to be variable-length 417 bitmaps that hold max 255 entries. (bit0 is ignored) */ 418 } __attribute__ ((packed)); 419 420 421 struct usb_hub_device { 422 struct usb_device *pusb_dev; 423 struct usb_hub_descriptor desc; 424 }; 425 426 int usb_hub_probe(struct usb_device *dev, int ifnum); 427 void usb_hub_reset(void); 428 int hub_port_reset(struct usb_device *dev, int port, 429 unsigned short *portstat); 430 431 struct usb_device *usb_alloc_new_device(void *controller); 432 433 int usb_new_device(struct usb_device *dev); 434 void usb_free_device(void); 435 int usb_alloc_device(struct usb_device *dev); 436 437 #endif /*_USB_H_ */ 438