1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2001 4 * Denis Peter, MPL AG Switzerland 5 * 6 * Most of these definitions are derived from 7 * linux/drivers/scsi/sym53c8xx_defs.h 8 */ 9 10 #ifndef _SYM53C8XX_DEFS_H 11 #define _SYM53C8XX_DEFS_H 12 13 14 #define SCNTL0 0x00 /* full arb., ena parity, par->ATN */ 15 16 #define SCNTL1 0x01 /* no reset */ 17 #define ISCON 0x10 /* connected to scsi */ 18 #define CRST 0x08 /* force reset */ 19 #define IARB 0x02 /* immediate arbitration */ 20 21 #define SCNTL2 0x02 /* no disconnect expected */ 22 #define SDU 0x80 /* cmd: disconnect will raise error */ 23 #define CHM 0x40 /* sta: chained mode */ 24 #define WSS 0x08 /* sta: wide scsi send [W]*/ 25 #define WSR 0x01 /* sta: wide scsi received [W]*/ 26 27 #define SCNTL3 0x03 /* cnf system clock dependent */ 28 #define EWS 0x08 /* cmd: enable wide scsi [W]*/ 29 #define ULTRA 0x80 /* cmd: ULTRA enable */ 30 /* bits 0-2, 7 rsvd for C1010 */ 31 32 #define SCID 0x04 /* cnf host adapter scsi address */ 33 #define RRE 0x40 /* r/w:e enable response to resel. */ 34 #define SRE 0x20 /* r/w:e enable response to select */ 35 36 #define SXFER 0x05 /* ### Sync speed and count */ 37 /* bits 6-7 rsvd for C1010 */ 38 39 #define SDID 0x06 /* ### Destination-ID */ 40 41 #define GPREG 0x07 /* ??? IO-Pins */ 42 43 #define SFBR 0x08 /* ### First byte in phase */ 44 45 #define SOCL 0x09 46 #define CREQ 0x80 /* r/w: SCSI-REQ */ 47 #define CACK 0x40 /* r/w: SCSI-ACK */ 48 #define CBSY 0x20 /* r/w: SCSI-BSY */ 49 #define CSEL 0x10 /* r/w: SCSI-SEL */ 50 #define CATN 0x08 /* r/w: SCSI-ATN */ 51 #define CMSG 0x04 /* r/w: SCSI-MSG */ 52 #define CC_D 0x02 /* r/w: SCSI-C_D */ 53 #define CI_O 0x01 /* r/w: SCSI-I_O */ 54 55 #define SSID 0x0a 56 57 #define SBCL 0x0b 58 59 #define DSTAT 0x0c 60 #define DFE 0x80 /* sta: dma fifo empty */ 61 #define MDPE 0x40 /* int: master data parity error */ 62 #define BF 0x20 /* int: script: bus fault */ 63 #define ABRT 0x10 /* int: script: command aborted */ 64 #define SSI 0x08 /* int: script: single step */ 65 #define SIR 0x04 /* int: script: interrupt instruct. */ 66 #define IID 0x01 /* int: script: illegal instruct. */ 67 68 #define SSTAT0 0x0d 69 #define ILF 0x80 /* sta: data in SIDL register lsb */ 70 #define ORF 0x40 /* sta: data in SODR register lsb */ 71 #define OLF 0x20 /* sta: data in SODL register lsb */ 72 #define AIP 0x10 /* sta: arbitration in progress */ 73 #define LOA 0x08 /* sta: arbitration lost */ 74 #define WOA 0x04 /* sta: arbitration won */ 75 #define IRST 0x02 /* sta: scsi reset signal */ 76 #define SDP 0x01 /* sta: scsi parity signal */ 77 78 #define SSTAT1 0x0e 79 #define FF3210 0xf0 /* sta: bytes in the scsi fifo */ 80 81 #define SSTAT2 0x0f 82 #define ILF1 0x80 /* sta: data in SIDL register msb[W]*/ 83 #define ORF1 0x40 /* sta: data in SODR register msb[W]*/ 84 #define OLF1 0x20 /* sta: data in SODL register msb[W]*/ 85 #define DM 0x04 /* sta: DIFFSENS mismatch (895/6 only) */ 86 #define LDSC 0x02 /* sta: disconnect & reconnect */ 87 88 #define DSA 0x10 /* --> Base page */ 89 #define DSA1 0x11 90 #define DSA2 0x12 91 #define DSA3 0x13 92 93 #define ISTAT 0x14 /* --> Main Command and status */ 94 #define CABRT 0x80 /* cmd: abort current operation */ 95 #define SRST 0x40 /* mod: reset chip */ 96 #define SIGP 0x20 /* r/w: message from host to ncr */ 97 #define SEM 0x10 /* r/w: message between host + ncr */ 98 #define CON 0x08 /* sta: connected to scsi */ 99 #define INTF 0x04 /* sta: int on the fly (reset by wr)*/ 100 #define SIP 0x02 /* sta: scsi-interrupt */ 101 #define DIP 0x01 /* sta: host/script interrupt */ 102 103 104 #define CTEST0 0x18 105 #define CTEST1 0x19 106 #define CTEST2 0x1a 107 #define CSIGP 0x40 108 /* bits 0-2,7 rsvd for C1010 */ 109 110 #define CTEST3 0x1b 111 #define FLF 0x08 /* cmd: flush dma fifo */ 112 #define CLF 0x04 /* cmd: clear dma fifo */ 113 #define FM 0x02 /* mod: fetch pin mode */ 114 #define WRIE 0x01 /* mod: write and invalidate enable */ 115 /* bits 4-7 rsvd for C1010 */ 116 117 #define DFIFO 0x20 118 #define CTEST4 0x21 119 #define BDIS 0x80 /* mod: burst disable */ 120 #define MPEE 0x08 /* mod: master parity error enable */ 121 122 #define CTEST5 0x22 123 #define DFS 0x20 /* mod: dma fifo size */ 124 /* bits 0-1, 3-7 rsvd for C1010 */ 125 #define CTEST6 0x23 126 127 #define DBC 0x24 /* ### Byte count and command */ 128 #define DNAD 0x28 /* ### Next command register */ 129 #define DSP 0x2c /* --> Script Pointer */ 130 #define DSPS 0x30 /* --> Script pointer save/opcode#2 */ 131 132 #define SCRATCHA 0x34 /* Temporary register a */ 133 #define SCRATCHA1 0x35 134 #define SCRATCHA2 0x36 135 #define SCRATCHA3 0x37 136 137 #define DMODE 0x38 138 #define BL_2 0x80 /* mod: burst length shift value +2 */ 139 #define BL_1 0x40 /* mod: burst length shift value +1 */ 140 #define ERL 0x08 /* mod: enable read line */ 141 #define ERMP 0x04 /* mod: enable read multiple */ 142 #define BOF 0x02 /* mod: burst op code fetch */ 143 #define MAN 0x01 /* mod: manual start */ 144 145 #define DIEN 0x39 146 #define SBR 0x3a 147 148 #define DCNTL 0x3b /* --> Script execution control */ 149 #define CLSE 0x80 /* mod: cache line size enable */ 150 #define PFF 0x40 /* cmd: pre-fetch flush */ 151 #define PFEN 0x20 /* mod: pre-fetch enable */ 152 #define SSM 0x10 /* mod: single step mode */ 153 #define IRQM 0x08 /* mod: irq mode (1 = totem pole !) */ 154 #define STD 0x04 /* cmd: start dma mode */ 155 #define IRQD 0x02 /* mod: irq disable */ 156 #define NOCOM 0x01 /* cmd: protect sfbr while reselect */ 157 /* bits 0-1 rsvd for C1010 */ 158 159 #define ADDER 0x3c 160 161 #define SIEN 0x40 /* -->: interrupt enable */ 162 #define SIST 0x42 /* <--: interrupt status */ 163 #define SBMC 0x1000/* sta: SCSI Bus Mode Change (895/6 only) */ 164 #define STO 0x0400/* sta: timeout (select) */ 165 #define GEN 0x0200/* sta: timeout (general) */ 166 #define HTH 0x0100/* sta: timeout (handshake) */ 167 #define MA 0x80 /* sta: phase mismatch */ 168 #define CMP 0x40 /* sta: arbitration complete */ 169 #define SEL 0x20 /* sta: selected by another device */ 170 #define RSL 0x10 /* sta: reselected by another device*/ 171 #define SGE 0x08 /* sta: gross error (over/underflow)*/ 172 #define UDC 0x04 /* sta: unexpected disconnect */ 173 #define RST 0x02 /* sta: scsi bus reset detected */ 174 #define PAR 0x01 /* sta: scsi parity error */ 175 176 #define SLPAR 0x44 177 #define SWIDE 0x45 178 #define MACNTL 0x46 179 #define GPCNTL 0x47 180 #define STIME0 0x48 /* cmd: timeout for select&handshake*/ 181 #define STIME1 0x49 /* cmd: timeout user defined */ 182 #define RESPID 0x4a /* sta: Reselect-IDs */ 183 184 #define STEST0 0x4c 185 186 #define STEST1 0x4d 187 #define SCLK 0x80 /* Use the PCI clock as SCSI clock */ 188 #define DBLEN 0x08 /* clock doubler running */ 189 #define DBLSEL 0x04 /* clock doubler selected */ 190 191 192 #define STEST2 0x4e 193 #define ROF 0x40 /* reset scsi offset (after gross error!) */ 194 #define EXT 0x02 /* extended filtering */ 195 196 #define STEST3 0x4f 197 #define TE 0x80 /* c: tolerAnt enable */ 198 #define HSC 0x20 /* c: Halt SCSI Clock */ 199 #define CSF 0x02 /* c: clear scsi fifo */ 200 201 #define SIDL 0x50 /* Lowlevel: latched from scsi data */ 202 #define STEST4 0x52 203 #define SMODE 0xc0 /* SCSI bus mode (895/6 only) */ 204 #define SMODE_HVD 0x40 /* High Voltage Differential */ 205 #define SMODE_SE 0x80 /* Single Ended */ 206 #define SMODE_LVD 0xc0 /* Low Voltage Differential */ 207 #define LCKFRQ 0x20 /* Frequency Lock (895/6 only) */ 208 /* bits 0-5 rsvd for C1010 */ 209 210 #define SODL 0x54 /* Lowlevel: data out to scsi data */ 211 212 #define SBDL 0x58 /* Lowlevel: data from scsi data */ 213 214 215 /*----------------------------------------------------------- 216 ** 217 ** Utility macros for the script. 218 ** 219 **----------------------------------------------------------- 220 */ 221 222 #define REG(r) (r) 223 224 /*----------------------------------------------------------- 225 ** 226 ** SCSI phases 227 ** 228 ** DT phases illegal for ncr driver. 229 ** 230 **----------------------------------------------------------- 231 */ 232 233 #define SCR_DATA_OUT 0x00000000 234 #define SCR_DATA_IN 0x01000000 235 #define SCR_COMMAND 0x02000000 236 #define SCR_STATUS 0x03000000 237 #define SCR_DT_DATA_OUT 0x04000000 238 #define SCR_DT_DATA_IN 0x05000000 239 #define SCR_MSG_OUT 0x06000000 240 #define SCR_MSG_IN 0x07000000 241 242 #define SCR_ILG_OUT 0x04000000 243 #define SCR_ILG_IN 0x05000000 244 245 /*----------------------------------------------------------- 246 ** 247 ** Data transfer via SCSI. 248 ** 249 **----------------------------------------------------------- 250 ** 251 ** MOVE_ABS (LEN) 252 ** <<start address>> 253 ** 254 ** MOVE_IND (LEN) 255 ** <<dnad_offset>> 256 ** 257 ** MOVE_TBL 258 ** <<dnad_offset>> 259 ** 260 **----------------------------------------------------------- 261 */ 262 263 #define OPC_MOVE 0x08000000 264 265 #define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l)) 266 #define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l)) 267 #define SCR_MOVE_TBL (0x10000000 | OPC_MOVE) 268 269 #define SCR_CHMOV_ABS(l) ((0x00000000) | (l)) 270 #define SCR_CHMOV_IND(l) ((0x20000000) | (l)) 271 #define SCR_CHMOV_TBL (0x10000000) 272 273 274 /*----------------------------------------------------------- 275 ** 276 ** Selection 277 ** 278 **----------------------------------------------------------- 279 ** 280 ** SEL_ABS | SCR_ID (0..15) [ | REL_JMP] 281 ** <<alternate_address>> 282 ** 283 ** SEL_TBL | << dnad_offset>> [ | REL_JMP] 284 ** <<alternate_address>> 285 ** 286 **----------------------------------------------------------- 287 */ 288 289 #define SCR_SEL_ABS 0x40000000 290 #define SCR_SEL_ABS_ATN 0x41000000 291 #define SCR_SEL_TBL 0x42000000 292 #define SCR_SEL_TBL_ATN 0x43000000 293 294 295 #define SCR_JMP_REL 0x04000000 296 #define SCR_ID(id) (((unsigned long)(id)) << 16) 297 298 /*----------------------------------------------------------- 299 ** 300 ** Waiting for Disconnect or Reselect 301 ** 302 **----------------------------------------------------------- 303 ** 304 ** WAIT_DISC 305 ** dummy: <<alternate_address>> 306 ** 307 ** WAIT_RESEL 308 ** <<alternate_address>> 309 ** 310 **----------------------------------------------------------- 311 */ 312 313 #define SCR_WAIT_DISC 0x48000000 314 #define SCR_WAIT_RESEL 0x50000000 315 316 /*----------------------------------------------------------- 317 ** 318 ** Bit Set / Reset 319 ** 320 **----------------------------------------------------------- 321 ** 322 ** SET (flags {|.. }) 323 ** 324 ** CLR (flags {|.. }) 325 ** 326 **----------------------------------------------------------- 327 */ 328 329 #define SCR_SET(f) (0x58000000 | (f)) 330 #define SCR_CLR(f) (0x60000000 | (f)) 331 332 #define SCR_CARRY 0x00000400 333 #define SCR_TRG 0x00000200 334 #define SCR_ACK 0x00000040 335 #define SCR_ATN 0x00000008 336 337 338 /*----------------------------------------------------------- 339 ** 340 ** Memory to memory move 341 ** 342 **----------------------------------------------------------- 343 ** 344 ** COPY (bytecount) 345 ** << source_address >> 346 ** << destination_address >> 347 ** 348 ** SCR_COPY sets the NO FLUSH option by default. 349 ** SCR_COPY_F does not set this option. 350 ** 351 ** For chips which do not support this option, 352 ** ncr_copy_and_bind() will remove this bit. 353 **----------------------------------------------------------- 354 */ 355 356 #define SCR_NO_FLUSH 0x01000000 357 358 #define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n)) 359 #define SCR_COPY_F(n) (0xc0000000 | (n)) 360 361 /*----------------------------------------------------------- 362 ** 363 ** Register move and binary operations 364 ** 365 **----------------------------------------------------------- 366 ** 367 ** SFBR_REG (reg, op, data) reg = SFBR op data 368 ** << 0 >> 369 ** 370 ** REG_SFBR (reg, op, data) SFBR = reg op data 371 ** << 0 >> 372 ** 373 ** REG_REG (reg, op, data) reg = reg op data 374 ** << 0 >> 375 ** 376 **----------------------------------------------------------- 377 ** On 810A, 860, 825A, 875, 895 and 896 chips the content 378 ** of SFBR register can be used as data (SCR_SFBR_DATA). 379 ** The 896 has additionnal IO registers starting at 380 ** offset 0x80. Bit 7 of register offset is stored in 381 ** bit 7 of the SCRIPTS instruction first DWORD. 382 **----------------------------------------------------------- 383 */ 384 385 #define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul)) /* + ((ofs) & 0x80)) */ 386 387 #define SCR_SFBR_REG(reg,op,data) \ 388 (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) 389 390 #define SCR_REG_SFBR(reg,op,data) \ 391 (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) 392 393 #define SCR_REG_REG(reg,op,data) \ 394 (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) 395 396 397 #define SCR_LOAD 0x00000000 398 #define SCR_SHL 0x01000000 399 #define SCR_OR 0x02000000 400 #define SCR_XOR 0x03000000 401 #define SCR_AND 0x04000000 402 #define SCR_SHR 0x05000000 403 #define SCR_ADD 0x06000000 404 #define SCR_ADDC 0x07000000 405 406 #define SCR_SFBR_DATA (0x00800000>>8ul) /* Use SFBR as data */ 407 408 /*----------------------------------------------------------- 409 ** 410 ** FROM_REG (reg) SFBR = reg 411 ** << 0 >> 412 ** 413 ** TO_REG (reg) reg = SFBR 414 ** << 0 >> 415 ** 416 ** LOAD_REG (reg, data) reg = <data> 417 ** << 0 >> 418 ** 419 ** LOAD_SFBR(data) SFBR = <data> 420 ** << 0 >> 421 ** 422 **----------------------------------------------------------- 423 */ 424 425 #define SCR_FROM_REG(reg) \ 426 SCR_REG_SFBR(reg,SCR_OR,0) 427 428 #define SCR_TO_REG(reg) \ 429 SCR_SFBR_REG(reg,SCR_OR,0) 430 431 #define SCR_LOAD_REG(reg,data) \ 432 SCR_REG_REG(reg,SCR_LOAD,data) 433 434 #define SCR_LOAD_SFBR(data) \ 435 (SCR_REG_SFBR (gpreg, SCR_LOAD, data)) 436 437 /*----------------------------------------------------------- 438 ** 439 ** LOAD from memory to register. 440 ** STORE from register to memory. 441 ** 442 ** Only supported by 810A, 860, 825A, 875, 895 and 896. 443 ** 444 **----------------------------------------------------------- 445 ** 446 ** LOAD_ABS (LEN) 447 ** <<start address>> 448 ** 449 ** LOAD_REL (LEN) (DSA relative) 450 ** <<dsa_offset>> 451 ** 452 **----------------------------------------------------------- 453 */ 454 455 #define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul) 456 #define SCR_NO_FLUSH2 0x02000000 457 #define SCR_DSA_REL2 0x10000000 458 459 #define SCR_LOAD_R(reg, how, n) \ 460 (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) 461 462 #define SCR_STORE_R(reg, how, n) \ 463 (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) 464 465 #define SCR_LOAD_ABS(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2, n) 466 #define SCR_LOAD_REL(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n) 467 #define SCR_LOAD_ABS_F(reg, n) SCR_LOAD_R(reg, 0, n) 468 #define SCR_LOAD_REL_F(reg, n) SCR_LOAD_R(reg, SCR_DSA_REL2, n) 469 470 #define SCR_STORE_ABS(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2, n) 471 #define SCR_STORE_REL(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n) 472 #define SCR_STORE_ABS_F(reg, n) SCR_STORE_R(reg, 0, n) 473 #define SCR_STORE_REL_F(reg, n) SCR_STORE_R(reg, SCR_DSA_REL2, n) 474 475 476 /*----------------------------------------------------------- 477 ** 478 ** Waiting for Disconnect or Reselect 479 ** 480 **----------------------------------------------------------- 481 ** 482 ** JUMP [ | IFTRUE/IFFALSE ( ... ) ] 483 ** <<address>> 484 ** 485 ** JUMPR [ | IFTRUE/IFFALSE ( ... ) ] 486 ** <<distance>> 487 ** 488 ** CALL [ | IFTRUE/IFFALSE ( ... ) ] 489 ** <<address>> 490 ** 491 ** CALLR [ | IFTRUE/IFFALSE ( ... ) ] 492 ** <<distance>> 493 ** 494 ** RETURN [ | IFTRUE/IFFALSE ( ... ) ] 495 ** <<dummy>> 496 ** 497 ** INT [ | IFTRUE/IFFALSE ( ... ) ] 498 ** <<ident>> 499 ** 500 ** INT_FLY [ | IFTRUE/IFFALSE ( ... ) ] 501 ** <<ident>> 502 ** 503 ** Conditions: 504 ** WHEN (phase) 505 ** IF (phase) 506 ** CARRYSET 507 ** DATA (data, mask) 508 ** 509 **----------------------------------------------------------- 510 */ 511 512 #define SCR_NO_OP 0x80000000 513 #define SCR_JUMP 0x80080000 514 #define SCR_JUMP64 0x80480000 515 #define SCR_JUMPR 0x80880000 516 #define SCR_CALL 0x88080000 517 #define SCR_CALLR 0x88880000 518 #define SCR_RETURN 0x90080000 519 #define SCR_INT 0x98080000 520 #define SCR_INT_FLY 0x98180000 521 522 #define IFFALSE(arg) (0x00080000 | (arg)) 523 #define IFTRUE(arg) (0x00000000 | (arg)) 524 525 #define WHEN(phase) (0x00030000 | (phase)) 526 #define IF(phase) (0x00020000 | (phase)) 527 528 #define DATA(D) (0x00040000 | ((D) & 0xff)) 529 #define MASK(D,M) (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff)) 530 531 #define CARRYSET (0x00200000) 532 533 534 #define SIR_COMPLETE 0x10000000 535 /* script errors */ 536 #define SIR_SEL_ATN_NO_MSG_OUT 0x00000001 537 #define SIR_CMD_OUT_ILL_PH 0x00000002 538 #define SIR_STATUS_ILL_PH 0x00000003 539 #define SIR_MSG_RECEIVED 0x00000004 540 #define SIR_DATA_IN_ERR 0x00000005 541 #define SIR_DATA_OUT_ERR 0x00000006 542 #define SIR_SCRIPT_ERROR 0x00000007 543 #define SIR_MSG_OUT_NO_CMD 0x00000008 544 #define SIR_MSG_OVER7 0x00000009 545 /* Fly interrupt */ 546 #define INT_ON_FY 0x00000080 547 548 /* Hardware errors are defined in scsi.h */ 549 550 #define SCSI_IDENTIFY 0xC0 551 552 #endif 553