1 /* 2 * NS16550 Serial Port 3 * originally from linux source (arch/powerpc/boot/ns16550.h) 4 * 5 * Cleanup and unification 6 * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH 7 * 8 * modified slightly to 9 * have addresses as offsets from CONFIG_SYS_ISA_BASE 10 * added a few more definitions 11 * added prototypes for ns16550.c 12 * reduced no of com ports to 2 13 * modifications (c) Rob Taylor, Flying Pig Systems. 2000. 14 * 15 * added support for port on 64-bit bus 16 * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems 17 */ 18 19 /* 20 * Note that the following macro magic uses the fact that the compiler 21 * will not allocate storage for arrays of size 0 22 */ 23 24 #include <linux/types.h> 25 26 #if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0) 27 #error "Please define NS16550 registers size." 28 #elif defined(CONFIG_SYS_NS16550_MEM32) 29 #define UART_REG(x) u32 x 30 #elif (CONFIG_SYS_NS16550_REG_SIZE > 0) 31 #define UART_REG(x) \ 32 unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \ 33 unsigned char x; 34 #elif (CONFIG_SYS_NS16550_REG_SIZE < 0) 35 #define UART_REG(x) \ 36 unsigned char x; \ 37 unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1]; 38 #endif 39 40 struct NS16550 { 41 UART_REG(rbr); /* 0 */ 42 UART_REG(ier); /* 1 */ 43 UART_REG(fcr); /* 2 */ 44 UART_REG(lcr); /* 3 */ 45 UART_REG(mcr); /* 4 */ 46 UART_REG(lsr); /* 5 */ 47 UART_REG(msr); /* 6 */ 48 UART_REG(spr); /* 7 */ 49 UART_REG(mdr1); /* 8 */ 50 UART_REG(reg9); /* 9 */ 51 UART_REG(regA); /* A */ 52 UART_REG(regB); /* B */ 53 UART_REG(regC); /* C */ 54 UART_REG(regD); /* D */ 55 UART_REG(regE); /* E */ 56 UART_REG(uasr); /* F */ 57 UART_REG(scr); /* 10*/ 58 UART_REG(ssr); /* 11*/ 59 UART_REG(reg12); /* 12*/ 60 UART_REG(osc_12m_sel); /* 13*/ 61 }; 62 63 #define thr rbr 64 #define iir fcr 65 #define dll rbr 66 #define dlm ier 67 68 typedef volatile struct NS16550 *NS16550_t; 69 70 /* 71 * These are the definitions for the FIFO Control Register 72 */ 73 #define UART_FCR_FIFO_EN 0x01 /* Fifo enable */ 74 #define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ 75 #define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ 76 #define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ 77 #define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ 78 #define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ 79 #define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ 80 #define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ 81 #define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ 82 83 #define UART_FCR_RXSR 0x02 /* Receiver soft reset */ 84 #define UART_FCR_TXSR 0x04 /* Transmitter soft reset */ 85 86 /* 87 * These are the definitions for the Modem Control Register 88 */ 89 #define UART_MCR_DTR 0x01 /* DTR */ 90 #define UART_MCR_RTS 0x02 /* RTS */ 91 #define UART_MCR_OUT1 0x04 /* Out 1 */ 92 #define UART_MCR_OUT2 0x08 /* Out 2 */ 93 #define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ 94 95 #define UART_MCR_DMA_EN 0x04 96 #define UART_MCR_TX_DFR 0x08 97 98 /* 99 * These are the definitions for the Line Control Register 100 * 101 * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting 102 * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. 103 */ 104 #define UART_LCR_WLS_MSK 0x03 /* character length select mask */ 105 #define UART_LCR_WLS_5 0x00 /* 5 bit character length */ 106 #define UART_LCR_WLS_6 0x01 /* 6 bit character length */ 107 #define UART_LCR_WLS_7 0x02 /* 7 bit character length */ 108 #define UART_LCR_WLS_8 0x03 /* 8 bit character length */ 109 #define UART_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */ 110 #define UART_LCR_PEN 0x08 /* Parity eneble */ 111 #define UART_LCR_EPS 0x10 /* Even Parity Select */ 112 #define UART_LCR_STKP 0x20 /* Stick Parity */ 113 #define UART_LCR_SBRK 0x40 /* Set Break */ 114 #define UART_LCR_BKSE 0x80 /* Bank select enable */ 115 #define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ 116 117 /* 118 * These are the definitions for the Line Status Register 119 */ 120 #define UART_LSR_DR 0x01 /* Data ready */ 121 #define UART_LSR_OE 0x02 /* Overrun */ 122 #define UART_LSR_PE 0x04 /* Parity error */ 123 #define UART_LSR_FE 0x08 /* Framing error */ 124 #define UART_LSR_BI 0x10 /* Break */ 125 #define UART_LSR_THRE 0x20 /* Xmit holding register empty */ 126 #define UART_LSR_TEMT 0x40 /* Xmitter empty */ 127 #define UART_LSR_ERR 0x80 /* Error */ 128 129 #define UART_MSR_DCD 0x80 /* Data Carrier Detect */ 130 #define UART_MSR_RI 0x40 /* Ring Indicator */ 131 #define UART_MSR_DSR 0x20 /* Data Set Ready */ 132 #define UART_MSR_CTS 0x10 /* Clear to Send */ 133 #define UART_MSR_DDCD 0x08 /* Delta DCD */ 134 #define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ 135 #define UART_MSR_DDSR 0x02 /* Delta DSR */ 136 #define UART_MSR_DCTS 0x01 /* Delta CTS */ 137 138 /* 139 * These are the definitions for the Interrupt Identification Register 140 */ 141 #define UART_IIR_NO_INT 0x01 /* No interrupts pending */ 142 #define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ 143 144 #define UART_IIR_MSI 0x00 /* Modem status interrupt */ 145 #define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ 146 #define UART_IIR_RDI 0x04 /* Receiver data interrupt */ 147 #define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ 148 149 /* 150 * These are the definitions for the Interrupt Enable Register 151 */ 152 #define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ 153 #define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ 154 #define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ 155 #define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ 156 157 158 #ifdef CONFIG_OMAP1510 159 #define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */ 160 #endif 161 162 /* useful defaults for LCR */ 163 #define UART_LCR_8N1 0x03 164 165 void NS16550_init (NS16550_t com_port, int baud_divisor); 166 void NS16550_putc (NS16550_t com_port, char c); 167 char NS16550_getc (NS16550_t com_port); 168 int NS16550_tstc (NS16550_t com_port); 169 void NS16550_reinit (NS16550_t com_port, int baud_divisor); 170