1 /* 2 * NS16550 Serial Port 3 * originally from linux source (arch/ppc/boot/ns16550.h) 4 * 5 * Cleanup and unification 6 * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH 7 * 8 * modified slightly to 9 * have addresses as offsets from CONFIG_SYS_ISA_BASE 10 * added a few more definitions 11 * added prototypes for ns16550.c 12 * reduced no of com ports to 2 13 * modifications (c) Rob Taylor, Flying Pig Systems. 2000. 14 * 15 * added support for port on 64-bit bus 16 * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems 17 */ 18 19 /* 20 * Note that the following macro magic uses the fact that the compiler 21 * will not allocate storage for arrays of size 0 22 */ 23 24 #if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0) 25 #error "Please define NS16550 registers size." 26 #elif (CONFIG_SYS_NS16550_REG_SIZE > 0) 27 #define UART_REG(x) \ 28 unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \ 29 unsigned char x; 30 #elif (CONFIG_SYS_NS16550_REG_SIZE < 0) 31 #define UART_REG(x) \ 32 unsigned char x; \ 33 unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1]; 34 #endif 35 36 struct NS16550 { 37 UART_REG(rbr); /* 0 */ 38 UART_REG(ier); /* 1 */ 39 UART_REG(fcr); /* 2 */ 40 UART_REG(lcr); /* 3 */ 41 UART_REG(mcr); /* 4 */ 42 UART_REG(lsr); /* 5 */ 43 UART_REG(msr); /* 6 */ 44 UART_REG(spr); /* 7 */ 45 UART_REG(mdr1); /* 8 */ 46 UART_REG(reg9); /* 9 */ 47 UART_REG(regA); /* A */ 48 UART_REG(regB); /* B */ 49 UART_REG(regC); /* C */ 50 UART_REG(regD); /* D */ 51 UART_REG(regE); /* E */ 52 UART_REG(uasr); /* F */ 53 UART_REG(scr); /* 10*/ 54 UART_REG(ssr); /* 11*/ 55 UART_REG(reg12); /* 12*/ 56 UART_REG(osc_12m_sel); /* 13*/ 57 }; 58 59 #define thr rbr 60 #define iir fcr 61 #define dll rbr 62 #define dlm ier 63 64 typedef volatile struct NS16550 *NS16550_t; 65 66 /* 67 * These are the definitions for the FIFO Control Register 68 */ 69 #define UART_FCR_FIFO_EN 0x01 /* Fifo enable */ 70 #define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ 71 #define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ 72 #define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ 73 #define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ 74 #define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ 75 #define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ 76 #define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ 77 #define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ 78 79 #define UART_FCR_RXSR 0x02 /* Receiver soft reset */ 80 #define UART_FCR_TXSR 0x04 /* Transmitter soft reset */ 81 82 /* 83 * These are the definitions for the Modem Control Register 84 */ 85 #define UART_MCR_DTR 0x01 /* DTR */ 86 #define UART_MCR_RTS 0x02 /* RTS */ 87 #define UART_MCR_OUT1 0x04 /* Out 1 */ 88 #define UART_MCR_OUT2 0x08 /* Out 2 */ 89 #define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ 90 91 #define UART_MCR_DMA_EN 0x04 92 #define UART_MCR_TX_DFR 0x08 93 94 /* 95 * These are the definitions for the Line Control Register 96 * 97 * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting 98 * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. 99 */ 100 #define UART_LCR_WLS_MSK 0x03 /* character length select mask */ 101 #define UART_LCR_WLS_5 0x00 /* 5 bit character length */ 102 #define UART_LCR_WLS_6 0x01 /* 6 bit character length */ 103 #define UART_LCR_WLS_7 0x02 /* 7 bit character length */ 104 #define UART_LCR_WLS_8 0x03 /* 8 bit character length */ 105 #define UART_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */ 106 #define UART_LCR_PEN 0x08 /* Parity eneble */ 107 #define UART_LCR_EPS 0x10 /* Even Parity Select */ 108 #define UART_LCR_STKP 0x20 /* Stick Parity */ 109 #define UART_LCR_SBRK 0x40 /* Set Break */ 110 #define UART_LCR_BKSE 0x80 /* Bank select enable */ 111 #define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ 112 113 /* 114 * These are the definitions for the Line Status Register 115 */ 116 #define UART_LSR_DR 0x01 /* Data ready */ 117 #define UART_LSR_OE 0x02 /* Overrun */ 118 #define UART_LSR_PE 0x04 /* Parity error */ 119 #define UART_LSR_FE 0x08 /* Framing error */ 120 #define UART_LSR_BI 0x10 /* Break */ 121 #define UART_LSR_THRE 0x20 /* Xmit holding register empty */ 122 #define UART_LSR_TEMT 0x40 /* Xmitter empty */ 123 #define UART_LSR_ERR 0x80 /* Error */ 124 125 #define UART_MSR_DCD 0x80 /* Data Carrier Detect */ 126 #define UART_MSR_RI 0x40 /* Ring Indicator */ 127 #define UART_MSR_DSR 0x20 /* Data Set Ready */ 128 #define UART_MSR_CTS 0x10 /* Clear to Send */ 129 #define UART_MSR_DDCD 0x08 /* Delta DCD */ 130 #define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ 131 #define UART_MSR_DDSR 0x02 /* Delta DSR */ 132 #define UART_MSR_DCTS 0x01 /* Delta CTS */ 133 134 /* 135 * These are the definitions for the Interrupt Identification Register 136 */ 137 #define UART_IIR_NO_INT 0x01 /* No interrupts pending */ 138 #define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ 139 140 #define UART_IIR_MSI 0x00 /* Modem status interrupt */ 141 #define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ 142 #define UART_IIR_RDI 0x04 /* Receiver data interrupt */ 143 #define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ 144 145 /* 146 * These are the definitions for the Interrupt Enable Register 147 */ 148 #define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ 149 #define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ 150 #define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ 151 #define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ 152 153 154 #ifdef CONFIG_OMAP1510 155 #define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */ 156 #endif 157 158 /* useful defaults for LCR */ 159 #define UART_LCR_8N1 0x03 160 161 void NS16550_init (NS16550_t com_port, int baud_divisor); 162 void NS16550_putc (NS16550_t com_port, char c); 163 char NS16550_getc (NS16550_t com_port); 164 int NS16550_tstc (NS16550_t com_port); 165 void NS16550_reinit (NS16550_t com_port, int baud_divisor); 166