1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* 3 * LiMon Monitor (LiMon) - Network. 4 * 5 * Copyright 1994 - 2000 Neil Russell. 6 * (See License) 7 * 8 * History 9 * 9/16/00 bor adapted to TQM823L/STK8xxL board, RARP/TFTP boot added 10 */ 11 12 #ifndef __NET_H__ 13 #define __NET_H__ 14 15 #include <asm/cache.h> 16 #include <asm/byteorder.h> /* for nton* / ntoh* stuff */ 17 #include <linux/if_ether.h> 18 19 #define DEBUG_LL_STATE 0 /* Link local state machine changes */ 20 #define DEBUG_DEV_PKT 0 /* Packets or info directed to the device */ 21 #define DEBUG_NET_PKT 0 /* Packets on info on the network at large */ 22 #define DEBUG_INT_STATE 0 /* Internal network state changes */ 23 24 /* 25 * The number of receive packet buffers, and the required packet buffer 26 * alignment in memory. 27 * 28 */ 29 30 #ifdef CONFIG_SYS_RX_ETH_BUFFER 31 # define PKTBUFSRX CONFIG_SYS_RX_ETH_BUFFER 32 #else 33 # define PKTBUFSRX 4 34 #endif 35 36 #define PKTALIGN ARCH_DMA_MINALIGN 37 38 /* ARP hardware address length */ 39 #define ARP_HLEN 6 40 /* 41 * The size of a MAC address in string form, each digit requires two chars 42 * and five separator characters to form '00:00:00:00:00:00'. 43 */ 44 #define ARP_HLEN_ASCII (ARP_HLEN * 2) + (ARP_HLEN - 1) 45 46 /* IPv4 addresses are always 32 bits in size */ 47 struct in_addr { 48 __be32 s_addr; 49 }; 50 51 /** 52 * An incoming packet handler. 53 * @param pkt pointer to the application packet 54 * @param dport destination UDP port 55 * @param sip source IP address 56 * @param sport source UDP port 57 * @param len packet length 58 */ 59 typedef void rxhand_f(uchar *pkt, unsigned dport, 60 struct in_addr sip, unsigned sport, 61 unsigned len); 62 63 /** 64 * An incoming ICMP packet handler. 65 * @param type ICMP type 66 * @param code ICMP code 67 * @param dport destination UDP port 68 * @param sip source IP address 69 * @param sport source UDP port 70 * @param pkt pointer to the ICMP packet data 71 * @param len packet length 72 */ 73 typedef void rxhand_icmp_f(unsigned type, unsigned code, unsigned dport, 74 struct in_addr sip, unsigned sport, uchar *pkt, unsigned len); 75 76 /* 77 * A timeout handler. Called after time interval has expired. 78 */ 79 typedef void thand_f(void); 80 81 enum eth_state_t { 82 ETH_STATE_INIT, 83 ETH_STATE_PASSIVE, 84 ETH_STATE_ACTIVE 85 }; 86 87 #ifdef CONFIG_DM_ETH 88 /** 89 * struct eth_pdata - Platform data for Ethernet MAC controllers 90 * 91 * @iobase: The base address of the hardware registers 92 * @enetaddr: The Ethernet MAC address that is loaded from EEPROM or env 93 * @phy_interface: PHY interface to use - see PHY_INTERFACE_MODE_... 94 * @max_speed: Maximum speed of Ethernet connection supported by MAC 95 */ 96 struct eth_pdata { 97 phys_addr_t iobase; 98 unsigned char enetaddr[ARP_HLEN]; 99 int phy_interface; 100 int max_speed; 101 }; 102 103 enum eth_recv_flags { 104 /* 105 * Check hardware device for new packets (otherwise only return those 106 * which are already in the memory buffer ready to process) 107 */ 108 ETH_RECV_CHECK_DEVICE = 1 << 0, 109 }; 110 111 /** 112 * struct eth_ops - functions of Ethernet MAC controllers 113 * 114 * start: Prepare the hardware to send and receive packets 115 * send: Send the bytes passed in "packet" as a packet on the wire 116 * recv: Check if the hardware received a packet. If so, set the pointer to the 117 * packet buffer in the packetp parameter. If not, return an error or 0 to 118 * indicate that the hardware receive FIFO is empty. If 0 is returned, the 119 * network stack will not process the empty packet, but free_pkt() will be 120 * called if supplied 121 * free_pkt: Give the driver an opportunity to manage its packet buffer memory 122 * when the network stack is finished processing it. This will only be 123 * called when no error was returned from recv - optional 124 * stop: Stop the hardware from looking for packets - may be called even if 125 * state == PASSIVE 126 * mcast: Join or leave a multicast group (for TFTP) - optional 127 * write_hwaddr: Write a MAC address to the hardware (used to pass it to Linux 128 * on some platforms like ARM). This function expects the 129 * eth_pdata::enetaddr field to be populated. The method can 130 * return -ENOSYS to indicate that this is not implemented for 131 this hardware - optional. 132 * read_rom_hwaddr: Some devices have a backup of the MAC address stored in a 133 * ROM on the board. This is how the driver should expose it 134 * to the network stack. This function should fill in the 135 * eth_pdata::enetaddr field - optional 136 */ 137 struct eth_ops { 138 int (*start)(struct udevice *dev); 139 int (*send)(struct udevice *dev, void *packet, int length); 140 int (*recv)(struct udevice *dev, int flags, uchar **packetp); 141 int (*free_pkt)(struct udevice *dev, uchar *packet, int length); 142 void (*stop)(struct udevice *dev); 143 int (*mcast)(struct udevice *dev, const u8 *enetaddr, int join); 144 int (*write_hwaddr)(struct udevice *dev); 145 int (*read_rom_hwaddr)(struct udevice *dev); 146 }; 147 148 #define eth_get_ops(dev) ((struct eth_ops *)(dev)->driver->ops) 149 150 struct udevice *eth_get_dev(void); /* get the current device */ 151 /* 152 * The devname can be either an exact name given by the driver or device tree 153 * or it can be an alias of the form "eth%d" 154 */ 155 struct udevice *eth_get_dev_by_name(const char *devname); 156 unsigned char *eth_get_ethaddr(void); /* get the current device MAC */ 157 158 /* Used only when NetConsole is enabled */ 159 int eth_is_active(struct udevice *dev); /* Test device for active state */ 160 int eth_init_state_only(void); /* Set active state */ 161 void eth_halt_state_only(void); /* Set passive state */ 162 #endif 163 164 #ifndef CONFIG_DM_ETH 165 struct eth_device { 166 #define ETH_NAME_LEN 20 167 char name[ETH_NAME_LEN]; 168 unsigned char enetaddr[ARP_HLEN]; 169 phys_addr_t iobase; 170 int state; 171 172 int (*init)(struct eth_device *, bd_t *); 173 int (*send)(struct eth_device *, void *packet, int length); 174 int (*recv)(struct eth_device *); 175 void (*halt)(struct eth_device *); 176 int (*mcast)(struct eth_device *, const u8 *enetaddr, int join); 177 int (*write_hwaddr)(struct eth_device *); 178 struct eth_device *next; 179 int index; 180 void *priv; 181 }; 182 183 int eth_register(struct eth_device *dev);/* Register network device */ 184 int eth_unregister(struct eth_device *dev);/* Remove network device */ 185 186 extern struct eth_device *eth_current; 187 188 static __always_inline struct eth_device *eth_get_dev(void) 189 { 190 return eth_current; 191 } 192 struct eth_device *eth_get_dev_by_name(const char *devname); 193 struct eth_device *eth_get_dev_by_index(int index); /* get dev @ index */ 194 195 /* get the current device MAC */ 196 static inline unsigned char *eth_get_ethaddr(void) 197 { 198 if (eth_current) 199 return eth_current->enetaddr; 200 return NULL; 201 } 202 203 /* Used only when NetConsole is enabled */ 204 int eth_is_active(struct eth_device *dev); /* Test device for active state */ 205 /* Set active state */ 206 static __always_inline int eth_init_state_only(void) 207 { 208 eth_get_dev()->state = ETH_STATE_ACTIVE; 209 210 return 0; 211 } 212 /* Set passive state */ 213 static __always_inline void eth_halt_state_only(void) 214 { 215 eth_get_dev()->state = ETH_STATE_PASSIVE; 216 } 217 218 /* 219 * Set the hardware address for an ethernet interface based on 'eth%daddr' 220 * environment variable (or just 'ethaddr' if eth_number is 0). 221 * Args: 222 * base_name - base name for device (normally "eth") 223 * eth_number - value of %d (0 for first device of this type) 224 * Returns: 225 * 0 is success, non-zero is error status from driver. 226 */ 227 int eth_write_hwaddr(struct eth_device *dev, const char *base_name, 228 int eth_number); 229 230 int usb_eth_initialize(bd_t *bi); 231 #endif 232 233 int eth_initialize(void); /* Initialize network subsystem */ 234 void eth_try_another(int first_restart); /* Change the device */ 235 void eth_set_current(void); /* set nterface to ethcur var */ 236 237 int eth_get_dev_index(void); /* get the device index */ 238 239 /** 240 * eth_env_set_enetaddr_by_index() - set the MAC address environment variable 241 * 242 * This sets up an environment variable with the given MAC address (@enetaddr). 243 * The environment variable to be set is defined by <@base_name><@index>addr. 244 * If @index is 0 it is omitted. For common Ethernet this means ethaddr, 245 * eth1addr, etc. 246 * 247 * @base_name: Base name for variable, typically "eth" 248 * @index: Index of interface being updated (>=0) 249 * @enetaddr: Pointer to MAC address to put into the variable 250 * @return 0 if OK, other value on error 251 */ 252 int eth_env_set_enetaddr_by_index(const char *base_name, int index, 253 uchar *enetaddr); 254 255 256 /* 257 * Initialize USB ethernet device with CONFIG_DM_ETH 258 * Returns: 259 * 0 is success, non-zero is error status. 260 */ 261 int usb_ether_init(void); 262 263 /* 264 * Get the hardware address for an ethernet interface . 265 * Args: 266 * base_name - base name for device (normally "eth") 267 * index - device index number (0 for first) 268 * enetaddr - returns 6 byte hardware address 269 * Returns: 270 * Return true if the address is valid. 271 */ 272 int eth_env_get_enetaddr_by_index(const char *base_name, int index, 273 uchar *enetaddr); 274 275 int eth_init(void); /* Initialize the device */ 276 int eth_send(void *packet, int length); /* Send a packet */ 277 278 #if defined(CONFIG_API) || defined(CONFIG_EFI_LOADER) 279 int eth_receive(void *packet, int length); /* Receive a packet*/ 280 extern void (*push_packet)(void *packet, int length); 281 #endif 282 int eth_rx(void); /* Check for received packets */ 283 void eth_halt(void); /* stop SCC */ 284 const char *eth_get_name(void); /* get name of current device */ 285 int eth_mcast_join(struct in_addr mcast_addr, int join); 286 287 /**********************************************************************/ 288 /* 289 * Protocol headers. 290 */ 291 292 /* 293 * Ethernet header 294 */ 295 296 struct ethernet_hdr { 297 u8 et_dest[ARP_HLEN]; /* Destination node */ 298 u8 et_src[ARP_HLEN]; /* Source node */ 299 u16 et_protlen; /* Protocol or length */ 300 } __attribute__((packed)); 301 302 /* Ethernet header size */ 303 #define ETHER_HDR_SIZE (sizeof(struct ethernet_hdr)) 304 305 #define ETH_FCS_LEN 4 /* Octets in the FCS */ 306 307 struct e802_hdr { 308 u8 et_dest[ARP_HLEN]; /* Destination node */ 309 u8 et_src[ARP_HLEN]; /* Source node */ 310 u16 et_protlen; /* Protocol or length */ 311 u8 et_dsap; /* 802 DSAP */ 312 u8 et_ssap; /* 802 SSAP */ 313 u8 et_ctl; /* 802 control */ 314 u8 et_snap1; /* SNAP */ 315 u8 et_snap2; 316 u8 et_snap3; 317 u16 et_prot; /* 802 protocol */ 318 } __attribute__((packed)); 319 320 /* 802 + SNAP + ethernet header size */ 321 #define E802_HDR_SIZE (sizeof(struct e802_hdr)) 322 323 /* 324 * Virtual LAN Ethernet header 325 */ 326 struct vlan_ethernet_hdr { 327 u8 vet_dest[ARP_HLEN]; /* Destination node */ 328 u8 vet_src[ARP_HLEN]; /* Source node */ 329 u16 vet_vlan_type; /* PROT_VLAN */ 330 u16 vet_tag; /* TAG of VLAN */ 331 u16 vet_type; /* protocol type */ 332 } __attribute__((packed)); 333 334 /* VLAN Ethernet header size */ 335 #define VLAN_ETHER_HDR_SIZE (sizeof(struct vlan_ethernet_hdr)) 336 337 #define PROT_IP 0x0800 /* IP protocol */ 338 #define PROT_ARP 0x0806 /* IP ARP protocol */ 339 #define PROT_WOL 0x0842 /* ether-wake WoL protocol */ 340 #define PROT_RARP 0x8035 /* IP ARP protocol */ 341 #define PROT_VLAN 0x8100 /* IEEE 802.1q protocol */ 342 #define PROT_IPV6 0x86dd /* IPv6 over bluebook */ 343 #define PROT_PPP_SES 0x8864 /* PPPoE session messages */ 344 #define PROT_NCSI 0x88f8 /* NC-SI control packets */ 345 346 #define IPPROTO_ICMP 1 /* Internet Control Message Protocol */ 347 #define IPPROTO_UDP 17 /* User Datagram Protocol */ 348 349 /* 350 * Internet Protocol (IP) header. 351 */ 352 struct ip_hdr { 353 u8 ip_hl_v; /* header length and version */ 354 u8 ip_tos; /* type of service */ 355 u16 ip_len; /* total length */ 356 u16 ip_id; /* identification */ 357 u16 ip_off; /* fragment offset field */ 358 u8 ip_ttl; /* time to live */ 359 u8 ip_p; /* protocol */ 360 u16 ip_sum; /* checksum */ 361 struct in_addr ip_src; /* Source IP address */ 362 struct in_addr ip_dst; /* Destination IP address */ 363 } __attribute__((packed)); 364 365 #define IP_OFFS 0x1fff /* ip offset *= 8 */ 366 #define IP_FLAGS 0xe000 /* first 3 bits */ 367 #define IP_FLAGS_RES 0x8000 /* reserved */ 368 #define IP_FLAGS_DFRAG 0x4000 /* don't fragments */ 369 #define IP_FLAGS_MFRAG 0x2000 /* more fragments */ 370 371 #define IP_HDR_SIZE (sizeof(struct ip_hdr)) 372 373 /* 374 * Internet Protocol (IP) + UDP header. 375 */ 376 struct ip_udp_hdr { 377 u8 ip_hl_v; /* header length and version */ 378 u8 ip_tos; /* type of service */ 379 u16 ip_len; /* total length */ 380 u16 ip_id; /* identification */ 381 u16 ip_off; /* fragment offset field */ 382 u8 ip_ttl; /* time to live */ 383 u8 ip_p; /* protocol */ 384 u16 ip_sum; /* checksum */ 385 struct in_addr ip_src; /* Source IP address */ 386 struct in_addr ip_dst; /* Destination IP address */ 387 u16 udp_src; /* UDP source port */ 388 u16 udp_dst; /* UDP destination port */ 389 u16 udp_len; /* Length of UDP packet */ 390 u16 udp_xsum; /* Checksum */ 391 } __attribute__((packed)); 392 393 #define IP_UDP_HDR_SIZE (sizeof(struct ip_udp_hdr)) 394 #define UDP_HDR_SIZE (IP_UDP_HDR_SIZE - IP_HDR_SIZE) 395 396 /* 397 * Address Resolution Protocol (ARP) header. 398 */ 399 struct arp_hdr { 400 u16 ar_hrd; /* Format of hardware address */ 401 # define ARP_ETHER 1 /* Ethernet hardware address */ 402 u16 ar_pro; /* Format of protocol address */ 403 u8 ar_hln; /* Length of hardware address */ 404 u8 ar_pln; /* Length of protocol address */ 405 # define ARP_PLEN 4 406 u16 ar_op; /* Operation */ 407 # define ARPOP_REQUEST 1 /* Request to resolve address */ 408 # define ARPOP_REPLY 2 /* Response to previous request */ 409 410 # define RARPOP_REQUEST 3 /* Request to resolve address */ 411 # define RARPOP_REPLY 4 /* Response to previous request */ 412 413 /* 414 * The remaining fields are variable in size, according to 415 * the sizes above, and are defined as appropriate for 416 * specific hardware/protocol combinations. 417 */ 418 u8 ar_data[0]; 419 #define ar_sha ar_data[0] 420 #define ar_spa ar_data[ARP_HLEN] 421 #define ar_tha ar_data[ARP_HLEN + ARP_PLEN] 422 #define ar_tpa ar_data[ARP_HLEN + ARP_PLEN + ARP_HLEN] 423 #if 0 424 u8 ar_sha[]; /* Sender hardware address */ 425 u8 ar_spa[]; /* Sender protocol address */ 426 u8 ar_tha[]; /* Target hardware address */ 427 u8 ar_tpa[]; /* Target protocol address */ 428 #endif /* 0 */ 429 } __attribute__((packed)); 430 431 #define ARP_HDR_SIZE (8+20) /* Size assuming ethernet */ 432 433 /* 434 * ICMP stuff (just enough to handle (host) redirect messages) 435 */ 436 #define ICMP_ECHO_REPLY 0 /* Echo reply */ 437 #define ICMP_NOT_REACH 3 /* Detination unreachable */ 438 #define ICMP_REDIRECT 5 /* Redirect (change route) */ 439 #define ICMP_ECHO_REQUEST 8 /* Echo request */ 440 441 /* Codes for REDIRECT. */ 442 #define ICMP_REDIR_NET 0 /* Redirect Net */ 443 #define ICMP_REDIR_HOST 1 /* Redirect Host */ 444 445 /* Codes for NOT_REACH */ 446 #define ICMP_NOT_REACH_PORT 3 /* Port unreachable */ 447 448 struct icmp_hdr { 449 u8 type; 450 u8 code; 451 u16 checksum; 452 union { 453 struct { 454 u16 id; 455 u16 sequence; 456 } echo; 457 u32 gateway; 458 struct { 459 u16 unused; 460 u16 mtu; 461 } frag; 462 u8 data[0]; 463 } un; 464 } __attribute__((packed)); 465 466 #define ICMP_HDR_SIZE (sizeof(struct icmp_hdr)) 467 #define IP_ICMP_HDR_SIZE (IP_HDR_SIZE + ICMP_HDR_SIZE) 468 469 /* 470 * Maximum packet size; used to allocate packet storage. Use 471 * the maxium Ethernet frame size as specified by the Ethernet 472 * standard including the 802.1Q tag (VLAN tagging). 473 * maximum packet size = 1522 474 * maximum packet size and multiple of 32 bytes = 1536 475 */ 476 #define PKTSIZE 1522 477 #define PKTSIZE_ALIGN 1536 478 479 /* 480 * Maximum receive ring size; that is, the number of packets 481 * we can buffer before overflow happens. Basically, this just 482 * needs to be enough to prevent a packet being discarded while 483 * we are processing the previous one. 484 */ 485 #define RINGSZ 4 486 #define RINGSZ_LOG2 2 487 488 /**********************************************************************/ 489 /* 490 * Globals. 491 * 492 * Note: 493 * 494 * All variables of type struct in_addr are stored in NETWORK byte order 495 * (big endian). 496 */ 497 498 /* net.c */ 499 /** BOOTP EXTENTIONS **/ 500 extern struct in_addr net_gateway; /* Our gateway IP address */ 501 extern struct in_addr net_netmask; /* Our subnet mask (0 = unknown) */ 502 /* Our Domain Name Server (0 = unknown) */ 503 extern struct in_addr net_dns_server; 504 #if defined(CONFIG_BOOTP_DNS2) 505 /* Our 2nd Domain Name Server (0 = unknown) */ 506 extern struct in_addr net_dns_server2; 507 #endif 508 extern char net_nis_domain[32]; /* Our IS domain */ 509 extern char net_hostname[32]; /* Our hostname */ 510 extern char net_root_path[64]; /* Our root path */ 511 /** END OF BOOTP EXTENTIONS **/ 512 extern u8 net_ethaddr[ARP_HLEN]; /* Our ethernet address */ 513 extern u8 net_server_ethaddr[ARP_HLEN]; /* Boot server enet address */ 514 extern struct in_addr net_ip; /* Our IP addr (0 = unknown) */ 515 extern struct in_addr net_server_ip; /* Server IP addr (0 = unknown) */ 516 extern uchar *net_tx_packet; /* THE transmit packet */ 517 extern uchar *net_rx_packets[PKTBUFSRX]; /* Receive packets */ 518 extern uchar *net_rx_packet; /* Current receive packet */ 519 extern int net_rx_packet_len; /* Current rx packet length */ 520 extern const u8 net_bcast_ethaddr[ARP_HLEN]; /* Ethernet broadcast address */ 521 extern const u8 net_null_ethaddr[ARP_HLEN]; 522 523 #define VLAN_NONE 4095 /* untagged */ 524 #define VLAN_IDMASK 0x0fff /* mask of valid vlan id */ 525 extern ushort net_our_vlan; /* Our VLAN */ 526 extern ushort net_native_vlan; /* Our Native VLAN */ 527 528 extern int net_restart_wrap; /* Tried all network devices */ 529 530 enum proto_t { 531 BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP, 532 TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL, NCSI 533 }; 534 535 extern char net_boot_file_name[1024];/* Boot File name */ 536 /* Indicates whether the file name was specified on the command line */ 537 extern bool net_boot_file_name_explicit; 538 /* The actual transferred size of the bootfile (in bytes) */ 539 extern u32 net_boot_file_size; 540 /* Boot file size in blocks as reported by the DHCP server */ 541 extern u32 net_boot_file_expected_size_in_blocks; 542 543 #if defined(CONFIG_CMD_DNS) 544 extern char *net_dns_resolve; /* The host to resolve */ 545 extern char *net_dns_env_var; /* the env var to put the ip into */ 546 #endif 547 548 #if defined(CONFIG_CMD_PING) 549 extern struct in_addr net_ping_ip; /* the ip address to ping */ 550 #endif 551 552 #if defined(CONFIG_CMD_CDP) 553 /* when CDP completes these hold the return values */ 554 extern ushort cdp_native_vlan; /* CDP returned native VLAN */ 555 extern ushort cdp_appliance_vlan; /* CDP returned appliance VLAN */ 556 557 /* 558 * Check for a CDP packet by examining the received MAC address field 559 */ 560 static inline int is_cdp_packet(const uchar *ethaddr) 561 { 562 extern const u8 net_cdp_ethaddr[ARP_HLEN]; 563 564 return memcmp(ethaddr, net_cdp_ethaddr, ARP_HLEN) == 0; 565 } 566 #endif 567 568 #if defined(CONFIG_CMD_SNTP) 569 extern struct in_addr net_ntp_server; /* the ip address to NTP */ 570 extern int net_ntp_time_offset; /* offset time from UTC */ 571 #endif 572 573 /* Initialize the network adapter */ 574 void net_init(void); 575 int net_loop(enum proto_t); 576 577 /* Load failed. Start again. */ 578 int net_start_again(void); 579 580 /* Get size of the ethernet header when we send */ 581 int net_eth_hdr_size(void); 582 583 /* Set ethernet header; returns the size of the header */ 584 int net_set_ether(uchar *xet, const uchar *dest_ethaddr, uint prot); 585 int net_update_ether(struct ethernet_hdr *et, uchar *addr, uint prot); 586 587 /* Set IP header */ 588 void net_set_ip_header(uchar *pkt, struct in_addr dest, struct in_addr source, 589 u16 pkt_len, u8 proto); 590 void net_set_udp_header(uchar *pkt, struct in_addr dest, int dport, 591 int sport, int len); 592 593 /** 594 * compute_ip_checksum() - Compute IP checksum 595 * 596 * @addr: Address to check (must be 16-bit aligned) 597 * @nbytes: Number of bytes to check (normally a multiple of 2) 598 * @return 16-bit IP checksum 599 */ 600 unsigned compute_ip_checksum(const void *addr, unsigned nbytes); 601 602 /** 603 * add_ip_checksums() - add two IP checksums 604 * 605 * @offset: Offset of first sum (if odd we do a byte-swap) 606 * @sum: First checksum 607 * @new_sum: New checksum to add 608 * @return updated 16-bit IP checksum 609 */ 610 unsigned add_ip_checksums(unsigned offset, unsigned sum, unsigned new_sum); 611 612 /** 613 * ip_checksum_ok() - check if a checksum is correct 614 * 615 * This works by making sure the checksum sums to 0 616 * 617 * @addr: Address to check (must be 16-bit aligned) 618 * @nbytes: Number of bytes to check (normally a multiple of 2) 619 * @return true if the checksum matches, false if not 620 */ 621 int ip_checksum_ok(const void *addr, unsigned nbytes); 622 623 /* Callbacks */ 624 rxhand_f *net_get_udp_handler(void); /* Get UDP RX packet handler */ 625 void net_set_udp_handler(rxhand_f *); /* Set UDP RX packet handler */ 626 rxhand_f *net_get_arp_handler(void); /* Get ARP RX packet handler */ 627 void net_set_arp_handler(rxhand_f *); /* Set ARP RX packet handler */ 628 bool arp_is_waiting(void); /* Waiting for ARP reply? */ 629 void net_set_icmp_handler(rxhand_icmp_f *f); /* Set ICMP RX handler */ 630 void net_set_timeout_handler(ulong, thand_f *);/* Set timeout handler */ 631 632 /* Network loop state */ 633 enum net_loop_state { 634 NETLOOP_CONTINUE, 635 NETLOOP_RESTART, 636 NETLOOP_SUCCESS, 637 NETLOOP_FAIL 638 }; 639 extern enum net_loop_state net_state; 640 641 static inline void net_set_state(enum net_loop_state state) 642 { 643 debug_cond(DEBUG_INT_STATE, "--- NetState set to %d\n", state); 644 net_state = state; 645 } 646 647 /* 648 * net_get_async_tx_pkt_buf - Get a packet buffer that is not in use for 649 * sending an asynchronous reply 650 * 651 * returns - ptr to packet buffer 652 */ 653 uchar * net_get_async_tx_pkt_buf(void); 654 655 /* Transmit a packet */ 656 static inline void net_send_packet(uchar *pkt, int len) 657 { 658 /* Currently no way to return errors from eth_send() */ 659 (void) eth_send(pkt, len); 660 } 661 662 /* 663 * Transmit "net_tx_packet" as UDP packet, performing ARP request if needed 664 * (ether will be populated) 665 * 666 * @param ether Raw packet buffer 667 * @param dest IP address to send the datagram to 668 * @param dport Destination UDP port 669 * @param sport Source UDP port 670 * @param payload_len Length of data after the UDP header 671 */ 672 int net_send_ip_packet(uchar *ether, struct in_addr dest, int dport, int sport, 673 int payload_len, int proto, u8 action, u32 tcp_seq_num, 674 u32 tcp_ack_num); 675 int net_send_udp_packet(uchar *ether, struct in_addr dest, int dport, 676 int sport, int payload_len); 677 678 /* Processes a received packet */ 679 void net_process_received_packet(uchar *in_packet, int len); 680 681 #if defined(CONFIG_NETCONSOLE) && !defined(CONFIG_SPL_BUILD) 682 void nc_start(void); 683 int nc_input_packet(uchar *pkt, struct in_addr src_ip, unsigned dest_port, 684 unsigned src_port, unsigned len); 685 #endif 686 687 static __always_inline int eth_is_on_demand_init(void) 688 { 689 #if defined(CONFIG_NETCONSOLE) && !defined(CONFIG_SPL_BUILD) 690 extern enum proto_t net_loop_last_protocol; 691 692 return net_loop_last_protocol != NETCONS; 693 #else 694 return 1; 695 #endif 696 } 697 698 static inline void eth_set_last_protocol(int protocol) 699 { 700 #if defined(CONFIG_NETCONSOLE) && !defined(CONFIG_SPL_BUILD) 701 extern enum proto_t net_loop_last_protocol; 702 703 net_loop_last_protocol = protocol; 704 #endif 705 } 706 707 /* 708 * Check if autoload is enabled. If so, use either NFS or TFTP to download 709 * the boot file. 710 */ 711 void net_auto_load(void); 712 713 /* 714 * The following functions are a bit ugly, but necessary to deal with 715 * alignment restrictions on ARM. 716 * 717 * We're using inline functions, which had the smallest memory 718 * footprint in our tests. 719 */ 720 /* return IP *in network byteorder* */ 721 static inline struct in_addr net_read_ip(void *from) 722 { 723 struct in_addr ip; 724 725 memcpy((void *)&ip, (void *)from, sizeof(ip)); 726 return ip; 727 } 728 729 /* return ulong *in network byteorder* */ 730 static inline u32 net_read_u32(u32 *from) 731 { 732 u32 l; 733 734 memcpy((void *)&l, (void *)from, sizeof(l)); 735 return l; 736 } 737 738 /* write IP *in network byteorder* */ 739 static inline void net_write_ip(void *to, struct in_addr ip) 740 { 741 memcpy(to, (void *)&ip, sizeof(ip)); 742 } 743 744 /* copy IP */ 745 static inline void net_copy_ip(void *to, void *from) 746 { 747 memcpy((void *)to, from, sizeof(struct in_addr)); 748 } 749 750 /* copy ulong */ 751 static inline void net_copy_u32(u32 *to, u32 *from) 752 { 753 memcpy((void *)to, (void *)from, sizeof(u32)); 754 } 755 756 /** 757 * is_zero_ethaddr - Determine if give Ethernet address is all zeros. 758 * @addr: Pointer to a six-byte array containing the Ethernet address 759 * 760 * Return true if the address is all zeroes. 761 */ 762 static inline int is_zero_ethaddr(const u8 *addr) 763 { 764 return !(addr[0] | addr[1] | addr[2] | addr[3] | addr[4] | addr[5]); 765 } 766 767 /** 768 * is_multicast_ethaddr - Determine if the Ethernet address is a multicast. 769 * @addr: Pointer to a six-byte array containing the Ethernet address 770 * 771 * Return true if the address is a multicast address. 772 * By definition the broadcast address is also a multicast address. 773 */ 774 static inline int is_multicast_ethaddr(const u8 *addr) 775 { 776 return 0x01 & addr[0]; 777 } 778 779 /* 780 * is_broadcast_ethaddr - Determine if the Ethernet address is broadcast 781 * @addr: Pointer to a six-byte array containing the Ethernet address 782 * 783 * Return true if the address is the broadcast address. 784 */ 785 static inline int is_broadcast_ethaddr(const u8 *addr) 786 { 787 return (addr[0] & addr[1] & addr[2] & addr[3] & addr[4] & addr[5]) == 788 0xff; 789 } 790 791 /* 792 * is_valid_ethaddr - Determine if the given Ethernet address is valid 793 * @addr: Pointer to a six-byte array containing the Ethernet address 794 * 795 * Check that the Ethernet address (MAC) is not 00:00:00:00:00:00, is not 796 * a multicast address, and is not FF:FF:FF:FF:FF:FF. 797 * 798 * Return true if the address is valid. 799 */ 800 static inline int is_valid_ethaddr(const u8 *addr) 801 { 802 /* FF:FF:FF:FF:FF:FF is a multicast address so we don't need to 803 * explicitly check for it here. */ 804 return !is_multicast_ethaddr(addr) && !is_zero_ethaddr(addr); 805 } 806 807 /** 808 * net_random_ethaddr - Generate software assigned random Ethernet address 809 * @addr: Pointer to a six-byte array containing the Ethernet address 810 * 811 * Generate a random Ethernet address (MAC) that is not multicast 812 * and has the local assigned bit set. 813 */ 814 static inline void net_random_ethaddr(uchar *addr) 815 { 816 int i; 817 unsigned int seed = get_timer(0); 818 819 for (i = 0; i < 6; i++) 820 addr[i] = rand_r(&seed); 821 822 addr[0] &= 0xfe; /* clear multicast bit */ 823 addr[0] |= 0x02; /* set local assignment bit (IEEE802) */ 824 } 825 826 /* Convert an IP address to a string */ 827 void ip_to_string(struct in_addr x, char *s); 828 829 /* Convert a string to ip address */ 830 struct in_addr string_to_ip(const char *s); 831 832 /* Convert a VLAN id to a string */ 833 void vlan_to_string(ushort x, char *s); 834 835 /* Convert a string to a vlan id */ 836 ushort string_to_vlan(const char *s); 837 838 /* read a VLAN id from an environment variable */ 839 ushort env_get_vlan(char *); 840 841 /* copy a filename (allow for "..." notation, limit length) */ 842 void copy_filename(char *dst, const char *src, int size); 843 844 /* check if serverip is specified in filename from the command line */ 845 int is_serverip_in_cmd(void); 846 847 /** 848 * net_parse_bootfile - Parse the bootfile env var / cmd line param 849 * 850 * @param ipaddr - a pointer to the ipaddr to populate if included in bootfile 851 * @param filename - a pointer to the string to save the filename part 852 * @param max_len - The longest - 1 that the filename part can be 853 * 854 * return 1 if parsed, 0 if bootfile is empty 855 */ 856 int net_parse_bootfile(struct in_addr *ipaddr, char *filename, int max_len); 857 858 /* get a random source port */ 859 unsigned int random_port(void); 860 861 /** 862 * update_tftp - Update firmware over TFTP (via DFU) 863 * 864 * This function updates board's firmware via TFTP 865 * 866 * @param addr - memory address where data is stored 867 * @param interface - the DFU medium name - e.g. "mmc" 868 * @param devstring - the DFU medium number - e.g. "1" 869 * 870 * @return - 0 on success, other value on failure 871 */ 872 int update_tftp(ulong addr, char *interface, char *devstring); 873 874 /**********************************************************************/ 875 876 #endif /* __NET_H__ */ 877