1 /* 2 * LiMon Monitor (LiMon) - Network. 3 * 4 * Copyright 1994 - 2000 Neil Russell. 5 * (See License) 6 * SPDX-License-Identifier: GPL-2.0 7 * 8 * History 9 * 9/16/00 bor adapted to TQM823L/STK8xxL board, RARP/TFTP boot added 10 */ 11 12 #ifndef __NET_H__ 13 #define __NET_H__ 14 15 #include <asm/cache.h> 16 #include <asm/byteorder.h> /* for nton* / ntoh* stuff */ 17 18 #define DEBUG_LL_STATE 0 /* Link local state machine changes */ 19 #define DEBUG_DEV_PKT 0 /* Packets or info directed to the device */ 20 #define DEBUG_NET_PKT 0 /* Packets on info on the network at large */ 21 #define DEBUG_INT_STATE 0 /* Internal network state changes */ 22 23 /* 24 * The number of receive packet buffers, and the required packet buffer 25 * alignment in memory. 26 * 27 */ 28 29 #ifdef CONFIG_SYS_RX_ETH_BUFFER 30 # define PKTBUFSRX CONFIG_SYS_RX_ETH_BUFFER 31 #else 32 # define PKTBUFSRX 4 33 #endif 34 35 #define PKTALIGN ARCH_DMA_MINALIGN 36 37 /* ARP hardware address length */ 38 #define ARP_HLEN 6 39 /* 40 * The size of a MAC address in string form, each digit requires two chars 41 * and five separator characters to form '00:00:00:00:00:00'. 42 */ 43 #define ARP_HLEN_ASCII (ARP_HLEN * 2) + (ARP_HLEN - 1) 44 45 /* IPv4 addresses are always 32 bits in size */ 46 struct in_addr { 47 __be32 s_addr; 48 }; 49 50 /** 51 * An incoming packet handler. 52 * @param pkt pointer to the application packet 53 * @param dport destination UDP port 54 * @param sip source IP address 55 * @param sport source UDP port 56 * @param len packet length 57 */ 58 typedef void rxhand_f(uchar *pkt, unsigned dport, 59 struct in_addr sip, unsigned sport, 60 unsigned len); 61 62 /** 63 * An incoming ICMP packet handler. 64 * @param type ICMP type 65 * @param code ICMP code 66 * @param dport destination UDP port 67 * @param sip source IP address 68 * @param sport source UDP port 69 * @param pkt pointer to the ICMP packet data 70 * @param len packet length 71 */ 72 typedef void rxhand_icmp_f(unsigned type, unsigned code, unsigned dport, 73 struct in_addr sip, unsigned sport, uchar *pkt, unsigned len); 74 75 /* 76 * A timeout handler. Called after time interval has expired. 77 */ 78 typedef void thand_f(void); 79 80 enum eth_state_t { 81 ETH_STATE_INIT, 82 ETH_STATE_PASSIVE, 83 ETH_STATE_ACTIVE 84 }; 85 86 #ifdef CONFIG_DM_ETH 87 /** 88 * struct eth_pdata - Platform data for Ethernet MAC controllers 89 * 90 * @iobase: The base address of the hardware registers 91 * @enetaddr: The Ethernet MAC address that is loaded from EEPROM or env 92 * @phy_interface: PHY interface to use - see PHY_INTERFACE_MODE_... 93 * @max_speed: Maximum speed of Ethernet connection supported by MAC 94 */ 95 struct eth_pdata { 96 phys_addr_t iobase; 97 unsigned char enetaddr[ARP_HLEN]; 98 int phy_interface; 99 int max_speed; 100 }; 101 102 enum eth_recv_flags { 103 /* 104 * Check hardware device for new packets (otherwise only return those 105 * which are already in the memory buffer ready to process) 106 */ 107 ETH_RECV_CHECK_DEVICE = 1 << 0, 108 }; 109 110 /** 111 * struct eth_ops - functions of Ethernet MAC controllers 112 * 113 * start: Prepare the hardware to send and receive packets 114 * send: Send the bytes passed in "packet" as a packet on the wire 115 * recv: Check if the hardware received a packet. If so, set the pointer to the 116 * packet buffer in the packetp parameter. If not, return an error or 0 to 117 * indicate that the hardware receive FIFO is empty. If 0 is returned, the 118 * network stack will not process the empty packet, but free_pkt() will be 119 * called if supplied 120 * free_pkt: Give the driver an opportunity to manage its packet buffer memory 121 * when the network stack is finished processing it. This will only be 122 * called when no error was returned from recv - optional 123 * stop: Stop the hardware from looking for packets - may be called even if 124 * state == PASSIVE 125 * mcast: Join or leave a multicast group (for TFTP) - optional 126 * write_hwaddr: Write a MAC address to the hardware (used to pass it to Linux 127 * on some platforms like ARM). This function expects the 128 * eth_pdata::enetaddr field to be populated. The method can 129 * return -ENOSYS to indicate that this is not implemented for 130 this hardware - optional. 131 * read_rom_hwaddr: Some devices have a backup of the MAC address stored in a 132 * ROM on the board. This is how the driver should expose it 133 * to the network stack. This function should fill in the 134 * eth_pdata::enetaddr field - optional 135 */ 136 struct eth_ops { 137 int (*start)(struct udevice *dev); 138 int (*send)(struct udevice *dev, void *packet, int length); 139 int (*recv)(struct udevice *dev, int flags, uchar **packetp); 140 int (*free_pkt)(struct udevice *dev, uchar *packet, int length); 141 void (*stop)(struct udevice *dev); 142 #ifdef CONFIG_MCAST_TFTP 143 int (*mcast)(struct udevice *dev, const u8 *enetaddr, int join); 144 #endif 145 int (*write_hwaddr)(struct udevice *dev); 146 int (*read_rom_hwaddr)(struct udevice *dev); 147 }; 148 149 #define eth_get_ops(dev) ((struct eth_ops *)(dev)->driver->ops) 150 151 struct udevice *eth_get_dev(void); /* get the current device */ 152 /* 153 * The devname can be either an exact name given by the driver or device tree 154 * or it can be an alias of the form "eth%d" 155 */ 156 struct udevice *eth_get_dev_by_name(const char *devname); 157 unsigned char *eth_get_ethaddr(void); /* get the current device MAC */ 158 159 /* Used only when NetConsole is enabled */ 160 int eth_is_active(struct udevice *dev); /* Test device for active state */ 161 int eth_init_state_only(void); /* Set active state */ 162 void eth_halt_state_only(void); /* Set passive state */ 163 #endif 164 165 #ifndef CONFIG_DM_ETH 166 struct eth_device { 167 #define ETH_NAME_LEN 16 168 char name[ETH_NAME_LEN]; 169 unsigned char enetaddr[ARP_HLEN]; 170 phys_addr_t iobase; 171 int state; 172 173 int (*init)(struct eth_device *, bd_t *); 174 int (*send)(struct eth_device *, void *packet, int length); 175 int (*recv)(struct eth_device *); 176 void (*halt)(struct eth_device *); 177 #ifdef CONFIG_MCAST_TFTP 178 int (*mcast)(struct eth_device *, const u8 *enetaddr, u8 set); 179 #endif 180 int (*write_hwaddr)(struct eth_device *); 181 struct eth_device *next; 182 int index; 183 void *priv; 184 }; 185 186 int eth_register(struct eth_device *dev);/* Register network device */ 187 int eth_unregister(struct eth_device *dev);/* Remove network device */ 188 189 extern struct eth_device *eth_current; 190 191 static __always_inline struct eth_device *eth_get_dev(void) 192 { 193 return eth_current; 194 } 195 struct eth_device *eth_get_dev_by_name(const char *devname); 196 struct eth_device *eth_get_dev_by_index(int index); /* get dev @ index */ 197 198 /* get the current device MAC */ 199 static inline unsigned char *eth_get_ethaddr(void) 200 { 201 if (eth_current) 202 return eth_current->enetaddr; 203 return NULL; 204 } 205 206 /* Used only when NetConsole is enabled */ 207 int eth_is_active(struct eth_device *dev); /* Test device for active state */ 208 /* Set active state */ 209 static __always_inline int eth_init_state_only(void) 210 { 211 eth_get_dev()->state = ETH_STATE_ACTIVE; 212 213 return 0; 214 } 215 /* Set passive state */ 216 static __always_inline void eth_halt_state_only(void) 217 { 218 eth_get_dev()->state = ETH_STATE_PASSIVE; 219 } 220 221 /* 222 * Set the hardware address for an ethernet interface based on 'eth%daddr' 223 * environment variable (or just 'ethaddr' if eth_number is 0). 224 * Args: 225 * base_name - base name for device (normally "eth") 226 * eth_number - value of %d (0 for first device of this type) 227 * Returns: 228 * 0 is success, non-zero is error status from driver. 229 */ 230 int eth_write_hwaddr(struct eth_device *dev, const char *base_name, 231 int eth_number); 232 233 int usb_eth_initialize(bd_t *bi); 234 #endif 235 236 int eth_initialize(void); /* Initialize network subsystem */ 237 void eth_try_another(int first_restart); /* Change the device */ 238 void eth_set_current(void); /* set nterface to ethcur var */ 239 240 int eth_get_dev_index(void); /* get the device index */ 241 void eth_parse_enetaddr(const char *addr, uchar *enetaddr); 242 int eth_getenv_enetaddr(const char *name, uchar *enetaddr); 243 int eth_setenv_enetaddr(const char *name, const uchar *enetaddr); 244 245 /** 246 * eth_setenv_enetaddr_by_index() - set the MAC address environment variable 247 * 248 * This sets up an environment variable with the given MAC address (@enetaddr). 249 * The environment variable to be set is defined by <@base_name><@index>addr. 250 * If @index is 0 it is omitted. For common Ethernet this means ethaddr, 251 * eth1addr, etc. 252 * 253 * @base_name: Base name for variable, typically "eth" 254 * @index: Index of interface being updated (>=0) 255 * @enetaddr: Pointer to MAC address to put into the variable 256 * @return 0 if OK, other value on error 257 */ 258 int eth_setenv_enetaddr_by_index(const char *base_name, int index, 259 uchar *enetaddr); 260 261 262 /* 263 * Initialize USB ethernet device with CONFIG_DM_ETH 264 * Returns: 265 * 0 is success, non-zero is error status. 266 */ 267 int usb_ether_init(void); 268 269 /* 270 * Get the hardware address for an ethernet interface . 271 * Args: 272 * base_name - base name for device (normally "eth") 273 * index - device index number (0 for first) 274 * enetaddr - returns 6 byte hardware address 275 * Returns: 276 * Return true if the address is valid. 277 */ 278 int eth_getenv_enetaddr_by_index(const char *base_name, int index, 279 uchar *enetaddr); 280 281 int eth_init(void); /* Initialize the device */ 282 int eth_send(void *packet, int length); /* Send a packet */ 283 284 #if defined(CONFIG_API) || defined(CONFIG_EFI_LOADER) 285 int eth_receive(void *packet, int length); /* Receive a packet*/ 286 extern void (*push_packet)(void *packet, int length); 287 #endif 288 int eth_rx(void); /* Check for received packets */ 289 void eth_halt(void); /* stop SCC */ 290 const char *eth_get_name(void); /* get name of current device */ 291 292 #ifdef CONFIG_MCAST_TFTP 293 int eth_mcast_join(struct in_addr mcast_addr, int join); 294 u32 ether_crc(size_t len, unsigned char const *p); 295 #endif 296 297 298 /**********************************************************************/ 299 /* 300 * Protocol headers. 301 */ 302 303 /* 304 * Ethernet header 305 */ 306 307 struct ethernet_hdr { 308 u8 et_dest[ARP_HLEN]; /* Destination node */ 309 u8 et_src[ARP_HLEN]; /* Source node */ 310 u16 et_protlen; /* Protocol or length */ 311 }; 312 313 /* Ethernet header size */ 314 #define ETHER_HDR_SIZE (sizeof(struct ethernet_hdr)) 315 316 #define ETH_FCS_LEN 4 /* Octets in the FCS */ 317 318 struct e802_hdr { 319 u8 et_dest[ARP_HLEN]; /* Destination node */ 320 u8 et_src[ARP_HLEN]; /* Source node */ 321 u16 et_protlen; /* Protocol or length */ 322 u8 et_dsap; /* 802 DSAP */ 323 u8 et_ssap; /* 802 SSAP */ 324 u8 et_ctl; /* 802 control */ 325 u8 et_snap1; /* SNAP */ 326 u8 et_snap2; 327 u8 et_snap3; 328 u16 et_prot; /* 802 protocol */ 329 }; 330 331 /* 802 + SNAP + ethernet header size */ 332 #define E802_HDR_SIZE (sizeof(struct e802_hdr)) 333 334 /* 335 * Virtual LAN Ethernet header 336 */ 337 struct vlan_ethernet_hdr { 338 u8 vet_dest[ARP_HLEN]; /* Destination node */ 339 u8 vet_src[ARP_HLEN]; /* Source node */ 340 u16 vet_vlan_type; /* PROT_VLAN */ 341 u16 vet_tag; /* TAG of VLAN */ 342 u16 vet_type; /* protocol type */ 343 }; 344 345 /* VLAN Ethernet header size */ 346 #define VLAN_ETHER_HDR_SIZE (sizeof(struct vlan_ethernet_hdr)) 347 348 #define PROT_IP 0x0800 /* IP protocol */ 349 #define PROT_ARP 0x0806 /* IP ARP protocol */ 350 #define PROT_RARP 0x8035 /* IP ARP protocol */ 351 #define PROT_VLAN 0x8100 /* IEEE 802.1q protocol */ 352 #define PROT_IPV6 0x86dd /* IPv6 over bluebook */ 353 #define PROT_PPP_SES 0x8864 /* PPPoE session messages */ 354 355 #define IPPROTO_ICMP 1 /* Internet Control Message Protocol */ 356 #define IPPROTO_UDP 17 /* User Datagram Protocol */ 357 358 /* 359 * Internet Protocol (IP) header. 360 */ 361 struct ip_hdr { 362 u8 ip_hl_v; /* header length and version */ 363 u8 ip_tos; /* type of service */ 364 u16 ip_len; /* total length */ 365 u16 ip_id; /* identification */ 366 u16 ip_off; /* fragment offset field */ 367 u8 ip_ttl; /* time to live */ 368 u8 ip_p; /* protocol */ 369 u16 ip_sum; /* checksum */ 370 struct in_addr ip_src; /* Source IP address */ 371 struct in_addr ip_dst; /* Destination IP address */ 372 }; 373 374 #define IP_OFFS 0x1fff /* ip offset *= 8 */ 375 #define IP_FLAGS 0xe000 /* first 3 bits */ 376 #define IP_FLAGS_RES 0x8000 /* reserved */ 377 #define IP_FLAGS_DFRAG 0x4000 /* don't fragments */ 378 #define IP_FLAGS_MFRAG 0x2000 /* more fragments */ 379 380 #define IP_HDR_SIZE (sizeof(struct ip_hdr)) 381 382 /* 383 * Internet Protocol (IP) + UDP header. 384 */ 385 struct ip_udp_hdr { 386 u8 ip_hl_v; /* header length and version */ 387 u8 ip_tos; /* type of service */ 388 u16 ip_len; /* total length */ 389 u16 ip_id; /* identification */ 390 u16 ip_off; /* fragment offset field */ 391 u8 ip_ttl; /* time to live */ 392 u8 ip_p; /* protocol */ 393 u16 ip_sum; /* checksum */ 394 struct in_addr ip_src; /* Source IP address */ 395 struct in_addr ip_dst; /* Destination IP address */ 396 u16 udp_src; /* UDP source port */ 397 u16 udp_dst; /* UDP destination port */ 398 u16 udp_len; /* Length of UDP packet */ 399 u16 udp_xsum; /* Checksum */ 400 }; 401 402 #define IP_UDP_HDR_SIZE (sizeof(struct ip_udp_hdr)) 403 #define UDP_HDR_SIZE (IP_UDP_HDR_SIZE - IP_HDR_SIZE) 404 405 /* 406 * Address Resolution Protocol (ARP) header. 407 */ 408 struct arp_hdr { 409 u16 ar_hrd; /* Format of hardware address */ 410 # define ARP_ETHER 1 /* Ethernet hardware address */ 411 u16 ar_pro; /* Format of protocol address */ 412 u8 ar_hln; /* Length of hardware address */ 413 u8 ar_pln; /* Length of protocol address */ 414 # define ARP_PLEN 4 415 u16 ar_op; /* Operation */ 416 # define ARPOP_REQUEST 1 /* Request to resolve address */ 417 # define ARPOP_REPLY 2 /* Response to previous request */ 418 419 # define RARPOP_REQUEST 3 /* Request to resolve address */ 420 # define RARPOP_REPLY 4 /* Response to previous request */ 421 422 /* 423 * The remaining fields are variable in size, according to 424 * the sizes above, and are defined as appropriate for 425 * specific hardware/protocol combinations. 426 */ 427 u8 ar_data[0]; 428 #define ar_sha ar_data[0] 429 #define ar_spa ar_data[ARP_HLEN] 430 #define ar_tha ar_data[ARP_HLEN + ARP_PLEN] 431 #define ar_tpa ar_data[ARP_HLEN + ARP_PLEN + ARP_HLEN] 432 #if 0 433 u8 ar_sha[]; /* Sender hardware address */ 434 u8 ar_spa[]; /* Sender protocol address */ 435 u8 ar_tha[]; /* Target hardware address */ 436 u8 ar_tpa[]; /* Target protocol address */ 437 #endif /* 0 */ 438 }; 439 440 #define ARP_HDR_SIZE (8+20) /* Size assuming ethernet */ 441 442 /* 443 * ICMP stuff (just enough to handle (host) redirect messages) 444 */ 445 #define ICMP_ECHO_REPLY 0 /* Echo reply */ 446 #define ICMP_NOT_REACH 3 /* Detination unreachable */ 447 #define ICMP_REDIRECT 5 /* Redirect (change route) */ 448 #define ICMP_ECHO_REQUEST 8 /* Echo request */ 449 450 /* Codes for REDIRECT. */ 451 #define ICMP_REDIR_NET 0 /* Redirect Net */ 452 #define ICMP_REDIR_HOST 1 /* Redirect Host */ 453 454 /* Codes for NOT_REACH */ 455 #define ICMP_NOT_REACH_PORT 3 /* Port unreachable */ 456 457 struct icmp_hdr { 458 u8 type; 459 u8 code; 460 u16 checksum; 461 union { 462 struct { 463 u16 id; 464 u16 sequence; 465 } echo; 466 u32 gateway; 467 struct { 468 u16 unused; 469 u16 mtu; 470 } frag; 471 u8 data[0]; 472 } un; 473 }; 474 475 #define ICMP_HDR_SIZE (sizeof(struct icmp_hdr)) 476 #define IP_ICMP_HDR_SIZE (IP_HDR_SIZE + ICMP_HDR_SIZE) 477 478 /* 479 * Maximum packet size; used to allocate packet storage. Use 480 * the maxium Ethernet frame size as specified by the Ethernet 481 * standard including the 802.1Q tag (VLAN tagging). 482 * maximum packet size = 1522 483 * maximum packet size and multiple of 32 bytes = 1536 484 */ 485 #define PKTSIZE 1522 486 #define PKTSIZE_ALIGN 1536 487 488 /* 489 * Maximum receive ring size; that is, the number of packets 490 * we can buffer before overflow happens. Basically, this just 491 * needs to be enough to prevent a packet being discarded while 492 * we are processing the previous one. 493 */ 494 #define RINGSZ 4 495 #define RINGSZ_LOG2 2 496 497 /**********************************************************************/ 498 /* 499 * Globals. 500 * 501 * Note: 502 * 503 * All variables of type struct in_addr are stored in NETWORK byte order 504 * (big endian). 505 */ 506 507 /* net.c */ 508 /** BOOTP EXTENTIONS **/ 509 extern struct in_addr net_gateway; /* Our gateway IP address */ 510 extern struct in_addr net_netmask; /* Our subnet mask (0 = unknown) */ 511 /* Our Domain Name Server (0 = unknown) */ 512 extern struct in_addr net_dns_server; 513 #if defined(CONFIG_BOOTP_DNS2) 514 /* Our 2nd Domain Name Server (0 = unknown) */ 515 extern struct in_addr net_dns_server2; 516 #endif 517 extern char net_nis_domain[32]; /* Our IS domain */ 518 extern char net_hostname[32]; /* Our hostname */ 519 extern char net_root_path[64]; /* Our root path */ 520 /** END OF BOOTP EXTENTIONS **/ 521 extern u8 net_ethaddr[ARP_HLEN]; /* Our ethernet address */ 522 extern u8 net_server_ethaddr[ARP_HLEN]; /* Boot server enet address */ 523 extern struct in_addr net_ip; /* Our IP addr (0 = unknown) */ 524 extern struct in_addr net_server_ip; /* Server IP addr (0 = unknown) */ 525 extern uchar *net_tx_packet; /* THE transmit packet */ 526 extern uchar *net_rx_packets[PKTBUFSRX]; /* Receive packets */ 527 extern uchar *net_rx_packet; /* Current receive packet */ 528 extern int net_rx_packet_len; /* Current rx packet length */ 529 extern const u8 net_bcast_ethaddr[ARP_HLEN]; /* Ethernet broadcast address */ 530 extern const u8 net_null_ethaddr[ARP_HLEN]; 531 532 #define VLAN_NONE 4095 /* untagged */ 533 #define VLAN_IDMASK 0x0fff /* mask of valid vlan id */ 534 extern ushort net_our_vlan; /* Our VLAN */ 535 extern ushort net_native_vlan; /* Our Native VLAN */ 536 537 extern int net_restart_wrap; /* Tried all network devices */ 538 539 enum proto_t { 540 BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP, 541 TFTPSRV, TFTPPUT, LINKLOCAL 542 }; 543 544 extern char net_boot_file_name[1024];/* Boot File name */ 545 /* The actual transferred size of the bootfile (in bytes) */ 546 extern u32 net_boot_file_size; 547 /* Boot file size in blocks as reported by the DHCP server */ 548 extern u32 net_boot_file_expected_size_in_blocks; 549 550 #if defined(CONFIG_CMD_DNS) 551 extern char *net_dns_resolve; /* The host to resolve */ 552 extern char *net_dns_env_var; /* the env var to put the ip into */ 553 #endif 554 555 #if defined(CONFIG_CMD_PING) 556 extern struct in_addr net_ping_ip; /* the ip address to ping */ 557 #endif 558 559 #if defined(CONFIG_CMD_CDP) 560 /* when CDP completes these hold the return values */ 561 extern ushort cdp_native_vlan; /* CDP returned native VLAN */ 562 extern ushort cdp_appliance_vlan; /* CDP returned appliance VLAN */ 563 564 /* 565 * Check for a CDP packet by examining the received MAC address field 566 */ 567 static inline int is_cdp_packet(const uchar *ethaddr) 568 { 569 extern const u8 net_cdp_ethaddr[ARP_HLEN]; 570 571 return memcmp(ethaddr, net_cdp_ethaddr, ARP_HLEN) == 0; 572 } 573 #endif 574 575 #if defined(CONFIG_CMD_SNTP) 576 extern struct in_addr net_ntp_server; /* the ip address to NTP */ 577 extern int net_ntp_time_offset; /* offset time from UTC */ 578 #endif 579 580 #if defined(CONFIG_MCAST_TFTP) 581 extern struct in_addr net_mcast_addr; 582 #endif 583 584 /* Initialize the network adapter */ 585 void net_init(void); 586 int net_loop(enum proto_t); 587 588 /* Load failed. Start again. */ 589 int net_start_again(void); 590 591 /* Get size of the ethernet header when we send */ 592 int net_eth_hdr_size(void); 593 594 /* Set ethernet header; returns the size of the header */ 595 int net_set_ether(uchar *xet, const uchar *dest_ethaddr, uint prot); 596 int net_update_ether(struct ethernet_hdr *et, uchar *addr, uint prot); 597 598 /* Set IP header */ 599 void net_set_ip_header(uchar *pkt, struct in_addr dest, struct in_addr source); 600 void net_set_udp_header(uchar *pkt, struct in_addr dest, int dport, 601 int sport, int len); 602 603 /** 604 * compute_ip_checksum() - Compute IP checksum 605 * 606 * @addr: Address to check (must be 16-bit aligned) 607 * @nbytes: Number of bytes to check (normally a multiple of 2) 608 * @return 16-bit IP checksum 609 */ 610 unsigned compute_ip_checksum(const void *addr, unsigned nbytes); 611 612 /** 613 * add_ip_checksums() - add two IP checksums 614 * 615 * @offset: Offset of first sum (if odd we do a byte-swap) 616 * @sum: First checksum 617 * @new_sum: New checksum to add 618 * @return updated 16-bit IP checksum 619 */ 620 unsigned add_ip_checksums(unsigned offset, unsigned sum, unsigned new_sum); 621 622 /** 623 * ip_checksum_ok() - check if a checksum is correct 624 * 625 * This works by making sure the checksum sums to 0 626 * 627 * @addr: Address to check (must be 16-bit aligned) 628 * @nbytes: Number of bytes to check (normally a multiple of 2) 629 * @return true if the checksum matches, false if not 630 */ 631 int ip_checksum_ok(const void *addr, unsigned nbytes); 632 633 /* Callbacks */ 634 rxhand_f *net_get_udp_handler(void); /* Get UDP RX packet handler */ 635 void net_set_udp_handler(rxhand_f *); /* Set UDP RX packet handler */ 636 rxhand_f *net_get_arp_handler(void); /* Get ARP RX packet handler */ 637 void net_set_arp_handler(rxhand_f *); /* Set ARP RX packet handler */ 638 void net_set_icmp_handler(rxhand_icmp_f *f); /* Set ICMP RX handler */ 639 void net_set_timeout_handler(ulong, thand_f *);/* Set timeout handler */ 640 641 /* Network loop state */ 642 enum net_loop_state { 643 NETLOOP_CONTINUE, 644 NETLOOP_RESTART, 645 NETLOOP_SUCCESS, 646 NETLOOP_FAIL 647 }; 648 extern enum net_loop_state net_state; 649 650 static inline void net_set_state(enum net_loop_state state) 651 { 652 debug_cond(DEBUG_INT_STATE, "--- NetState set to %d\n", state); 653 net_state = state; 654 } 655 656 /* Transmit a packet */ 657 static inline void net_send_packet(uchar *pkt, int len) 658 { 659 /* Currently no way to return errors from eth_send() */ 660 (void) eth_send(pkt, len); 661 } 662 663 /* 664 * Transmit "net_tx_packet" as UDP packet, performing ARP request if needed 665 * (ether will be populated) 666 * 667 * @param ether Raw packet buffer 668 * @param dest IP address to send the datagram to 669 * @param dport Destination UDP port 670 * @param sport Source UDP port 671 * @param payload_len Length of data after the UDP header 672 */ 673 int net_send_udp_packet(uchar *ether, struct in_addr dest, int dport, 674 int sport, int payload_len); 675 676 /* Processes a received packet */ 677 void net_process_received_packet(uchar *in_packet, int len); 678 679 #ifdef CONFIG_NETCONSOLE 680 void nc_start(void); 681 int nc_input_packet(uchar *pkt, struct in_addr src_ip, unsigned dest_port, 682 unsigned src_port, unsigned len); 683 #endif 684 685 static __always_inline int eth_is_on_demand_init(void) 686 { 687 #ifdef CONFIG_NETCONSOLE 688 extern enum proto_t net_loop_last_protocol; 689 690 return net_loop_last_protocol != NETCONS; 691 #else 692 return 1; 693 #endif 694 } 695 696 static inline void eth_set_last_protocol(int protocol) 697 { 698 #ifdef CONFIG_NETCONSOLE 699 extern enum proto_t net_loop_last_protocol; 700 701 net_loop_last_protocol = protocol; 702 #endif 703 } 704 705 /* 706 * Check if autoload is enabled. If so, use either NFS or TFTP to download 707 * the boot file. 708 */ 709 void net_auto_load(void); 710 711 /* 712 * The following functions are a bit ugly, but necessary to deal with 713 * alignment restrictions on ARM. 714 * 715 * We're using inline functions, which had the smallest memory 716 * footprint in our tests. 717 */ 718 /* return IP *in network byteorder* */ 719 static inline struct in_addr net_read_ip(void *from) 720 { 721 struct in_addr ip; 722 723 memcpy((void *)&ip, (void *)from, sizeof(ip)); 724 return ip; 725 } 726 727 /* return ulong *in network byteorder* */ 728 static inline u32 net_read_u32(u32 *from) 729 { 730 u32 l; 731 732 memcpy((void *)&l, (void *)from, sizeof(l)); 733 return l; 734 } 735 736 /* write IP *in network byteorder* */ 737 static inline void net_write_ip(void *to, struct in_addr ip) 738 { 739 memcpy(to, (void *)&ip, sizeof(ip)); 740 } 741 742 /* copy IP */ 743 static inline void net_copy_ip(void *to, void *from) 744 { 745 memcpy((void *)to, from, sizeof(struct in_addr)); 746 } 747 748 /* copy ulong */ 749 static inline void net_copy_u32(u32 *to, u32 *from) 750 { 751 memcpy((void *)to, (void *)from, sizeof(u32)); 752 } 753 754 /** 755 * is_zero_ethaddr - Determine if give Ethernet address is all zeros. 756 * @addr: Pointer to a six-byte array containing the Ethernet address 757 * 758 * Return true if the address is all zeroes. 759 */ 760 static inline int is_zero_ethaddr(const u8 *addr) 761 { 762 return !(addr[0] | addr[1] | addr[2] | addr[3] | addr[4] | addr[5]); 763 } 764 765 /** 766 * is_multicast_ethaddr - Determine if the Ethernet address is a multicast. 767 * @addr: Pointer to a six-byte array containing the Ethernet address 768 * 769 * Return true if the address is a multicast address. 770 * By definition the broadcast address is also a multicast address. 771 */ 772 static inline int is_multicast_ethaddr(const u8 *addr) 773 { 774 return 0x01 & addr[0]; 775 } 776 777 /* 778 * is_broadcast_ethaddr - Determine if the Ethernet address is broadcast 779 * @addr: Pointer to a six-byte array containing the Ethernet address 780 * 781 * Return true if the address is the broadcast address. 782 */ 783 static inline int is_broadcast_ethaddr(const u8 *addr) 784 { 785 return (addr[0] & addr[1] & addr[2] & addr[3] & addr[4] & addr[5]) == 786 0xff; 787 } 788 789 /* 790 * is_valid_ethaddr - Determine if the given Ethernet address is valid 791 * @addr: Pointer to a six-byte array containing the Ethernet address 792 * 793 * Check that the Ethernet address (MAC) is not 00:00:00:00:00:00, is not 794 * a multicast address, and is not FF:FF:FF:FF:FF:FF. 795 * 796 * Return true if the address is valid. 797 */ 798 static inline int is_valid_ethaddr(const u8 *addr) 799 { 800 /* FF:FF:FF:FF:FF:FF is a multicast address so we don't need to 801 * explicitly check for it here. */ 802 return !is_multicast_ethaddr(addr) && !is_zero_ethaddr(addr); 803 } 804 805 /** 806 * net_random_ethaddr - Generate software assigned random Ethernet address 807 * @addr: Pointer to a six-byte array containing the Ethernet address 808 * 809 * Generate a random Ethernet address (MAC) that is not multicast 810 * and has the local assigned bit set. 811 */ 812 static inline void net_random_ethaddr(uchar *addr) 813 { 814 int i; 815 unsigned int seed = get_timer(0); 816 817 for (i = 0; i < 6; i++) 818 addr[i] = rand_r(&seed); 819 820 addr[0] &= 0xfe; /* clear multicast bit */ 821 addr[0] |= 0x02; /* set local assignment bit (IEEE802) */ 822 } 823 824 /* Convert an IP address to a string */ 825 void ip_to_string(struct in_addr x, char *s); 826 827 /* Convert a string to ip address */ 828 struct in_addr string_to_ip(const char *s); 829 830 /* Convert a VLAN id to a string */ 831 void vlan_to_string(ushort x, char *s); 832 833 /* Convert a string to a vlan id */ 834 ushort string_to_vlan(const char *s); 835 836 /* read a VLAN id from an environment variable */ 837 ushort getenv_vlan(char *); 838 839 /* copy a filename (allow for "..." notation, limit length) */ 840 void copy_filename(char *dst, const char *src, int size); 841 842 /* get a random source port */ 843 unsigned int random_port(void); 844 845 /** 846 * update_tftp - Update firmware over TFTP (via DFU) 847 * 848 * This function updates board's firmware via TFTP 849 * 850 * @param addr - memory address where data is stored 851 * @param interface - the DFU medium name - e.g. "mmc" 852 * @param devstring - the DFU medium number - e.g. "1" 853 * 854 * @return - 0 on success, other value on failure 855 */ 856 int update_tftp(ulong addr, char *interface, char *devstring); 857 858 /**********************************************************************/ 859 860 #endif /* __NET_H__ */ 861