1 /* 2 * LiMon Monitor (LiMon) - Network. 3 * 4 * Copyright 1994 - 2000 Neil Russell. 5 * (See License) 6 * SPDX-License-Identifier: GPL-2.0 7 * 8 * History 9 * 9/16/00 bor adapted to TQM823L/STK8xxL board, RARP/TFTP boot added 10 */ 11 12 #ifndef __NET_H__ 13 #define __NET_H__ 14 15 #if defined(CONFIG_8xx) 16 #include <commproc.h> 17 #endif /* CONFIG_8xx */ 18 19 #include <asm/cache.h> 20 #include <asm/byteorder.h> /* for nton* / ntoh* stuff */ 21 22 #define DEBUG_LL_STATE 0 /* Link local state machine changes */ 23 #define DEBUG_DEV_PKT 0 /* Packets or info directed to the device */ 24 #define DEBUG_NET_PKT 0 /* Packets on info on the network at large */ 25 #define DEBUG_INT_STATE 0 /* Internal network state changes */ 26 27 /* 28 * The number of receive packet buffers, and the required packet buffer 29 * alignment in memory. 30 * 31 */ 32 33 #ifdef CONFIG_SYS_RX_ETH_BUFFER 34 # define PKTBUFSRX CONFIG_SYS_RX_ETH_BUFFER 35 #else 36 # define PKTBUFSRX 4 37 #endif 38 39 #define PKTALIGN ARCH_DMA_MINALIGN 40 41 /* IPv4 addresses are always 32 bits in size */ 42 struct in_addr { 43 __be32 s_addr; 44 }; 45 46 /** 47 * An incoming packet handler. 48 * @param pkt pointer to the application packet 49 * @param dport destination UDP port 50 * @param sip source IP address 51 * @param sport source UDP port 52 * @param len packet length 53 */ 54 typedef void rxhand_f(uchar *pkt, unsigned dport, 55 struct in_addr sip, unsigned sport, 56 unsigned len); 57 58 /** 59 * An incoming ICMP packet handler. 60 * @param type ICMP type 61 * @param code ICMP code 62 * @param dport destination UDP port 63 * @param sip source IP address 64 * @param sport source UDP port 65 * @param pkt pointer to the ICMP packet data 66 * @param len packet length 67 */ 68 typedef void rxhand_icmp_f(unsigned type, unsigned code, unsigned dport, 69 struct in_addr sip, unsigned sport, uchar *pkt, unsigned len); 70 71 /* 72 * A timeout handler. Called after time interval has expired. 73 */ 74 typedef void thand_f(void); 75 76 enum eth_state_t { 77 ETH_STATE_INIT, 78 ETH_STATE_PASSIVE, 79 ETH_STATE_ACTIVE 80 }; 81 82 #ifdef CONFIG_DM_ETH 83 /** 84 * struct eth_pdata - Platform data for Ethernet MAC controllers 85 * 86 * @iobase: The base address of the hardware registers 87 * @enetaddr: The Ethernet MAC address that is loaded from EEPROM or env 88 * @phy_interface: PHY interface to use - see PHY_INTERFACE_MODE_... 89 * @max_speed: Maximum speed of Ethernet connection supported by MAC 90 */ 91 struct eth_pdata { 92 phys_addr_t iobase; 93 unsigned char enetaddr[6]; 94 int phy_interface; 95 int max_speed; 96 }; 97 98 enum eth_recv_flags { 99 /* 100 * Check hardware device for new packets (otherwise only return those 101 * which are already in the memory buffer ready to process) 102 */ 103 ETH_RECV_CHECK_DEVICE = 1 << 0, 104 }; 105 106 /** 107 * struct eth_ops - functions of Ethernet MAC controllers 108 * 109 * start: Prepare the hardware to send and receive packets 110 * send: Send the bytes passed in "packet" as a packet on the wire 111 * recv: Check if the hardware received a packet. If so, set the pointer to the 112 * packet buffer in the packetp parameter. If not, return an error or 0 to 113 * indicate that the hardware receive FIFO is empty. If 0 is returned, the 114 * network stack will not process the empty packet, but free_pkt() will be 115 * called if supplied 116 * free_pkt: Give the driver an opportunity to manage its packet buffer memory 117 * when the network stack is finished processing it. This will only be 118 * called when no error was returned from recv - optional 119 * stop: Stop the hardware from looking for packets - may be called even if 120 * state == PASSIVE 121 * mcast: Join or leave a multicast group (for TFTP) - optional 122 * write_hwaddr: Write a MAC address to the hardware (used to pass it to Linux 123 * on some platforms like ARM). This function expects the 124 * eth_pdata::enetaddr field to be populated. The method can 125 * return -ENOSYS to indicate that this is not implemented for 126 this hardware - optional. 127 * read_rom_hwaddr: Some devices have a backup of the MAC address stored in a 128 * ROM on the board. This is how the driver should expose it 129 * to the network stack. This function should fill in the 130 * eth_pdata::enetaddr field - optional 131 */ 132 struct eth_ops { 133 int (*start)(struct udevice *dev); 134 int (*send)(struct udevice *dev, void *packet, int length); 135 int (*recv)(struct udevice *dev, int flags, uchar **packetp); 136 int (*free_pkt)(struct udevice *dev, uchar *packet, int length); 137 void (*stop)(struct udevice *dev); 138 #ifdef CONFIG_MCAST_TFTP 139 int (*mcast)(struct udevice *dev, const u8 *enetaddr, int join); 140 #endif 141 int (*write_hwaddr)(struct udevice *dev); 142 int (*read_rom_hwaddr)(struct udevice *dev); 143 }; 144 145 #define eth_get_ops(dev) ((struct eth_ops *)(dev)->driver->ops) 146 147 struct udevice *eth_get_dev(void); /* get the current device */ 148 /* 149 * The devname can be either an exact name given by the driver or device tree 150 * or it can be an alias of the form "eth%d" 151 */ 152 struct udevice *eth_get_dev_by_name(const char *devname); 153 unsigned char *eth_get_ethaddr(void); /* get the current device MAC */ 154 155 /* Used only when NetConsole is enabled */ 156 int eth_is_active(struct udevice *dev); /* Test device for active state */ 157 int eth_init_state_only(void); /* Set active state */ 158 void eth_halt_state_only(void); /* Set passive state */ 159 #endif 160 161 #ifndef CONFIG_DM_ETH 162 struct eth_device { 163 char name[16]; 164 unsigned char enetaddr[6]; 165 phys_addr_t iobase; 166 int state; 167 168 int (*init)(struct eth_device *, bd_t *); 169 int (*send)(struct eth_device *, void *packet, int length); 170 int (*recv)(struct eth_device *); 171 void (*halt)(struct eth_device *); 172 #ifdef CONFIG_MCAST_TFTP 173 int (*mcast)(struct eth_device *, const u8 *enetaddr, u8 set); 174 #endif 175 int (*write_hwaddr)(struct eth_device *); 176 struct eth_device *next; 177 int index; 178 void *priv; 179 }; 180 181 int eth_register(struct eth_device *dev);/* Register network device */ 182 int eth_unregister(struct eth_device *dev);/* Remove network device */ 183 184 extern struct eth_device *eth_current; 185 186 static __always_inline struct eth_device *eth_get_dev(void) 187 { 188 return eth_current; 189 } 190 struct eth_device *eth_get_dev_by_name(const char *devname); 191 struct eth_device *eth_get_dev_by_index(int index); /* get dev @ index */ 192 193 /* get the current device MAC */ 194 static inline unsigned char *eth_get_ethaddr(void) 195 { 196 if (eth_current) 197 return eth_current->enetaddr; 198 return NULL; 199 } 200 201 /* Used only when NetConsole is enabled */ 202 int eth_is_active(struct eth_device *dev); /* Test device for active state */ 203 /* Set active state */ 204 static __always_inline int eth_init_state_only(void) 205 { 206 eth_get_dev()->state = ETH_STATE_ACTIVE; 207 208 return 0; 209 } 210 /* Set passive state */ 211 static __always_inline void eth_halt_state_only(void) 212 { 213 eth_get_dev()->state = ETH_STATE_PASSIVE; 214 } 215 216 /* 217 * Set the hardware address for an ethernet interface based on 'eth%daddr' 218 * environment variable (or just 'ethaddr' if eth_number is 0). 219 * Args: 220 * base_name - base name for device (normally "eth") 221 * eth_number - value of %d (0 for first device of this type) 222 * Returns: 223 * 0 is success, non-zero is error status from driver. 224 */ 225 int eth_write_hwaddr(struct eth_device *dev, const char *base_name, 226 int eth_number); 227 228 int usb_eth_initialize(bd_t *bi); 229 #endif 230 231 int eth_initialize(void); /* Initialize network subsystem */ 232 void eth_try_another(int first_restart); /* Change the device */ 233 void eth_set_current(void); /* set nterface to ethcur var */ 234 235 int eth_get_dev_index(void); /* get the device index */ 236 void eth_parse_enetaddr(const char *addr, uchar *enetaddr); 237 int eth_getenv_enetaddr(const char *name, uchar *enetaddr); 238 int eth_setenv_enetaddr(const char *name, const uchar *enetaddr); 239 240 /** 241 * eth_setenv_enetaddr_by_index() - set the MAC address environment variable 242 * 243 * This sets up an environment variable with the given MAC address (@enetaddr). 244 * The environment variable to be set is defined by <@base_name><@index>addr. 245 * If @index is 0 it is omitted. For common Ethernet this means ethaddr, 246 * eth1addr, etc. 247 * 248 * @base_name: Base name for variable, typically "eth" 249 * @index: Index of interface being updated (>=0) 250 * @enetaddr: Pointer to MAC address to put into the variable 251 * @return 0 if OK, other value on error 252 */ 253 int eth_setenv_enetaddr_by_index(const char *base_name, int index, 254 uchar *enetaddr); 255 256 257 /* 258 * Initialize USB ethernet device with CONFIG_DM_ETH 259 * Returns: 260 * 0 is success, non-zero is error status. 261 */ 262 int usb_ether_init(void); 263 264 /* 265 * Get the hardware address for an ethernet interface . 266 * Args: 267 * base_name - base name for device (normally "eth") 268 * index - device index number (0 for first) 269 * enetaddr - returns 6 byte hardware address 270 * Returns: 271 * Return true if the address is valid. 272 */ 273 int eth_getenv_enetaddr_by_index(const char *base_name, int index, 274 uchar *enetaddr); 275 276 int eth_init(void); /* Initialize the device */ 277 int eth_send(void *packet, int length); /* Send a packet */ 278 279 #if defined(CONFIG_API) || defined(CONFIG_EFI_LOADER) 280 int eth_receive(void *packet, int length); /* Receive a packet*/ 281 extern void (*push_packet)(void *packet, int length); 282 #endif 283 int eth_rx(void); /* Check for received packets */ 284 void eth_halt(void); /* stop SCC */ 285 const char *eth_get_name(void); /* get name of current device */ 286 287 #ifdef CONFIG_MCAST_TFTP 288 int eth_mcast_join(struct in_addr mcast_addr, int join); 289 u32 ether_crc(size_t len, unsigned char const *p); 290 #endif 291 292 293 /**********************************************************************/ 294 /* 295 * Protocol headers. 296 */ 297 298 /* 299 * Ethernet header 300 */ 301 302 struct ethernet_hdr { 303 u8 et_dest[6]; /* Destination node */ 304 u8 et_src[6]; /* Source node */ 305 u16 et_protlen; /* Protocol or length */ 306 }; 307 308 /* Ethernet header size */ 309 #define ETHER_HDR_SIZE (sizeof(struct ethernet_hdr)) 310 311 #define ETH_FCS_LEN 4 /* Octets in the FCS */ 312 313 struct e802_hdr { 314 u8 et_dest[6]; /* Destination node */ 315 u8 et_src[6]; /* Source node */ 316 u16 et_protlen; /* Protocol or length */ 317 u8 et_dsap; /* 802 DSAP */ 318 u8 et_ssap; /* 802 SSAP */ 319 u8 et_ctl; /* 802 control */ 320 u8 et_snap1; /* SNAP */ 321 u8 et_snap2; 322 u8 et_snap3; 323 u16 et_prot; /* 802 protocol */ 324 }; 325 326 /* 802 + SNAP + ethernet header size */ 327 #define E802_HDR_SIZE (sizeof(struct e802_hdr)) 328 329 /* 330 * Virtual LAN Ethernet header 331 */ 332 struct vlan_ethernet_hdr { 333 u8 vet_dest[6]; /* Destination node */ 334 u8 vet_src[6]; /* Source node */ 335 u16 vet_vlan_type; /* PROT_VLAN */ 336 u16 vet_tag; /* TAG of VLAN */ 337 u16 vet_type; /* protocol type */ 338 }; 339 340 /* VLAN Ethernet header size */ 341 #define VLAN_ETHER_HDR_SIZE (sizeof(struct vlan_ethernet_hdr)) 342 343 #define PROT_IP 0x0800 /* IP protocol */ 344 #define PROT_ARP 0x0806 /* IP ARP protocol */ 345 #define PROT_RARP 0x8035 /* IP ARP protocol */ 346 #define PROT_VLAN 0x8100 /* IEEE 802.1q protocol */ 347 #define PROT_IPV6 0x86dd /* IPv6 over bluebook */ 348 #define PROT_PPP_SES 0x8864 /* PPPoE session messages */ 349 350 #define IPPROTO_ICMP 1 /* Internet Control Message Protocol */ 351 #define IPPROTO_UDP 17 /* User Datagram Protocol */ 352 353 /* 354 * Internet Protocol (IP) header. 355 */ 356 struct ip_hdr { 357 u8 ip_hl_v; /* header length and version */ 358 u8 ip_tos; /* type of service */ 359 u16 ip_len; /* total length */ 360 u16 ip_id; /* identification */ 361 u16 ip_off; /* fragment offset field */ 362 u8 ip_ttl; /* time to live */ 363 u8 ip_p; /* protocol */ 364 u16 ip_sum; /* checksum */ 365 struct in_addr ip_src; /* Source IP address */ 366 struct in_addr ip_dst; /* Destination IP address */ 367 }; 368 369 #define IP_OFFS 0x1fff /* ip offset *= 8 */ 370 #define IP_FLAGS 0xe000 /* first 3 bits */ 371 #define IP_FLAGS_RES 0x8000 /* reserved */ 372 #define IP_FLAGS_DFRAG 0x4000 /* don't fragments */ 373 #define IP_FLAGS_MFRAG 0x2000 /* more fragments */ 374 375 #define IP_HDR_SIZE (sizeof(struct ip_hdr)) 376 377 /* 378 * Internet Protocol (IP) + UDP header. 379 */ 380 struct ip_udp_hdr { 381 u8 ip_hl_v; /* header length and version */ 382 u8 ip_tos; /* type of service */ 383 u16 ip_len; /* total length */ 384 u16 ip_id; /* identification */ 385 u16 ip_off; /* fragment offset field */ 386 u8 ip_ttl; /* time to live */ 387 u8 ip_p; /* protocol */ 388 u16 ip_sum; /* checksum */ 389 struct in_addr ip_src; /* Source IP address */ 390 struct in_addr ip_dst; /* Destination IP address */ 391 u16 udp_src; /* UDP source port */ 392 u16 udp_dst; /* UDP destination port */ 393 u16 udp_len; /* Length of UDP packet */ 394 u16 udp_xsum; /* Checksum */ 395 }; 396 397 #define IP_UDP_HDR_SIZE (sizeof(struct ip_udp_hdr)) 398 #define UDP_HDR_SIZE (IP_UDP_HDR_SIZE - IP_HDR_SIZE) 399 400 /* 401 * Address Resolution Protocol (ARP) header. 402 */ 403 struct arp_hdr { 404 u16 ar_hrd; /* Format of hardware address */ 405 # define ARP_ETHER 1 /* Ethernet hardware address */ 406 u16 ar_pro; /* Format of protocol address */ 407 u8 ar_hln; /* Length of hardware address */ 408 # define ARP_HLEN 6 409 u8 ar_pln; /* Length of protocol address */ 410 # define ARP_PLEN 4 411 u16 ar_op; /* Operation */ 412 # define ARPOP_REQUEST 1 /* Request to resolve address */ 413 # define ARPOP_REPLY 2 /* Response to previous request */ 414 415 # define RARPOP_REQUEST 3 /* Request to resolve address */ 416 # define RARPOP_REPLY 4 /* Response to previous request */ 417 418 /* 419 * The remaining fields are variable in size, according to 420 * the sizes above, and are defined as appropriate for 421 * specific hardware/protocol combinations. 422 */ 423 u8 ar_data[0]; 424 #define ar_sha ar_data[0] 425 #define ar_spa ar_data[ARP_HLEN] 426 #define ar_tha ar_data[ARP_HLEN + ARP_PLEN] 427 #define ar_tpa ar_data[ARP_HLEN + ARP_PLEN + ARP_HLEN] 428 #if 0 429 u8 ar_sha[]; /* Sender hardware address */ 430 u8 ar_spa[]; /* Sender protocol address */ 431 u8 ar_tha[]; /* Target hardware address */ 432 u8 ar_tpa[]; /* Target protocol address */ 433 #endif /* 0 */ 434 }; 435 436 #define ARP_HDR_SIZE (8+20) /* Size assuming ethernet */ 437 438 /* 439 * ICMP stuff (just enough to handle (host) redirect messages) 440 */ 441 #define ICMP_ECHO_REPLY 0 /* Echo reply */ 442 #define ICMP_NOT_REACH 3 /* Detination unreachable */ 443 #define ICMP_REDIRECT 5 /* Redirect (change route) */ 444 #define ICMP_ECHO_REQUEST 8 /* Echo request */ 445 446 /* Codes for REDIRECT. */ 447 #define ICMP_REDIR_NET 0 /* Redirect Net */ 448 #define ICMP_REDIR_HOST 1 /* Redirect Host */ 449 450 /* Codes for NOT_REACH */ 451 #define ICMP_NOT_REACH_PORT 3 /* Port unreachable */ 452 453 struct icmp_hdr { 454 u8 type; 455 u8 code; 456 u16 checksum; 457 union { 458 struct { 459 u16 id; 460 u16 sequence; 461 } echo; 462 u32 gateway; 463 struct { 464 u16 unused; 465 u16 mtu; 466 } frag; 467 u8 data[0]; 468 } un; 469 }; 470 471 #define ICMP_HDR_SIZE (sizeof(struct icmp_hdr)) 472 #define IP_ICMP_HDR_SIZE (IP_HDR_SIZE + ICMP_HDR_SIZE) 473 474 /* 475 * Maximum packet size; used to allocate packet storage. Use 476 * the maxium Ethernet frame size as specified by the Ethernet 477 * standard including the 802.1Q tag (VLAN tagging). 478 * maximum packet size = 1522 479 * maximum packet size and multiple of 32 bytes = 1536 480 */ 481 #define PKTSIZE 1522 482 #define PKTSIZE_ALIGN 1536 483 484 /* 485 * Maximum receive ring size; that is, the number of packets 486 * we can buffer before overflow happens. Basically, this just 487 * needs to be enough to prevent a packet being discarded while 488 * we are processing the previous one. 489 */ 490 #define RINGSZ 4 491 #define RINGSZ_LOG2 2 492 493 /**********************************************************************/ 494 /* 495 * Globals. 496 * 497 * Note: 498 * 499 * All variables of type struct in_addr are stored in NETWORK byte order 500 * (big endian). 501 */ 502 503 /* net.c */ 504 /** BOOTP EXTENTIONS **/ 505 extern struct in_addr net_gateway; /* Our gateway IP address */ 506 extern struct in_addr net_netmask; /* Our subnet mask (0 = unknown) */ 507 /* Our Domain Name Server (0 = unknown) */ 508 extern struct in_addr net_dns_server; 509 #if defined(CONFIG_BOOTP_DNS2) 510 /* Our 2nd Domain Name Server (0 = unknown) */ 511 extern struct in_addr net_dns_server2; 512 #endif 513 extern char net_nis_domain[32]; /* Our IS domain */ 514 extern char net_hostname[32]; /* Our hostname */ 515 extern char net_root_path[64]; /* Our root path */ 516 /** END OF BOOTP EXTENTIONS **/ 517 extern u8 net_ethaddr[6]; /* Our ethernet address */ 518 extern u8 net_server_ethaddr[6]; /* Boot server enet address */ 519 extern struct in_addr net_ip; /* Our IP addr (0 = unknown) */ 520 extern struct in_addr net_server_ip; /* Server IP addr (0 = unknown) */ 521 extern uchar *net_tx_packet; /* THE transmit packet */ 522 extern uchar *net_rx_packets[PKTBUFSRX]; /* Receive packets */ 523 extern uchar *net_rx_packet; /* Current receive packet */ 524 extern int net_rx_packet_len; /* Current rx packet length */ 525 extern const u8 net_bcast_ethaddr[6]; /* Ethernet broadcast address */ 526 extern const u8 net_null_ethaddr[6]; 527 528 #define VLAN_NONE 4095 /* untagged */ 529 #define VLAN_IDMASK 0x0fff /* mask of valid vlan id */ 530 extern ushort net_our_vlan; /* Our VLAN */ 531 extern ushort net_native_vlan; /* Our Native VLAN */ 532 533 extern int net_restart_wrap; /* Tried all network devices */ 534 535 enum proto_t { 536 BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP, 537 TFTPSRV, TFTPPUT, LINKLOCAL 538 }; 539 540 extern char net_boot_file_name[1024];/* Boot File name */ 541 /* The actual transferred size of the bootfile (in bytes) */ 542 extern u32 net_boot_file_size; 543 /* Boot file size in blocks as reported by the DHCP server */ 544 extern u32 net_boot_file_expected_size_in_blocks; 545 546 #if defined(CONFIG_CMD_DNS) 547 extern char *net_dns_resolve; /* The host to resolve */ 548 extern char *net_dns_env_var; /* the env var to put the ip into */ 549 #endif 550 551 #if defined(CONFIG_CMD_PING) 552 extern struct in_addr net_ping_ip; /* the ip address to ping */ 553 #endif 554 555 #if defined(CONFIG_CMD_CDP) 556 /* when CDP completes these hold the return values */ 557 extern ushort cdp_native_vlan; /* CDP returned native VLAN */ 558 extern ushort cdp_appliance_vlan; /* CDP returned appliance VLAN */ 559 560 /* 561 * Check for a CDP packet by examining the received MAC address field 562 */ 563 static inline int is_cdp_packet(const uchar *ethaddr) 564 { 565 extern const u8 net_cdp_ethaddr[6]; 566 567 return memcmp(ethaddr, net_cdp_ethaddr, 6) == 0; 568 } 569 #endif 570 571 #if defined(CONFIG_CMD_SNTP) 572 extern struct in_addr net_ntp_server; /* the ip address to NTP */ 573 extern int net_ntp_time_offset; /* offset time from UTC */ 574 #endif 575 576 #if defined(CONFIG_MCAST_TFTP) 577 extern struct in_addr net_mcast_addr; 578 #endif 579 580 /* Initialize the network adapter */ 581 void net_init(void); 582 int net_loop(enum proto_t); 583 584 /* Load failed. Start again. */ 585 int net_start_again(void); 586 587 /* Get size of the ethernet header when we send */ 588 int net_eth_hdr_size(void); 589 590 /* Set ethernet header; returns the size of the header */ 591 int net_set_ether(uchar *xet, const uchar *dest_ethaddr, uint prot); 592 int net_update_ether(struct ethernet_hdr *et, uchar *addr, uint prot); 593 594 /* Set IP header */ 595 void net_set_ip_header(uchar *pkt, struct in_addr dest, struct in_addr source); 596 void net_set_udp_header(uchar *pkt, struct in_addr dest, int dport, 597 int sport, int len); 598 599 /** 600 * compute_ip_checksum() - Compute IP checksum 601 * 602 * @addr: Address to check (must be 16-bit aligned) 603 * @nbytes: Number of bytes to check (normally a multiple of 2) 604 * @return 16-bit IP checksum 605 */ 606 unsigned compute_ip_checksum(const void *addr, unsigned nbytes); 607 608 /** 609 * add_ip_checksums() - add two IP checksums 610 * 611 * @offset: Offset of first sum (if odd we do a byte-swap) 612 * @sum: First checksum 613 * @new_sum: New checksum to add 614 * @return updated 16-bit IP checksum 615 */ 616 unsigned add_ip_checksums(unsigned offset, unsigned sum, unsigned new_sum); 617 618 /** 619 * ip_checksum_ok() - check if a checksum is correct 620 * 621 * This works by making sure the checksum sums to 0 622 * 623 * @addr: Address to check (must be 16-bit aligned) 624 * @nbytes: Number of bytes to check (normally a multiple of 2) 625 * @return true if the checksum matches, false if not 626 */ 627 int ip_checksum_ok(const void *addr, unsigned nbytes); 628 629 /* Callbacks */ 630 rxhand_f *net_get_udp_handler(void); /* Get UDP RX packet handler */ 631 void net_set_udp_handler(rxhand_f *); /* Set UDP RX packet handler */ 632 rxhand_f *net_get_arp_handler(void); /* Get ARP RX packet handler */ 633 void net_set_arp_handler(rxhand_f *); /* Set ARP RX packet handler */ 634 void net_set_icmp_handler(rxhand_icmp_f *f); /* Set ICMP RX handler */ 635 void net_set_timeout_handler(ulong, thand_f *);/* Set timeout handler */ 636 637 /* Network loop state */ 638 enum net_loop_state { 639 NETLOOP_CONTINUE, 640 NETLOOP_RESTART, 641 NETLOOP_SUCCESS, 642 NETLOOP_FAIL 643 }; 644 extern enum net_loop_state net_state; 645 646 static inline void net_set_state(enum net_loop_state state) 647 { 648 debug_cond(DEBUG_INT_STATE, "--- NetState set to %d\n", state); 649 net_state = state; 650 } 651 652 /* Transmit a packet */ 653 static inline void net_send_packet(uchar *pkt, int len) 654 { 655 /* Currently no way to return errors from eth_send() */ 656 (void) eth_send(pkt, len); 657 } 658 659 /* 660 * Transmit "net_tx_packet" as UDP packet, performing ARP request if needed 661 * (ether will be populated) 662 * 663 * @param ether Raw packet buffer 664 * @param dest IP address to send the datagram to 665 * @param dport Destination UDP port 666 * @param sport Source UDP port 667 * @param payload_len Length of data after the UDP header 668 */ 669 int net_send_udp_packet(uchar *ether, struct in_addr dest, int dport, 670 int sport, int payload_len); 671 672 /* Processes a received packet */ 673 void net_process_received_packet(uchar *in_packet, int len); 674 675 #ifdef CONFIG_NETCONSOLE 676 void nc_start(void); 677 int nc_input_packet(uchar *pkt, struct in_addr src_ip, unsigned dest_port, 678 unsigned src_port, unsigned len); 679 #endif 680 681 static __always_inline int eth_is_on_demand_init(void) 682 { 683 #ifdef CONFIG_NETCONSOLE 684 extern enum proto_t net_loop_last_protocol; 685 686 return net_loop_last_protocol != NETCONS; 687 #else 688 return 1; 689 #endif 690 } 691 692 static inline void eth_set_last_protocol(int protocol) 693 { 694 #ifdef CONFIG_NETCONSOLE 695 extern enum proto_t net_loop_last_protocol; 696 697 net_loop_last_protocol = protocol; 698 #endif 699 } 700 701 /* 702 * Check if autoload is enabled. If so, use either NFS or TFTP to download 703 * the boot file. 704 */ 705 void net_auto_load(void); 706 707 /* 708 * The following functions are a bit ugly, but necessary to deal with 709 * alignment restrictions on ARM. 710 * 711 * We're using inline functions, which had the smallest memory 712 * footprint in our tests. 713 */ 714 /* return IP *in network byteorder* */ 715 static inline struct in_addr net_read_ip(void *from) 716 { 717 struct in_addr ip; 718 719 memcpy((void *)&ip, (void *)from, sizeof(ip)); 720 return ip; 721 } 722 723 /* return ulong *in network byteorder* */ 724 static inline u32 net_read_u32(u32 *from) 725 { 726 u32 l; 727 728 memcpy((void *)&l, (void *)from, sizeof(l)); 729 return l; 730 } 731 732 /* write IP *in network byteorder* */ 733 static inline void net_write_ip(void *to, struct in_addr ip) 734 { 735 memcpy(to, (void *)&ip, sizeof(ip)); 736 } 737 738 /* copy IP */ 739 static inline void net_copy_ip(void *to, void *from) 740 { 741 memcpy((void *)to, from, sizeof(struct in_addr)); 742 } 743 744 /* copy ulong */ 745 static inline void net_copy_u32(u32 *to, u32 *from) 746 { 747 memcpy((void *)to, (void *)from, sizeof(u32)); 748 } 749 750 /** 751 * is_zero_ethaddr - Determine if give Ethernet address is all zeros. 752 * @addr: Pointer to a six-byte array containing the Ethernet address 753 * 754 * Return true if the address is all zeroes. 755 */ 756 static inline int is_zero_ethaddr(const u8 *addr) 757 { 758 return !(addr[0] | addr[1] | addr[2] | addr[3] | addr[4] | addr[5]); 759 } 760 761 /** 762 * is_multicast_ethaddr - Determine if the Ethernet address is a multicast. 763 * @addr: Pointer to a six-byte array containing the Ethernet address 764 * 765 * Return true if the address is a multicast address. 766 * By definition the broadcast address is also a multicast address. 767 */ 768 static inline int is_multicast_ethaddr(const u8 *addr) 769 { 770 return 0x01 & addr[0]; 771 } 772 773 /* 774 * is_broadcast_ethaddr - Determine if the Ethernet address is broadcast 775 * @addr: Pointer to a six-byte array containing the Ethernet address 776 * 777 * Return true if the address is the broadcast address. 778 */ 779 static inline int is_broadcast_ethaddr(const u8 *addr) 780 { 781 return (addr[0] & addr[1] & addr[2] & addr[3] & addr[4] & addr[5]) == 782 0xff; 783 } 784 785 /* 786 * is_valid_ethaddr - Determine if the given Ethernet address is valid 787 * @addr: Pointer to a six-byte array containing the Ethernet address 788 * 789 * Check that the Ethernet address (MAC) is not 00:00:00:00:00:00, is not 790 * a multicast address, and is not FF:FF:FF:FF:FF:FF. 791 * 792 * Return true if the address is valid. 793 */ 794 static inline int is_valid_ethaddr(const u8 *addr) 795 { 796 /* FF:FF:FF:FF:FF:FF is a multicast address so we don't need to 797 * explicitly check for it here. */ 798 return !is_multicast_ethaddr(addr) && !is_zero_ethaddr(addr); 799 } 800 801 /** 802 * net_random_ethaddr - Generate software assigned random Ethernet address 803 * @addr: Pointer to a six-byte array containing the Ethernet address 804 * 805 * Generate a random Ethernet address (MAC) that is not multicast 806 * and has the local assigned bit set. 807 */ 808 static inline void net_random_ethaddr(uchar *addr) 809 { 810 int i; 811 unsigned int seed = get_timer(0); 812 813 for (i = 0; i < 6; i++) 814 addr[i] = rand_r(&seed); 815 816 addr[0] &= 0xfe; /* clear multicast bit */ 817 addr[0] |= 0x02; /* set local assignment bit (IEEE802) */ 818 } 819 820 /* Convert an IP address to a string */ 821 void ip_to_string(struct in_addr x, char *s); 822 823 /* Convert a string to ip address */ 824 struct in_addr string_to_ip(const char *s); 825 826 /* Convert a VLAN id to a string */ 827 void vlan_to_string(ushort x, char *s); 828 829 /* Convert a string to a vlan id */ 830 ushort string_to_vlan(const char *s); 831 832 /* read a VLAN id from an environment variable */ 833 ushort getenv_vlan(char *); 834 835 /* copy a filename (allow for "..." notation, limit length) */ 836 void copy_filename(char *dst, const char *src, int size); 837 838 /* get a random source port */ 839 unsigned int random_port(void); 840 841 /** 842 * update_tftp - Update firmware over TFTP (via DFU) 843 * 844 * This function updates board's firmware via TFTP 845 * 846 * @param addr - memory address where data is stored 847 * @param interface - the DFU medium name - e.g. "mmc" 848 * @param devstring - the DFU medium number - e.g. "1" 849 * 850 * @return - 0 on success, other value on failure 851 */ 852 int update_tftp(ulong addr, char *interface, char *devstring); 853 854 /**********************************************************************/ 855 856 #endif /* __NET_H__ */ 857