1 /* 2 * (C) Copyright 2009 3 * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef ST_SMI_H 9 #define ST_SMI_H 10 11 /* 0xF800.0000 . 0xFBFF.FFFF 64MB SMI (Serial Flash Mem) */ 12 /* 0xFC00.0000 . 0xFC1F.FFFF 2MB SMI (Serial Flash Reg.) */ 13 14 #define FLASH_START_ADDRESS CONFIG_SYS_FLASH_BASE 15 #define FLASH_BANK_SIZE CONFIG_SYS_FLASH_BANK_SIZE 16 17 #define SMIBANK0_BASE (FLASH_START_ADDRESS) 18 #define SMIBANK1_BASE (SMIBANK0_BASE + FLASH_BANK_SIZE) 19 #define SMIBANK2_BASE (SMIBANK1_BASE + FLASH_BANK_SIZE) 20 #define SMIBANK3_BASE (SMIBANK2_BASE + FLASH_BANK_SIZE) 21 22 #define BANK0 0 23 #define BANK1 1 24 #define BANK2 2 25 #define BANK3 3 26 27 struct smi_regs { 28 u32 smi_cr1; 29 u32 smi_cr2; 30 u32 smi_sr; 31 u32 smi_tr; 32 u32 smi_rr; 33 }; 34 35 /* CONTROL REG 1 */ 36 #define BANK_EN 0x0000000F /* enables all banks */ 37 #define DSEL_TIME 0x00000060 /* Deselect time */ 38 #define PRESCAL5 0x00000500 /* AHB_CK prescaling value */ 39 #define PRESCALA 0x00000A00 /* AHB_CK prescaling value */ 40 #define PRESCAL3 0x00000300 /* AHB_CK prescaling value */ 41 #define PRESCAL4 0x00000400 /* AHB_CK prescaling value */ 42 #define SW_MODE 0x10000000 /* enables SW Mode */ 43 #define WB_MODE 0x20000000 /* Write Burst Mode */ 44 #define FAST_MODE 0x00008000 /* Fast Mode */ 45 #define HOLD1 0x00010000 46 47 /* CONTROL REG 2 */ 48 #define RD_STATUS_REG 0x00000400 /* reads status reg */ 49 #define WE 0x00000800 /* Write Enable */ 50 #define BANK0_SEL 0x00000000 /* Select Banck0 */ 51 #define BANK1_SEL 0x00001000 /* Select Banck1 */ 52 #define BANK2_SEL 0x00002000 /* Select Banck2 */ 53 #define BANK3_SEL 0x00003000 /* Select Banck3 */ 54 #define BANKSEL_SHIFT 12 55 #define SEND 0x00000080 /* Send data */ 56 #define TX_LEN_1 0x00000001 /* data length = 1 byte */ 57 #define TX_LEN_2 0x00000002 /* data length = 2 byte */ 58 #define TX_LEN_3 0x00000003 /* data length = 3 byte */ 59 #define TX_LEN_4 0x00000004 /* data length = 4 byte */ 60 #define RX_LEN_1 0x00000010 /* data length = 1 byte */ 61 #define RX_LEN_2 0x00000020 /* data length = 2 byte */ 62 #define RX_LEN_3 0x00000030 /* data length = 3 byte */ 63 #define RX_LEN_4 0x00000040 /* data length = 4 byte */ 64 #define TFIE 0x00000100 /* Tx Flag Interrupt Enable */ 65 #define WCIE 0x00000200 /* WCF Interrupt Enable */ 66 67 /* STATUS_REG */ 68 #define INT_WCF_CLR 0xFFFFFDFF /* clear: WCF clear */ 69 #define INT_TFF_CLR 0xFFFFFEFF /* clear: TFF clear */ 70 #define WIP_BIT 0x00000001 /* WIP Bit of SPI SR */ 71 #define WEL_BIT 0x00000002 /* WEL Bit of SPI SR */ 72 #define RSR 0x00000005 /* Read Status regiser */ 73 #define TFF 0x00000100 /* Transfer Finished FLag */ 74 #define WCF 0x00000200 /* Transfer Finished FLag */ 75 #define ERF1 0x00000400 /* Error Flag 1 */ 76 #define ERF2 0x00000800 /* Error Flag 2 */ 77 #define WM0 0x00001000 /* WM Bank 0 */ 78 #define WM1 0x00002000 /* WM Bank 1 */ 79 #define WM2 0x00004000 /* WM Bank 2 */ 80 #define WM3 0x00008000 /* WM Bank 3 */ 81 #define WM_SHIFT 12 82 83 /* TR REG */ 84 #define READ_ID 0x0000009F /* Read Identification */ 85 #define BULK_ERASE 0x000000C7 /* BULK erase */ 86 #define SECTOR_ERASE 0x000000D8 /* SECTOR erase */ 87 #define WRITE_ENABLE 0x00000006 /* Wenable command to FLASH */ 88 89 struct flash_dev { 90 u32 density; 91 ulong size; 92 ushort sector_count; 93 }; 94 95 #define SFLASH_PAGE_SIZE 0x100 /* flash page size */ 96 #define XFER_FINISH_TOUT 15 /* xfer finish timeout(in ms) */ 97 #define WMODE_TOUT 15 /* write enable timeout(in ms) */ 98 99 extern void smi_init(void); 100 101 #endif 102