1 /* 2 * (C) Copyright 2012 Michal Simek <monstr@monstr.eu> 3 * (C) Copyright 2013 Xilinx, Inc. 4 * 5 * Common configuration options for all Zynq boards. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_ZYNQ_COMMON_H 11 #define __CONFIG_ZYNQ_COMMON_H 12 13 /* CPU clock */ 14 #ifndef CONFIG_CPU_FREQ_HZ 15 # define CONFIG_CPU_FREQ_HZ 800000000 16 #endif 17 18 /* Cache options */ 19 #define CONFIG_SYS_L2CACHE_OFF 20 #ifndef CONFIG_SYS_L2CACHE_OFF 21 # define CONFIG_SYS_L2_PL310 22 # define CONFIG_SYS_PL310_BASE 0xf8f02000 23 #endif 24 25 #define ZYNQ_SCUTIMER_BASEADDR 0xF8F00600 26 #define CONFIG_SYS_TIMERBASE ZYNQ_SCUTIMER_BASEADDR 27 #define CONFIG_SYS_TIMER_COUNTS_DOWN 28 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) 29 30 /* Serial drivers */ 31 #define CONFIG_BAUDRATE 115200 32 /* The following table includes the supported baudrates */ 33 #define CONFIG_SYS_BAUDRATE_TABLE \ 34 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} 35 36 #define CONFIG_ARM_DCC 37 #define CONFIG_ZYNQ_SERIAL 38 39 /* Ethernet driver */ 40 #if defined(CONFIG_ZYNQ_GEM) 41 # define CONFIG_MII 42 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 43 # define CONFIG_PHY_MARVELL 44 # define CONFIG_PHY_REALTEK 45 # define CONFIG_PHY_XILINX 46 # define CONFIG_BOOTP_SERVERIP 47 # define CONFIG_BOOTP_BOOTPATH 48 # define CONFIG_BOOTP_GATEWAY 49 # define CONFIG_BOOTP_HOSTNAME 50 # define CONFIG_BOOTP_MAY_FAIL 51 #endif 52 53 /* SPI */ 54 #ifdef CONFIG_ZYNQ_SPI 55 #endif 56 57 /* QSPI */ 58 #ifdef CONFIG_ZYNQ_QSPI 59 # define CONFIG_SF_DEFAULT_SPEED 30000000 60 # define CONFIG_SPI_FLASH_ISSI 61 #endif 62 63 /* NOR */ 64 #ifndef CONFIG_SYS_NO_FLASH 65 # define CONFIG_SYS_FLASH_BASE 0xE2000000 66 # define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024) 67 # define CONFIG_SYS_MAX_FLASH_BANKS 1 68 # define CONFIG_SYS_MAX_FLASH_SECT 512 69 # define CONFIG_SYS_FLASH_ERASE_TOUT 1000 70 # define CONFIG_SYS_FLASH_WRITE_TOUT 5000 71 # define CONFIG_FLASH_SHOW_PROGRESS 10 72 # define CONFIG_SYS_FLASH_CFI 73 # undef CONFIG_SYS_FLASH_EMPTY_INFO 74 # define CONFIG_FLASH_CFI_DRIVER 75 # undef CONFIG_SYS_FLASH_PROTECTION 76 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 77 #endif 78 79 /* MMC */ 80 #if defined(CONFIG_ZYNQ_SDHCI) 81 # define CONFIG_MMC 82 # define CONFIG_GENERIC_MMC 83 # define CONFIG_SDHCI 84 # define CONFIG_ZYNQ_SDHCI_MAX_FREQ 52000000 85 #endif 86 87 #ifdef CONFIG_USB_EHCI_ZYNQ 88 # define CONFIG_EHCI_IS_TDI 89 # define CONFIG_USB_MAX_CONTROLLER_COUNT 2 90 91 # define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000 92 # define DFU_DEFAULT_POLL_TIMEOUT 300 93 # define CONFIG_USB_CABLE_CHECK 94 # define CONFIG_CMD_THOR_DOWNLOAD 95 # define CONFIG_THOR_RESET_OFF 96 # define CONFIG_USB_FUNCTION_THOR 97 # define DFU_ALT_INFO_RAM \ 98 "dfu_ram_info=" \ 99 "set dfu_alt_info " \ 100 "${kernel_image} ram 0x3000000 0x500000\\\\;" \ 101 "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \ 102 "${ramdisk_image} ram 0x2000000 0x600000\0" \ 103 "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \ 104 "thor_ram=run dfu_ram_info && thordown 0 ram 0\0" 105 106 # if defined(CONFIG_ZYNQ_SDHCI) 107 # define DFU_ALT_INFO_MMC \ 108 "dfu_mmc_info=" \ 109 "set dfu_alt_info " \ 110 "${kernel_image} fat 0 1\\\\;" \ 111 "${devicetree_image} fat 0 1\\\\;" \ 112 "${ramdisk_image} fat 0 1\0" \ 113 "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \ 114 "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0" 115 116 # define DFU_ALT_INFO \ 117 DFU_ALT_INFO_RAM \ 118 DFU_ALT_INFO_MMC 119 # else 120 # define DFU_ALT_INFO \ 121 DFU_ALT_INFO_RAM 122 # endif 123 #endif 124 125 #if !defined(DFU_ALT_INFO) 126 # define DFU_ALT_INFO 127 #endif 128 129 #if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB) 130 # define CONFIG_SUPPORT_VFAT 131 # define CONFIG_FAT_WRITE 132 # define CONFIG_DOS_PARTITION 133 #endif 134 135 #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1) 136 #define CONFIG_SYS_I2C_ZYNQ 137 #endif 138 139 /* I2C */ 140 #if defined(CONFIG_SYS_I2C_ZYNQ) 141 # define CONFIG_SYS_I2C 142 # define CONFIG_SYS_I2C_ZYNQ_SPEED 100000 143 # define CONFIG_SYS_I2C_ZYNQ_SLAVE 0 144 #endif 145 146 /* EEPROM */ 147 #ifdef CONFIG_ZYNQ_EEPROM 148 # define CONFIG_CMD_EEPROM 149 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 150 # define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 151 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 152 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 153 # define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */ 154 #endif 155 156 /* Total Size of Environment Sector */ 157 #define CONFIG_ENV_SIZE (128 << 10) 158 159 /* Allow to overwrite serial and ethaddr */ 160 #define CONFIG_ENV_OVERWRITE 161 162 /* Environment */ 163 #ifndef CONFIG_ENV_IS_NOWHERE 164 # ifndef CONFIG_SYS_NO_FLASH 165 /* Environment in NOR flash */ 166 # define CONFIG_ENV_IS_IN_FLASH 167 # elif defined(CONFIG_ZYNQ_QSPI) 168 /* Environment in Serial Flash */ 169 # define CONFIG_ENV_IS_IN_SPI_FLASH 170 # elif defined(CONFIG_SYS_NO_FLASH) 171 # define CONFIG_ENV_IS_NOWHERE 172 # endif 173 174 # define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE 175 # define CONFIG_ENV_OFFSET 0xE0000 176 #endif 177 178 /* enable preboot to be loaded before CONFIG_BOOTDELAY */ 179 #define CONFIG_PREBOOT 180 181 /* Default environment */ 182 #ifndef CONFIG_EXTRA_ENV_SETTINGS 183 #define CONFIG_EXTRA_ENV_SETTINGS \ 184 "fit_image=fit.itb\0" \ 185 "load_addr=0x2000000\0" \ 186 "fit_size=0x800000\0" \ 187 "flash_off=0x100000\0" \ 188 "nor_flash_off=0xE2100000\0" \ 189 "fdt_high=0x20000000\0" \ 190 "initrd_high=0x20000000\0" \ 191 "loadbootenv_addr=0x2000000\0" \ 192 "bootenv=uEnv.txt\0" \ 193 "bootenv_dev=mmc\0" \ 194 "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \ 195 "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \ 196 "env import -t ${loadbootenv_addr} $filesize\0" \ 197 "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \ 198 "setbootenv=if env run bootenv_existence_test; then " \ 199 "if env run loadbootenv; then " \ 200 "env run importbootenv; " \ 201 "fi; " \ 202 "fi; \0" \ 203 "sd_loadbootenv=set bootenv_dev mmc && " \ 204 "run setbootenv \0" \ 205 "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \ 206 "preboot=if test $modeboot = sdboot; then " \ 207 "run sd_loadbootenv; " \ 208 "echo Checking if uenvcmd is set ...; " \ 209 "if test -n $uenvcmd; then " \ 210 "echo Running uenvcmd ...; " \ 211 "run uenvcmd; " \ 212 "fi; " \ 213 "fi; \0" \ 214 "norboot=echo Copying FIT from NOR flash to RAM... && " \ 215 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \ 216 "bootm ${load_addr}\0" \ 217 "sdboot=echo Copying FIT from SD to RAM... && " \ 218 "load mmc 0 ${load_addr} ${fit_image} && " \ 219 "bootm ${load_addr}\0" \ 220 "jtagboot=echo TFTPing FIT to RAM... && " \ 221 "tftpboot ${load_addr} ${fit_image} && " \ 222 "bootm ${load_addr}\0" \ 223 "usbboot=if usb start; then " \ 224 "echo Copying FIT from USB to RAM... && " \ 225 "load usb 0 ${load_addr} ${fit_image} && " \ 226 "bootm ${load_addr}; fi\0" \ 227 DFU_ALT_INFO 228 #endif 229 230 #define CONFIG_BOOTCOMMAND "run $modeboot" 231 #define CONFIG_SYS_LOAD_ADDR 0 /* default? */ 232 233 /* Miscellaneous configurable options */ 234 235 #define CONFIG_CMDLINE_EDITING 236 #define CONFIG_AUTO_COMPLETE 237 #define CONFIG_BOARD_LATE_INIT 238 #define CONFIG_DISPLAY_BOARDINFO 239 #define CONFIG_SYS_LONGHELP 240 #define CONFIG_CLOCKS 241 #define CONFIG_CMD_CLK 242 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 243 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 244 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 245 sizeof(CONFIG_SYS_PROMPT) + 16) 246 247 /* Physical Memory map */ 248 #define CONFIG_SYS_TEXT_BASE 0x4000000 249 250 #ifndef CONFIG_NR_DRAM_BANKS 251 # define CONFIG_NR_DRAM_BANKS 1 252 #endif 253 254 #define CONFIG_SYS_MEMTEST_START 0 255 #define CONFIG_SYS_MEMTEST_END 0x1000 256 257 #define CONFIG_SYS_MALLOC_LEN 0x1400000 258 259 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 260 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 261 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 262 CONFIG_SYS_INIT_RAM_SIZE - \ 263 GENERATED_GBL_DATA_SIZE) 264 265 /* Enable the PL to be downloaded */ 266 #define CONFIG_FPGA 267 #define CONFIG_FPGA_XILINX 268 #define CONFIG_FPGA_ZYNQPL 269 #define CONFIG_CMD_FPGA_LOADMK 270 #define CONFIG_CMD_FPGA_LOADP 271 #define CONFIG_CMD_FPGA_LOADBP 272 #define CONFIG_CMD_FPGA_LOADFS 273 274 /* FIT support */ 275 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */ 276 277 /* FDT support */ 278 #define CONFIG_DISPLAY_BOARDINFO_LATE 279 280 /* Extend size of kernel image for uncompression */ 281 #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024) 282 283 /* Boot FreeBSD/vxWorks from an ELF image */ 284 #define CONFIG_SYS_MMC_MAX_DEVICE 1 285 286 #define CONFIG_SYS_LDSCRIPT "arch/arm/mach-zynq/u-boot.lds" 287 288 /* Commands */ 289 290 /* SPL part */ 291 #define CONFIG_CMD_SPL 292 #define CONFIG_SPL_FRAMEWORK 293 #define CONFIG_SPL_BOARD_INIT 294 #define CONFIG_SPL_RAM_DEVICE 295 296 #define CONFIG_SPL_LDSCRIPT "arch/arm/mach-zynq/u-boot-spl.lds" 297 298 /* MMC support */ 299 #ifdef CONFIG_ZYNQ_SDHCI 300 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ 301 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ 302 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 303 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 304 #endif 305 306 /* Disable dcache for SPL just for sure */ 307 #ifdef CONFIG_SPL_BUILD 308 #define CONFIG_SYS_DCACHE_OFF 309 #undef CONFIG_FPGA 310 #endif 311 312 /* Address in RAM where the parameters must be copied by SPL. */ 313 #define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000 314 315 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb" 316 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 317 318 /* Not using MMC raw mode - just for compilation purpose */ 319 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 320 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 321 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 322 323 /* qspi mode is working fine */ 324 #ifdef CONFIG_ZYNQ_QSPI 325 #define CONFIG_SPL_SPI_LOAD 326 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000 327 #define CONFIG_SYS_SPI_ARGS_OFFS 0x200000 328 #define CONFIG_SYS_SPI_ARGS_SIZE 0x80000 329 #define CONFIG_SYS_SPI_KERNEL_OFFS (CONFIG_SYS_SPI_ARGS_OFFS + \ 330 CONFIG_SYS_SPI_ARGS_SIZE) 331 #endif 332 333 /* for booting directly linux */ 334 #define CONFIG_SPL_OS_BOOT 335 336 /* SP location before relocation, must use scratch RAM */ 337 #define CONFIG_SPL_TEXT_BASE 0x0 338 339 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */ 340 #define CONFIG_SPL_MAX_SIZE 0x30000 341 342 /* The highest 64k OCM address */ 343 #define OCM_HIGH_ADDR 0xffff0000 344 345 /* On the top of OCM space */ 346 #define CONFIG_SYS_SPL_MALLOC_START OCM_HIGH_ADDR 347 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000 348 349 /* 350 * SPL stack position - and stack goes down 351 * 0xfffffe00 is used for putting wfi loop. 352 * Set it up as limit for now. 353 */ 354 #define CONFIG_SPL_STACK 0xfffffe00 355 356 /* BSS setup */ 357 #define CONFIG_SPL_BSS_START_ADDR 0x100000 358 #define CONFIG_SPL_BSS_MAX_SIZE 0x100000 359 360 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 361 362 #endif /* __CONFIG_ZYNQ_COMMON_H */ 363