1 /* 2 * (C) Copyright 2012 Michal Simek <monstr@monstr.eu> 3 * (C) Copyright 2013 Xilinx, Inc. 4 * 5 * Common configuration options for all Zynq boards. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_ZYNQ_COMMON_H 11 #define __CONFIG_ZYNQ_COMMON_H 12 13 /* CPU clock */ 14 #ifndef CONFIG_CPU_FREQ_HZ 15 # define CONFIG_CPU_FREQ_HZ 800000000 16 #endif 17 18 /* Cache options */ 19 #define CONFIG_SYS_L2CACHE_OFF 20 #ifndef CONFIG_SYS_L2CACHE_OFF 21 # define CONFIG_SYS_L2_PL310 22 # define CONFIG_SYS_PL310_BASE 0xf8f02000 23 #endif 24 25 #define ZYNQ_SCUTIMER_BASEADDR 0xF8F00600 26 #define CONFIG_SYS_TIMERBASE ZYNQ_SCUTIMER_BASEADDR 27 #define CONFIG_SYS_TIMER_COUNTS_DOWN 28 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) 29 30 /* Serial drivers */ 31 #define CONFIG_BAUDRATE 115200 32 /* The following table includes the supported baudrates */ 33 #define CONFIG_SYS_BAUDRATE_TABLE \ 34 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} 35 36 #define CONFIG_ARM_DCC 37 #define CONFIG_ZYNQ_SERIAL 38 39 /* Ethernet driver */ 40 #if defined(CONFIG_ZYNQ_GEM) 41 # define CONFIG_MII 42 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 43 # define CONFIG_PHY_MARVELL 44 # define CONFIG_PHY_REALTEK 45 # define CONFIG_PHY_XILINX 46 # define CONFIG_BOOTP_BOOTPATH 47 # define CONFIG_BOOTP_GATEWAY 48 # define CONFIG_BOOTP_HOSTNAME 49 # define CONFIG_BOOTP_MAY_FAIL 50 #endif 51 52 /* SPI */ 53 #ifdef CONFIG_ZYNQ_SPI 54 #endif 55 56 /* QSPI */ 57 #ifdef CONFIG_ZYNQ_QSPI 58 # define CONFIG_SF_DEFAULT_SPEED 30000000 59 # define CONFIG_SPI_FLASH_ISSI 60 #endif 61 62 /* NOR */ 63 #ifndef CONFIG_SYS_NO_FLASH 64 # define CONFIG_SYS_FLASH_BASE 0xE2000000 65 # define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024) 66 # define CONFIG_SYS_MAX_FLASH_BANKS 1 67 # define CONFIG_SYS_MAX_FLASH_SECT 512 68 # define CONFIG_SYS_FLASH_ERASE_TOUT 1000 69 # define CONFIG_SYS_FLASH_WRITE_TOUT 5000 70 # define CONFIG_FLASH_SHOW_PROGRESS 10 71 # define CONFIG_SYS_FLASH_CFI 72 # undef CONFIG_SYS_FLASH_EMPTY_INFO 73 # define CONFIG_FLASH_CFI_DRIVER 74 # undef CONFIG_SYS_FLASH_PROTECTION 75 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 76 #endif 77 78 #ifdef CONFIG_NAND_ZYNQ 79 #define CONFIG_CMD_NAND_LOCK_UNLOCK 80 #define CONFIG_SYS_MAX_NAND_DEVICE 1 81 #define CONFIG_SYS_NAND_ONFI_DETECTION 82 #define CONFIG_MTD_DEVICE 83 #endif 84 85 /* MMC */ 86 #if defined(CONFIG_MMC_SDHCI_ZYNQ) 87 # define CONFIG_ZYNQ_SDHCI_MAX_FREQ 52000000 88 #endif 89 90 #ifdef CONFIG_USB_EHCI_ZYNQ 91 # define CONFIG_EHCI_IS_TDI 92 93 # define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000 94 # define DFU_DEFAULT_POLL_TIMEOUT 300 95 # define CONFIG_USB_CABLE_CHECK 96 # define CONFIG_CMD_THOR_DOWNLOAD 97 # define CONFIG_THOR_RESET_OFF 98 # define CONFIG_USB_FUNCTION_THOR 99 # define DFU_ALT_INFO_RAM \ 100 "dfu_ram_info=" \ 101 "set dfu_alt_info " \ 102 "${kernel_image} ram 0x3000000 0x500000\\\\;" \ 103 "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \ 104 "${ramdisk_image} ram 0x2000000 0x600000\0" \ 105 "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \ 106 "thor_ram=run dfu_ram_info && thordown 0 ram 0\0" 107 108 # if defined(CONFIG_MMC_SDHCI_ZYNQ) 109 # define DFU_ALT_INFO_MMC \ 110 "dfu_mmc_info=" \ 111 "set dfu_alt_info " \ 112 "${kernel_image} fat 0 1\\\\;" \ 113 "${devicetree_image} fat 0 1\\\\;" \ 114 "${ramdisk_image} fat 0 1\0" \ 115 "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \ 116 "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0" 117 118 # define DFU_ALT_INFO \ 119 DFU_ALT_INFO_RAM \ 120 DFU_ALT_INFO_MMC 121 # else 122 # define DFU_ALT_INFO \ 123 DFU_ALT_INFO_RAM 124 # endif 125 #endif 126 127 #if !defined(DFU_ALT_INFO) 128 # define DFU_ALT_INFO 129 #endif 130 131 #if defined(CONFIG_MMC_SDHCI_ZYNQ) || defined(CONFIG_ZYNQ_USB) 132 # define CONFIG_SUPPORT_VFAT 133 # define CONFIG_FAT_WRITE 134 #endif 135 136 #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1) 137 #define CONFIG_SYS_I2C_ZYNQ 138 #endif 139 140 /* I2C */ 141 #if defined(CONFIG_SYS_I2C_ZYNQ) 142 # define CONFIG_SYS_I2C 143 # define CONFIG_SYS_I2C_ZYNQ_SPEED 100000 144 # define CONFIG_SYS_I2C_ZYNQ_SLAVE 0 145 #endif 146 147 /* EEPROM */ 148 #ifdef CONFIG_ZYNQ_EEPROM 149 # define CONFIG_CMD_EEPROM 150 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 151 # define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 152 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 153 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 154 # define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */ 155 #endif 156 157 /* Total Size of Environment Sector */ 158 #define CONFIG_ENV_SIZE (128 << 10) 159 160 /* Allow to overwrite serial and ethaddr */ 161 #define CONFIG_ENV_OVERWRITE 162 163 /* Environment */ 164 #ifndef CONFIG_ENV_IS_NOWHERE 165 # ifndef CONFIG_SYS_NO_FLASH 166 /* Environment in NOR flash */ 167 # define CONFIG_ENV_IS_IN_FLASH 168 # elif defined(CONFIG_ZYNQ_QSPI) 169 /* Environment in Serial Flash */ 170 # define CONFIG_ENV_IS_IN_SPI_FLASH 171 # elif defined(CONFIG_SYS_NO_FLASH) 172 # define CONFIG_ENV_IS_NOWHERE 173 # endif 174 175 # define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE 176 # define CONFIG_ENV_OFFSET 0xE0000 177 #endif 178 179 /* enable preboot to be loaded before CONFIG_BOOTDELAY */ 180 #define CONFIG_PREBOOT 181 182 /* Default environment */ 183 #ifndef CONFIG_EXTRA_ENV_SETTINGS 184 #define CONFIG_EXTRA_ENV_SETTINGS \ 185 "fit_image=fit.itb\0" \ 186 "load_addr=0x2000000\0" \ 187 "fit_size=0x800000\0" \ 188 "flash_off=0x100000\0" \ 189 "nor_flash_off=0xE2100000\0" \ 190 "fdt_high=0x20000000\0" \ 191 "initrd_high=0x20000000\0" \ 192 "loadbootenv_addr=0x2000000\0" \ 193 "bootenv=uEnv.txt\0" \ 194 "bootenv_dev=mmc\0" \ 195 "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \ 196 "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \ 197 "env import -t ${loadbootenv_addr} $filesize\0" \ 198 "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \ 199 "setbootenv=if env run bootenv_existence_test; then " \ 200 "if env run loadbootenv; then " \ 201 "env run importbootenv; " \ 202 "fi; " \ 203 "fi; \0" \ 204 "sd_loadbootenv=set bootenv_dev mmc && " \ 205 "run setbootenv \0" \ 206 "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \ 207 "preboot=if test $modeboot = sdboot; then " \ 208 "run sd_loadbootenv; " \ 209 "echo Checking if uenvcmd is set ...; " \ 210 "if test -n $uenvcmd; then " \ 211 "echo Running uenvcmd ...; " \ 212 "run uenvcmd; " \ 213 "fi; " \ 214 "fi; \0" \ 215 "norboot=echo Copying FIT from NOR flash to RAM... && " \ 216 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \ 217 "bootm ${load_addr}\0" \ 218 "sdboot=echo Copying FIT from SD to RAM... && " \ 219 "load mmc 0 ${load_addr} ${fit_image} && " \ 220 "bootm ${load_addr}\0" \ 221 "jtagboot=echo TFTPing FIT to RAM... && " \ 222 "tftpboot ${load_addr} ${fit_image} && " \ 223 "bootm ${load_addr}\0" \ 224 "usbboot=if usb start; then " \ 225 "echo Copying FIT from USB to RAM... && " \ 226 "load usb 0 ${load_addr} ${fit_image} && " \ 227 "bootm ${load_addr}; fi\0" \ 228 DFU_ALT_INFO 229 #endif 230 231 #define CONFIG_BOOTCOMMAND "run $modeboot" 232 #define CONFIG_SYS_LOAD_ADDR 0 /* default? */ 233 234 /* Miscellaneous configurable options */ 235 236 #define CONFIG_CMDLINE_EDITING 237 #define CONFIG_AUTO_COMPLETE 238 #define CONFIG_SYS_LONGHELP 239 #define CONFIG_CLOCKS 240 #define CONFIG_CMD_CLK 241 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 242 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 243 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 244 sizeof(CONFIG_SYS_PROMPT) + 16) 245 246 #ifndef CONFIG_NR_DRAM_BANKS 247 # define CONFIG_NR_DRAM_BANKS 1 248 #endif 249 250 #define CONFIG_SYS_MEMTEST_START 0 251 #define CONFIG_SYS_MEMTEST_END 0x1000 252 253 #define CONFIG_SYS_MALLOC_LEN 0x1400000 254 255 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 256 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 257 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 258 CONFIG_SYS_INIT_RAM_SIZE - \ 259 GENERATED_GBL_DATA_SIZE) 260 261 /* Enable the PL to be downloaded */ 262 #define CONFIG_FPGA 263 #define CONFIG_FPGA_XILINX 264 #define CONFIG_FPGA_ZYNQPL 265 #define CONFIG_CMD_FPGA_LOADMK 266 #define CONFIG_CMD_FPGA_LOADP 267 #define CONFIG_CMD_FPGA_LOADBP 268 #define CONFIG_CMD_FPGA_LOADFS 269 270 /* FIT support */ 271 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */ 272 273 /* FDT support */ 274 #define CONFIG_DISPLAY_BOARDINFO_LATE 275 276 /* Extend size of kernel image for uncompression */ 277 #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024) 278 279 /* Boot FreeBSD/vxWorks from an ELF image */ 280 #define CONFIG_SYS_MMC_MAX_DEVICE 1 281 282 #define CONFIG_SYS_LDSCRIPT "arch/arm/mach-zynq/u-boot.lds" 283 284 /* Commands */ 285 286 /* SPL part */ 287 #define CONFIG_CMD_SPL 288 #define CONFIG_SPL_FRAMEWORK 289 #define CONFIG_SPL_BOARD_INIT 290 291 #define CONFIG_SPL_LDSCRIPT "arch/arm/mach-zynq/u-boot-spl.lds" 292 293 /* MMC support */ 294 #ifdef CONFIG_MMC_SDHCI_ZYNQ 295 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 296 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 297 #endif 298 299 /* Disable dcache for SPL just for sure */ 300 #ifdef CONFIG_SPL_BUILD 301 #define CONFIG_SYS_DCACHE_OFF 302 #undef CONFIG_FPGA 303 #endif 304 305 /* Address in RAM where the parameters must be copied by SPL. */ 306 #define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000 307 308 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb" 309 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 310 311 /* Not using MMC raw mode - just for compilation purpose */ 312 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 313 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 314 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 315 316 /* qspi mode is working fine */ 317 #ifdef CONFIG_ZYNQ_QSPI 318 #define CONFIG_SPL_SPI_LOAD 319 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000 320 #define CONFIG_SYS_SPI_ARGS_OFFS 0x200000 321 #define CONFIG_SYS_SPI_ARGS_SIZE 0x80000 322 #define CONFIG_SYS_SPI_KERNEL_OFFS (CONFIG_SYS_SPI_ARGS_OFFS + \ 323 CONFIG_SYS_SPI_ARGS_SIZE) 324 #endif 325 326 /* for booting directly linux */ 327 328 /* SP location before relocation, must use scratch RAM */ 329 #define CONFIG_SPL_TEXT_BASE 0x0 330 331 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */ 332 #define CONFIG_SPL_MAX_SIZE 0x30000 333 334 /* The highest 64k OCM address */ 335 #define OCM_HIGH_ADDR 0xffff0000 336 337 /* On the top of OCM space */ 338 #define CONFIG_SYS_SPL_MALLOC_START OCM_HIGH_ADDR 339 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000 340 341 /* 342 * SPL stack position - and stack goes down 343 * 0xfffffe00 is used for putting wfi loop. 344 * Set it up as limit for now. 345 */ 346 #define CONFIG_SPL_STACK 0xfffffe00 347 348 /* BSS setup */ 349 #define CONFIG_SPL_BSS_START_ADDR 0x100000 350 #define CONFIG_SPL_BSS_MAX_SIZE 0x100000 351 352 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 353 354 #endif /* __CONFIG_ZYNQ_COMMON_H */ 355