1 /*
2  * (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
3  * (C) Copyright 2013 Xilinx, Inc.
4  *
5  * Common configuration options for all Zynq boards.
6  *
7  * SPDX-License-Identifier:	GPL-2.0+
8  */
9 
10 #ifndef __CONFIG_ZYNQ_COMMON_H
11 #define __CONFIG_ZYNQ_COMMON_H
12 
13 /* CPU clock */
14 #ifndef CONFIG_CPU_FREQ_HZ
15 # define CONFIG_CPU_FREQ_HZ	800000000
16 #endif
17 
18 /* Cache options */
19 #define CONFIG_CMD_CACHE
20 #define CONFIG_SYS_CACHELINE_SIZE	32
21 
22 #define CONFIG_SYS_L2CACHE_OFF
23 #ifndef CONFIG_SYS_L2CACHE_OFF
24 # define CONFIG_SYS_L2_PL310
25 # define CONFIG_SYS_PL310_BASE		0xf8f02000
26 #endif
27 
28 #define ZYNQ_SCUTIMER_BASEADDR		0xF8F00600
29 #define CONFIG_SYS_TIMERBASE		ZYNQ_SCUTIMER_BASEADDR
30 #define CONFIG_SYS_TIMER_COUNTS_DOWN
31 #define CONFIG_SYS_TIMER_COUNTER	(CONFIG_SYS_TIMERBASE + 0x4)
32 
33 /* Serial drivers */
34 #define CONFIG_BAUDRATE		115200
35 /* The following table includes the supported baudrates */
36 #define CONFIG_SYS_BAUDRATE_TABLE  \
37 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
38 
39 /* DCC driver */
40 #if defined(CONFIG_ZYNQ_DCC)
41 # define CONFIG_ARM_DCC
42 #else
43 # define CONFIG_ZYNQ_SERIAL
44 #endif
45 
46 #define CONFIG_ZYNQ_GPIO
47 
48 /* Ethernet driver */
49 #if defined(CONFIG_ZYNQ_GEM)
50 # define CONFIG_MII
51 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
52 # define CONFIG_PHY_MARVELL
53 # define CONFIG_BOOTP_SERVERIP
54 # define CONFIG_BOOTP_BOOTPATH
55 # define CONFIG_BOOTP_GATEWAY
56 # define CONFIG_BOOTP_HOSTNAME
57 # define CONFIG_BOOTP_MAY_FAIL
58 #endif
59 
60 /* SPI */
61 #ifdef CONFIG_ZYNQ_SPI
62 # define CONFIG_CMD_SF
63 #endif
64 
65 /* QSPI */
66 #ifdef CONFIG_ZYNQ_QSPI
67 # define CONFIG_SF_DEFAULT_SPEED	30000000
68 # define CONFIG_SPI_FLASH_ISSI
69 # define CONFIG_SPI_FLASH_BAR
70 # define CONFIG_CMD_SF
71 #endif
72 
73 /* NOR */
74 #ifndef CONFIG_SYS_NO_FLASH
75 # define CONFIG_SYS_FLASH_BASE		0xE2000000
76 # define CONFIG_SYS_FLASH_SIZE		(16 * 1024 * 1024)
77 # define CONFIG_SYS_MAX_FLASH_BANKS	1
78 # define CONFIG_SYS_MAX_FLASH_SECT	512
79 # define CONFIG_SYS_FLASH_ERASE_TOUT	1000
80 # define CONFIG_SYS_FLASH_WRITE_TOUT	5000
81 # define CONFIG_FLASH_SHOW_PROGRESS	10
82 # define CONFIG_SYS_FLASH_CFI
83 # undef CONFIG_SYS_FLASH_EMPTY_INFO
84 # define CONFIG_FLASH_CFI_DRIVER
85 # undef CONFIG_SYS_FLASH_PROTECTION
86 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
87 #endif
88 
89 /* MMC */
90 #if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
91 # define CONFIG_MMC
92 # define CONFIG_GENERIC_MMC
93 # define CONFIG_SDHCI
94 # define CONFIG_ZYNQ_SDHCI
95 # define CONFIG_CMD_MMC
96 # define CONFIG_ZYNQ_SDHCI_MAX_FREQ	52000000
97 #endif
98 
99 #ifdef CONFIG_ZYNQ_USB
100 # define CONFIG_USB_EHCI
101 # define CONFIG_CMD_USB
102 # define CONFIG_USB_STORAGE
103 # define CONFIG_USB_EHCI_ZYNQ
104 # define CONFIG_USB_ULPI_VIEWPORT
105 # define CONFIG_USB_ULPI
106 # define CONFIG_EHCI_IS_TDI
107 # define CONFIG_USB_MAX_CONTROLLER_COUNT	2
108 
109 # define CONFIG_CI_UDC           /* ChipIdea CI13xxx UDC */
110 # define CONFIG_USB_GADGET
111 # define CONFIG_USB_GADGET_DUALSPEED
112 # define CONFIG_USB_GADGET_DOWNLOAD
113 # define CONFIG_SYS_DFU_DATA_BUF_SIZE	0x600000
114 # define DFU_DEFAULT_POLL_TIMEOUT	300
115 # define CONFIG_USB_FUNCTION_DFU
116 # define CONFIG_DFU_RAM
117 # define CONFIG_USB_GADGET_VBUS_DRAW	2
118 # define CONFIG_G_DNL_VENDOR_NUM	0x03FD
119 # define CONFIG_G_DNL_PRODUCT_NUM	0x0300
120 # define CONFIG_G_DNL_MANUFACTURER	"Xilinx"
121 # define CONFIG_USB_GADGET
122 # define CONFIG_USB_CABLE_CHECK
123 # define CONFIG_CMD_DFU
124 # define CONFIG_CMD_THOR_DOWNLOAD
125 # define CONFIG_USB_FUNCTION_THOR
126 # define DFU_ALT_INFO_RAM \
127 	"dfu_ram_info=" \
128 	"set dfu_alt_info " \
129 	"${kernel_image} ram 0x3000000 0x500000\\\\;" \
130 	"${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
131 	"${ramdisk_image} ram 0x2000000 0x600000\0" \
132 	"dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
133 	"thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
134 
135 # if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
136 #  define CONFIG_DFU_MMC
137 #  define DFU_ALT_INFO_MMC \
138 	"dfu_mmc_info=" \
139 	"set dfu_alt_info " \
140 	"${kernel_image} fat 0 1\\\\;" \
141 	"${devicetree_image} fat 0 1\\\\;" \
142 	"${ramdisk_image} fat 0 1\0" \
143 	"dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
144 	"thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"
145 
146 #  define DFU_ALT_INFO	\
147 	DFU_ALT_INFO_RAM \
148 	DFU_ALT_INFO_MMC
149 # else
150 #  define DFU_ALT_INFO	\
151 	DFU_ALT_INFO_RAM
152 # endif
153 #endif
154 
155 #if !defined(DFU_ALT_INFO)
156 # define DFU_ALT_INFO
157 #endif
158 
159 #if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB)
160 # define CONFIG_SUPPORT_VFAT
161 # define CONFIG_CMD_FAT
162 # define CONFIG_CMD_EXT2
163 # define CONFIG_FAT_WRITE
164 # define CONFIG_DOS_PARTITION
165 # define CONFIG_CMD_EXT4
166 # define CONFIG_CMD_EXT4_WRITE
167 # define CONFIG_CMD_FS_GENERIC
168 #endif
169 
170 #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1)
171 #define CONFIG_SYS_I2C_ZYNQ
172 #endif
173 
174 /* I2C */
175 #if defined(CONFIG_SYS_I2C_ZYNQ)
176 # define CONFIG_CMD_I2C
177 # define CONFIG_SYS_I2C
178 # define CONFIG_SYS_I2C_ZYNQ_SPEED		100000
179 # define CONFIG_SYS_I2C_ZYNQ_SLAVE		0
180 #endif
181 
182 /* EEPROM */
183 #ifdef CONFIG_ZYNQ_EEPROM
184 # define CONFIG_CMD_EEPROM
185 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
186 # define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
187 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
188 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
189 # define CONFIG_SYS_EEPROM_SIZE			1024 /* Bytes */
190 #endif
191 
192 /* Total Size of Environment Sector */
193 #define CONFIG_ENV_SIZE			(128 << 10)
194 
195 /* Allow to overwrite serial and ethaddr */
196 #define CONFIG_ENV_OVERWRITE
197 
198 /* Environment */
199 #ifndef CONFIG_ENV_IS_NOWHERE
200 # ifndef CONFIG_SYS_NO_FLASH
201 #  define CONFIG_ENV_IS_IN_FLASH
202 # elif defined(CONFIG_SYS_NO_FLASH)
203 #  define CONFIG_ENV_IS_NOWHERE
204 # endif
205 
206 # define CONFIG_ENV_SECT_SIZE		CONFIG_ENV_SIZE
207 # define CONFIG_ENV_OFFSET		0xE0000
208 #endif
209 
210 /* Default environment */
211 #define CONFIG_EXTRA_ENV_SETTINGS	\
212 	"fit_image=fit.itb\0"		\
213 	"load_addr=0x2000000\0"		\
214 	"fit_size=0x800000\0"		\
215 	"flash_off=0x100000\0"		\
216 	"nor_flash_off=0xE2100000\0"	\
217 	"fdt_high=0x20000000\0"		\
218 	"initrd_high=0x20000000\0"	\
219 	"norboot=echo Copying FIT from NOR flash to RAM... && " \
220 		"cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
221 		"bootm ${load_addr}\0" \
222 	"sdboot=echo Copying FIT from SD to RAM... && " \
223 		"load mmc 0 ${load_addr} ${fit_image} && " \
224 		"bootm ${load_addr}\0" \
225 	"jtagboot=echo TFTPing FIT to RAM... && " \
226 		"tftpboot ${load_addr} ${fit_image} && " \
227 		"bootm ${load_addr}\0" \
228 	"usbboot=if usb start; then " \
229 			"echo Copying FIT from USB to RAM... && " \
230 			"load usb 0 ${load_addr} ${fit_image} && " \
231 			"bootm ${load_addr}\0" \
232 		"fi\0" \
233 		DFU_ALT_INFO
234 
235 #define CONFIG_BOOTCOMMAND		"run $modeboot"
236 #define CONFIG_BOOTDELAY		3 /* -1 to Disable autoboot */
237 #define CONFIG_SYS_LOAD_ADDR		0 /* default? */
238 
239 /* Miscellaneous configurable options */
240 #define CONFIG_SYS_HUSH_PARSER
241 
242 #define CONFIG_CMDLINE_EDITING
243 #define CONFIG_AUTO_COMPLETE
244 #define CONFIG_BOARD_LATE_INIT
245 #define CONFIG_DISPLAY_BOARDINFO
246 #define CONFIG_SYS_LONGHELP
247 #define CONFIG_CLOCKS
248 #define CONFIG_CMD_CLK
249 #define CONFIG_SYS_MAXARGS		32 /* max number of command args */
250 #define CONFIG_SYS_CBSIZE		256 /* Console I/O Buffer Size */
251 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
252 					sizeof(CONFIG_SYS_PROMPT) + 16)
253 
254 /* Physical Memory map */
255 #define CONFIG_SYS_TEXT_BASE		0x4000000
256 
257 #define CONFIG_NR_DRAM_BANKS		1
258 #define CONFIG_SYS_SDRAM_BASE		0
259 
260 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
261 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x1000)
262 
263 #define CONFIG_SYS_MALLOC_LEN		0x1400000
264 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_SDRAM_BASE
265 #define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_MALLOC_LEN
266 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
267 					CONFIG_SYS_INIT_RAM_SIZE - \
268 					GENERATED_GBL_DATA_SIZE)
269 
270 /* Enable the PL to be downloaded */
271 #define CONFIG_FPGA
272 #define CONFIG_FPGA_XILINX
273 #define CONFIG_FPGA_ZYNQPL
274 #define CONFIG_CMD_FPGA_LOADMK
275 #define CONFIG_CMD_FPGA_LOADP
276 #define CONFIG_CMD_FPGA_LOADBP
277 #define CONFIG_CMD_FPGA_LOADFS
278 
279 /* Open Firmware flat tree */
280 #define CONFIG_OF_LIBFDT
281 
282 /* FIT support */
283 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
284 
285 /* FDT support */
286 #define CONFIG_DISPLAY_BOARDINFO_LATE
287 
288 /* Extend size of kernel image for uncompression */
289 #define CONFIG_SYS_BOOTM_LEN	(60 * 1024 * 1024)
290 
291 /* Boot FreeBSD/vxWorks from an ELF image */
292 #if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
293 # define CONFIG_SYS_MMC_MAX_DEVICE	1
294 #endif
295 
296 #define CONFIG_SYS_LDSCRIPT  "arch/arm/mach-zynq/u-boot.lds"
297 
298 /* Commands */
299 #define CONFIG_CMD_PING
300 #define CONFIG_CMD_DHCP
301 #define CONFIG_CMD_MII
302 #define CONFIG_CMD_TFTPPUT
303 
304 /* SPL part */
305 #define CONFIG_CMD_SPL
306 #define CONFIG_SPL_FRAMEWORK
307 #define CONFIG_SPL_LIBCOMMON_SUPPORT
308 #define CONFIG_SPL_LIBGENERIC_SUPPORT
309 #define CONFIG_SPL_SERIAL_SUPPORT
310 #define CONFIG_SPL_BOARD_INIT
311 
312 #define CONFIG_SPL_LDSCRIPT	"arch/arm/mach-zynq/u-boot-spl.lds"
313 
314 /* MMC support */
315 #ifdef CONFIG_ZYNQ_SDHCI0
316 #define CONFIG_SPL_MMC_SUPPORT
317 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
318 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
319 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
320 #define CONFIG_SPL_LIBDISK_SUPPORT
321 #define CONFIG_SPL_FAT_SUPPORT
322 #ifdef CONFIG_OF_SEPARATE
323 # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
324 #else
325 # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"
326 #endif
327 #endif
328 
329 /* Disable dcache for SPL just for sure */
330 #ifdef CONFIG_SPL_BUILD
331 #define CONFIG_SYS_DCACHE_OFF
332 #undef CONFIG_FPGA
333 #endif
334 
335 /* Address in RAM where the parameters must be copied by SPL. */
336 #define CONFIG_SYS_SPL_ARGS_ADDR	0x10000000
337 
338 #define CONFIG_SPL_FS_LOAD_ARGS_NAME		"system.dtb"
339 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME		"uImage"
340 
341 /* Not using MMC raw mode - just for compilation purpose */
342 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0
343 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	0
344 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR	0
345 
346 /* qspi mode is working fine */
347 #ifdef CONFIG_ZYNQ_QSPI
348 #define CONFIG_SPL_SPI_SUPPORT
349 #define CONFIG_SPL_SPI_LOAD
350 #define CONFIG_SPL_SPI_FLASH_SUPPORT
351 #define CONFIG_SYS_SPI_U_BOOT_OFFS	0x100000
352 #define CONFIG_SYS_SPI_ARGS_OFFS	0x200000
353 #define CONFIG_SYS_SPI_ARGS_SIZE	0x80000
354 #define CONFIG_SYS_SPI_KERNEL_OFFS	(CONFIG_SYS_SPI_ARGS_OFFS + \
355 					CONFIG_SYS_SPI_ARGS_SIZE)
356 #endif
357 
358 /* for booting directly linux */
359 #define CONFIG_SPL_OS_BOOT
360 
361 /* SP location before relocation, must use scratch RAM */
362 #define CONFIG_SPL_TEXT_BASE	0x0
363 
364 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
365 #define CONFIG_SPL_MAX_SIZE	0x30000
366 
367 /* The highest 64k OCM address */
368 #define OCM_HIGH_ADDR	0xffff0000
369 
370 /* On the top of OCM space */
371 #define CONFIG_SYS_SPL_MALLOC_START	OCM_HIGH_ADDR
372 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x2000
373 
374 /*
375  * SPL stack position - and stack goes down
376  * 0xfffffe00 is used for putting wfi loop.
377  * Set it up as limit for now.
378  */
379 #define CONFIG_SPL_STACK	0xfffffe00
380 
381 /* BSS setup */
382 #define CONFIG_SPL_BSS_START_ADDR	0x100000
383 #define CONFIG_SPL_BSS_MAX_SIZE		0x100000
384 
385 #define CONFIG_SYS_UBOOT_START	CONFIG_SYS_TEXT_BASE
386 
387 
388 #endif /* __CONFIG_ZYNQ_COMMON_H */
389