1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2012 Michal Simek <monstr@monstr.eu> 4 * (C) Copyright 2013 - 2018 Xilinx, Inc. 5 * 6 * Common configuration options for all Zynq boards. 7 */ 8 9 #ifndef __CONFIG_ZYNQ_COMMON_H 10 #define __CONFIG_ZYNQ_COMMON_H 11 12 /* CPU clock */ 13 #ifndef CONFIG_CPU_FREQ_HZ 14 # define CONFIG_CPU_FREQ_HZ 800000000 15 #endif 16 17 /* Cache options */ 18 #define CONFIG_SYS_L2CACHE_OFF 19 #ifndef CONFIG_SYS_L2CACHE_OFF 20 # define CONFIG_SYS_L2_PL310 21 # define CONFIG_SYS_PL310_BASE 0xf8f02000 22 #endif 23 24 #define ZYNQ_SCUTIMER_BASEADDR 0xF8F00600 25 #define CONFIG_SYS_TIMERBASE ZYNQ_SCUTIMER_BASEADDR 26 #define CONFIG_SYS_TIMER_COUNTS_DOWN 27 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) 28 29 /* Serial drivers */ 30 /* The following table includes the supported baudrates */ 31 #define CONFIG_SYS_BAUDRATE_TABLE \ 32 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} 33 34 #define CONFIG_ARM_DCC 35 36 /* Ethernet driver */ 37 #if defined(CONFIG_ZYNQ_GEM) 38 # define CONFIG_MII 39 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 40 # define CONFIG_BOOTP_MAY_FAIL 41 #endif 42 43 /* QSPI */ 44 #ifdef CONFIG_ZYNQ_QSPI 45 # define CONFIG_SF_DEFAULT_SPEED 30000000 46 # define CONFIG_SPI_FLASH_ISSI 47 #endif 48 49 /* NOR */ 50 #ifdef CONFIG_MTD_NOR_FLASH 51 # define CONFIG_SYS_FLASH_BASE 0xE2000000 52 # define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024) 53 # define CONFIG_SYS_MAX_FLASH_BANKS 1 54 # define CONFIG_SYS_MAX_FLASH_SECT 512 55 # define CONFIG_SYS_FLASH_ERASE_TOUT 1000 56 # define CONFIG_SYS_FLASH_WRITE_TOUT 5000 57 # define CONFIG_FLASH_SHOW_PROGRESS 10 58 # define CONFIG_SYS_FLASH_CFI 59 # undef CONFIG_SYS_FLASH_EMPTY_INFO 60 # define CONFIG_FLASH_CFI_DRIVER 61 # undef CONFIG_SYS_FLASH_PROTECTION 62 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 63 #endif 64 65 #ifdef CONFIG_NAND_ZYNQ 66 #define CONFIG_SYS_MAX_NAND_DEVICE 1 67 #define CONFIG_SYS_NAND_ONFI_DETECTION 68 #endif 69 70 #ifdef CONFIG_USB_EHCI_ZYNQ 71 # define CONFIG_EHCI_IS_TDI 72 73 # define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000 74 # define DFU_DEFAULT_POLL_TIMEOUT 300 75 # define CONFIG_USB_CABLE_CHECK 76 # define CONFIG_THOR_RESET_OFF 77 # define DFU_ALT_INFO_RAM \ 78 "dfu_ram_info=" \ 79 "set dfu_alt_info " \ 80 "${kernel_image} ram 0x3000000 0x500000\\\\;" \ 81 "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \ 82 "${ramdisk_image} ram 0x2000000 0x600000\0" \ 83 "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \ 84 "thor_ram=run dfu_ram_info && thordown 0 ram 0\0" 85 86 # if defined(CONFIG_MMC_SDHCI_ZYNQ) 87 # define DFU_ALT_INFO_MMC \ 88 "dfu_mmc_info=" \ 89 "set dfu_alt_info " \ 90 "${kernel_image} fat 0 1\\\\;" \ 91 "${devicetree_image} fat 0 1\\\\;" \ 92 "${ramdisk_image} fat 0 1\0" \ 93 "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \ 94 "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0" 95 96 # define DFU_ALT_INFO \ 97 DFU_ALT_INFO_RAM \ 98 DFU_ALT_INFO_MMC 99 # else 100 # define DFU_ALT_INFO \ 101 DFU_ALT_INFO_RAM 102 # endif 103 #endif 104 105 #if !defined(DFU_ALT_INFO) 106 # define DFU_ALT_INFO 107 #endif 108 109 /* I2C */ 110 #if defined(CONFIG_SYS_I2C_ZYNQ) 111 # define CONFIG_SYS_I2C 112 #endif 113 114 /* EEPROM */ 115 #ifdef CONFIG_ZYNQ_EEPROM 116 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 117 # define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 118 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 119 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 120 # define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */ 121 #endif 122 123 /* Allow to overwrite serial and ethaddr */ 124 #define CONFIG_ENV_OVERWRITE 125 126 /* enable preboot to be loaded before CONFIG_BOOTDELAY */ 127 #define CONFIG_PREBOOT 128 129 /* Boot configuration */ 130 #define CONFIG_SYS_LOAD_ADDR 0 /* default? */ 131 132 /* Distro boot enablement */ 133 134 #ifdef CONFIG_SPL_BUILD 135 #define BOOTENV 136 #else 137 138 #ifdef CONFIG_CMD_MMC 139 #define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) 140 #else 141 #define BOOT_TARGET_DEVICES_MMC(func) 142 #endif 143 144 #ifdef CONFIG_CMD_USB 145 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) 146 #else 147 #define BOOT_TARGET_DEVICES_USB(func) 148 #endif 149 150 #if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP) 151 #define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na) 152 #else 153 #define BOOT_TARGET_DEVICES_PXE(func) 154 #endif 155 156 #if defined(CONFIG_CMD_DHCP) 157 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na) 158 #else 159 #define BOOT_TARGET_DEVICES_DHCP(func) 160 #endif 161 162 #define BOOT_TARGET_DEVICES(func) \ 163 BOOT_TARGET_DEVICES_MMC(func) \ 164 BOOT_TARGET_DEVICES_USB(func) \ 165 BOOT_TARGET_DEVICES_PXE(func) \ 166 BOOT_TARGET_DEVICES_DHCP(func) 167 168 #include <config_distro_bootcmd.h> 169 #endif /* CONFIG_SPL_BUILD */ 170 171 /* Default environment */ 172 #ifndef CONFIG_EXTRA_ENV_SETTINGS 173 #define CONFIG_EXTRA_ENV_SETTINGS \ 174 "fit_image=fit.itb\0" \ 175 "load_addr=0x2000000\0" \ 176 "fit_size=0x800000\0" \ 177 "flash_off=0x100000\0" \ 178 "nor_flash_off=0xE2100000\0" \ 179 "fdt_high=0x20000000\0" \ 180 "initrd_high=0x20000000\0" \ 181 "loadbootenv_addr=0x2000000\0" \ 182 "fdt_addr_r=0x1f00000\0" \ 183 "pxefile_addr_r=0x2000000\0" \ 184 "kernel_addr_r=0x2000000\0" \ 185 "scriptaddr=0x3000000\0" \ 186 "ramdisk_addr_r=0x3100000\0" \ 187 "bootenv=uEnv.txt\0" \ 188 "bootenv_dev=mmc\0" \ 189 "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \ 190 "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \ 191 "env import -t ${loadbootenv_addr} $filesize\0" \ 192 "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \ 193 "setbootenv=if env run bootenv_existence_test; then " \ 194 "if env run loadbootenv; then " \ 195 "env run importbootenv; " \ 196 "fi; " \ 197 "fi; \0" \ 198 "sd_loadbootenv=set bootenv_dev mmc && " \ 199 "run setbootenv \0" \ 200 "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \ 201 "preboot=if test $modeboot = sdboot; then " \ 202 "run sd_loadbootenv; " \ 203 "echo Checking if uenvcmd is set ...; " \ 204 "if test -n $uenvcmd; then " \ 205 "echo Running uenvcmd ...; " \ 206 "run uenvcmd; " \ 207 "fi; " \ 208 "fi; \0" \ 209 "norboot=echo Copying FIT from NOR flash to RAM... && " \ 210 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \ 211 "bootm ${load_addr}\0" \ 212 "sdboot=echo Copying FIT from SD to RAM... && " \ 213 "load mmc 0 ${load_addr} ${fit_image} && " \ 214 "bootm ${load_addr}\0" \ 215 "jtagboot=echo TFTPing FIT to RAM... && " \ 216 "tftpboot ${load_addr} ${fit_image} && " \ 217 "bootm ${load_addr}\0" \ 218 "usbboot=if usb start; then " \ 219 "echo Copying FIT from USB to RAM... && " \ 220 "load usb 0 ${load_addr} ${fit_image} && " \ 221 "bootm ${load_addr}; fi\0" \ 222 DFU_ALT_INFO \ 223 BOOTENV 224 #endif 225 226 /* Miscellaneous configurable options */ 227 228 #define CONFIG_CLOCKS 229 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 230 231 #ifndef CONFIG_NR_DRAM_BANKS 232 # define CONFIG_NR_DRAM_BANKS 1 233 #endif 234 235 #define CONFIG_SYS_MEMTEST_START 0 236 #define CONFIG_SYS_MEMTEST_END 0x1000 237 238 #define CONFIG_SYS_MALLOC_LEN 0x1400000 239 240 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 241 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 242 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 243 CONFIG_SYS_INIT_RAM_SIZE - \ 244 GENERATED_GBL_DATA_SIZE) 245 246 247 /* Extend size of kernel image for uncompression */ 248 #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024) 249 250 /* Boot FreeBSD/vxWorks from an ELF image */ 251 #define CONFIG_SYS_MMC_MAX_DEVICE 1 252 253 #define CONFIG_SYS_LDSCRIPT "arch/arm/mach-zynq/u-boot.lds" 254 255 /* Commands */ 256 257 /* SPL part */ 258 259 /* MMC support */ 260 #ifdef CONFIG_MMC_SDHCI_ZYNQ 261 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 262 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 263 #endif 264 265 /* Disable dcache for SPL just for sure */ 266 #ifdef CONFIG_SPL_BUILD 267 #define CONFIG_SYS_DCACHE_OFF 268 #endif 269 270 /* Address in RAM where the parameters must be copied by SPL. */ 271 #define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000 272 273 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb" 274 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 275 276 /* Not using MMC raw mode - just for compilation purpose */ 277 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 278 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 279 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 280 281 /* qspi mode is working fine */ 282 #ifdef CONFIG_ZYNQ_QSPI 283 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000 284 #define CONFIG_SYS_SPI_ARGS_OFFS 0x200000 285 #define CONFIG_SYS_SPI_ARGS_SIZE 0x80000 286 #define CONFIG_SYS_SPI_KERNEL_OFFS (CONFIG_SYS_SPI_ARGS_OFFS + \ 287 CONFIG_SYS_SPI_ARGS_SIZE) 288 #endif 289 290 /* for booting directly linux */ 291 292 /* SP location before relocation, must use scratch RAM */ 293 #define CONFIG_SPL_TEXT_BASE 0x0 294 295 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */ 296 #define CONFIG_SPL_MAX_SIZE 0x30000 297 298 /* On the top of OCM space */ 299 #define CONFIG_SYS_SPL_MALLOC_START CONFIG_SPL_STACK_R_ADDR 300 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000000 301 302 /* 303 * SPL stack position - and stack goes down 304 * 0xfffffe00 is used for putting wfi loop. 305 * Set it up as limit for now. 306 */ 307 #define CONFIG_SPL_STACK 0xfffffe00 308 309 /* BSS setup */ 310 #define CONFIG_SPL_BSS_START_ADDR 0x100000 311 #define CONFIG_SPL_BSS_MAX_SIZE 0x100000 312 313 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 314 315 #endif /* __CONFIG_ZYNQ_COMMON_H */ 316