1 /* 2 * (C) Copyright 2012 Michal Simek <monstr@monstr.eu> 3 * (C) Copyright 2013 Xilinx, Inc. 4 * 5 * Common configuration options for all Zynq boards. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_ZYNQ_COMMON_H 11 #define __CONFIG_ZYNQ_COMMON_H 12 13 /* CPU clock */ 14 #ifndef CONFIG_CPU_FREQ_HZ 15 # define CONFIG_CPU_FREQ_HZ 800000000 16 #endif 17 18 /* Cache options */ 19 #define CONFIG_SYS_L2CACHE_OFF 20 #ifndef CONFIG_SYS_L2CACHE_OFF 21 # define CONFIG_SYS_L2_PL310 22 # define CONFIG_SYS_PL310_BASE 0xf8f02000 23 #endif 24 25 #define ZYNQ_SCUTIMER_BASEADDR 0xF8F00600 26 #define CONFIG_SYS_TIMERBASE ZYNQ_SCUTIMER_BASEADDR 27 #define CONFIG_SYS_TIMER_COUNTS_DOWN 28 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) 29 30 /* Serial drivers */ 31 /* The following table includes the supported baudrates */ 32 #define CONFIG_SYS_BAUDRATE_TABLE \ 33 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} 34 35 #define CONFIG_ARM_DCC 36 37 /* Ethernet driver */ 38 #if defined(CONFIG_ZYNQ_GEM) 39 # define CONFIG_MII 40 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 41 # define CONFIG_PHY_MARVELL 42 # define CONFIG_PHY_REALTEK 43 # define CONFIG_PHY_XILINX 44 # define CONFIG_BOOTP_BOOTPATH 45 # define CONFIG_BOOTP_GATEWAY 46 # define CONFIG_BOOTP_HOSTNAME 47 # define CONFIG_BOOTP_MAY_FAIL 48 #endif 49 50 /* SPI */ 51 #ifdef CONFIG_ZYNQ_SPI 52 #endif 53 54 /* QSPI */ 55 #ifdef CONFIG_ZYNQ_QSPI 56 # define CONFIG_SF_DEFAULT_SPEED 30000000 57 # define CONFIG_SPI_FLASH_ISSI 58 #endif 59 60 /* NOR */ 61 #ifdef CONFIG_MTD_NOR_FLASH 62 # define CONFIG_SYS_FLASH_BASE 0xE2000000 63 # define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024) 64 # define CONFIG_SYS_MAX_FLASH_BANKS 1 65 # define CONFIG_SYS_MAX_FLASH_SECT 512 66 # define CONFIG_SYS_FLASH_ERASE_TOUT 1000 67 # define CONFIG_SYS_FLASH_WRITE_TOUT 5000 68 # define CONFIG_FLASH_SHOW_PROGRESS 10 69 # define CONFIG_SYS_FLASH_CFI 70 # undef CONFIG_SYS_FLASH_EMPTY_INFO 71 # define CONFIG_FLASH_CFI_DRIVER 72 # undef CONFIG_SYS_FLASH_PROTECTION 73 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 74 #endif 75 76 #ifdef CONFIG_NAND_ZYNQ 77 #define CONFIG_SYS_MAX_NAND_DEVICE 1 78 #define CONFIG_SYS_NAND_ONFI_DETECTION 79 #define CONFIG_MTD_DEVICE 80 #endif 81 82 /* MMC */ 83 #if defined(CONFIG_MMC_SDHCI_ZYNQ) 84 # define CONFIG_ZYNQ_SDHCI_MAX_FREQ 52000000 85 #endif 86 87 #ifdef CONFIG_USB_EHCI_ZYNQ 88 # define CONFIG_EHCI_IS_TDI 89 90 # define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000 91 # define DFU_DEFAULT_POLL_TIMEOUT 300 92 # define CONFIG_USB_CABLE_CHECK 93 # define CONFIG_THOR_RESET_OFF 94 # define CONFIG_USB_FUNCTION_THOR 95 # define DFU_ALT_INFO_RAM \ 96 "dfu_ram_info=" \ 97 "set dfu_alt_info " \ 98 "${kernel_image} ram 0x3000000 0x500000\\\\;" \ 99 "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \ 100 "${ramdisk_image} ram 0x2000000 0x600000\0" \ 101 "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \ 102 "thor_ram=run dfu_ram_info && thordown 0 ram 0\0" 103 104 # if defined(CONFIG_MMC_SDHCI_ZYNQ) 105 # define DFU_ALT_INFO_MMC \ 106 "dfu_mmc_info=" \ 107 "set dfu_alt_info " \ 108 "${kernel_image} fat 0 1\\\\;" \ 109 "${devicetree_image} fat 0 1\\\\;" \ 110 "${ramdisk_image} fat 0 1\0" \ 111 "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \ 112 "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0" 113 114 # define DFU_ALT_INFO \ 115 DFU_ALT_INFO_RAM \ 116 DFU_ALT_INFO_MMC 117 # else 118 # define DFU_ALT_INFO \ 119 DFU_ALT_INFO_RAM 120 # endif 121 #endif 122 123 #if !defined(DFU_ALT_INFO) 124 # define DFU_ALT_INFO 125 #endif 126 127 #if defined(CONFIG_MMC_SDHCI_ZYNQ) || defined(CONFIG_ZYNQ_USB) 128 # define CONFIG_SUPPORT_VFAT 129 #endif 130 131 #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1) 132 #define CONFIG_SYS_I2C_ZYNQ 133 #endif 134 135 /* I2C */ 136 #if defined(CONFIG_SYS_I2C_ZYNQ) 137 # define CONFIG_SYS_I2C 138 # define CONFIG_SYS_I2C_ZYNQ_SPEED 100000 139 # define CONFIG_SYS_I2C_ZYNQ_SLAVE 0 140 #endif 141 142 /* EEPROM */ 143 #ifdef CONFIG_ZYNQ_EEPROM 144 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 145 # define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 146 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 147 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 148 # define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */ 149 #endif 150 151 /* Total Size of Environment Sector */ 152 #define CONFIG_ENV_SIZE (128 << 10) 153 154 /* Allow to overwrite serial and ethaddr */ 155 #define CONFIG_ENV_OVERWRITE 156 157 /* Environment */ 158 #ifndef CONFIG_ENV_IS_NOWHERE 159 # define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE 160 # define CONFIG_ENV_OFFSET 0xE0000 161 #endif 162 163 /* enable preboot to be loaded before CONFIG_BOOTDELAY */ 164 #define CONFIG_PREBOOT 165 166 /* Boot configuration */ 167 #define CONFIG_BOOTCOMMAND "run $modeboot || run distro_bootcmd" 168 #define CONFIG_SYS_LOAD_ADDR 0 /* default? */ 169 170 /* Distro boot enablement */ 171 172 #ifdef CONFIG_SPL_BUILD 173 #define BOOTENV 174 #else 175 #include <config_distro_defaults.h> 176 177 #ifdef CONFIG_CMD_MMC 178 #define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) 179 #else 180 #define BOOT_TARGET_DEVICES_MMC(func) 181 #endif 182 183 #ifdef CONFIG_CMD_USB 184 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) 185 #else 186 #define BOOT_TARGET_DEVICES_USB(func) 187 #endif 188 189 #if defined(CONFIG_CMD_PXE) 190 #define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na) 191 #else 192 #define BOOT_TARGET_DEVICES_PXE(func) 193 #endif 194 195 #if defined(CONFIG_CMD_DHCP) 196 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na) 197 #else 198 #define BOOT_TARGET_DEVICES_DHCP(func) 199 #endif 200 201 #define BOOT_TARGET_DEVICES(func) \ 202 BOOT_TARGET_DEVICES_MMC(func) \ 203 BOOT_TARGET_DEVICES_USB(func) \ 204 BOOT_TARGET_DEVICES_PXE(func) \ 205 BOOT_TARGET_DEVICES_DHCP(func) 206 207 #include <config_distro_bootcmd.h> 208 #endif /* CONFIG_SPL_BUILD */ 209 210 /* Default environment */ 211 #ifndef CONFIG_EXTRA_ENV_SETTINGS 212 #define CONFIG_EXTRA_ENV_SETTINGS \ 213 "fit_image=fit.itb\0" \ 214 "load_addr=0x2000000\0" \ 215 "fit_size=0x800000\0" \ 216 "flash_off=0x100000\0" \ 217 "nor_flash_off=0xE2100000\0" \ 218 "fdt_high=0x20000000\0" \ 219 "initrd_high=0x20000000\0" \ 220 "loadbootenv_addr=0x2000000\0" \ 221 "fdt_addr_r=0x1f00000\0" \ 222 "pxefile_addr_r=0x2000000\0" \ 223 "kernel_addr_r=0x2000000\0" \ 224 "scriptaddr=0x3000000\0" \ 225 "ramdisk_addr_r=0x3100000\0" \ 226 "bootenv=uEnv.txt\0" \ 227 "bootenv_dev=mmc\0" \ 228 "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \ 229 "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \ 230 "env import -t ${loadbootenv_addr} $filesize\0" \ 231 "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \ 232 "setbootenv=if env run bootenv_existence_test; then " \ 233 "if env run loadbootenv; then " \ 234 "env run importbootenv; " \ 235 "fi; " \ 236 "fi; \0" \ 237 "sd_loadbootenv=set bootenv_dev mmc && " \ 238 "run setbootenv \0" \ 239 "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \ 240 "preboot=if test $modeboot = sdboot; then " \ 241 "run sd_loadbootenv; " \ 242 "echo Checking if uenvcmd is set ...; " \ 243 "if test -n $uenvcmd; then " \ 244 "echo Running uenvcmd ...; " \ 245 "run uenvcmd; " \ 246 "fi; " \ 247 "fi; \0" \ 248 "norboot=echo Copying FIT from NOR flash to RAM... && " \ 249 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \ 250 "bootm ${load_addr}\0" \ 251 "sdboot=echo Copying FIT from SD to RAM... && " \ 252 "load mmc 0 ${load_addr} ${fit_image} && " \ 253 "bootm ${load_addr}\0" \ 254 "jtagboot=echo TFTPing FIT to RAM... && " \ 255 "tftpboot ${load_addr} ${fit_image} && " \ 256 "bootm ${load_addr}\0" \ 257 "usbboot=if usb start; then " \ 258 "echo Copying FIT from USB to RAM... && " \ 259 "load usb 0 ${load_addr} ${fit_image} && " \ 260 "bootm ${load_addr}; fi\0" \ 261 DFU_ALT_INFO \ 262 BOOTENV 263 #endif 264 265 /* Miscellaneous configurable options */ 266 267 #define CONFIG_CMDLINE_EDITING 268 #define CONFIG_AUTO_COMPLETE 269 #define CONFIG_SYS_LONGHELP 270 #define CONFIG_CLOCKS 271 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 272 273 #ifndef CONFIG_NR_DRAM_BANKS 274 # define CONFIG_NR_DRAM_BANKS 1 275 #endif 276 277 #define CONFIG_SYS_MEMTEST_START 0 278 #define CONFIG_SYS_MEMTEST_END 0x1000 279 280 #define CONFIG_SYS_MALLOC_LEN 0x1400000 281 282 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 283 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 284 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 285 CONFIG_SYS_INIT_RAM_SIZE - \ 286 GENERATED_GBL_DATA_SIZE) 287 288 /* Enable the PL to be downloaded */ 289 #define CONFIG_FPGA_ZYNQPL 290 291 /* FIT support */ 292 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */ 293 294 /* Extend size of kernel image for uncompression */ 295 #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024) 296 297 /* Boot FreeBSD/vxWorks from an ELF image */ 298 #define CONFIG_SYS_MMC_MAX_DEVICE 1 299 300 #define CONFIG_SYS_LDSCRIPT "arch/arm/mach-zynq/u-boot.lds" 301 302 /* Commands */ 303 304 /* SPL part */ 305 #define CONFIG_SPL_FRAMEWORK 306 307 /* MMC support */ 308 #ifdef CONFIG_MMC_SDHCI_ZYNQ 309 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 310 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 311 #endif 312 313 /* Disable dcache for SPL just for sure */ 314 #ifdef CONFIG_SPL_BUILD 315 #define CONFIG_SYS_DCACHE_OFF 316 #endif 317 318 /* Address in RAM where the parameters must be copied by SPL. */ 319 #define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000 320 321 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb" 322 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 323 324 /* Not using MMC raw mode - just for compilation purpose */ 325 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 326 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 327 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 328 329 /* qspi mode is working fine */ 330 #ifdef CONFIG_ZYNQ_QSPI 331 #define CONFIG_SPL_SPI_LOAD 332 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000 333 #define CONFIG_SYS_SPI_ARGS_OFFS 0x200000 334 #define CONFIG_SYS_SPI_ARGS_SIZE 0x80000 335 #define CONFIG_SYS_SPI_KERNEL_OFFS (CONFIG_SYS_SPI_ARGS_OFFS + \ 336 CONFIG_SYS_SPI_ARGS_SIZE) 337 #endif 338 339 /* for booting directly linux */ 340 341 /* SP location before relocation, must use scratch RAM */ 342 #define CONFIG_SPL_TEXT_BASE 0x0 343 344 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */ 345 #define CONFIG_SPL_MAX_SIZE 0x30000 346 347 /* On the top of OCM space */ 348 #define CONFIG_SYS_SPL_MALLOC_START CONFIG_SPL_STACK_R_ADDR 349 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000000 350 351 /* 352 * SPL stack position - and stack goes down 353 * 0xfffffe00 is used for putting wfi loop. 354 * Set it up as limit for now. 355 */ 356 #define CONFIG_SPL_STACK 0xfffffe00 357 358 /* BSS setup */ 359 #define CONFIG_SPL_BSS_START_ADDR 0x100000 360 #define CONFIG_SPL_BSS_MAX_SIZE 0x100000 361 362 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 363 364 #endif /* __CONFIG_ZYNQ_COMMON_H */ 365