1 /* 2 * Copyright (C) 2007-2013 Tensilica, Inc. 3 * Copyright (C) 2014 - 2016 Cadence Design Systems Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef __CONFIG_H 9 #define __CONFIG_H 10 11 #include <asm/arch/core.h> 12 #include <asm/addrspace.h> 13 #include <asm/config.h> 14 15 /* 16 * The 'xtfpga' board describes a set of very similar boards with only minimal 17 * differences. 18 */ 19 20 /*=====================*/ 21 /* Board and Processor */ 22 /*=====================*/ 23 24 #define CONFIG_XTFPGA 25 26 /* FPGA CPU freq after init */ 27 #define CONFIG_SYS_CLK_FREQ (gd->cpu_clk) 28 29 /*===================*/ 30 /* RAM Layout */ 31 /*===================*/ 32 33 #if XCHAL_HAVE_PTP_MMU 34 #define CONFIG_SYS_MEMORY_BASE \ 35 (XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR) 36 #define CONFIG_SYS_IO_BASE 0xf0000000 37 #else 38 #define CONFIG_SYS_MEMORY_BASE 0x60000000 39 #define CONFIG_SYS_IO_BASE 0x90000000 40 #define CONFIG_MAX_MEM_MAPPED 0x10000000 41 #endif 42 43 /* Onboard RAM sizes: 44 * 45 * LX60 0x04000000 64 MB 46 * LX110 0x03000000 48 MB 47 * LX200 0x06000000 96 MB 48 * ML605 0x18000000 384 MB 49 * KC705 0x38000000 896 MB 50 * 51 * noMMU configurations can only see first 256MB of onboard memory. 52 */ 53 54 #if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000 55 #define CONFIG_SYS_SDRAM_SIZE CONFIG_BOARD_SDRAM_SIZE 56 #else 57 #define CONFIG_SYS_SDRAM_SIZE 0x10000000 58 #endif 59 60 #define CONFIG_SYS_SDRAM_BASE MEMADDR(0x00000000) 61 62 /* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */ 63 #ifdef CONFIG_XTFPGA_LX60 64 # define CONFIG_SYS_MONITOR_LEN 0x00020000 /* 128KB */ 65 #else 66 # define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */ 67 #endif 68 69 #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* heap 256KB */ 70 71 /* Linux boot param area in RAM (used only when booting linux) */ 72 #define CONFIG_SYS_BOOTPARAMS_LEN (64 << 10) 73 74 /* Memory test is destructive so default must not overlap vectors or U-Boot*/ 75 #define CONFIG_SYS_MEMTEST_START MEMADDR(0x01000000) 76 #define CONFIG_SYS_MEMTEST_END MEMADDR(0x02000000) 77 78 /* Load address for stand-alone applications. 79 * MEMADDR cannot be used here, because the definition needs to be 80 * a plain number as it's used as -Ttext argument for ld in standalone 81 * example makefile. 82 * Handle noMMU vs MMUv2 vs MMUv3 distinction here manually. 83 */ 84 #if XCHAL_HAVE_PTP_MMU 85 #if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR 86 #define CONFIG_STANDALONE_LOAD_ADDR 0x00800000 87 #else 88 #define CONFIG_STANDALONE_LOAD_ADDR 0xd0800000 89 #endif 90 #else 91 #define CONFIG_STANDALONE_LOAD_ADDR 0x60800000 92 #endif 93 94 #if defined(CONFIG_MAX_MEM_MAPPED) && \ 95 CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE 96 #define CONFIG_SYS_MEMORY_SIZE CONFIG_MAX_MEM_MAPPED 97 #else 98 #define CONFIG_SYS_MEMORY_SIZE CONFIG_SYS_SDRAM_SIZE 99 #endif 100 101 #define CONFIG_SYS_MEMORY_TOP MEMADDR(CONFIG_SYS_MEMORY_SIZE) 102 #define CONFIG_SYS_TEXT_ADDR \ 103 (CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN) 104 105 /* Used by tftpboot; env var 'loadaddr' */ 106 #define CONFIG_SYS_LOAD_ADDR MEMADDR(0x02000000) 107 108 /*==============================*/ 109 /* U-Boot general configuration */ 110 /*==============================*/ 111 112 #define CONFIG_BOARD_POSTCLK_INIT 113 #define CONFIG_MISC_INIT_R 114 115 #define CONFIG_BOOTFILE "uImage" 116 /* Console I/O Buffer Size */ 117 #define CONFIG_SYS_CBSIZE 1024 118 /* Prt buf */ 119 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 120 sizeof(CONFIG_SYS_PROMPT) + 16) 121 /* max number of command args */ 122 #define CONFIG_SYS_MAXARGS 16 123 /* Boot Argument Buffer Size */ 124 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 125 126 /*==============================*/ 127 /* U-Boot autoboot configuration */ 128 /*==============================*/ 129 130 #define CONFIG_BOOT_RETRY_TIME 60 /* retry after 60 secs */ 131 132 #define CONFIG_AUTO_COMPLETE /* Support tab autocompletion */ 133 #define CONFIG_CMDLINE_EDITING 134 #define CONFIG_SYS_LONGHELP 135 #define CONFIG_MX_CYCLIC 136 #define CONFIG_SHOW_BOOT_PROGRESS 137 138 #ifdef DEBUG 139 #define CONFIG_PANIC_HANG 1 /* Require manual reboot */ 140 #endif 141 142 143 /*=========================================*/ 144 /* FPGA Registers (board info and control) */ 145 /*=========================================*/ 146 147 /* 148 * These assume FPGA bitstreams from Tensilica release RB and up. Earlier 149 * releases may not provide any/all of these registers or at these offsets. 150 * Some of the FPGA registers are broken down into bitfields described by 151 * SHIFT left amount and field WIDTH (bits), and also by a bitMASK. 152 */ 153 154 /* Date of FPGA bitstream build in binary coded decimal (BCD) */ 155 #define CONFIG_SYS_FPGAREG_DATE IOADDR(0x0D020000) 156 #define FPGAREG_MTH_SHIFT 24 /* BCD month 1..12 */ 157 #define FPGAREG_MTH_WIDTH 8 158 #define FPGAREG_MTH_MASK 0xFF000000 159 #define FPGAREG_DAY_SHIFT 16 /* BCD day 1..31 */ 160 #define FPGAREG_DAY_WIDTH 8 161 #define FPGAREG_DAY_MASK 0x00FF0000 162 #define FPGAREG_YEAR_SHIFT 0 /* BCD year 2001..9999*/ 163 #define FPGAREG_YEAR_WIDTH 16 164 #define FPGAREG_YEAR_MASK 0x0000FFFF 165 166 /* FPGA core clock frequency in Hz (also input to UART) */ 167 #define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004) /* CPU clock frequency*/ 168 169 /* 170 * DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1): 171 * Bits 0..5 set the lower 6 bits of the default ethernet MAC. 172 * Bit 6 is reserved for future use by Tensilica. 173 * Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to 174 * the base of flash * (when on/1) or to the base of RAM (when off/0). 175 */ 176 #define CONFIG_SYS_FPGAREG_DIPSW IOADDR(0x0D02000C) 177 #define FPGAREG_MAC_SHIFT 0 /* Ethernet MAC bits 0..5 */ 178 #define FPGAREG_MAC_WIDTH 6 179 #define FPGAREG_MAC_MASK 0x3f 180 #define FPGAREG_BOOT_SHIFT 7 /* Boot ROM addr mapping */ 181 #define FPGAREG_BOOT_WIDTH 1 182 #define FPGAREG_BOOT_MASK 0x80 183 #define FPGAREG_BOOT_RAM 0 184 #define FPGAREG_BOOT_FLASH (1<<FPGAREG_BOOT_SHIFT) 185 186 /* Force hard reset of board by writing a code to this register */ 187 #define CONFIG_SYS_FPGAREG_RESET IOADDR(0x0D020010) /* Reset board .. */ 188 #define CONFIG_SYS_FPGAREG_RESET_CODE 0x0000DEAD /* by writing this code */ 189 190 /*====================*/ 191 /* Serial Driver Info */ 192 /*====================*/ 193 194 #define CONFIG_SYS_NS16550_SERIAL 195 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 196 #define CONFIG_SYS_NS16550_COM1 IOADDR(0x0D050020) /* Base address */ 197 198 /* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */ 199 #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_CLK_FREQ 200 #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ 201 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 202 203 /*======================*/ 204 /* Ethernet Driver Info */ 205 /*======================*/ 206 207 #define CONFIG_ETHBASE 00:50:C2:13:6f:00 208 #define CONFIG_SYS_ETHOC_BASE IOADDR(0x0d030000) 209 #define CONFIG_SYS_ETHOC_BUFFER_ADDR IOADDR(0x0D800000) 210 211 /*=====================*/ 212 /* Flash & Environment */ 213 /*=====================*/ 214 215 #define CONFIG_SYS_FLASH_CFI 216 #define CONFIG_FLASH_CFI_DRIVER /* use generic CFI driver */ 217 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 218 #define CONFIG_SYS_MAX_FLASH_BANKS 1 219 #ifdef CONFIG_XTFPGA_LX60 220 # define CONFIG_SYS_FLASH_SIZE 0x0040000 /* 4MB */ 221 # define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* block size 64KB */ 222 # define CONFIG_SYS_FLASH_PARMSECT_SZ 0x2000 /* param size 8KB */ 223 # define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000) 224 # define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 225 #elif defined(CONFIG_XTFPGA_KC705) 226 # define CONFIG_SYS_FLASH_SIZE 0x8000000 /* 128MB */ 227 # define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */ 228 # define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */ 229 # define CONFIG_SYS_FLASH_BASE IOADDR(0x00000000) 230 # define CONFIG_SYS_MONITOR_BASE IOADDR(0x06000000) 231 #else 232 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* 16MB */ 233 # define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */ 234 # define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */ 235 # define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000) 236 # define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 237 #endif 238 #define CONFIG_SYS_MAX_FLASH_SECT \ 239 (CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \ 240 CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1) 241 #define CONFIG_SYS_FLASH_PROTECTION /* hw flash protection */ 242 243 /* 244 * Put environment in top block (64kB) 245 * Another option would be to put env. in 2nd param block offs 8KB, size 8KB 246 */ 247 #define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ) 248 #define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ 249 250 /* print 'E' for empty sector on flinfo */ 251 #define CONFIG_SYS_FLASH_EMPTY_INFO 252 253 #endif /* __CONFIG_H */ 254