1 /* 2 * Copyright 2010 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite550x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_BOOKE 1 /* BOOKE */ 18 #define CONFIG_E500 1 /* BOOKE e500 family */ 19 #define CONFIG_P2020 1 20 #define CONFIG_XPEDITE550X 1 21 #define CONFIG_SYS_BOARD_NAME "XPedite5500" 22 #define CONFIG_SYS_FORM_PMC_XMC 1 23 #define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */ 24 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 25 #define CONFIG_SYS_GENERIC_BOARD 26 #define CONFIG_DISPLAY_BOARDINFO 27 28 #ifndef CONFIG_SYS_TEXT_BASE 29 #define CONFIG_SYS_TEXT_BASE 0xfff80000 30 #endif 31 32 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 33 #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ 34 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 35 #define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */ 36 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 37 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 38 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 39 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 40 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 41 #define CONFIG_FSL_ELBC 1 42 43 /* 44 * Multicore config 45 */ 46 #define CONFIG_MP 47 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 48 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 49 50 /* 51 * DDR config 52 */ 53 #define CONFIG_SYS_FSL_DDR3 54 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 55 #define CONFIG_DDR_SPD 56 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 57 #define SPD_EEPROM_ADDRESS 0x54 58 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 59 #define CONFIG_NUM_DDR_CONTROLLERS 1 60 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 61 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 62 #define CONFIG_DDR_ECC 63 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 64 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 65 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 66 #define CONFIG_VERY_BIG_RAM 67 68 #ifndef __ASSEMBLY__ 69 extern unsigned long get_board_sys_clk(unsigned long dummy); 70 extern unsigned long get_board_ddr_clk(unsigned long dummy); 71 #endif 72 73 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 74 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 75 76 /* 77 * These can be toggled for performance analysis, otherwise use default. 78 */ 79 #define CONFIG_L2_CACHE /* toggle L2 cache */ 80 #define CONFIG_BTB /* toggle branch predition */ 81 #define CONFIG_ENABLE_36BIT_PHYS 1 82 83 #define CONFIG_SYS_CCSRBAR 0xef000000 84 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 85 86 /* 87 * Diagnostics 88 */ 89 #define CONFIG_SYS_ALT_MEMTEST 90 #define CONFIG_SYS_MEMTEST_START 0x10000000 91 #define CONFIG_SYS_MEMTEST_END 0x20000000 92 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 93 CONFIG_SYS_POST_I2C) 94 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \ 95 CONFIG_SYS_I2C_LM75_ADDR, \ 96 CONFIG_SYS_I2C_LM90_ADDR, \ 97 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 98 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 99 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 100 CONFIG_SYS_I2C_RTC_ADDR} 101 102 /* 103 * Memory map 104 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 105 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 106 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 107 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 108 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 109 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 110 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 111 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 112 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 113 */ 114 115 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 116 117 /* 118 * NAND flash configuration 119 */ 120 #define CONFIG_SYS_NAND_BASE 0xef800000 121 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 122 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 123 CONFIG_SYS_NAND_BASE2} 124 #define CONFIG_SYS_MAX_NAND_DEVICE 2 125 #define CONFIG_MTD_NAND_VERIFY_WRITE 126 #define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */ 127 #define CONFIG_NAND_FSL_ELBC 128 129 /* 130 * NOR flash configuration 131 */ 132 #define CONFIG_SYS_FLASH_BASE 0xf8000000 133 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 134 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 135 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 136 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 137 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 138 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 139 #define CONFIG_FLASH_CFI_DRIVER 140 #define CONFIG_SYS_FLASH_CFI 141 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 142 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 143 {0xf7f40000, 0xc0000} } 144 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 145 146 /* 147 * Chip select configuration 148 */ 149 /* NOR Flash 0 on CS0 */ 150 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 151 BR_PS_16 | \ 152 BR_V) 153 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 154 OR_GPCM_CSNT | \ 155 OR_GPCM_XACS | \ 156 OR_GPCM_ACS_DIV2 | \ 157 OR_GPCM_SCY_8 | \ 158 OR_GPCM_TRLX | \ 159 OR_GPCM_EHTR | \ 160 OR_GPCM_EAD) 161 162 /* NOR Flash 1 on CS1 */ 163 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 164 BR_PS_16 | \ 165 BR_V) 166 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 167 168 /* NAND flash on CS2 */ 169 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 170 (2<<BR_DECC_SHIFT) | \ 171 BR_PS_8 | \ 172 BR_MS_FCM | \ 173 BR_V) 174 175 /* NAND flash on CS2 */ 176 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 177 OR_FCM_PGS | \ 178 OR_FCM_CSCT | \ 179 OR_FCM_CST | \ 180 OR_FCM_CHT | \ 181 OR_FCM_SCY_1 | \ 182 OR_FCM_TRLX | \ 183 OR_FCM_EHTR) 184 185 /* NAND flash on CS3 */ 186 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 187 (2<<BR_DECC_SHIFT) | \ 188 BR_PS_8 | \ 189 BR_MS_FCM | \ 190 BR_V) 191 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 192 193 /* 194 * Use L1 as initial stack 195 */ 196 #define CONFIG_SYS_INIT_RAM_LOCK 1 197 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 198 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 199 200 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 201 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 202 203 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 204 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 205 206 /* 207 * Serial Port 208 */ 209 #define CONFIG_CONS_INDEX 1 210 #define CONFIG_SYS_NS16550 211 #define CONFIG_SYS_NS16550_SERIAL 212 #define CONFIG_SYS_NS16550_REG_SIZE 1 213 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 214 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 215 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 216 #define CONFIG_SYS_BAUDRATE_TABLE \ 217 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 218 #define CONFIG_BAUDRATE 115200 219 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 220 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 221 222 /* 223 * Use the HUSH parser 224 */ 225 #define CONFIG_SYS_HUSH_PARSER 226 227 /* 228 * Pass open firmware flat tree 229 */ 230 #define CONFIG_OF_LIBFDT 1 231 #define CONFIG_OF_BOARD_SETUP 1 232 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 233 #define CONFIG_FDT_FIXUP_PCI_IRQ 1 234 235 /* 236 * I2C 237 */ 238 #define CONFIG_SYS_I2C 239 #define CONFIG_SYS_I2C_FSL 240 #define CONFIG_SYS_FSL_I2C_SPEED 400000 241 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 242 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 243 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 244 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 245 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 246 247 /* I2C DS7505 temperature sensor */ 248 #define CONFIG_DTT_LM75 249 #define CONFIG_DTT_SENSORS { 0 } 250 #define CONFIG_SYS_I2C_LM75_ADDR 0x48 251 252 /* I2C ADT7461 temperature sensor */ 253 #define CONFIG_SYS_I2C_LM90_ADDR 0x4C 254 255 /* I2C EEPROM - AT24C128B */ 256 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 257 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 258 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 259 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 260 261 /* I2C RTC */ 262 #define CONFIG_RTC_M41T11 1 263 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 264 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 265 266 /* GPIO */ 267 #define CONFIG_PCA953X 268 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 269 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 270 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 271 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 272 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 273 274 /* 275 * GPIO pin definitions, PU = pulled high, PD = pulled low 276 */ 277 /* PCA9557 @ 0x18*/ 278 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 279 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */ 280 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 281 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */ 282 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 283 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */ 284 285 /* PCA9557 @ 0x1e*/ 286 #define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */ 287 #define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */ 288 #define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */ 289 #define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */ 290 #define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */ 291 #define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */ 292 #define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */ 293 294 /* PCA9557 @ 0x1f */ 295 #define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */ 296 #define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */ 297 #define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */ 298 #define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */ 299 #define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */ 300 #define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */ 301 #define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */ 302 #define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */ 303 304 /* 305 * General PCI 306 * Memory space is mapped 1-1, but I/O space must start from 0. 307 */ 308 309 /* controller 1 - PEX8112 or XMC, depending on build option */ 310 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 311 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 312 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 313 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 314 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 315 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 316 317 318 /* 319 * Networking options 320 */ 321 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 322 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 323 #define CONFIG_TSEC_TBI 324 #define CONFIG_MII 1 /* MII PHY management */ 325 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 326 #define CONFIG_ETHPRIME "eTSEC2" 327 328 /* 329 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 330 * 1000mbps SGMII link 331 */ 332 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 333 TBICR_PHY_RESET \ 334 | TBICR_FULL_DUPLEX \ 335 | TBICR_SPEED1_SET \ 336 ) 337 338 #define CONFIG_TSEC1 1 339 #define CONFIG_TSEC1_NAME "eTSEC1" 340 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 341 #define TSEC1_PHY_ADDR 1 342 #define TSEC1_PHYIDX 0 343 #define CONFIG_HAS_ETH0 344 345 #define CONFIG_TSEC2 1 346 #define CONFIG_TSEC2_NAME "eTSEC2" 347 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 348 #define TSEC2_PHY_ADDR 2 349 #define TSEC2_PHYIDX 0 350 #define CONFIG_HAS_ETH1 351 352 #define CONFIG_TSEC3 1 353 #define CONFIG_TSEC3_NAME "eTSEC3" 354 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 355 #define TSEC3_PHY_ADDR 3 356 #define TSEC3_PHYIDX 0 357 #define CONFIG_HAS_ETH2 358 359 /* 360 * USB 361 */ 362 #define CONFIG_USB_STORAGE 363 #define CONFIG_USB_EHCI 364 #define CONFIG_USB_EHCI_FSL 365 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 366 #define CONFIG_DOS_PARTITION 367 368 /* 369 * Command configuration. 370 */ 371 #include <config_cmd_default.h> 372 373 #define CONFIG_CMD_ASKENV 374 #define CONFIG_CMD_DATE 375 #define CONFIG_CMD_DHCP 376 #define CONFIG_CMD_DTT 377 #define CONFIG_CMD_EEPROM 378 #define CONFIG_CMD_ELF 379 #define CONFIG_CMD_FLASH 380 #define CONFIG_CMD_I2C 381 #define CONFIG_CMD_JFFS2 382 #define CONFIG_CMD_MII 383 #define CONFIG_CMD_NAND 384 #define CONFIG_CMD_NET 385 #define CONFIG_CMD_PCA953X 386 #define CONFIG_CMD_PCA953X_INFO 387 #define CONFIG_CMD_PCI 388 #define CONFIG_CMD_PCI_ENUM 389 #define CONFIG_CMD_PING 390 #define CONFIG_CMD_REGINFO 391 #define CONFIG_CMD_SAVEENV 392 #define CONFIG_CMD_SNTP 393 #define CONFIG_CMD_USB 394 395 /* 396 * Miscellaneous configurable options 397 */ 398 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 399 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 400 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 401 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 402 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 403 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 404 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 405 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 406 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 407 #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ 408 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 409 #define CONFIG_PREBOOT /* enable preboot variable */ 410 #define CONFIG_FIT 1 411 #define CONFIG_FIT_VERBOSE 1 412 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 413 414 /* 415 * For booting Linux, the board info and command line data 416 * have to be in the first 16 MB of memory, since this is 417 * the maximum mapped by the Linux kernel during initialization. 418 */ 419 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 420 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 421 422 /* 423 * Environment Configuration 424 */ 425 #define CONFIG_ENV_IS_IN_FLASH 1 426 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 427 #define CONFIG_ENV_SIZE 0x8000 428 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 429 430 /* 431 * Flash memory map: 432 * fff80000 - ffffffff Pri U-Boot (512 KB) 433 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 434 * fff00000 - fff3ffff Pri FDT (256KB) 435 * fef00000 - ffefffff Pri OS image (16MB) 436 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 437 * 438 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 439 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 440 * f7f00000 - f7f3ffff Sec FDT (256KB) 441 * f6f00000 - f7efffff Sec OS image (16MB) 442 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 443 */ 444 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 445 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 446 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 447 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 448 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 449 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 450 451 #define CONFIG_PROG_UBOOT1 \ 452 "$download_cmd $loadaddr $ubootfile; " \ 453 "if test $? -eq 0; then " \ 454 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 455 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 456 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 457 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 458 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 459 "if test $? -ne 0; then " \ 460 "echo PROGRAM FAILED; " \ 461 "else; " \ 462 "echo PROGRAM SUCCEEDED; " \ 463 "fi; " \ 464 "else; " \ 465 "echo DOWNLOAD FAILED; " \ 466 "fi;" 467 468 #define CONFIG_PROG_UBOOT2 \ 469 "$download_cmd $loadaddr $ubootfile; " \ 470 "if test $? -eq 0; then " \ 471 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 472 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 473 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 474 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 475 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 476 "if test $? -ne 0; then " \ 477 "echo PROGRAM FAILED; " \ 478 "else; " \ 479 "echo PROGRAM SUCCEEDED; " \ 480 "fi; " \ 481 "else; " \ 482 "echo DOWNLOAD FAILED; " \ 483 "fi;" 484 485 #define CONFIG_BOOT_OS_NET \ 486 "$download_cmd $osaddr $osfile; " \ 487 "if test $? -eq 0; then " \ 488 "if test -n $fdtaddr; then " \ 489 "$download_cmd $fdtaddr $fdtfile; " \ 490 "if test $? -eq 0; then " \ 491 "bootm $osaddr - $fdtaddr; " \ 492 "else; " \ 493 "echo FDT DOWNLOAD FAILED; " \ 494 "fi; " \ 495 "else; " \ 496 "bootm $osaddr; " \ 497 "fi; " \ 498 "else; " \ 499 "echo OS DOWNLOAD FAILED; " \ 500 "fi;" 501 502 #define CONFIG_PROG_OS1 \ 503 "$download_cmd $osaddr $osfile; " \ 504 "if test $? -eq 0; then " \ 505 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 506 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 507 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 508 "if test $? -ne 0; then " \ 509 "echo OS PROGRAM FAILED; " \ 510 "else; " \ 511 "echo OS PROGRAM SUCCEEDED; " \ 512 "fi; " \ 513 "else; " \ 514 "echo OS DOWNLOAD FAILED; " \ 515 "fi;" 516 517 #define CONFIG_PROG_OS2 \ 518 "$download_cmd $osaddr $osfile; " \ 519 "if test $? -eq 0; then " \ 520 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 521 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 522 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 523 "if test $? -ne 0; then " \ 524 "echo OS PROGRAM FAILED; " \ 525 "else; " \ 526 "echo OS PROGRAM SUCCEEDED; " \ 527 "fi; " \ 528 "else; " \ 529 "echo OS DOWNLOAD FAILED; " \ 530 "fi;" 531 532 #define CONFIG_PROG_FDT1 \ 533 "$download_cmd $fdtaddr $fdtfile; " \ 534 "if test $? -eq 0; then " \ 535 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 536 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 537 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 538 "if test $? -ne 0; then " \ 539 "echo FDT PROGRAM FAILED; " \ 540 "else; " \ 541 "echo FDT PROGRAM SUCCEEDED; " \ 542 "fi; " \ 543 "else; " \ 544 "echo FDT DOWNLOAD FAILED; " \ 545 "fi;" 546 547 #define CONFIG_PROG_FDT2 \ 548 "$download_cmd $fdtaddr $fdtfile; " \ 549 "if test $? -eq 0; then " \ 550 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 551 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 552 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 553 "if test $? -ne 0; then " \ 554 "echo FDT PROGRAM FAILED; " \ 555 "else; " \ 556 "echo FDT PROGRAM SUCCEEDED; " \ 557 "fi; " \ 558 "else; " \ 559 "echo FDT DOWNLOAD FAILED; " \ 560 "fi;" 561 562 #define CONFIG_EXTRA_ENV_SETTINGS \ 563 "autoload=yes\0" \ 564 "download_cmd=tftp\0" \ 565 "console_args=console=ttyS0,115200\0" \ 566 "root_args=root=/dev/nfs rw\0" \ 567 "misc_args=ip=on\0" \ 568 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 569 "bootfile=/home/user/file\0" \ 570 "osfile=/home/user/board.uImage\0" \ 571 "fdtfile=/home/user/board.dtb\0" \ 572 "ubootfile=/home/user/u-boot.bin\0" \ 573 "fdtaddr=c00000\0" \ 574 "osaddr=0x1000000\0" \ 575 "loadaddr=0x1000000\0" \ 576 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 577 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 578 "prog_os1="CONFIG_PROG_OS1"\0" \ 579 "prog_os2="CONFIG_PROG_OS2"\0" \ 580 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 581 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 582 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 583 "bootcmd_flash1=run set_bootargs; " \ 584 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 585 "bootcmd_flash2=run set_bootargs; " \ 586 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 587 "bootcmd=run bootcmd_flash1\0" 588 #endif /* __CONFIG_H */ 589