1 /* 2 * Copyright 2010 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite550x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_BOOKE 1 /* BOOKE */ 18 #define CONFIG_E500 1 /* BOOKE e500 family */ 19 #define CONFIG_P2020 1 20 #define CONFIG_XPEDITE550X 1 21 #define CONFIG_SYS_BOARD_NAME "XPedite5500" 22 #define CONFIG_SYS_FORM_PMC_XMC 1 23 #define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */ 24 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 25 #define CONFIG_SYS_GENERIC_BOARD 26 #define CONFIG_DISPLAY_BOARDINFO 27 28 #ifndef CONFIG_SYS_TEXT_BASE 29 #define CONFIG_SYS_TEXT_BASE 0xfff80000 30 #endif 31 32 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 33 #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ 34 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 35 #define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */ 36 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 37 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 38 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 39 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 40 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 41 #define CONFIG_FSL_ELBC 1 42 43 /* 44 * Multicore config 45 */ 46 #define CONFIG_MP 47 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 48 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 49 50 /* 51 * DDR config 52 */ 53 #define CONFIG_SYS_FSL_DDR3 54 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 55 #define CONFIG_DDR_SPD 56 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 57 #define SPD_EEPROM_ADDRESS 0x54 58 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 59 #define CONFIG_NUM_DDR_CONTROLLERS 1 60 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 61 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 62 #define CONFIG_DDR_ECC 63 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 64 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 65 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 66 #define CONFIG_VERY_BIG_RAM 67 68 #ifndef __ASSEMBLY__ 69 extern unsigned long get_board_sys_clk(unsigned long dummy); 70 extern unsigned long get_board_ddr_clk(unsigned long dummy); 71 #endif 72 73 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 74 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 75 76 /* 77 * These can be toggled for performance analysis, otherwise use default. 78 */ 79 #define CONFIG_L2_CACHE /* toggle L2 cache */ 80 #define CONFIG_BTB /* toggle branch predition */ 81 #define CONFIG_ENABLE_36BIT_PHYS 1 82 83 #define CONFIG_SYS_CCSRBAR 0xef000000 84 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 85 86 /* 87 * Diagnostics 88 */ 89 #define CONFIG_SYS_ALT_MEMTEST 90 #define CONFIG_SYS_MEMTEST_START 0x10000000 91 #define CONFIG_SYS_MEMTEST_END 0x20000000 92 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 93 CONFIG_SYS_POST_I2C) 94 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \ 95 CONFIG_SYS_I2C_LM75_ADDR, \ 96 CONFIG_SYS_I2C_LM90_ADDR, \ 97 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 98 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 99 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 100 CONFIG_SYS_I2C_RTC_ADDR} 101 102 /* 103 * Memory map 104 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 105 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 106 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 107 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 108 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 109 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 110 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 111 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 112 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 113 */ 114 115 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 116 117 /* 118 * NAND flash configuration 119 */ 120 #define CONFIG_SYS_NAND_BASE 0xef800000 121 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 122 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 123 CONFIG_SYS_NAND_BASE2} 124 #define CONFIG_SYS_MAX_NAND_DEVICE 2 125 #define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */ 126 #define CONFIG_NAND_FSL_ELBC 127 128 /* 129 * NOR flash configuration 130 */ 131 #define CONFIG_SYS_FLASH_BASE 0xf8000000 132 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 133 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 134 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 135 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 136 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 137 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 138 #define CONFIG_FLASH_CFI_DRIVER 139 #define CONFIG_SYS_FLASH_CFI 140 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 141 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 142 {0xf7f40000, 0xc0000} } 143 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 144 145 /* 146 * Chip select configuration 147 */ 148 /* NOR Flash 0 on CS0 */ 149 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 150 BR_PS_16 | \ 151 BR_V) 152 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 153 OR_GPCM_CSNT | \ 154 OR_GPCM_XACS | \ 155 OR_GPCM_ACS_DIV2 | \ 156 OR_GPCM_SCY_8 | \ 157 OR_GPCM_TRLX | \ 158 OR_GPCM_EHTR | \ 159 OR_GPCM_EAD) 160 161 /* NOR Flash 1 on CS1 */ 162 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 163 BR_PS_16 | \ 164 BR_V) 165 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 166 167 /* NAND flash on CS2 */ 168 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 169 (2<<BR_DECC_SHIFT) | \ 170 BR_PS_8 | \ 171 BR_MS_FCM | \ 172 BR_V) 173 174 /* NAND flash on CS2 */ 175 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 176 OR_FCM_PGS | \ 177 OR_FCM_CSCT | \ 178 OR_FCM_CST | \ 179 OR_FCM_CHT | \ 180 OR_FCM_SCY_1 | \ 181 OR_FCM_TRLX | \ 182 OR_FCM_EHTR) 183 184 /* NAND flash on CS3 */ 185 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 186 (2<<BR_DECC_SHIFT) | \ 187 BR_PS_8 | \ 188 BR_MS_FCM | \ 189 BR_V) 190 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 191 192 /* 193 * Use L1 as initial stack 194 */ 195 #define CONFIG_SYS_INIT_RAM_LOCK 1 196 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 197 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 198 199 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 200 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 201 202 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 203 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 204 205 /* 206 * Serial Port 207 */ 208 #define CONFIG_CONS_INDEX 1 209 #define CONFIG_SYS_NS16550 210 #define CONFIG_SYS_NS16550_SERIAL 211 #define CONFIG_SYS_NS16550_REG_SIZE 1 212 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 213 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 214 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 215 #define CONFIG_SYS_BAUDRATE_TABLE \ 216 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 217 #define CONFIG_BAUDRATE 115200 218 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 219 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 220 221 /* 222 * Use the HUSH parser 223 */ 224 #define CONFIG_SYS_HUSH_PARSER 225 226 /* 227 * Pass open firmware flat tree 228 */ 229 #define CONFIG_OF_LIBFDT 1 230 #define CONFIG_OF_BOARD_SETUP 1 231 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 232 #define CONFIG_FDT_FIXUP_PCI_IRQ 1 233 234 /* 235 * I2C 236 */ 237 #define CONFIG_SYS_I2C 238 #define CONFIG_SYS_I2C_FSL 239 #define CONFIG_SYS_FSL_I2C_SPEED 400000 240 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 241 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 242 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 243 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 244 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 245 246 /* I2C DS7505 temperature sensor */ 247 #define CONFIG_DTT_LM75 248 #define CONFIG_DTT_SENSORS { 0 } 249 #define CONFIG_SYS_I2C_LM75_ADDR 0x48 250 251 /* I2C ADT7461 temperature sensor */ 252 #define CONFIG_SYS_I2C_LM90_ADDR 0x4C 253 254 /* I2C EEPROM - AT24C128B */ 255 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 256 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 257 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 258 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 259 260 /* I2C RTC */ 261 #define CONFIG_RTC_M41T11 1 262 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 263 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 264 265 /* GPIO */ 266 #define CONFIG_PCA953X 267 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 268 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 269 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 270 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 271 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 272 273 /* 274 * GPIO pin definitions, PU = pulled high, PD = pulled low 275 */ 276 /* PCA9557 @ 0x18*/ 277 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 278 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */ 279 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 280 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */ 281 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 282 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */ 283 284 /* PCA9557 @ 0x1e*/ 285 #define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */ 286 #define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */ 287 #define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */ 288 #define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */ 289 #define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */ 290 #define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */ 291 #define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */ 292 293 /* PCA9557 @ 0x1f */ 294 #define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */ 295 #define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */ 296 #define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */ 297 #define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */ 298 #define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */ 299 #define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */ 300 #define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */ 301 #define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */ 302 303 /* 304 * General PCI 305 * Memory space is mapped 1-1, but I/O space must start from 0. 306 */ 307 308 /* controller 1 - PEX8112 or XMC, depending on build option */ 309 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 310 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 311 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 312 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 313 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 314 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 315 316 317 /* 318 * Networking options 319 */ 320 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 321 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 322 #define CONFIG_TSEC_TBI 323 #define CONFIG_MII 1 /* MII PHY management */ 324 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 325 #define CONFIG_ETHPRIME "eTSEC2" 326 327 /* 328 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 329 * 1000mbps SGMII link 330 */ 331 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 332 TBICR_PHY_RESET \ 333 | TBICR_FULL_DUPLEX \ 334 | TBICR_SPEED1_SET \ 335 ) 336 337 #define CONFIG_TSEC1 1 338 #define CONFIG_TSEC1_NAME "eTSEC1" 339 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 340 #define TSEC1_PHY_ADDR 1 341 #define TSEC1_PHYIDX 0 342 #define CONFIG_HAS_ETH0 343 344 #define CONFIG_TSEC2 1 345 #define CONFIG_TSEC2_NAME "eTSEC2" 346 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 347 #define TSEC2_PHY_ADDR 2 348 #define TSEC2_PHYIDX 0 349 #define CONFIG_HAS_ETH1 350 351 #define CONFIG_TSEC3 1 352 #define CONFIG_TSEC3_NAME "eTSEC3" 353 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 354 #define TSEC3_PHY_ADDR 3 355 #define TSEC3_PHYIDX 0 356 #define CONFIG_HAS_ETH2 357 358 /* 359 * USB 360 */ 361 #define CONFIG_USB_STORAGE 362 #define CONFIG_USB_EHCI 363 #define CONFIG_USB_EHCI_FSL 364 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 365 #define CONFIG_DOS_PARTITION 366 367 /* 368 * Command configuration. 369 */ 370 #include <config_cmd_default.h> 371 372 #define CONFIG_CMD_ASKENV 373 #define CONFIG_CMD_DATE 374 #define CONFIG_CMD_DHCP 375 #define CONFIG_CMD_DTT 376 #define CONFIG_CMD_EEPROM 377 #define CONFIG_CMD_ELF 378 #define CONFIG_CMD_FLASH 379 #define CONFIG_CMD_I2C 380 #define CONFIG_CMD_JFFS2 381 #define CONFIG_CMD_MII 382 #define CONFIG_CMD_NAND 383 #define CONFIG_CMD_NET 384 #define CONFIG_CMD_PCA953X 385 #define CONFIG_CMD_PCA953X_INFO 386 #define CONFIG_CMD_PCI 387 #define CONFIG_CMD_PCI_ENUM 388 #define CONFIG_CMD_PING 389 #define CONFIG_CMD_REGINFO 390 #define CONFIG_CMD_SAVEENV 391 #define CONFIG_CMD_SNTP 392 #define CONFIG_CMD_USB 393 394 /* 395 * Miscellaneous configurable options 396 */ 397 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 398 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 399 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 400 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 401 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 402 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 403 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 404 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 405 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 406 #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ 407 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 408 #define CONFIG_PREBOOT /* enable preboot variable */ 409 #define CONFIG_FIT 1 410 #define CONFIG_FIT_VERBOSE 1 411 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 412 413 /* 414 * For booting Linux, the board info and command line data 415 * have to be in the first 16 MB of memory, since this is 416 * the maximum mapped by the Linux kernel during initialization. 417 */ 418 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 419 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 420 421 /* 422 * Environment Configuration 423 */ 424 #define CONFIG_ENV_IS_IN_FLASH 1 425 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 426 #define CONFIG_ENV_SIZE 0x8000 427 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 428 429 /* 430 * Flash memory map: 431 * fff80000 - ffffffff Pri U-Boot (512 KB) 432 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 433 * fff00000 - fff3ffff Pri FDT (256KB) 434 * fef00000 - ffefffff Pri OS image (16MB) 435 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 436 * 437 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 438 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 439 * f7f00000 - f7f3ffff Sec FDT (256KB) 440 * f6f00000 - f7efffff Sec OS image (16MB) 441 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 442 */ 443 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 444 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 445 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 446 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 447 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 448 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 449 450 #define CONFIG_PROG_UBOOT1 \ 451 "$download_cmd $loadaddr $ubootfile; " \ 452 "if test $? -eq 0; then " \ 453 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 454 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 455 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 456 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 457 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 458 "if test $? -ne 0; then " \ 459 "echo PROGRAM FAILED; " \ 460 "else; " \ 461 "echo PROGRAM SUCCEEDED; " \ 462 "fi; " \ 463 "else; " \ 464 "echo DOWNLOAD FAILED; " \ 465 "fi;" 466 467 #define CONFIG_PROG_UBOOT2 \ 468 "$download_cmd $loadaddr $ubootfile; " \ 469 "if test $? -eq 0; then " \ 470 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 471 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 472 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 473 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 474 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 475 "if test $? -ne 0; then " \ 476 "echo PROGRAM FAILED; " \ 477 "else; " \ 478 "echo PROGRAM SUCCEEDED; " \ 479 "fi; " \ 480 "else; " \ 481 "echo DOWNLOAD FAILED; " \ 482 "fi;" 483 484 #define CONFIG_BOOT_OS_NET \ 485 "$download_cmd $osaddr $osfile; " \ 486 "if test $? -eq 0; then " \ 487 "if test -n $fdtaddr; then " \ 488 "$download_cmd $fdtaddr $fdtfile; " \ 489 "if test $? -eq 0; then " \ 490 "bootm $osaddr - $fdtaddr; " \ 491 "else; " \ 492 "echo FDT DOWNLOAD FAILED; " \ 493 "fi; " \ 494 "else; " \ 495 "bootm $osaddr; " \ 496 "fi; " \ 497 "else; " \ 498 "echo OS DOWNLOAD FAILED; " \ 499 "fi;" 500 501 #define CONFIG_PROG_OS1 \ 502 "$download_cmd $osaddr $osfile; " \ 503 "if test $? -eq 0; then " \ 504 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 505 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 506 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 507 "if test $? -ne 0; then " \ 508 "echo OS PROGRAM FAILED; " \ 509 "else; " \ 510 "echo OS PROGRAM SUCCEEDED; " \ 511 "fi; " \ 512 "else; " \ 513 "echo OS DOWNLOAD FAILED; " \ 514 "fi;" 515 516 #define CONFIG_PROG_OS2 \ 517 "$download_cmd $osaddr $osfile; " \ 518 "if test $? -eq 0; then " \ 519 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 520 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 521 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 522 "if test $? -ne 0; then " \ 523 "echo OS PROGRAM FAILED; " \ 524 "else; " \ 525 "echo OS PROGRAM SUCCEEDED; " \ 526 "fi; " \ 527 "else; " \ 528 "echo OS DOWNLOAD FAILED; " \ 529 "fi;" 530 531 #define CONFIG_PROG_FDT1 \ 532 "$download_cmd $fdtaddr $fdtfile; " \ 533 "if test $? -eq 0; then " \ 534 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 535 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 536 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 537 "if test $? -ne 0; then " \ 538 "echo FDT PROGRAM FAILED; " \ 539 "else; " \ 540 "echo FDT PROGRAM SUCCEEDED; " \ 541 "fi; " \ 542 "else; " \ 543 "echo FDT DOWNLOAD FAILED; " \ 544 "fi;" 545 546 #define CONFIG_PROG_FDT2 \ 547 "$download_cmd $fdtaddr $fdtfile; " \ 548 "if test $? -eq 0; then " \ 549 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 550 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 551 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 552 "if test $? -ne 0; then " \ 553 "echo FDT PROGRAM FAILED; " \ 554 "else; " \ 555 "echo FDT PROGRAM SUCCEEDED; " \ 556 "fi; " \ 557 "else; " \ 558 "echo FDT DOWNLOAD FAILED; " \ 559 "fi;" 560 561 #define CONFIG_EXTRA_ENV_SETTINGS \ 562 "autoload=yes\0" \ 563 "download_cmd=tftp\0" \ 564 "console_args=console=ttyS0,115200\0" \ 565 "root_args=root=/dev/nfs rw\0" \ 566 "misc_args=ip=on\0" \ 567 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 568 "bootfile=/home/user/file\0" \ 569 "osfile=/home/user/board.uImage\0" \ 570 "fdtfile=/home/user/board.dtb\0" \ 571 "ubootfile=/home/user/u-boot.bin\0" \ 572 "fdtaddr=c00000\0" \ 573 "osaddr=0x1000000\0" \ 574 "loadaddr=0x1000000\0" \ 575 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 576 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 577 "prog_os1="CONFIG_PROG_OS1"\0" \ 578 "prog_os2="CONFIG_PROG_OS2"\0" \ 579 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 580 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 581 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 582 "bootcmd_flash1=run set_bootargs; " \ 583 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 584 "bootcmd_flash2=run set_bootargs; " \ 585 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 586 "bootcmd=run bootcmd_flash1\0" 587 #endif /* __CONFIG_H */ 588