1 /* 2 * Copyright 2010 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite550x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_XPEDITE550X 1 18 #define CONFIG_SYS_BOARD_NAME "XPedite5500" 19 #define CONFIG_SYS_FORM_PMC_XMC 1 20 #define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */ 21 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 22 23 #ifndef CONFIG_SYS_TEXT_BASE 24 #define CONFIG_SYS_TEXT_BASE 0xfff80000 25 #endif 26 27 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 28 #define CONFIG_PCIE1 1 /* PCIE controller 1 (PEX8112 or XMC) */ 29 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 30 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 31 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 32 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 33 34 /* 35 * Multicore config 36 */ 37 #define CONFIG_MP 38 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 39 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 40 41 /* 42 * DDR config 43 */ 44 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 45 #define CONFIG_DDR_SPD 46 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 47 #define SPD_EEPROM_ADDRESS 0x54 48 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 49 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 50 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 51 #define CONFIG_DDR_ECC 52 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 53 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 54 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 55 #define CONFIG_VERY_BIG_RAM 56 57 #ifndef __ASSEMBLY__ 58 extern unsigned long get_board_sys_clk(unsigned long dummy); 59 extern unsigned long get_board_ddr_clk(unsigned long dummy); 60 #endif 61 62 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 63 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 64 65 /* 66 * These can be toggled for performance analysis, otherwise use default. 67 */ 68 #define CONFIG_L2_CACHE /* toggle L2 cache */ 69 #define CONFIG_BTB /* toggle branch predition */ 70 #define CONFIG_ENABLE_36BIT_PHYS 1 71 72 #define CONFIG_SYS_CCSRBAR 0xef000000 73 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 74 75 /* 76 * Diagnostics 77 */ 78 #define CONFIG_SYS_ALT_MEMTEST 79 #define CONFIG_SYS_MEMTEST_START 0x10000000 80 #define CONFIG_SYS_MEMTEST_END 0x20000000 81 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 82 CONFIG_SYS_POST_I2C) 83 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \ 84 CONFIG_SYS_I2C_LM75_ADDR, \ 85 CONFIG_SYS_I2C_LM90_ADDR, \ 86 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 87 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 88 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 89 CONFIG_SYS_I2C_RTC_ADDR} 90 91 /* 92 * Memory map 93 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 94 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 95 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 96 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 97 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 98 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 99 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 100 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 101 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 102 */ 103 104 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 105 106 /* 107 * NAND flash configuration 108 */ 109 #define CONFIG_SYS_NAND_BASE 0xef800000 110 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 111 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 112 CONFIG_SYS_NAND_BASE2} 113 #define CONFIG_SYS_MAX_NAND_DEVICE 2 114 #define CONFIG_NAND_FSL_ELBC 115 116 /* 117 * NOR flash configuration 118 */ 119 #define CONFIG_SYS_FLASH_BASE 0xf8000000 120 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 121 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 122 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 123 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 124 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 125 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 126 #define CONFIG_FLASH_CFI_DRIVER 127 #define CONFIG_SYS_FLASH_CFI 128 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 129 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 130 {0xf7f40000, 0xc0000} } 131 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 132 133 /* 134 * Chip select configuration 135 */ 136 /* NOR Flash 0 on CS0 */ 137 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 138 BR_PS_16 | \ 139 BR_V) 140 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 141 OR_GPCM_CSNT | \ 142 OR_GPCM_XACS | \ 143 OR_GPCM_ACS_DIV2 | \ 144 OR_GPCM_SCY_8 | \ 145 OR_GPCM_TRLX | \ 146 OR_GPCM_EHTR | \ 147 OR_GPCM_EAD) 148 149 /* NOR Flash 1 on CS1 */ 150 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 151 BR_PS_16 | \ 152 BR_V) 153 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 154 155 /* NAND flash on CS2 */ 156 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 157 (2<<BR_DECC_SHIFT) | \ 158 BR_PS_8 | \ 159 BR_MS_FCM | \ 160 BR_V) 161 162 /* NAND flash on CS2 */ 163 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 164 OR_FCM_PGS | \ 165 OR_FCM_CSCT | \ 166 OR_FCM_CST | \ 167 OR_FCM_CHT | \ 168 OR_FCM_SCY_1 | \ 169 OR_FCM_TRLX | \ 170 OR_FCM_EHTR) 171 172 /* NAND flash on CS3 */ 173 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 174 (2<<BR_DECC_SHIFT) | \ 175 BR_PS_8 | \ 176 BR_MS_FCM | \ 177 BR_V) 178 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 179 180 /* 181 * Use L1 as initial stack 182 */ 183 #define CONFIG_SYS_INIT_RAM_LOCK 1 184 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 185 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 186 187 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 188 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 189 190 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 191 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 192 193 /* 194 * Serial Port 195 */ 196 #define CONFIG_CONS_INDEX 1 197 #define CONFIG_SYS_NS16550_SERIAL 198 #define CONFIG_SYS_NS16550_REG_SIZE 1 199 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 200 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 201 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 202 #define CONFIG_SYS_BAUDRATE_TABLE \ 203 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 204 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 205 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 206 207 #define CONFIG_FDT_FIXUP_PCI_IRQ 1 208 209 /* 210 * I2C 211 */ 212 #define CONFIG_SYS_I2C 213 #define CONFIG_SYS_I2C_FSL 214 #define CONFIG_SYS_FSL_I2C_SPEED 400000 215 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 216 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 217 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 218 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 219 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 220 221 /* I2C DS7505 temperature sensor */ 222 #define CONFIG_DTT_LM75 223 #define CONFIG_DTT_SENSORS { 0 } 224 #define CONFIG_SYS_I2C_LM75_ADDR 0x48 225 226 /* I2C ADT7461 temperature sensor */ 227 #define CONFIG_SYS_I2C_LM90_ADDR 0x4C 228 229 /* I2C EEPROM - AT24C128B */ 230 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 231 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 232 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 233 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 234 235 /* I2C RTC */ 236 #define CONFIG_RTC_M41T11 1 237 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 238 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 239 240 /* GPIO */ 241 #define CONFIG_PCA953X 242 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 243 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 244 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 245 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 246 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 247 248 /* 249 * GPIO pin definitions, PU = pulled high, PD = pulled low 250 */ 251 /* PCA9557 @ 0x18*/ 252 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 253 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */ 254 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 255 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */ 256 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 257 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */ 258 259 /* PCA9557 @ 0x1e*/ 260 #define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */ 261 #define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */ 262 #define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */ 263 #define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */ 264 #define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */ 265 #define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */ 266 #define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */ 267 268 /* PCA9557 @ 0x1f */ 269 #define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */ 270 #define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */ 271 #define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */ 272 #define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */ 273 #define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */ 274 #define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */ 275 #define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */ 276 #define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */ 277 278 /* 279 * General PCI 280 * Memory space is mapped 1-1, but I/O space must start from 0. 281 */ 282 283 /* controller 1 - PEX8112 or XMC, depending on build option */ 284 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 285 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 286 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 287 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 288 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 289 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 290 291 /* 292 * Networking options 293 */ 294 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 295 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 296 #define CONFIG_TSEC_TBI 297 #define CONFIG_MII 1 /* MII PHY management */ 298 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 299 #define CONFIG_ETHPRIME "eTSEC2" 300 301 /* 302 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 303 * 1000mbps SGMII link 304 */ 305 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 306 TBICR_PHY_RESET \ 307 | TBICR_FULL_DUPLEX \ 308 | TBICR_SPEED1_SET \ 309 ) 310 311 #define CONFIG_TSEC1 1 312 #define CONFIG_TSEC1_NAME "eTSEC1" 313 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 314 #define TSEC1_PHY_ADDR 1 315 #define TSEC1_PHYIDX 0 316 #define CONFIG_HAS_ETH0 317 318 #define CONFIG_TSEC2 1 319 #define CONFIG_TSEC2_NAME "eTSEC2" 320 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 321 #define TSEC2_PHY_ADDR 2 322 #define TSEC2_PHYIDX 0 323 #define CONFIG_HAS_ETH1 324 325 #define CONFIG_TSEC3 1 326 #define CONFIG_TSEC3_NAME "eTSEC3" 327 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 328 #define TSEC3_PHY_ADDR 3 329 #define TSEC3_PHYIDX 0 330 #define CONFIG_HAS_ETH2 331 332 /* 333 * USB 334 */ 335 #define CONFIG_USB_EHCI 336 #define CONFIG_USB_EHCI_FSL 337 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 338 339 /* 340 * Command configuration. 341 */ 342 #define CONFIG_CMD_DTT 343 #define CONFIG_CMD_EEPROM 344 #define CONFIG_CMD_JFFS2 345 #define CONFIG_CMD_NAND 346 #define CONFIG_CMD_PCA953X 347 #define CONFIG_CMD_PCA953X_INFO 348 #define CONFIG_CMD_PCI 349 #define CONFIG_CMD_PCI_ENUM 350 #define CONFIG_CMD_REGINFO 351 352 /* 353 * Miscellaneous configurable options 354 */ 355 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 356 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 357 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 358 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 359 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 360 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 361 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 362 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 363 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 364 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 365 #define CONFIG_PREBOOT /* enable preboot variable */ 366 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 367 368 /* 369 * For booting Linux, the board info and command line data 370 * have to be in the first 16 MB of memory, since this is 371 * the maximum mapped by the Linux kernel during initialization. 372 */ 373 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 374 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 375 376 /* 377 * Environment Configuration 378 */ 379 #define CONFIG_ENV_IS_IN_FLASH 1 380 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 381 #define CONFIG_ENV_SIZE 0x8000 382 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 383 384 /* 385 * Flash memory map: 386 * fff80000 - ffffffff Pri U-Boot (512 KB) 387 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 388 * fff00000 - fff3ffff Pri FDT (256KB) 389 * fef00000 - ffefffff Pri OS image (16MB) 390 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 391 * 392 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 393 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 394 * f7f00000 - f7f3ffff Sec FDT (256KB) 395 * f6f00000 - f7efffff Sec OS image (16MB) 396 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 397 */ 398 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 399 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 400 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 401 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 402 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 403 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 404 405 #define CONFIG_PROG_UBOOT1 \ 406 "$download_cmd $loadaddr $ubootfile; " \ 407 "if test $? -eq 0; then " \ 408 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 409 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 410 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 411 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 412 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 413 "if test $? -ne 0; then " \ 414 "echo PROGRAM FAILED; " \ 415 "else; " \ 416 "echo PROGRAM SUCCEEDED; " \ 417 "fi; " \ 418 "else; " \ 419 "echo DOWNLOAD FAILED; " \ 420 "fi;" 421 422 #define CONFIG_PROG_UBOOT2 \ 423 "$download_cmd $loadaddr $ubootfile; " \ 424 "if test $? -eq 0; then " \ 425 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 426 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 427 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 428 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 429 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 430 "if test $? -ne 0; then " \ 431 "echo PROGRAM FAILED; " \ 432 "else; " \ 433 "echo PROGRAM SUCCEEDED; " \ 434 "fi; " \ 435 "else; " \ 436 "echo DOWNLOAD FAILED; " \ 437 "fi;" 438 439 #define CONFIG_BOOT_OS_NET \ 440 "$download_cmd $osaddr $osfile; " \ 441 "if test $? -eq 0; then " \ 442 "if test -n $fdtaddr; then " \ 443 "$download_cmd $fdtaddr $fdtfile; " \ 444 "if test $? -eq 0; then " \ 445 "bootm $osaddr - $fdtaddr; " \ 446 "else; " \ 447 "echo FDT DOWNLOAD FAILED; " \ 448 "fi; " \ 449 "else; " \ 450 "bootm $osaddr; " \ 451 "fi; " \ 452 "else; " \ 453 "echo OS DOWNLOAD FAILED; " \ 454 "fi;" 455 456 #define CONFIG_PROG_OS1 \ 457 "$download_cmd $osaddr $osfile; " \ 458 "if test $? -eq 0; then " \ 459 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 460 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 461 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 462 "if test $? -ne 0; then " \ 463 "echo OS PROGRAM FAILED; " \ 464 "else; " \ 465 "echo OS PROGRAM SUCCEEDED; " \ 466 "fi; " \ 467 "else; " \ 468 "echo OS DOWNLOAD FAILED; " \ 469 "fi;" 470 471 #define CONFIG_PROG_OS2 \ 472 "$download_cmd $osaddr $osfile; " \ 473 "if test $? -eq 0; then " \ 474 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 475 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 476 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 477 "if test $? -ne 0; then " \ 478 "echo OS PROGRAM FAILED; " \ 479 "else; " \ 480 "echo OS PROGRAM SUCCEEDED; " \ 481 "fi; " \ 482 "else; " \ 483 "echo OS DOWNLOAD FAILED; " \ 484 "fi;" 485 486 #define CONFIG_PROG_FDT1 \ 487 "$download_cmd $fdtaddr $fdtfile; " \ 488 "if test $? -eq 0; then " \ 489 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 490 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 491 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 492 "if test $? -ne 0; then " \ 493 "echo FDT PROGRAM FAILED; " \ 494 "else; " \ 495 "echo FDT PROGRAM SUCCEEDED; " \ 496 "fi; " \ 497 "else; " \ 498 "echo FDT DOWNLOAD FAILED; " \ 499 "fi;" 500 501 #define CONFIG_PROG_FDT2 \ 502 "$download_cmd $fdtaddr $fdtfile; " \ 503 "if test $? -eq 0; then " \ 504 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 505 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 506 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 507 "if test $? -ne 0; then " \ 508 "echo FDT PROGRAM FAILED; " \ 509 "else; " \ 510 "echo FDT PROGRAM SUCCEEDED; " \ 511 "fi; " \ 512 "else; " \ 513 "echo FDT DOWNLOAD FAILED; " \ 514 "fi;" 515 516 #define CONFIG_EXTRA_ENV_SETTINGS \ 517 "autoload=yes\0" \ 518 "download_cmd=tftp\0" \ 519 "console_args=console=ttyS0,115200\0" \ 520 "root_args=root=/dev/nfs rw\0" \ 521 "misc_args=ip=on\0" \ 522 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 523 "bootfile=/home/user/file\0" \ 524 "osfile=/home/user/board.uImage\0" \ 525 "fdtfile=/home/user/board.dtb\0" \ 526 "ubootfile=/home/user/u-boot.bin\0" \ 527 "fdtaddr=0x1e00000\0" \ 528 "osaddr=0x1000000\0" \ 529 "loadaddr=0x1000000\0" \ 530 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 531 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 532 "prog_os1="CONFIG_PROG_OS1"\0" \ 533 "prog_os2="CONFIG_PROG_OS2"\0" \ 534 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 535 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 536 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 537 "bootcmd_flash1=run set_bootargs; " \ 538 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 539 "bootcmd_flash2=run set_bootargs; " \ 540 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 541 "bootcmd=run bootcmd_flash1\0" 542 #endif /* __CONFIG_H */ 543