1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2008 Extreme Engineering Solutions, Inc. 4 * Copyright 2007-2008 Freescale Semiconductor, Inc. 5 */ 6 7 /* 8 * xpedite537x board configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* 14 * High Level Configuration Options 15 */ 16 #define CONFIG_SYS_BOARD_NAME "XPedite5370" 17 #define CONFIG_SYS_FORM_3U_VPX 1 18 19 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 20 #define CONFIG_PCIE1 1 /* PCIE controller 1 */ 21 #define CONFIG_PCIE2 1 /* PCIE controller 2 */ 22 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 23 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 24 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 25 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 26 27 /* 28 * Multicore config 29 */ 30 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 31 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 32 33 /* 34 * DDR config 35 */ 36 #undef CONFIG_FSL_DDR_INTERACTIVE 37 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 38 #define CONFIG_DDR_SPD 39 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 40 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 41 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 42 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 43 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 44 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 45 #define CONFIG_DDR_ECC 46 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 47 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 48 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 49 #define CONFIG_VERY_BIG_RAM 50 51 #ifndef __ASSEMBLY__ 52 extern unsigned long get_board_sys_clk(unsigned long dummy); 53 extern unsigned long get_board_ddr_clk(unsigned long dummy); 54 #endif 55 56 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 57 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 58 59 /* 60 * These can be toggled for performance analysis, otherwise use default. 61 */ 62 #define CONFIG_L2_CACHE /* toggle L2 cache */ 63 #define CONFIG_BTB /* toggle branch predition */ 64 #define CONFIG_ENABLE_36BIT_PHYS 1 65 66 #define CONFIG_SYS_CCSRBAR 0xef000000 67 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 68 69 /* 70 * Diagnostics 71 */ 72 #define CONFIG_SYS_MEMTEST_START 0x10000000 73 #define CONFIG_SYS_MEMTEST_END 0x20000000 74 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 75 CONFIG_SYS_POST_I2C) 76 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ 77 #define I2C_ADDR_IGNORE_LIST {0x50} 78 79 /* 80 * Memory map 81 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 82 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 83 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 84 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 85 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 86 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 87 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 88 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 89 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 90 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 91 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 92 */ 93 94 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 95 96 /* 97 * NAND flash configuration 98 */ 99 #define CONFIG_SYS_NAND_BASE 0xef800000 100 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 101 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 102 CONFIG_SYS_NAND_BASE2} 103 #define CONFIG_SYS_MAX_NAND_DEVICE 2 104 #define CONFIG_NAND_FSL_ELBC 105 106 /* 107 * NOR flash configuration 108 */ 109 #define CONFIG_SYS_FLASH_BASE 0xf8000000 110 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 111 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 112 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 113 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 114 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 115 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 116 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 117 {0xf7f40000, 0xc0000} } 118 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 119 120 /* 121 * Chip select configuration 122 */ 123 /* NOR Flash 0 on CS0 */ 124 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 125 BR_PS_16 | \ 126 BR_V) 127 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 128 OR_GPCM_CSNT | \ 129 OR_GPCM_XACS | \ 130 OR_GPCM_ACS_DIV2 | \ 131 OR_GPCM_SCY_8 | \ 132 OR_GPCM_TRLX | \ 133 OR_GPCM_EHTR | \ 134 OR_GPCM_EAD) 135 136 /* NOR Flash 1 on CS1 */ 137 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 138 BR_PS_16 | \ 139 BR_V) 140 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 141 142 /* NAND flash on CS2 */ 143 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 144 (2<<BR_DECC_SHIFT) | \ 145 BR_PS_8 | \ 146 BR_MS_FCM | \ 147 BR_V) 148 149 /* NAND flash on CS2 */ 150 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 151 OR_FCM_PGS | \ 152 OR_FCM_CSCT | \ 153 OR_FCM_CST | \ 154 OR_FCM_CHT | \ 155 OR_FCM_SCY_1 | \ 156 OR_FCM_TRLX | \ 157 OR_FCM_EHTR) 158 159 /* NAND flash on CS3 */ 160 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 161 (2<<BR_DECC_SHIFT) | \ 162 BR_PS_8 | \ 163 BR_MS_FCM | \ 164 BR_V) 165 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 166 167 /* 168 * Use L1 as initial stack 169 */ 170 #define CONFIG_SYS_INIT_RAM_LOCK 1 171 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 172 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 173 174 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 175 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 176 177 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 178 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 179 180 /* 181 * Serial Port 182 */ 183 #define CONFIG_SYS_NS16550_SERIAL 184 #define CONFIG_SYS_NS16550_REG_SIZE 1 185 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 186 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 187 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 188 #define CONFIG_SYS_BAUDRATE_TABLE \ 189 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 190 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 191 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 192 193 /* 194 * I2C 195 */ 196 #define CONFIG_SYS_I2C 197 #define CONFIG_SYS_I2C_FSL 198 #define CONFIG_SYS_FSL_I2C_SPEED 400000 199 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 200 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 201 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 202 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 203 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 204 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 205 206 /* PEX8518 slave I2C interface */ 207 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 208 209 /* I2C DS1631 temperature sensor */ 210 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 211 212 /* I2C EEPROM - AT24C128B */ 213 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 214 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 215 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 216 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 217 218 /* I2C RTC */ 219 #define CONFIG_RTC_M41T11 1 220 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 221 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 222 223 /* GPIO */ 224 #define CONFIG_PCA953X 225 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 226 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 227 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 228 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 229 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 230 231 /* 232 * PU = pulled high, PD = pulled low 233 * I = input, O = output, IO = input/output 234 */ 235 /* PCA9557 @ 0x18*/ 236 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 237 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 238 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 239 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 240 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 241 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 242 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ 243 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ 244 245 /* PCA9557 @ 0x1c*/ 246 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 247 #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ 248 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 249 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 250 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 251 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 252 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 253 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 254 255 /* PCA9557 @ 0x1e*/ 256 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 257 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 258 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 259 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 260 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 261 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ 262 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ 263 264 /* PCA9557 @ 0x1f */ 265 #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ 266 #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ 267 #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ 268 #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ 269 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ 270 271 /* 272 * General PCI 273 * Memory space is mapped 1-1, but I/O space must start from 0. 274 */ 275 /* PCIE1 - VPX P1 */ 276 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 277 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 278 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 279 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 280 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 281 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 282 283 /* PCIE2 - PEX8518 */ 284 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 285 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 286 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 287 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 288 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 289 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 290 291 /* 292 * Networking options 293 */ 294 #define CONFIG_TSEC_TBI 295 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 296 #define CONFIG_ETHPRIME "eTSEC2" 297 298 /* 299 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 300 * 1000mbps SGMII link 301 */ 302 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 303 TBICR_PHY_RESET \ 304 | TBICR_FULL_DUPLEX \ 305 | TBICR_SPEED1_SET \ 306 ) 307 308 #define CONFIG_TSEC1 1 309 #define CONFIG_TSEC1_NAME "eTSEC1" 310 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 311 #define TSEC1_PHY_ADDR 1 312 #define TSEC1_PHYIDX 0 313 #define CONFIG_HAS_ETH0 314 315 #define CONFIG_TSEC2 1 316 #define CONFIG_TSEC2_NAME "eTSEC2" 317 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 318 #define TSEC2_PHY_ADDR 2 319 #define TSEC2_PHYIDX 0 320 #define CONFIG_HAS_ETH1 321 322 /* 323 * Miscellaneous configurable options 324 */ 325 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 326 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 327 #define CONFIG_PREBOOT /* enable preboot variable */ 328 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 329 330 /* 331 * For booting Linux, the board info and command line data 332 * have to be in the first 16 MB of memory, since this is 333 * the maximum mapped by the Linux kernel during initialization. 334 */ 335 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 336 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 337 338 /* 339 * Environment Configuration 340 */ 341 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 342 #define CONFIG_ENV_SIZE 0x8000 343 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 344 345 /* 346 * Flash memory map: 347 * fff80000 - ffffffff Pri U-Boot (512 KB) 348 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 349 * fff00000 - fff3ffff Pri FDT (256KB) 350 * fef00000 - ffefffff Pri OS image (16MB) 351 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 352 * 353 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 354 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 355 * f7f00000 - f7f3ffff Sec FDT (256KB) 356 * f6f00000 - f7efffff Sec OS image (16MB) 357 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 358 */ 359 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 360 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 361 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 362 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 363 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 364 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 365 366 #define CONFIG_PROG_UBOOT1 \ 367 "$download_cmd $loadaddr $ubootfile; " \ 368 "if test $? -eq 0; then " \ 369 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 370 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 371 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 372 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 373 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 374 "if test $? -ne 0; then " \ 375 "echo PROGRAM FAILED; " \ 376 "else; " \ 377 "echo PROGRAM SUCCEEDED; " \ 378 "fi; " \ 379 "else; " \ 380 "echo DOWNLOAD FAILED; " \ 381 "fi;" 382 383 #define CONFIG_PROG_UBOOT2 \ 384 "$download_cmd $loadaddr $ubootfile; " \ 385 "if test $? -eq 0; then " \ 386 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 387 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 388 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 389 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 390 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 391 "if test $? -ne 0; then " \ 392 "echo PROGRAM FAILED; " \ 393 "else; " \ 394 "echo PROGRAM SUCCEEDED; " \ 395 "fi; " \ 396 "else; " \ 397 "echo DOWNLOAD FAILED; " \ 398 "fi;" 399 400 #define CONFIG_BOOT_OS_NET \ 401 "$download_cmd $osaddr $osfile; " \ 402 "if test $? -eq 0; then " \ 403 "if test -n $fdtaddr; then " \ 404 "$download_cmd $fdtaddr $fdtfile; " \ 405 "if test $? -eq 0; then " \ 406 "bootm $osaddr - $fdtaddr; " \ 407 "else; " \ 408 "echo FDT DOWNLOAD FAILED; " \ 409 "fi; " \ 410 "else; " \ 411 "bootm $osaddr; " \ 412 "fi; " \ 413 "else; " \ 414 "echo OS DOWNLOAD FAILED; " \ 415 "fi;" 416 417 #define CONFIG_PROG_OS1 \ 418 "$download_cmd $osaddr $osfile; " \ 419 "if test $? -eq 0; then " \ 420 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 421 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 422 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 423 "if test $? -ne 0; then " \ 424 "echo OS PROGRAM FAILED; " \ 425 "else; " \ 426 "echo OS PROGRAM SUCCEEDED; " \ 427 "fi; " \ 428 "else; " \ 429 "echo OS DOWNLOAD FAILED; " \ 430 "fi;" 431 432 #define CONFIG_PROG_OS2 \ 433 "$download_cmd $osaddr $osfile; " \ 434 "if test $? -eq 0; then " \ 435 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 436 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 437 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 438 "if test $? -ne 0; then " \ 439 "echo OS PROGRAM FAILED; " \ 440 "else; " \ 441 "echo OS PROGRAM SUCCEEDED; " \ 442 "fi; " \ 443 "else; " \ 444 "echo OS DOWNLOAD FAILED; " \ 445 "fi;" 446 447 #define CONFIG_PROG_FDT1 \ 448 "$download_cmd $fdtaddr $fdtfile; " \ 449 "if test $? -eq 0; then " \ 450 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 451 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 452 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 453 "if test $? -ne 0; then " \ 454 "echo FDT PROGRAM FAILED; " \ 455 "else; " \ 456 "echo FDT PROGRAM SUCCEEDED; " \ 457 "fi; " \ 458 "else; " \ 459 "echo FDT DOWNLOAD FAILED; " \ 460 "fi;" 461 462 #define CONFIG_PROG_FDT2 \ 463 "$download_cmd $fdtaddr $fdtfile; " \ 464 "if test $? -eq 0; then " \ 465 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 466 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 467 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 468 "if test $? -ne 0; then " \ 469 "echo FDT PROGRAM FAILED; " \ 470 "else; " \ 471 "echo FDT PROGRAM SUCCEEDED; " \ 472 "fi; " \ 473 "else; " \ 474 "echo FDT DOWNLOAD FAILED; " \ 475 "fi;" 476 477 #define CONFIG_EXTRA_ENV_SETTINGS \ 478 "autoload=yes\0" \ 479 "download_cmd=tftp\0" \ 480 "console_args=console=ttyS0,115200\0" \ 481 "root_args=root=/dev/nfs rw\0" \ 482 "misc_args=ip=on\0" \ 483 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 484 "bootfile=/home/user/file\0" \ 485 "osfile=/home/user/board.uImage\0" \ 486 "fdtfile=/home/user/board.dtb\0" \ 487 "ubootfile=/home/user/u-boot.bin\0" \ 488 "fdtaddr=0x1e00000\0" \ 489 "osaddr=0x1000000\0" \ 490 "loadaddr=0x1000000\0" \ 491 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 492 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 493 "prog_os1="CONFIG_PROG_OS1"\0" \ 494 "prog_os2="CONFIG_PROG_OS2"\0" \ 495 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 496 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 497 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 498 "bootcmd_flash1=run set_bootargs; " \ 499 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 500 "bootcmd_flash2=run set_bootargs; " \ 501 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 502 "bootcmd=run bootcmd_flash1\0" 503 #endif /* __CONFIG_H */ 504