1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite537x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_SYS_BOARD_NAME "XPedite5370" 18 #define CONFIG_SYS_FORM_3U_VPX 1 19 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 20 21 #ifndef CONFIG_SYS_TEXT_BASE 22 #define CONFIG_SYS_TEXT_BASE 0xfff80000 23 #endif 24 25 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 26 #define CONFIG_PCIE1 1 /* PCIE controller 1 */ 27 #define CONFIG_PCIE2 1 /* PCIE controller 2 */ 28 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 29 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 30 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 31 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 32 #define CONFIG_FSL_ELBC 1 33 34 /* 35 * Multicore config 36 */ 37 #define CONFIG_MP 38 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 39 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 40 41 /* 42 * DDR config 43 */ 44 #undef CONFIG_FSL_DDR_INTERACTIVE 45 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 46 #define CONFIG_DDR_SPD 47 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 48 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 49 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 50 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 51 #define CONFIG_NUM_DDR_CONTROLLERS 2 52 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 53 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 54 #define CONFIG_DDR_ECC 55 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 56 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 57 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 58 #define CONFIG_VERY_BIG_RAM 59 60 #ifndef __ASSEMBLY__ 61 extern unsigned long get_board_sys_clk(unsigned long dummy); 62 extern unsigned long get_board_ddr_clk(unsigned long dummy); 63 #endif 64 65 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 66 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 67 68 /* 69 * These can be toggled for performance analysis, otherwise use default. 70 */ 71 #define CONFIG_L2_CACHE /* toggle L2 cache */ 72 #define CONFIG_BTB /* toggle branch predition */ 73 #define CONFIG_ENABLE_36BIT_PHYS 1 74 75 #define CONFIG_SYS_CCSRBAR 0xef000000 76 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 77 78 /* 79 * Diagnostics 80 */ 81 #define CONFIG_SYS_ALT_MEMTEST 82 #define CONFIG_SYS_MEMTEST_START 0x10000000 83 #define CONFIG_SYS_MEMTEST_END 0x20000000 84 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 85 CONFIG_SYS_POST_I2C) 86 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ 87 CONFIG_SYS_I2C_DS4510_ADDR, \ 88 CONFIG_SYS_I2C_EEPROM_ADDR, \ 89 CONFIG_SYS_I2C_LM90_ADDR, \ 90 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 91 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 92 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 93 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 94 CONFIG_SYS_I2C_PEX8518_ADDR, \ 95 CONFIG_SYS_I2C_RTC_ADDR} 96 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ 97 #define I2C_ADDR_IGNORE_LIST {0x50} 98 99 /* 100 * Memory map 101 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 102 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 103 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 104 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 105 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 106 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 107 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 108 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 109 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 110 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 111 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 112 */ 113 114 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 115 116 /* 117 * NAND flash configuration 118 */ 119 #define CONFIG_SYS_NAND_BASE 0xef800000 120 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 121 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 122 CONFIG_SYS_NAND_BASE2} 123 #define CONFIG_SYS_MAX_NAND_DEVICE 2 124 #define CONFIG_NAND_FSL_ELBC 125 126 /* 127 * NOR flash configuration 128 */ 129 #define CONFIG_SYS_FLASH_BASE 0xf8000000 130 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 131 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 132 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 133 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 134 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 135 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 136 #define CONFIG_FLASH_CFI_DRIVER 137 #define CONFIG_SYS_FLASH_CFI 138 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 139 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 140 {0xf7f40000, 0xc0000} } 141 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 142 143 /* 144 * Chip select configuration 145 */ 146 /* NOR Flash 0 on CS0 */ 147 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 148 BR_PS_16 | \ 149 BR_V) 150 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 151 OR_GPCM_CSNT | \ 152 OR_GPCM_XACS | \ 153 OR_GPCM_ACS_DIV2 | \ 154 OR_GPCM_SCY_8 | \ 155 OR_GPCM_TRLX | \ 156 OR_GPCM_EHTR | \ 157 OR_GPCM_EAD) 158 159 /* NOR Flash 1 on CS1 */ 160 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 161 BR_PS_16 | \ 162 BR_V) 163 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 164 165 /* NAND flash on CS2 */ 166 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 167 (2<<BR_DECC_SHIFT) | \ 168 BR_PS_8 | \ 169 BR_MS_FCM | \ 170 BR_V) 171 172 /* NAND flash on CS2 */ 173 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 174 OR_FCM_PGS | \ 175 OR_FCM_CSCT | \ 176 OR_FCM_CST | \ 177 OR_FCM_CHT | \ 178 OR_FCM_SCY_1 | \ 179 OR_FCM_TRLX | \ 180 OR_FCM_EHTR) 181 182 /* NAND flash on CS3 */ 183 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 184 (2<<BR_DECC_SHIFT) | \ 185 BR_PS_8 | \ 186 BR_MS_FCM | \ 187 BR_V) 188 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 189 190 /* 191 * Use L1 as initial stack 192 */ 193 #define CONFIG_SYS_INIT_RAM_LOCK 1 194 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 195 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 196 197 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 198 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 199 200 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 201 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 202 203 /* 204 * Serial Port 205 */ 206 #define CONFIG_CONS_INDEX 1 207 #define CONFIG_SYS_NS16550_SERIAL 208 #define CONFIG_SYS_NS16550_REG_SIZE 1 209 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 210 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 211 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 212 #define CONFIG_SYS_BAUDRATE_TABLE \ 213 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 214 #define CONFIG_BAUDRATE 115200 215 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 216 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 217 218 /* 219 * I2C 220 */ 221 #define CONFIG_SYS_I2C 222 #define CONFIG_SYS_I2C_FSL 223 #define CONFIG_SYS_FSL_I2C_SPEED 400000 224 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 225 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 226 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 227 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 228 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 229 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 230 231 /* PEX8518 slave I2C interface */ 232 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 233 234 /* I2C DS1631 temperature sensor */ 235 #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 236 #define CONFIG_DTT_DS1621 237 #define CONFIG_DTT_SENSORS { 0 } 238 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 239 240 /* I2C EEPROM - AT24C128B */ 241 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 242 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 243 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 244 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 245 246 /* I2C RTC */ 247 #define CONFIG_RTC_M41T11 1 248 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 249 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 250 251 /* GPIO/EEPROM/SRAM */ 252 #define CONFIG_DS4510 253 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 254 255 /* GPIO */ 256 #define CONFIG_PCA953X 257 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 258 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 259 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 260 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 261 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 262 263 /* 264 * PU = pulled high, PD = pulled low 265 * I = input, O = output, IO = input/output 266 */ 267 /* PCA9557 @ 0x18*/ 268 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 269 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 270 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 271 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 272 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 273 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 274 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ 275 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ 276 277 /* PCA9557 @ 0x1c*/ 278 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 279 #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ 280 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 281 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 282 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 283 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 284 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 285 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 286 287 /* PCA9557 @ 0x1e*/ 288 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 289 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 290 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 291 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 292 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 293 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ 294 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ 295 296 /* PCA9557 @ 0x1f */ 297 #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ 298 #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ 299 #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ 300 #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ 301 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ 302 303 /* 304 * General PCI 305 * Memory space is mapped 1-1, but I/O space must start from 0. 306 */ 307 /* PCIE1 - VPX P1 */ 308 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 309 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 310 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 311 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 312 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 313 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 314 315 /* PCIE2 - PEX8518 */ 316 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 317 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 318 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 319 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 320 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 321 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 322 323 /* 324 * Networking options 325 */ 326 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 327 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 328 #define CONFIG_TSEC_TBI 329 #define CONFIG_MII 1 /* MII PHY management */ 330 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 331 #define CONFIG_ETHPRIME "eTSEC2" 332 333 /* 334 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 335 * 1000mbps SGMII link 336 */ 337 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 338 TBICR_PHY_RESET \ 339 | TBICR_FULL_DUPLEX \ 340 | TBICR_SPEED1_SET \ 341 ) 342 343 #define CONFIG_TSEC1 1 344 #define CONFIG_TSEC1_NAME "eTSEC1" 345 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 346 #define TSEC1_PHY_ADDR 1 347 #define TSEC1_PHYIDX 0 348 #define CONFIG_HAS_ETH0 349 350 #define CONFIG_TSEC2 1 351 #define CONFIG_TSEC2_NAME "eTSEC2" 352 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 353 #define TSEC2_PHY_ADDR 2 354 #define TSEC2_PHYIDX 0 355 #define CONFIG_HAS_ETH1 356 357 /* 358 * Command configuration. 359 */ 360 #define CONFIG_CMD_DATE 361 #define CONFIG_CMD_DS4510 362 #define CONFIG_CMD_DS4510_INFO 363 #define CONFIG_CMD_DTT 364 #define CONFIG_CMD_EEPROM 365 #define CONFIG_CMD_JFFS2 366 #define CONFIG_CMD_NAND 367 #define CONFIG_CMD_PCA953X 368 #define CONFIG_CMD_PCA953X_INFO 369 #define CONFIG_CMD_PCI 370 #define CONFIG_CMD_PCI_ENUM 371 #define CONFIG_CMD_REGINFO 372 373 /* 374 * Miscellaneous configurable options 375 */ 376 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 377 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 378 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 379 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 380 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 381 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 382 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 383 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 384 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 385 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 386 #define CONFIG_PREBOOT /* enable preboot variable */ 387 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 388 389 /* 390 * For booting Linux, the board info and command line data 391 * have to be in the first 16 MB of memory, since this is 392 * the maximum mapped by the Linux kernel during initialization. 393 */ 394 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 395 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 396 397 /* 398 * Environment Configuration 399 */ 400 #define CONFIG_ENV_IS_IN_FLASH 1 401 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 402 #define CONFIG_ENV_SIZE 0x8000 403 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 404 405 /* 406 * Flash memory map: 407 * fff80000 - ffffffff Pri U-Boot (512 KB) 408 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 409 * fff00000 - fff3ffff Pri FDT (256KB) 410 * fef00000 - ffefffff Pri OS image (16MB) 411 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 412 * 413 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 414 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 415 * f7f00000 - f7f3ffff Sec FDT (256KB) 416 * f6f00000 - f7efffff Sec OS image (16MB) 417 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 418 */ 419 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 420 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 421 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 422 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 423 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 424 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 425 426 #define CONFIG_PROG_UBOOT1 \ 427 "$download_cmd $loadaddr $ubootfile; " \ 428 "if test $? -eq 0; then " \ 429 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 430 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 431 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 432 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 433 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 434 "if test $? -ne 0; then " \ 435 "echo PROGRAM FAILED; " \ 436 "else; " \ 437 "echo PROGRAM SUCCEEDED; " \ 438 "fi; " \ 439 "else; " \ 440 "echo DOWNLOAD FAILED; " \ 441 "fi;" 442 443 #define CONFIG_PROG_UBOOT2 \ 444 "$download_cmd $loadaddr $ubootfile; " \ 445 "if test $? -eq 0; then " \ 446 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 447 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 448 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 449 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 450 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 451 "if test $? -ne 0; then " \ 452 "echo PROGRAM FAILED; " \ 453 "else; " \ 454 "echo PROGRAM SUCCEEDED; " \ 455 "fi; " \ 456 "else; " \ 457 "echo DOWNLOAD FAILED; " \ 458 "fi;" 459 460 #define CONFIG_BOOT_OS_NET \ 461 "$download_cmd $osaddr $osfile; " \ 462 "if test $? -eq 0; then " \ 463 "if test -n $fdtaddr; then " \ 464 "$download_cmd $fdtaddr $fdtfile; " \ 465 "if test $? -eq 0; then " \ 466 "bootm $osaddr - $fdtaddr; " \ 467 "else; " \ 468 "echo FDT DOWNLOAD FAILED; " \ 469 "fi; " \ 470 "else; " \ 471 "bootm $osaddr; " \ 472 "fi; " \ 473 "else; " \ 474 "echo OS DOWNLOAD FAILED; " \ 475 "fi;" 476 477 #define CONFIG_PROG_OS1 \ 478 "$download_cmd $osaddr $osfile; " \ 479 "if test $? -eq 0; then " \ 480 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 481 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 482 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 483 "if test $? -ne 0; then " \ 484 "echo OS PROGRAM FAILED; " \ 485 "else; " \ 486 "echo OS PROGRAM SUCCEEDED; " \ 487 "fi; " \ 488 "else; " \ 489 "echo OS DOWNLOAD FAILED; " \ 490 "fi;" 491 492 #define CONFIG_PROG_OS2 \ 493 "$download_cmd $osaddr $osfile; " \ 494 "if test $? -eq 0; then " \ 495 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 496 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 497 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 498 "if test $? -ne 0; then " \ 499 "echo OS PROGRAM FAILED; " \ 500 "else; " \ 501 "echo OS PROGRAM SUCCEEDED; " \ 502 "fi; " \ 503 "else; " \ 504 "echo OS DOWNLOAD FAILED; " \ 505 "fi;" 506 507 #define CONFIG_PROG_FDT1 \ 508 "$download_cmd $fdtaddr $fdtfile; " \ 509 "if test $? -eq 0; then " \ 510 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 511 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 512 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 513 "if test $? -ne 0; then " \ 514 "echo FDT PROGRAM FAILED; " \ 515 "else; " \ 516 "echo FDT PROGRAM SUCCEEDED; " \ 517 "fi; " \ 518 "else; " \ 519 "echo FDT DOWNLOAD FAILED; " \ 520 "fi;" 521 522 #define CONFIG_PROG_FDT2 \ 523 "$download_cmd $fdtaddr $fdtfile; " \ 524 "if test $? -eq 0; then " \ 525 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 526 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 527 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 528 "if test $? -ne 0; then " \ 529 "echo FDT PROGRAM FAILED; " \ 530 "else; " \ 531 "echo FDT PROGRAM SUCCEEDED; " \ 532 "fi; " \ 533 "else; " \ 534 "echo FDT DOWNLOAD FAILED; " \ 535 "fi;" 536 537 #define CONFIG_EXTRA_ENV_SETTINGS \ 538 "autoload=yes\0" \ 539 "download_cmd=tftp\0" \ 540 "console_args=console=ttyS0,115200\0" \ 541 "root_args=root=/dev/nfs rw\0" \ 542 "misc_args=ip=on\0" \ 543 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 544 "bootfile=/home/user/file\0" \ 545 "osfile=/home/user/board.uImage\0" \ 546 "fdtfile=/home/user/board.dtb\0" \ 547 "ubootfile=/home/user/u-boot.bin\0" \ 548 "fdtaddr=0x1e00000\0" \ 549 "osaddr=0x1000000\0" \ 550 "loadaddr=0x1000000\0" \ 551 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 552 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 553 "prog_os1="CONFIG_PROG_OS1"\0" \ 554 "prog_os2="CONFIG_PROG_OS2"\0" \ 555 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 556 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 557 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 558 "bootcmd_flash1=run set_bootargs; " \ 559 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 560 "bootcmd_flash2=run set_bootargs; " \ 561 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 562 "bootcmd=run bootcmd_flash1\0" 563 #endif /* __CONFIG_H */ 564