1 /*
2  * Copyright 2008 Extreme Engineering Solutions, Inc.
3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 /*
9  * xpedite537x board configuration file
10  */
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /*
15  * High Level Configuration Options
16  */
17 #define CONFIG_SYS_BOARD_NAME	"XPedite5370"
18 #define CONFIG_SYS_FORM_3U_VPX	1
19 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
20 
21 #ifndef CONFIG_SYS_TEXT_BASE
22 #define CONFIG_SYS_TEXT_BASE	0xfff80000
23 #endif
24 
25 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
26 #define CONFIG_PCIE1		1	/* PCIE controller 1 */
27 #define CONFIG_PCIE2		1	/* PCIE controller 2 */
28 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
29 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
30 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
31 #define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
32 
33 /*
34  * Multicore config
35  */
36 #define CONFIG_MP
37 #define CONFIG_BPTR_VIRT_ADDR	0xee000000	/* virt boot page address */
38 #define CONFIG_MPC8xxx_DISABLE_BPTR		/* Don't leave BPTR enabled */
39 
40 /*
41  * DDR config
42  */
43 #undef CONFIG_FSL_DDR_INTERACTIVE
44 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
45 #define CONFIG_DDR_SPD
46 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
47 #define SPD_EEPROM_ADDRESS1		0x54	/* Both channels use the */
48 #define SPD_EEPROM_ADDRESS2		0x54	/* same SPD data         */
49 #define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
50 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
51 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
52 #define CONFIG_DDR_ECC
53 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
54 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000 /* DDR is system memory*/
55 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
56 #define CONFIG_VERY_BIG_RAM
57 
58 #ifndef __ASSEMBLY__
59 extern unsigned long get_board_sys_clk(unsigned long dummy);
60 extern unsigned long get_board_ddr_clk(unsigned long dummy);
61 #endif
62 
63 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
64 #define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */
65 
66 /*
67  * These can be toggled for performance analysis, otherwise use default.
68  */
69 #define CONFIG_L2_CACHE			/* toggle L2 cache */
70 #define CONFIG_BTB			/* toggle branch predition */
71 #define CONFIG_ENABLE_36BIT_PHYS	1
72 
73 #define CONFIG_SYS_CCSRBAR		0xef000000
74 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
75 
76 /*
77  * Diagnostics
78  */
79 #define CONFIG_SYS_ALT_MEMTEST
80 #define CONFIG_SYS_MEMTEST_START	0x10000000
81 #define CONFIG_SYS_MEMTEST_END		0x20000000
82 #define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
83 					 CONFIG_SYS_POST_I2C)
84 #define I2C_ADDR_LIST			{CONFIG_SYS_I2C_DS1621_ADDR,	\
85 					 CONFIG_SYS_I2C_DS4510_ADDR,	\
86 					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
87 					 CONFIG_SYS_I2C_LM90_ADDR,	\
88 					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
89 					 CONFIG_SYS_I2C_PCA953X_ADDR1,	\
90 					 CONFIG_SYS_I2C_PCA953X_ADDR2,	\
91 					 CONFIG_SYS_I2C_PCA953X_ADDR3,	\
92 					 CONFIG_SYS_I2C_PEX8518_ADDR,	\
93 					 CONFIG_SYS_I2C_RTC_ADDR}
94 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
95 #define I2C_ADDR_IGNORE_LIST		{0x50}
96 
97 /*
98  * Memory map
99  * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
100  * 0x8000_0000	0xbfff_ffff	PCIe1 Mem		1G non-cacheable
101  * 0xc000_0000	0xcfff_ffff	PCIe2 Mem		256M non-cacheable
102  * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
103  * 0xe800_0000	0xe87f_ffff	PCIe1 IO		8M non-cacheable
104  * 0xe880_0000	0xe8ff_ffff	PCIe2 IO		8M non-cacheable
105  * 0xee00_0000	0xee00_ffff	Boot page translation	4K non-cacheable
106  * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
107  * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
108  * 0xf000_0000	0xf7ff_ffff	NOR Flash 2		128M non-cacheable
109  * 0xf800_0000	0xffff_ffff	NOR Flash 1		128M non-cacheable
110  */
111 
112 #define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)
113 
114 /*
115  * NAND flash configuration
116  */
117 #define CONFIG_SYS_NAND_BASE		0xef800000
118 #define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
119 #define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE, \
120 					 CONFIG_SYS_NAND_BASE2}
121 #define CONFIG_SYS_MAX_NAND_DEVICE	2
122 #define CONFIG_NAND_FSL_ELBC
123 
124 /*
125  * NOR flash configuration
126  */
127 #define CONFIG_SYS_FLASH_BASE		0xf8000000
128 #define CONFIG_SYS_FLASH_BASE2		0xf0000000
129 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
130 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
131 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
132 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
133 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
134 #define CONFIG_FLASH_CFI_DRIVER
135 #define CONFIG_SYS_FLASH_CFI
136 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
137 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
138 						  {0xf7f40000, 0xc0000} }
139 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
140 
141 /*
142  * Chip select configuration
143  */
144 /* NOR Flash 0 on CS0 */
145 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
146 				 BR_PS_16		| \
147 				 BR_V)
148 #define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		| \
149 				 OR_GPCM_CSNT		| \
150 				 OR_GPCM_XACS		| \
151 				 OR_GPCM_ACS_DIV2	| \
152 				 OR_GPCM_SCY_8		| \
153 				 OR_GPCM_TRLX		| \
154 				 OR_GPCM_EHTR		| \
155 				 OR_GPCM_EAD)
156 
157 /* NOR Flash 1 on CS1 */
158 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
159 				 BR_PS_16		| \
160 				 BR_V)
161 #define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
162 
163 /* NAND flash on CS2 */
164 #define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
165 				 (2<<BR_DECC_SHIFT)	| \
166 				 BR_PS_8		| \
167 				 BR_MS_FCM		| \
168 				 BR_V)
169 
170 /* NAND flash on CS2 */
171 #define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB	| \
172 				 OR_FCM_PGS	| \
173 				 OR_FCM_CSCT	| \
174 				 OR_FCM_CST	| \
175 				 OR_FCM_CHT	| \
176 				 OR_FCM_SCY_1	| \
177 				 OR_FCM_TRLX	| \
178 				 OR_FCM_EHTR)
179 
180 /* NAND flash on CS3 */
181 #define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
182 				 (2<<BR_DECC_SHIFT)	| \
183 				 BR_PS_8		| \
184 				 BR_MS_FCM		| \
185 				 BR_V)
186 #define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
187 
188 /*
189  * Use L1 as initial stack
190  */
191 #define CONFIG_SYS_INIT_RAM_LOCK	1
192 #define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
193 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
194 
195 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
196 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
197 
198 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
199 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
200 
201 /*
202  * Serial Port
203  */
204 #define CONFIG_CONS_INDEX		1
205 #define CONFIG_SYS_NS16550_SERIAL
206 #define CONFIG_SYS_NS16550_REG_SIZE	1
207 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
208 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
209 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
210 #define CONFIG_SYS_BAUDRATE_TABLE	\
211 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
212 #define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
213 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
214 
215 /*
216  * I2C
217  */
218 #define CONFIG_SYS_I2C
219 #define CONFIG_SYS_I2C_FSL
220 #define CONFIG_SYS_FSL_I2C_SPEED	400000
221 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
222 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
223 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
224 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
225 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
226 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
227 
228 /* PEX8518 slave I2C interface */
229 #define CONFIG_SYS_I2C_PEX8518_ADDR	0x70
230 
231 /* I2C DS1631 temperature sensor */
232 #define CONFIG_SYS_I2C_DS1621_ADDR	0x48
233 #define CONFIG_DTT_DS1621
234 #define CONFIG_DTT_SENSORS		{ 0 }
235 #define CONFIG_SYS_I2C_LM90_ADDR	0x4c
236 
237 /* I2C EEPROM - AT24C128B */
238 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
239 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
240 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
241 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
242 
243 /* I2C RTC */
244 #define CONFIG_RTC_M41T11		1
245 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
246 #define CONFIG_SYS_M41T11_BASE_YEAR	2000
247 
248 /* GPIO/EEPROM/SRAM */
249 #define CONFIG_DS4510
250 #define CONFIG_SYS_I2C_DS4510_ADDR	0x51
251 
252 /* GPIO */
253 #define CONFIG_PCA953X
254 #define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
255 #define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
256 #define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
257 #define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
258 #define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
259 
260 /*
261  * PU = pulled high, PD = pulled low
262  * I = input, O = output, IO = input/output
263  */
264 /* PCA9557 @ 0x18*/
265 #define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
266 #define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select */
267 #define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
268 #define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select */
269 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
270 #define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Set to 0 to enable NVM writing */
271 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2	0x40 /* VID2 of ISL6262 */
272 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3	0x80 /* VID3 of ISL6262 */
273 
274 /* PCA9557 @ 0x1c*/
275 #define CONFIG_SYS_PCA953X_XMC0_ROOT0		0x01 /* PU; Low if XMC is RC */
276 #define CONFIG_SYS_PCA953X_XMC0_MVMR0		0x02 /* XMC EEPROM write protect */
277 #define CONFIG_SYS_PCA953X_XMC0_WAKE		0x04 /* PU; XMC wake */
278 #define CONFIG_SYS_PCA953X_XMC0_BIST		0x08 /* PU; XMC built in self test */
279 #define CONFIG_SYS_PCA953X_XMC_PRESENT		0x10 /* PU; Low if XMC module installed */
280 #define CONFIG_SYS_PCA953X_PMC_PRESENT		0x20 /* PU; Low if PMC module installed */
281 #define CONFIG_SYS_PCA953X_PMC0_MONARCH		0x40 /* PMC monarch mode enable */
282 #define CONFIG_SYS_PCA953X_PMC0_EREADY		0x80 /* PU; PMC PCI eready */
283 
284 /* PCA9557 @ 0x1e*/
285 #define CONFIG_SYS_PCA953X_P0_GA0		0x01 /* PU; VPX Geographical address */
286 #define CONFIG_SYS_PCA953X_P0_GA1		0x02 /* PU; VPX Geographical address */
287 #define CONFIG_SYS_PCA953X_P0_GA2		0x04 /* PU; VPX Geographical address */
288 #define CONFIG_SYS_PCA953X_P0_GA3		0x08 /* PU; VPX Geographical address */
289 #define CONFIG_SYS_PCA953X_P0_GA4		0x10 /* PU; VPX Geographical address */
290 #define CONFIG_SYS_PCA953X_P0_GAP		0x20 /* PU; tied to VPX P0.GAP */
291 #define CONFIG_SYS_PCA953X_P1_SYSEN		0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
292 
293 /* PCA9557 @ 0x1f */
294 #define CONFIG_SYS_PCA953X_GPIO_VPX0		0x01 /* PU */
295 #define CONFIG_SYS_PCA953X_GPIO_VPX1		0x02 /* PU */
296 #define CONFIG_SYS_PCA953X_GPIO_VPX2		0x04 /* PU */
297 #define CONFIG_SYS_PCA953X_GPIO_VPX3		0x08 /* PU */
298 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL	0x10 /* PD; I2C master source for FRU SEEPROM */
299 
300 /*
301  * General PCI
302  * Memory space is mapped 1-1, but I/O space must start from 0.
303  */
304 /* PCIE1 - VPX P1 */
305 #define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
306 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
307 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
308 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
309 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
310 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
311 
312 /* PCIE2 - PEX8518 */
313 #define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
314 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
315 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
316 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
317 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
318 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
319 
320 /*
321  * Networking options
322  */
323 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
324 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
325 #define CONFIG_TSEC_TBI
326 #define CONFIG_MII		1	/* MII PHY management */
327 #define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
328 #define CONFIG_ETHPRIME		"eTSEC2"
329 
330 /*
331  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
332  * 1000mbps SGMII link
333  */
334 #define CONFIG_TSEC_TBICR_SETTINGS ( \
335 		TBICR_PHY_RESET \
336 		| TBICR_FULL_DUPLEX \
337 		| TBICR_SPEED1_SET \
338 		)
339 
340 #define CONFIG_TSEC1		1
341 #define CONFIG_TSEC1_NAME	"eTSEC1"
342 #define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
343 #define TSEC1_PHY_ADDR		1
344 #define TSEC1_PHYIDX		0
345 #define CONFIG_HAS_ETH0
346 
347 #define CONFIG_TSEC2		1
348 #define CONFIG_TSEC2_NAME	"eTSEC2"
349 #define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
350 #define TSEC2_PHY_ADDR		2
351 #define TSEC2_PHYIDX		0
352 #define CONFIG_HAS_ETH1
353 
354 /*
355  * Command configuration.
356  */
357 #define CONFIG_CMD_DS4510
358 #define CONFIG_CMD_DS4510_INFO
359 #define CONFIG_CMD_DTT
360 #define CONFIG_CMD_EEPROM
361 #define CONFIG_CMD_JFFS2
362 #define CONFIG_CMD_NAND
363 #define CONFIG_CMD_PCA953X
364 #define CONFIG_CMD_PCA953X_INFO
365 #define CONFIG_CMD_PCI
366 #define CONFIG_CMD_PCI_ENUM
367 #define CONFIG_CMD_REGINFO
368 
369 /*
370  * Miscellaneous configurable options
371  */
372 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
373 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
374 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
375 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
376 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
377 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
378 #define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
379 #define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
380 #define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
381 #define CONFIG_PANIC_HANG			/* do not reset board on panic */
382 #define CONFIG_PREBOOT				/* enable preboot variable */
383 #define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
384 
385 /*
386  * For booting Linux, the board info and command line data
387  * have to be in the first 16 MB of memory, since this is
388  * the maximum mapped by the Linux kernel during initialization.
389  */
390 #define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
391 #define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
392 
393 /*
394  * Environment Configuration
395  */
396 #define CONFIG_ENV_IS_IN_FLASH	1
397 #define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
398 #define CONFIG_ENV_SIZE		0x8000
399 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
400 
401 /*
402  * Flash memory map:
403  * fff80000 - ffffffff     Pri U-Boot (512 KB)
404  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
405  * fff00000 - fff3ffff     Pri FDT (256KB)
406  * fef00000 - ffefffff     Pri OS image (16MB)
407  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
408  *
409  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
410  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
411  * f7f00000 - f7f3ffff     Sec FDT (256KB)
412  * f6f00000 - f7efffff     Sec OS image (16MB)
413  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
414  */
415 #define CONFIG_UBOOT1_ENV_ADDR	__stringify(0xfff80000)
416 #define CONFIG_UBOOT2_ENV_ADDR	__stringify(0xf7f80000)
417 #define CONFIG_FDT1_ENV_ADDR	__stringify(0xfff00000)
418 #define CONFIG_FDT2_ENV_ADDR	__stringify(0xf7f00000)
419 #define CONFIG_OS1_ENV_ADDR	__stringify(0xfef00000)
420 #define CONFIG_OS2_ENV_ADDR	__stringify(0xf6f00000)
421 
422 #define CONFIG_PROG_UBOOT1						\
423 	"$download_cmd $loadaddr $ubootfile; "				\
424 	"if test $? -eq 0; then "					\
425 		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
426 		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
427 		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
428 		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
429 		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
430 		"if test $? -ne 0; then "				\
431 			"echo PROGRAM FAILED; "				\
432 		"else; "						\
433 			"echo PROGRAM SUCCEEDED; "			\
434 		"fi; "							\
435 	"else; "							\
436 		"echo DOWNLOAD FAILED; "				\
437 	"fi;"
438 
439 #define CONFIG_PROG_UBOOT2						\
440 	"$download_cmd $loadaddr $ubootfile; "				\
441 	"if test $? -eq 0; then "					\
442 		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
443 		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
444 		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
445 		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
446 		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
447 		"if test $? -ne 0; then "				\
448 			"echo PROGRAM FAILED; "				\
449 		"else; "						\
450 			"echo PROGRAM SUCCEEDED; "			\
451 		"fi; "							\
452 	"else; "							\
453 		"echo DOWNLOAD FAILED; "				\
454 	"fi;"
455 
456 #define CONFIG_BOOT_OS_NET						\
457 	"$download_cmd $osaddr $osfile; "				\
458 	"if test $? -eq 0; then "					\
459 		"if test -n $fdtaddr; then "				\
460 			"$download_cmd $fdtaddr $fdtfile; "		\
461 			"if test $? -eq 0; then "			\
462 				"bootm $osaddr - $fdtaddr; "		\
463 			"else; "					\
464 				"echo FDT DOWNLOAD FAILED; "		\
465 			"fi; "						\
466 		"else; "						\
467 			"bootm $osaddr; "				\
468 		"fi; "							\
469 	"else; "							\
470 		"echo OS DOWNLOAD FAILED; "				\
471 	"fi;"
472 
473 #define CONFIG_PROG_OS1							\
474 	"$download_cmd $osaddr $osfile; "				\
475 	"if test $? -eq 0; then "					\
476 		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
477 		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
478 		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
479 		"if test $? -ne 0; then "				\
480 			"echo OS PROGRAM FAILED; "			\
481 		"else; "						\
482 			"echo OS PROGRAM SUCCEEDED; "			\
483 		"fi; "							\
484 	"else; "							\
485 		"echo OS DOWNLOAD FAILED; "				\
486 	"fi;"
487 
488 #define CONFIG_PROG_OS2							\
489 	"$download_cmd $osaddr $osfile; "				\
490 	"if test $? -eq 0; then "					\
491 		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
492 		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
493 		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
494 		"if test $? -ne 0; then "				\
495 			"echo OS PROGRAM FAILED; "			\
496 		"else; "						\
497 			"echo OS PROGRAM SUCCEEDED; "			\
498 		"fi; "							\
499 	"else; "							\
500 		"echo OS DOWNLOAD FAILED; "				\
501 	"fi;"
502 
503 #define CONFIG_PROG_FDT1						\
504 	"$download_cmd $fdtaddr $fdtfile; "				\
505 	"if test $? -eq 0; then "					\
506 		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
507 		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
508 		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
509 		"if test $? -ne 0; then "				\
510 			"echo FDT PROGRAM FAILED; "			\
511 		"else; "						\
512 			"echo FDT PROGRAM SUCCEEDED; "			\
513 		"fi; "							\
514 	"else; "							\
515 		"echo FDT DOWNLOAD FAILED; "				\
516 	"fi;"
517 
518 #define CONFIG_PROG_FDT2						\
519 	"$download_cmd $fdtaddr $fdtfile; "				\
520 	"if test $? -eq 0; then "					\
521 		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
522 		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
523 		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
524 		"if test $? -ne 0; then "				\
525 			"echo FDT PROGRAM FAILED; "			\
526 		"else; "						\
527 			"echo FDT PROGRAM SUCCEEDED; "			\
528 		"fi; "							\
529 	"else; "							\
530 		"echo FDT DOWNLOAD FAILED; "				\
531 	"fi;"
532 
533 #define	CONFIG_EXTRA_ENV_SETTINGS					\
534 	"autoload=yes\0"						\
535 	"download_cmd=tftp\0"						\
536 	"console_args=console=ttyS0,115200\0"				\
537 	"root_args=root=/dev/nfs rw\0"					\
538 	"misc_args=ip=on\0"						\
539 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
540 	"bootfile=/home/user/file\0"					\
541 	"osfile=/home/user/board.uImage\0"				\
542 	"fdtfile=/home/user/board.dtb\0"				\
543 	"ubootfile=/home/user/u-boot.bin\0"				\
544 	"fdtaddr=0x1e00000\0"						\
545 	"osaddr=0x1000000\0"						\
546 	"loadaddr=0x1000000\0"						\
547 	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
548 	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
549 	"prog_os1="CONFIG_PROG_OS1"\0"					\
550 	"prog_os2="CONFIG_PROG_OS2"\0"					\
551 	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
552 	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
553 	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
554 	"bootcmd_flash1=run set_bootargs; "				\
555 		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
556 	"bootcmd_flash2=run set_bootargs; "				\
557 		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
558 	"bootcmd=run bootcmd_flash1\0"
559 #endif	/* __CONFIG_H */
560