1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 21 * MA 02111-1307 USA 22 */ 23 24 /* 25 * xpedite537x board configuration file 26 */ 27 #ifndef __CONFIG_H 28 #define __CONFIG_H 29 30 /* 31 * High Level Configuration Options 32 */ 33 #define CONFIG_BOOKE 1 /* BOOKE */ 34 #define CONFIG_E500 1 /* BOOKE e500 family */ 35 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ 36 #define CONFIG_MPC8572 1 37 #define CONFIG_XPEDITE5370 1 38 #define CONFIG_SYS_BOARD_NAME "XPedite5370" 39 #define CONFIG_SYS_FORM_3U_VPX 1 40 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 41 42 #ifndef CONFIG_SYS_TEXT_BASE 43 #define CONFIG_SYS_TEXT_BASE 0xfff80000 44 #endif 45 46 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 47 #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ 48 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 49 #define CONFIG_PCIE1 1 /* PCIE controler 1 */ 50 #define CONFIG_PCIE2 1 /* PCIE controler 2 */ 51 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 52 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 53 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 54 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 55 #define CONFIG_FSL_ELBC 1 56 57 /* 58 * Multicore config 59 */ 60 #define CONFIG_MP 61 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 62 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 63 64 /* 65 * DDR config 66 */ 67 #define CONFIG_FSL_DDR2 68 #undef CONFIG_FSL_DDR_INTERACTIVE 69 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 70 #define CONFIG_DDR_SPD 71 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 72 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 73 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 74 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 75 #define CONFIG_NUM_DDR_CONTROLLERS 2 76 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 77 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 78 #define CONFIG_DDR_ECC 79 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 80 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 81 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 82 #define CONFIG_VERY_BIG_RAM 83 84 #ifndef __ASSEMBLY__ 85 extern unsigned long get_board_sys_clk(unsigned long dummy); 86 extern unsigned long get_board_ddr_clk(unsigned long dummy); 87 #endif 88 89 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 90 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 91 92 /* 93 * These can be toggled for performance analysis, otherwise use default. 94 */ 95 #define CONFIG_L2_CACHE /* toggle L2 cache */ 96 #define CONFIG_BTB /* toggle branch predition */ 97 #define CONFIG_ENABLE_36BIT_PHYS 1 98 99 /* 100 * Base addresses -- Note these are effective addresses where the 101 * actual resources get mapped (not physical addresses) 102 */ 103 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 104 #define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ 105 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ 106 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 107 108 /* 109 * Diagnostics 110 */ 111 #define CONFIG_SYS_ALT_MEMTEST 112 #define CONFIG_SYS_MEMTEST_START 0x10000000 113 #define CONFIG_SYS_MEMTEST_END 0x20000000 114 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 115 CONFIG_SYS_POST_I2C) 116 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ 117 CONFIG_SYS_I2C_DS4510_ADDR, \ 118 CONFIG_SYS_I2C_EEPROM_ADDR, \ 119 CONFIG_SYS_I2C_LM90_ADDR, \ 120 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 121 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 122 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 123 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 124 CONFIG_SYS_I2C_PEX8518_ADDR, \ 125 CONFIG_SYS_I2C_RTC_ADDR} 126 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ 127 #define I2C_ADDR_IGNORE_LIST {0x50} 128 129 /* 130 * Memory map 131 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 132 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 133 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 134 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 135 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 136 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 137 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 138 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 139 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 140 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 141 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 142 */ 143 144 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 145 146 /* 147 * NAND flash configuration 148 */ 149 #define CONFIG_SYS_NAND_BASE 0xef800000 150 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 151 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 152 CONFIG_SYS_NAND_BASE2} 153 #define CONFIG_SYS_MAX_NAND_DEVICE 2 154 #define CONFIG_MTD_NAND_VERIFY_WRITE 155 #define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */ 156 #define CONFIG_NAND_FSL_ELBC 157 158 /* 159 * NOR flash configuration 160 */ 161 #define CONFIG_SYS_FLASH_BASE 0xf8000000 162 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 163 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 164 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 165 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 166 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 167 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 168 #define CONFIG_FLASH_CFI_DRIVER 169 #define CONFIG_SYS_FLASH_CFI 170 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 171 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 172 {0xf7f40000, 0xc0000} } 173 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 174 175 /* 176 * Chip select configuration 177 */ 178 /* NOR Flash 0 on CS0 */ 179 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 180 BR_PS_16 | \ 181 BR_V) 182 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 183 OR_GPCM_CSNT | \ 184 OR_GPCM_XACS | \ 185 OR_GPCM_ACS_DIV2 | \ 186 OR_GPCM_SCY_8 | \ 187 OR_GPCM_TRLX | \ 188 OR_GPCM_EHTR | \ 189 OR_GPCM_EAD) 190 191 /* NOR Flash 1 on CS1 */ 192 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 193 BR_PS_16 | \ 194 BR_V) 195 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 196 197 /* NAND flash on CS2 */ 198 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 199 (2<<BR_DECC_SHIFT) | \ 200 BR_PS_8 | \ 201 BR_MS_FCM | \ 202 BR_V) 203 204 /* NAND flash on CS2 */ 205 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 206 OR_FCM_PGS | \ 207 OR_FCM_CSCT | \ 208 OR_FCM_CST | \ 209 OR_FCM_CHT | \ 210 OR_FCM_SCY_1 | \ 211 OR_FCM_TRLX | \ 212 OR_FCM_EHTR) 213 214 /* NAND flash on CS3 */ 215 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 216 (2<<BR_DECC_SHIFT) | \ 217 BR_PS_8 | \ 218 BR_MS_FCM | \ 219 BR_V) 220 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 221 222 /* 223 * Use L1 as initial stack 224 */ 225 #define CONFIG_SYS_INIT_RAM_LOCK 1 226 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 227 #define CONFIG_SYS_INIT_RAM_END 0x00004000 228 229 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ 230 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 231 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 232 233 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 234 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 235 236 /* 237 * Serial Port 238 */ 239 #define CONFIG_CONS_INDEX 1 240 #define CONFIG_SYS_NS16550 241 #define CONFIG_SYS_NS16550_SERIAL 242 #define CONFIG_SYS_NS16550_REG_SIZE 1 243 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 244 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 245 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 246 #define CONFIG_SYS_BAUDRATE_TABLE \ 247 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 248 #define CONFIG_BAUDRATE 115200 249 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 250 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 251 252 /* 253 * Use the HUSH parser 254 */ 255 #define CONFIG_SYS_HUSH_PARSER 256 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 257 258 /* 259 * Pass open firmware flat tree 260 */ 261 #define CONFIG_OF_LIBFDT 1 262 #define CONFIG_OF_BOARD_SETUP 1 263 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 264 265 /* 266 * I2C 267 */ 268 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 269 #define CONFIG_HARD_I2C /* I2C with hardware support */ 270 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 271 #define CONFIG_SYS_I2C_SLAVE 0x7F 272 #define CONFIG_SYS_I2C_OFFSET 0x3000 273 #define CONFIG_SYS_I2C2_OFFSET 0x3100 274 #define CONFIG_I2C_MULTI_BUS 275 276 /* PEX8518 slave I2C interface */ 277 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 278 279 /* I2C DS1631 temperature sensor */ 280 #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 281 #define CONFIG_DTT_DS1621 282 #define CONFIG_DTT_SENSORS { 0 } 283 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 284 285 /* I2C EEPROM - AT24C128B */ 286 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 287 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 288 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 289 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 290 291 /* I2C RTC */ 292 #define CONFIG_RTC_M41T11 1 293 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 294 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 295 296 /* GPIO/EEPROM/SRAM */ 297 #define CONFIG_DS4510 298 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 299 300 /* GPIO */ 301 #define CONFIG_PCA953X 302 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 303 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 304 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 305 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 306 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 307 308 /* 309 * PU = pulled high, PD = pulled low 310 * I = input, O = output, IO = input/output 311 */ 312 /* PCA9557 @ 0x18*/ 313 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 314 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 315 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 316 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 317 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 318 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 319 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ 320 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ 321 322 /* PCA9557 @ 0x1c*/ 323 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 324 #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ 325 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 326 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 327 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 328 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 329 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 330 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 331 332 /* PCA9557 @ 0x1e*/ 333 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 334 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 335 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 336 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 337 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 338 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ 339 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ 340 341 /* PCA9557 @ 0x1f */ 342 #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ 343 #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ 344 #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ 345 #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ 346 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ 347 348 /* 349 * General PCI 350 * Memory space is mapped 1-1, but I/O space must start from 0. 351 */ 352 /* PCIE1 - VPX P1 */ 353 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 354 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 355 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 356 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 357 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 358 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 359 360 /* PCIE2 - PEX8518 */ 361 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 362 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 363 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 364 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 365 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 366 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 367 368 /* 369 * Networking options 370 */ 371 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 372 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 373 #define CONFIG_NET_MULTI 1 374 #define CONFIG_TSEC_TBI 375 #define CONFIG_MII 1 /* MII PHY management */ 376 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 377 #define CONFIG_ETHPRIME "eTSEC2" 378 379 #define CONFIG_TSEC1 1 380 #define CONFIG_TSEC1_NAME "eTSEC1" 381 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 382 #define TSEC1_PHY_ADDR 1 383 #define TSEC1_PHYIDX 0 384 #define CONFIG_HAS_ETH0 385 386 #define CONFIG_TSEC2 1 387 #define CONFIG_TSEC2_NAME "eTSEC2" 388 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 389 #define TSEC2_PHY_ADDR 2 390 #define TSEC2_PHYIDX 0 391 #define CONFIG_HAS_ETH1 392 393 /* 394 * Command configuration. 395 */ 396 #include <config_cmd_default.h> 397 398 #define CONFIG_CMD_ASKENV 399 #define CONFIG_CMD_DATE 400 #define CONFIG_CMD_DHCP 401 #define CONFIG_CMD_DS4510 402 #define CONFIG_CMD_DS4510_INFO 403 #define CONFIG_CMD_DTT 404 #define CONFIG_CMD_EEPROM 405 #define CONFIG_CMD_ELF 406 #define CONFIG_CMD_FLASH 407 #define CONFIG_CMD_I2C 408 #define CONFIG_CMD_JFFS2 409 #define CONFIG_CMD_MII 410 #define CONFIG_CMD_NAND 411 #define CONFIG_CMD_NET 412 #define CONFIG_CMD_PCA953X 413 #define CONFIG_CMD_PCA953X_INFO 414 #define CONFIG_CMD_PCI 415 #define CONFIG_CMD_PCI_ENUM 416 #define CONFIG_CMD_PING 417 #define CONFIG_CMD_SAVEENV 418 #define CONFIG_CMD_SNTP 419 #define CONFIG_CMD_REGINFO 420 421 /* 422 * Miscellaneous configurable options 423 */ 424 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 425 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 426 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 427 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 428 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 429 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 430 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 431 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 432 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 433 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 434 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 435 #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ 436 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 437 #define CONFIG_PREBOOT /* enable preboot variable */ 438 #define CONFIG_FIT 1 439 #define CONFIG_FIT_VERBOSE 1 440 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 441 442 /* 443 * For booting Linux, the board info and command line data 444 * have to be in the first 16 MB of memory, since this is 445 * the maximum mapped by the Linux kernel during initialization. 446 */ 447 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 448 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 449 450 /* 451 * Environment Configuration 452 */ 453 #define CONFIG_ENV_IS_IN_FLASH 1 454 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 455 #define CONFIG_ENV_SIZE 0x8000 456 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 457 458 /* 459 * Flash memory map: 460 * fff80000 - ffffffff Pri U-Boot (512 KB) 461 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 462 * fff00000 - fff3ffff Pri FDT (256KB) 463 * fef00000 - ffefffff Pri OS image (16MB) 464 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 465 * 466 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 467 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 468 * f7f00000 - f7f3ffff Sec FDT (256KB) 469 * f6f00000 - f7efffff Sec OS image (16MB) 470 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 471 */ 472 #define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000) 473 #define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000) 474 #define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000) 475 #define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000) 476 #define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) 477 #define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000) 478 479 #define CONFIG_PROG_UBOOT1 \ 480 "$download_cmd $loadaddr $ubootfile; " \ 481 "if test $? -eq 0; then " \ 482 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 483 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 484 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 485 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 486 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 487 "if test $? -ne 0; then " \ 488 "echo PROGRAM FAILED; " \ 489 "else; " \ 490 "echo PROGRAM SUCCEEDED; " \ 491 "fi; " \ 492 "else; " \ 493 "echo DOWNLOAD FAILED; " \ 494 "fi;" 495 496 #define CONFIG_PROG_UBOOT2 \ 497 "$download_cmd $loadaddr $ubootfile; " \ 498 "if test $? -eq 0; then " \ 499 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 500 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 501 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 502 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 503 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 504 "if test $? -ne 0; then " \ 505 "echo PROGRAM FAILED; " \ 506 "else; " \ 507 "echo PROGRAM SUCCEEDED; " \ 508 "fi; " \ 509 "else; " \ 510 "echo DOWNLOAD FAILED; " \ 511 "fi;" 512 513 #define CONFIG_BOOT_OS_NET \ 514 "$download_cmd $osaddr $osfile; " \ 515 "if test $? -eq 0; then " \ 516 "if test -n $fdtaddr; then " \ 517 "$download_cmd $fdtaddr $fdtfile; " \ 518 "if test $? -eq 0; then " \ 519 "bootm $osaddr - $fdtaddr; " \ 520 "else; " \ 521 "echo FDT DOWNLOAD FAILED; " \ 522 "fi; " \ 523 "else; " \ 524 "bootm $osaddr; " \ 525 "fi; " \ 526 "else; " \ 527 "echo OS DOWNLOAD FAILED; " \ 528 "fi;" 529 530 #define CONFIG_PROG_OS1 \ 531 "$download_cmd $osaddr $osfile; " \ 532 "if test $? -eq 0; then " \ 533 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 534 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 535 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 536 "if test $? -ne 0; then " \ 537 "echo OS PROGRAM FAILED; " \ 538 "else; " \ 539 "echo OS PROGRAM SUCCEEDED; " \ 540 "fi; " \ 541 "else; " \ 542 "echo OS DOWNLOAD FAILED; " \ 543 "fi;" 544 545 #define CONFIG_PROG_OS2 \ 546 "$download_cmd $osaddr $osfile; " \ 547 "if test $? -eq 0; then " \ 548 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 549 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 550 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 551 "if test $? -ne 0; then " \ 552 "echo OS PROGRAM FAILED; " \ 553 "else; " \ 554 "echo OS PROGRAM SUCCEEDED; " \ 555 "fi; " \ 556 "else; " \ 557 "echo OS DOWNLOAD FAILED; " \ 558 "fi;" 559 560 #define CONFIG_PROG_FDT1 \ 561 "$download_cmd $fdtaddr $fdtfile; " \ 562 "if test $? -eq 0; then " \ 563 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 564 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 565 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 566 "if test $? -ne 0; then " \ 567 "echo FDT PROGRAM FAILED; " \ 568 "else; " \ 569 "echo FDT PROGRAM SUCCEEDED; " \ 570 "fi; " \ 571 "else; " \ 572 "echo FDT DOWNLOAD FAILED; " \ 573 "fi;" 574 575 #define CONFIG_PROG_FDT2 \ 576 "$download_cmd $fdtaddr $fdtfile; " \ 577 "if test $? -eq 0; then " \ 578 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 579 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 580 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 581 "if test $? -ne 0; then " \ 582 "echo FDT PROGRAM FAILED; " \ 583 "else; " \ 584 "echo FDT PROGRAM SUCCEEDED; " \ 585 "fi; " \ 586 "else; " \ 587 "echo FDT DOWNLOAD FAILED; " \ 588 "fi;" 589 590 #define CONFIG_EXTRA_ENV_SETTINGS \ 591 "autoload=yes\0" \ 592 "download_cmd=tftp\0" \ 593 "console_args=console=ttyS0,115200\0" \ 594 "root_args=root=/dev/nfs rw\0" \ 595 "misc_args=ip=on\0" \ 596 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 597 "bootfile=/home/user/file\0" \ 598 "osfile=/home/user/board.uImage\0" \ 599 "fdtfile=/home/user/board.dtb\0" \ 600 "ubootfile=/home/user/u-boot.bin\0" \ 601 "fdtaddr=c00000\0" \ 602 "osaddr=0x1000000\0" \ 603 "loadaddr=0x1000000\0" \ 604 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 605 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 606 "prog_os1="CONFIG_PROG_OS1"\0" \ 607 "prog_os2="CONFIG_PROG_OS2"\0" \ 608 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 609 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 610 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 611 "bootcmd_flash1=run set_bootargs; " \ 612 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 613 "bootcmd_flash2=run set_bootargs; " \ 614 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 615 "bootcmd=run bootcmd_flash1\0" 616 #endif /* __CONFIG_H */ 617