1 /*
2  * Copyright 2008 Extreme Engineering Solutions, Inc.
3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
4  *
5  * See file CREDITS for list of people who contributed to this
6  * project.
7  *
8  * This program is free software; you can redistribute it and/or
9  * modify it under the terms of the GNU General Public License as
10  * published by the Free Software Foundation; either version 2 of
11  * the License, or (at your option) any later version.
12  *
13  * This program is distributed in the hope that it will be useful,
14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16  * GNU General Public License for more details.
17  *
18  * You should have received a copy of the GNU General Public License
19  * along with this program; if not, write to the Free Software
20  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21  * MA 02111-1307 USA
22  */
23 
24 /*
25  * xpedite537x board configuration file
26  */
27 #ifndef __CONFIG_H
28 #define __CONFIG_H
29 
30 /*
31  * High Level Configuration Options
32  */
33 #define CONFIG_BOOKE		1	/* BOOKE */
34 #define CONFIG_E500		1	/* BOOKE e500 family */
35 #define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
36 #define CONFIG_MPC8572		1
37 #define CONFIG_XPEDITE5370	1
38 #define CONFIG_SYS_BOARD_NAME	"XPedite5370"
39 #define CONFIG_SYS_FORM_3U_VPX	1
40 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
41 
42 #ifndef CONFIG_SYS_TEXT_BASE
43 #define CONFIG_SYS_TEXT_BASE	0xfff80000
44 #endif
45 
46 #define CONFIG_PCI		1	/* Enable PCI/PCIE */
47 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play */
48 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
49 #define CONFIG_PCIE1		1	/* PCIE controler 1 */
50 #define CONFIG_PCIE2		1	/* PCIE controler 2 */
51 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
52 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
53 #define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
54 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
55 #define CONFIG_FSL_ELBC		1
56 
57 /*
58  * Multicore config
59  */
60 #define CONFIG_MP
61 #define CONFIG_BPTR_VIRT_ADDR	0xee000000	/* virt boot page address */
62 #define CONFIG_MPC8xxx_DISABLE_BPTR		/* Don't leave BPTR enabled */
63 
64 /*
65  * DDR config
66  */
67 #define CONFIG_FSL_DDR2
68 #undef CONFIG_FSL_DDR_INTERACTIVE
69 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
70 #define CONFIG_DDR_SPD
71 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
72 #define SPD_EEPROM_ADDRESS1		0x54	/* Both channels use the */
73 #define SPD_EEPROM_ADDRESS2		0x54	/* same SPD data         */
74 #define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
75 #define CONFIG_NUM_DDR_CONTROLLERS	2
76 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
77 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
78 #define CONFIG_DDR_ECC
79 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
80 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000 /* DDR is system memory*/
81 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
82 #define CONFIG_VERY_BIG_RAM
83 
84 #ifndef __ASSEMBLY__
85 extern unsigned long get_board_sys_clk(unsigned long dummy);
86 extern unsigned long get_board_ddr_clk(unsigned long dummy);
87 #endif
88 
89 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
90 #define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */
91 
92 /*
93  * These can be toggled for performance analysis, otherwise use default.
94  */
95 #define CONFIG_L2_CACHE			/* toggle L2 cache */
96 #define CONFIG_BTB			/* toggle branch predition */
97 #define CONFIG_ENABLE_36BIT_PHYS	1
98 
99 #define CONFIG_SYS_CCSRBAR		0xef000000
100 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
101 
102 /*
103  * Diagnostics
104  */
105 #define CONFIG_SYS_ALT_MEMTEST
106 #define CONFIG_SYS_MEMTEST_START	0x10000000
107 #define CONFIG_SYS_MEMTEST_END		0x20000000
108 #define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
109 					 CONFIG_SYS_POST_I2C)
110 #define I2C_ADDR_LIST			{CONFIG_SYS_I2C_DS1621_ADDR,	\
111 					 CONFIG_SYS_I2C_DS4510_ADDR,	\
112 					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
113 					 CONFIG_SYS_I2C_LM90_ADDR,	\
114 					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
115 					 CONFIG_SYS_I2C_PCA953X_ADDR1,	\
116 					 CONFIG_SYS_I2C_PCA953X_ADDR2,	\
117 					 CONFIG_SYS_I2C_PCA953X_ADDR3,	\
118 					 CONFIG_SYS_I2C_PEX8518_ADDR,	\
119 					 CONFIG_SYS_I2C_RTC_ADDR}
120 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
121 #define I2C_ADDR_IGNORE_LIST		{0x50}
122 
123 /*
124  * Memory map
125  * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
126  * 0x8000_0000	0xbfff_ffff	PCIe1 Mem		1G non-cacheable
127  * 0xc000_0000	0xcfff_ffff	PCIe2 Mem		256M non-cacheable
128  * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
129  * 0xe800_0000	0xe87f_ffff	PCIe1 IO		8M non-cacheable
130  * 0xe880_0000	0xe8ff_ffff	PCIe2 IO		8M non-cacheable
131  * 0xee00_0000	0xee00_ffff	Boot page translation	4K non-cacheable
132  * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
133  * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
134  * 0xf000_0000	0xf7ff_ffff	NOR Flash 2		128M non-cacheable
135  * 0xf800_0000	0xffff_ffff	NOR Flash 1		128M non-cacheable
136  */
137 
138 #define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)
139 
140 /*
141  * NAND flash configuration
142  */
143 #define CONFIG_SYS_NAND_BASE		0xef800000
144 #define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
145 #define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE, \
146 					 CONFIG_SYS_NAND_BASE2}
147 #define CONFIG_SYS_MAX_NAND_DEVICE	2
148 #define CONFIG_MTD_NAND_VERIFY_WRITE
149 #define CONFIG_SYS_NAND_QUIET_TEST	/* 2nd NAND flash not always populated */
150 #define CONFIG_NAND_FSL_ELBC
151 
152 /*
153  * NOR flash configuration
154  */
155 #define CONFIG_SYS_FLASH_BASE		0xf8000000
156 #define CONFIG_SYS_FLASH_BASE2		0xf0000000
157 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
158 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
159 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
160 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
161 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
162 #define CONFIG_FLASH_CFI_DRIVER
163 #define CONFIG_SYS_FLASH_CFI
164 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
165 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
166 						  {0xf7f40000, 0xc0000} }
167 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
168 
169 /*
170  * Chip select configuration
171  */
172 /* NOR Flash 0 on CS0 */
173 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
174 				 BR_PS_16		| \
175 				 BR_V)
176 #define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		| \
177 				 OR_GPCM_CSNT		| \
178 				 OR_GPCM_XACS		| \
179 				 OR_GPCM_ACS_DIV2	| \
180 				 OR_GPCM_SCY_8		| \
181 				 OR_GPCM_TRLX		| \
182 				 OR_GPCM_EHTR		| \
183 				 OR_GPCM_EAD)
184 
185 /* NOR Flash 1 on CS1 */
186 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
187 				 BR_PS_16		| \
188 				 BR_V)
189 #define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
190 
191 /* NAND flash on CS2 */
192 #define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
193 				 (2<<BR_DECC_SHIFT)	| \
194 				 BR_PS_8		| \
195 				 BR_MS_FCM		| \
196 				 BR_V)
197 
198 /* NAND flash on CS2 */
199 #define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB	| \
200 				 OR_FCM_PGS	| \
201 				 OR_FCM_CSCT	| \
202 				 OR_FCM_CST	| \
203 				 OR_FCM_CHT	| \
204 				 OR_FCM_SCY_1	| \
205 				 OR_FCM_TRLX	| \
206 				 OR_FCM_EHTR)
207 
208 /* NAND flash on CS3 */
209 #define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
210 				 (2<<BR_DECC_SHIFT)	| \
211 				 BR_PS_8		| \
212 				 BR_MS_FCM		| \
213 				 BR_V)
214 #define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
215 
216 /*
217  * Use L1 as initial stack
218  */
219 #define CONFIG_SYS_INIT_RAM_LOCK	1
220 #define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
221 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
222 
223 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
224 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
225 
226 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
227 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
228 
229 /*
230  * Serial Port
231  */
232 #define CONFIG_CONS_INDEX		1
233 #define CONFIG_SYS_NS16550
234 #define CONFIG_SYS_NS16550_SERIAL
235 #define CONFIG_SYS_NS16550_REG_SIZE	1
236 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
237 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
238 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
239 #define CONFIG_SYS_BAUDRATE_TABLE	\
240 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
241 #define CONFIG_BAUDRATE			115200
242 #define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
243 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
244 
245 /*
246  * Use the HUSH parser
247  */
248 #define CONFIG_SYS_HUSH_PARSER
249 
250 /*
251  * Pass open firmware flat tree
252  */
253 #define CONFIG_OF_LIBFDT		1
254 #define CONFIG_OF_BOARD_SETUP		1
255 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
256 
257 /*
258  * I2C
259  */
260 #define CONFIG_FSL_I2C				/* Use FSL common I2C driver */
261 #define CONFIG_HARD_I2C				/* I2C with hardware support */
262 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
263 #define CONFIG_SYS_I2C_SLAVE		0x7F
264 #define CONFIG_SYS_I2C_OFFSET		0x3000
265 #define CONFIG_SYS_I2C2_OFFSET		0x3100
266 #define CONFIG_I2C_MULTI_BUS
267 
268 /* PEX8518 slave I2C interface */
269 #define CONFIG_SYS_I2C_PEX8518_ADDR	0x70
270 
271 /* I2C DS1631 temperature sensor */
272 #define CONFIG_SYS_I2C_DS1621_ADDR	0x48
273 #define CONFIG_DTT_DS1621
274 #define CONFIG_DTT_SENSORS		{ 0 }
275 #define CONFIG_SYS_I2C_LM90_ADDR	0x4c
276 
277 /* I2C EEPROM - AT24C128B */
278 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
279 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
280 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
281 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
282 
283 /* I2C RTC */
284 #define CONFIG_RTC_M41T11		1
285 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
286 #define CONFIG_SYS_M41T11_BASE_YEAR	2000
287 
288 /* GPIO/EEPROM/SRAM */
289 #define CONFIG_DS4510
290 #define CONFIG_SYS_I2C_DS4510_ADDR	0x51
291 
292 /* GPIO */
293 #define CONFIG_PCA953X
294 #define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
295 #define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
296 #define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
297 #define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
298 #define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
299 
300 /*
301  * PU = pulled high, PD = pulled low
302  * I = input, O = output, IO = input/output
303  */
304 /* PCA9557 @ 0x18*/
305 #define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
306 #define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select */
307 #define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
308 #define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select */
309 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
310 #define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Set to 0 to enable NVM writing */
311 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2	0x40 /* VID2 of ISL6262 */
312 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3	0x80 /* VID3 of ISL6262 */
313 
314 /* PCA9557 @ 0x1c*/
315 #define CONFIG_SYS_PCA953X_XMC0_ROOT0		0x01 /* PU; Low if XMC is RC */
316 #define CONFIG_SYS_PCA953X_XMC0_MVMR0		0x02 /* XMC EEPROM write protect */
317 #define CONFIG_SYS_PCA953X_XMC0_WAKE		0x04 /* PU; XMC wake */
318 #define CONFIG_SYS_PCA953X_XMC0_BIST		0x08 /* PU; XMC built in self test */
319 #define CONFIG_SYS_PCA953X_XMC_PRESENT		0x10 /* PU; Low if XMC module installed */
320 #define CONFIG_SYS_PCA953X_PMC_PRESENT		0x20 /* PU; Low if PMC module installed */
321 #define CONFIG_SYS_PCA953X_PMC0_MONARCH		0x40 /* PMC monarch mode enable */
322 #define CONFIG_SYS_PCA953X_PMC0_EREADY		0x80 /* PU; PMC PCI eready */
323 
324 /* PCA9557 @ 0x1e*/
325 #define CONFIG_SYS_PCA953X_P0_GA0		0x01 /* PU; VPX Geographical address */
326 #define CONFIG_SYS_PCA953X_P0_GA1		0x02 /* PU; VPX Geographical address */
327 #define CONFIG_SYS_PCA953X_P0_GA2		0x04 /* PU; VPX Geographical address */
328 #define CONFIG_SYS_PCA953X_P0_GA3		0x08 /* PU; VPX Geographical address */
329 #define CONFIG_SYS_PCA953X_P0_GA4		0x10 /* PU; VPX Geographical address */
330 #define CONFIG_SYS_PCA953X_P0_GAP		0x20 /* PU; tied to VPX P0.GAP */
331 #define CONFIG_SYS_PCA953X_P1_SYSEN		0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
332 
333 /* PCA9557 @ 0x1f */
334 #define CONFIG_SYS_PCA953X_GPIO_VPX0		0x01 /* PU */
335 #define CONFIG_SYS_PCA953X_GPIO_VPX1		0x02 /* PU */
336 #define CONFIG_SYS_PCA953X_GPIO_VPX2		0x04 /* PU */
337 #define CONFIG_SYS_PCA953X_GPIO_VPX3		0x08 /* PU */
338 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL	0x10 /* PD; I2C master source for FRU SEEPROM */
339 
340 /*
341  * General PCI
342  * Memory space is mapped 1-1, but I/O space must start from 0.
343  */
344 /* PCIE1 - VPX P1 */
345 #define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
346 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
347 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
348 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
349 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
350 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
351 
352 /* PCIE2 - PEX8518 */
353 #define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
354 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
355 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
356 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
357 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
358 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
359 
360 /*
361  * Networking options
362  */
363 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
364 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
365 #define CONFIG_TSEC_TBI
366 #define CONFIG_MII		1	/* MII PHY management */
367 #define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
368 #define CONFIG_ETHPRIME		"eTSEC2"
369 
370 /*
371  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
372  * 1000mbps SGMII link
373  */
374 #define CONFIG_TSEC_TBICR_SETTINGS ( \
375 		TBICR_PHY_RESET \
376 		| TBICR_FULL_DUPLEX \
377 		| TBICR_SPEED1_SET \
378 		)
379 
380 #define CONFIG_TSEC1		1
381 #define CONFIG_TSEC1_NAME	"eTSEC1"
382 #define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
383 #define TSEC1_PHY_ADDR		1
384 #define TSEC1_PHYIDX		0
385 #define CONFIG_HAS_ETH0
386 
387 #define CONFIG_TSEC2		1
388 #define CONFIG_TSEC2_NAME	"eTSEC2"
389 #define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
390 #define TSEC2_PHY_ADDR		2
391 #define TSEC2_PHYIDX		0
392 #define CONFIG_HAS_ETH1
393 
394 /*
395  * Command configuration.
396  */
397 #include <config_cmd_default.h>
398 
399 #define CONFIG_CMD_ASKENV
400 #define CONFIG_CMD_DATE
401 #define CONFIG_CMD_DHCP
402 #define CONFIG_CMD_DS4510
403 #define CONFIG_CMD_DS4510_INFO
404 #define CONFIG_CMD_DTT
405 #define CONFIG_CMD_EEPROM
406 #define CONFIG_CMD_ELF
407 #define CONFIG_CMD_FLASH
408 #define CONFIG_CMD_I2C
409 #define CONFIG_CMD_JFFS2
410 #define CONFIG_CMD_MII
411 #define CONFIG_CMD_NAND
412 #define CONFIG_CMD_NET
413 #define CONFIG_CMD_PCA953X
414 #define CONFIG_CMD_PCA953X_INFO
415 #define CONFIG_CMD_PCI
416 #define CONFIG_CMD_PCI_ENUM
417 #define CONFIG_CMD_PING
418 #define CONFIG_CMD_SAVEENV
419 #define CONFIG_CMD_SNTP
420 #define CONFIG_CMD_REGINFO
421 
422 /*
423  * Miscellaneous configurable options
424  */
425 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
426 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
427 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
428 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
429 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
430 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
431 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
432 #define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
433 #define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
434 #define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
435 #define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
436 #define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
437 #define CONFIG_PANIC_HANG			/* do not reset board on panic */
438 #define CONFIG_PREBOOT				/* enable preboot variable */
439 #define CONFIG_FIT		1
440 #define CONFIG_FIT_VERBOSE	1
441 #define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
442 
443 /*
444  * For booting Linux, the board info and command line data
445  * have to be in the first 16 MB of memory, since this is
446  * the maximum mapped by the Linux kernel during initialization.
447  */
448 #define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
449 #define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
450 
451 /*
452  * Environment Configuration
453  */
454 #define CONFIG_ENV_IS_IN_FLASH	1
455 #define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
456 #define CONFIG_ENV_SIZE		0x8000
457 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
458 
459 /*
460  * Flash memory map:
461  * fff80000 - ffffffff     Pri U-Boot (512 KB)
462  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
463  * fff00000 - fff3ffff     Pri FDT (256KB)
464  * fef00000 - ffefffff     Pri OS image (16MB)
465  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
466  *
467  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
468  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
469  * f7f00000 - f7f3ffff     Sec FDT (256KB)
470  * f6f00000 - f7efffff     Sec OS image (16MB)
471  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
472  */
473 #define CONFIG_UBOOT1_ENV_ADDR	MK_STR(0xfff80000)
474 #define CONFIG_UBOOT2_ENV_ADDR	MK_STR(0xf7f80000)
475 #define CONFIG_FDT1_ENV_ADDR	MK_STR(0xfff00000)
476 #define CONFIG_FDT2_ENV_ADDR	MK_STR(0xf7f00000)
477 #define CONFIG_OS1_ENV_ADDR	MK_STR(0xfef00000)
478 #define CONFIG_OS2_ENV_ADDR	MK_STR(0xf6f00000)
479 
480 #define CONFIG_PROG_UBOOT1						\
481 	"$download_cmd $loadaddr $ubootfile; "				\
482 	"if test $? -eq 0; then "					\
483 		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
484 		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
485 		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
486 		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
487 		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
488 		"if test $? -ne 0; then "				\
489 			"echo PROGRAM FAILED; "				\
490 		"else; "						\
491 			"echo PROGRAM SUCCEEDED; "			\
492 		"fi; "							\
493 	"else; "							\
494 		"echo DOWNLOAD FAILED; "				\
495 	"fi;"
496 
497 #define CONFIG_PROG_UBOOT2						\
498 	"$download_cmd $loadaddr $ubootfile; "				\
499 	"if test $? -eq 0; then "					\
500 		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
501 		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
502 		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
503 		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
504 		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
505 		"if test $? -ne 0; then "				\
506 			"echo PROGRAM FAILED; "				\
507 		"else; "						\
508 			"echo PROGRAM SUCCEEDED; "			\
509 		"fi; "							\
510 	"else; "							\
511 		"echo DOWNLOAD FAILED; "				\
512 	"fi;"
513 
514 #define CONFIG_BOOT_OS_NET						\
515 	"$download_cmd $osaddr $osfile; "				\
516 	"if test $? -eq 0; then "					\
517 		"if test -n $fdtaddr; then "				\
518 			"$download_cmd $fdtaddr $fdtfile; "		\
519 			"if test $? -eq 0; then "			\
520 				"bootm $osaddr - $fdtaddr; "		\
521 			"else; "					\
522 				"echo FDT DOWNLOAD FAILED; "		\
523 			"fi; "						\
524 		"else; "						\
525 			"bootm $osaddr; "				\
526 		"fi; "							\
527 	"else; "							\
528 		"echo OS DOWNLOAD FAILED; "				\
529 	"fi;"
530 
531 #define CONFIG_PROG_OS1							\
532 	"$download_cmd $osaddr $osfile; "				\
533 	"if test $? -eq 0; then "					\
534 		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
535 		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
536 		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
537 		"if test $? -ne 0; then "				\
538 			"echo OS PROGRAM FAILED; "			\
539 		"else; "						\
540 			"echo OS PROGRAM SUCCEEDED; "			\
541 		"fi; "							\
542 	"else; "							\
543 		"echo OS DOWNLOAD FAILED; "				\
544 	"fi;"
545 
546 #define CONFIG_PROG_OS2							\
547 	"$download_cmd $osaddr $osfile; "				\
548 	"if test $? -eq 0; then "					\
549 		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
550 		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
551 		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
552 		"if test $? -ne 0; then "				\
553 			"echo OS PROGRAM FAILED; "			\
554 		"else; "						\
555 			"echo OS PROGRAM SUCCEEDED; "			\
556 		"fi; "							\
557 	"else; "							\
558 		"echo OS DOWNLOAD FAILED; "				\
559 	"fi;"
560 
561 #define CONFIG_PROG_FDT1						\
562 	"$download_cmd $fdtaddr $fdtfile; "				\
563 	"if test $? -eq 0; then "					\
564 		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
565 		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
566 		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
567 		"if test $? -ne 0; then "				\
568 			"echo FDT PROGRAM FAILED; "			\
569 		"else; "						\
570 			"echo FDT PROGRAM SUCCEEDED; "			\
571 		"fi; "							\
572 	"else; "							\
573 		"echo FDT DOWNLOAD FAILED; "				\
574 	"fi;"
575 
576 #define CONFIG_PROG_FDT2						\
577 	"$download_cmd $fdtaddr $fdtfile; "				\
578 	"if test $? -eq 0; then "					\
579 		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
580 		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
581 		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
582 		"if test $? -ne 0; then "				\
583 			"echo FDT PROGRAM FAILED; "			\
584 		"else; "						\
585 			"echo FDT PROGRAM SUCCEEDED; "			\
586 		"fi; "							\
587 	"else; "							\
588 		"echo FDT DOWNLOAD FAILED; "				\
589 	"fi;"
590 
591 #define	CONFIG_EXTRA_ENV_SETTINGS					\
592 	"autoload=yes\0"						\
593 	"download_cmd=tftp\0"						\
594 	"console_args=console=ttyS0,115200\0"				\
595 	"root_args=root=/dev/nfs rw\0"					\
596 	"misc_args=ip=on\0"						\
597 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
598 	"bootfile=/home/user/file\0"					\
599 	"osfile=/home/user/board.uImage\0"				\
600 	"fdtfile=/home/user/board.dtb\0"				\
601 	"ubootfile=/home/user/u-boot.bin\0"				\
602 	"fdtaddr=c00000\0"						\
603 	"osaddr=0x1000000\0"						\
604 	"loadaddr=0x1000000\0"						\
605 	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
606 	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
607 	"prog_os1="CONFIG_PROG_OS1"\0"					\
608 	"prog_os2="CONFIG_PROG_OS2"\0"					\
609 	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
610 	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
611 	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
612 	"bootcmd_flash1=run set_bootargs; "				\
613 		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
614 	"bootcmd_flash2=run set_bootargs; "				\
615 		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
616 	"bootcmd=run bootcmd_flash1\0"
617 #endif	/* __CONFIG_H */
618