1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite537x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_SYS_BOARD_NAME "XPedite5370" 18 #define CONFIG_SYS_FORM_3U_VPX 1 19 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 20 21 #ifndef CONFIG_SYS_TEXT_BASE 22 #define CONFIG_SYS_TEXT_BASE 0xfff80000 23 #endif 24 25 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 26 #define CONFIG_PCIE1 1 /* PCIE controller 1 */ 27 #define CONFIG_PCIE2 1 /* PCIE controller 2 */ 28 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 29 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 30 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 31 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 32 33 /* 34 * Multicore config 35 */ 36 #define CONFIG_MP 37 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 38 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 39 40 /* 41 * DDR config 42 */ 43 #undef CONFIG_FSL_DDR_INTERACTIVE 44 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 45 #define CONFIG_DDR_SPD 46 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 47 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 48 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 49 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 50 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 51 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 52 #define CONFIG_DDR_ECC 53 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 54 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 55 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 56 #define CONFIG_VERY_BIG_RAM 57 58 #ifndef __ASSEMBLY__ 59 extern unsigned long get_board_sys_clk(unsigned long dummy); 60 extern unsigned long get_board_ddr_clk(unsigned long dummy); 61 #endif 62 63 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 64 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 65 66 /* 67 * These can be toggled for performance analysis, otherwise use default. 68 */ 69 #define CONFIG_L2_CACHE /* toggle L2 cache */ 70 #define CONFIG_BTB /* toggle branch predition */ 71 #define CONFIG_ENABLE_36BIT_PHYS 1 72 73 #define CONFIG_SYS_CCSRBAR 0xef000000 74 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 75 76 /* 77 * Diagnostics 78 */ 79 #define CONFIG_SYS_ALT_MEMTEST 80 #define CONFIG_SYS_MEMTEST_START 0x10000000 81 #define CONFIG_SYS_MEMTEST_END 0x20000000 82 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 83 CONFIG_SYS_POST_I2C) 84 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ 85 #define I2C_ADDR_IGNORE_LIST {0x50} 86 87 /* 88 * Memory map 89 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 90 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 91 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 92 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 93 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 94 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 95 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 96 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 97 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 98 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 99 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 100 */ 101 102 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 103 104 /* 105 * NAND flash configuration 106 */ 107 #define CONFIG_SYS_NAND_BASE 0xef800000 108 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 109 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 110 CONFIG_SYS_NAND_BASE2} 111 #define CONFIG_SYS_MAX_NAND_DEVICE 2 112 #define CONFIG_NAND_FSL_ELBC 113 114 /* 115 * NOR flash configuration 116 */ 117 #define CONFIG_SYS_FLASH_BASE 0xf8000000 118 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 119 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 120 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 121 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 122 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 123 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 124 #define CONFIG_FLASH_CFI_DRIVER 125 #define CONFIG_SYS_FLASH_CFI 126 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 127 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 128 {0xf7f40000, 0xc0000} } 129 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 130 131 /* 132 * Chip select configuration 133 */ 134 /* NOR Flash 0 on CS0 */ 135 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 136 BR_PS_16 | \ 137 BR_V) 138 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 139 OR_GPCM_CSNT | \ 140 OR_GPCM_XACS | \ 141 OR_GPCM_ACS_DIV2 | \ 142 OR_GPCM_SCY_8 | \ 143 OR_GPCM_TRLX | \ 144 OR_GPCM_EHTR | \ 145 OR_GPCM_EAD) 146 147 /* NOR Flash 1 on CS1 */ 148 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 149 BR_PS_16 | \ 150 BR_V) 151 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 152 153 /* NAND flash on CS2 */ 154 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 155 (2<<BR_DECC_SHIFT) | \ 156 BR_PS_8 | \ 157 BR_MS_FCM | \ 158 BR_V) 159 160 /* NAND flash on CS2 */ 161 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 162 OR_FCM_PGS | \ 163 OR_FCM_CSCT | \ 164 OR_FCM_CST | \ 165 OR_FCM_CHT | \ 166 OR_FCM_SCY_1 | \ 167 OR_FCM_TRLX | \ 168 OR_FCM_EHTR) 169 170 /* NAND flash on CS3 */ 171 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 172 (2<<BR_DECC_SHIFT) | \ 173 BR_PS_8 | \ 174 BR_MS_FCM | \ 175 BR_V) 176 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 177 178 /* 179 * Use L1 as initial stack 180 */ 181 #define CONFIG_SYS_INIT_RAM_LOCK 1 182 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 183 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 184 185 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 186 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 187 188 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 189 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 190 191 /* 192 * Serial Port 193 */ 194 #define CONFIG_CONS_INDEX 1 195 #define CONFIG_SYS_NS16550_SERIAL 196 #define CONFIG_SYS_NS16550_REG_SIZE 1 197 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 198 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 199 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 200 #define CONFIG_SYS_BAUDRATE_TABLE \ 201 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 202 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 203 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 204 205 /* 206 * I2C 207 */ 208 #define CONFIG_SYS_I2C 209 #define CONFIG_SYS_I2C_FSL 210 #define CONFIG_SYS_FSL_I2C_SPEED 400000 211 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 212 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 213 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 214 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 215 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 216 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 217 218 /* PEX8518 slave I2C interface */ 219 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 220 221 /* I2C DS1631 temperature sensor */ 222 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 223 224 /* I2C EEPROM - AT24C128B */ 225 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 226 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 227 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 228 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 229 230 /* I2C RTC */ 231 #define CONFIG_RTC_M41T11 1 232 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 233 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 234 235 /* GPIO */ 236 #define CONFIG_PCA953X 237 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 238 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 239 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 240 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 241 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 242 243 /* 244 * PU = pulled high, PD = pulled low 245 * I = input, O = output, IO = input/output 246 */ 247 /* PCA9557 @ 0x18*/ 248 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 249 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 250 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 251 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 252 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 253 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 254 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ 255 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ 256 257 /* PCA9557 @ 0x1c*/ 258 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 259 #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ 260 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 261 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 262 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 263 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 264 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 265 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 266 267 /* PCA9557 @ 0x1e*/ 268 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 269 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 270 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 271 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 272 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 273 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ 274 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ 275 276 /* PCA9557 @ 0x1f */ 277 #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ 278 #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ 279 #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ 280 #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ 281 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ 282 283 /* 284 * General PCI 285 * Memory space is mapped 1-1, but I/O space must start from 0. 286 */ 287 /* PCIE1 - VPX P1 */ 288 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 289 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 290 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 291 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 292 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 293 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 294 295 /* PCIE2 - PEX8518 */ 296 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 297 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 298 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 299 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 300 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 301 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 302 303 /* 304 * Networking options 305 */ 306 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 307 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 308 #define CONFIG_TSEC_TBI 309 #define CONFIG_MII 1 /* MII PHY management */ 310 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 311 #define CONFIG_ETHPRIME "eTSEC2" 312 313 /* 314 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 315 * 1000mbps SGMII link 316 */ 317 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 318 TBICR_PHY_RESET \ 319 | TBICR_FULL_DUPLEX \ 320 | TBICR_SPEED1_SET \ 321 ) 322 323 #define CONFIG_TSEC1 1 324 #define CONFIG_TSEC1_NAME "eTSEC1" 325 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 326 #define TSEC1_PHY_ADDR 1 327 #define TSEC1_PHYIDX 0 328 #define CONFIG_HAS_ETH0 329 330 #define CONFIG_TSEC2 1 331 #define CONFIG_TSEC2_NAME "eTSEC2" 332 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 333 #define TSEC2_PHY_ADDR 2 334 #define TSEC2_PHYIDX 0 335 #define CONFIG_HAS_ETH1 336 337 /* 338 * Command configuration. 339 */ 340 #define CONFIG_CMD_NAND 341 #define CONFIG_CMD_PCA953X 342 #define CONFIG_CMD_PCA953X_INFO 343 #define CONFIG_CMD_PCI 344 #define CONFIG_CMD_PCI_ENUM 345 #define CONFIG_CMD_REGINFO 346 347 /* 348 * Miscellaneous configurable options 349 */ 350 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 351 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 352 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 353 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 354 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 355 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 356 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 357 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 358 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 359 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 360 #define CONFIG_PREBOOT /* enable preboot variable */ 361 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 362 363 /* 364 * For booting Linux, the board info and command line data 365 * have to be in the first 16 MB of memory, since this is 366 * the maximum mapped by the Linux kernel during initialization. 367 */ 368 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 369 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 370 371 /* 372 * Environment Configuration 373 */ 374 #define CONFIG_ENV_IS_IN_FLASH 1 375 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 376 #define CONFIG_ENV_SIZE 0x8000 377 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 378 379 /* 380 * Flash memory map: 381 * fff80000 - ffffffff Pri U-Boot (512 KB) 382 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 383 * fff00000 - fff3ffff Pri FDT (256KB) 384 * fef00000 - ffefffff Pri OS image (16MB) 385 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 386 * 387 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 388 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 389 * f7f00000 - f7f3ffff Sec FDT (256KB) 390 * f6f00000 - f7efffff Sec OS image (16MB) 391 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 392 */ 393 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 394 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 395 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 396 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 397 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 398 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 399 400 #define CONFIG_PROG_UBOOT1 \ 401 "$download_cmd $loadaddr $ubootfile; " \ 402 "if test $? -eq 0; then " \ 403 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 404 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 405 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 406 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 407 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 408 "if test $? -ne 0; then " \ 409 "echo PROGRAM FAILED; " \ 410 "else; " \ 411 "echo PROGRAM SUCCEEDED; " \ 412 "fi; " \ 413 "else; " \ 414 "echo DOWNLOAD FAILED; " \ 415 "fi;" 416 417 #define CONFIG_PROG_UBOOT2 \ 418 "$download_cmd $loadaddr $ubootfile; " \ 419 "if test $? -eq 0; then " \ 420 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 421 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 422 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 423 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 424 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 425 "if test $? -ne 0; then " \ 426 "echo PROGRAM FAILED; " \ 427 "else; " \ 428 "echo PROGRAM SUCCEEDED; " \ 429 "fi; " \ 430 "else; " \ 431 "echo DOWNLOAD FAILED; " \ 432 "fi;" 433 434 #define CONFIG_BOOT_OS_NET \ 435 "$download_cmd $osaddr $osfile; " \ 436 "if test $? -eq 0; then " \ 437 "if test -n $fdtaddr; then " \ 438 "$download_cmd $fdtaddr $fdtfile; " \ 439 "if test $? -eq 0; then " \ 440 "bootm $osaddr - $fdtaddr; " \ 441 "else; " \ 442 "echo FDT DOWNLOAD FAILED; " \ 443 "fi; " \ 444 "else; " \ 445 "bootm $osaddr; " \ 446 "fi; " \ 447 "else; " \ 448 "echo OS DOWNLOAD FAILED; " \ 449 "fi;" 450 451 #define CONFIG_PROG_OS1 \ 452 "$download_cmd $osaddr $osfile; " \ 453 "if test $? -eq 0; then " \ 454 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 455 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 456 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 457 "if test $? -ne 0; then " \ 458 "echo OS PROGRAM FAILED; " \ 459 "else; " \ 460 "echo OS PROGRAM SUCCEEDED; " \ 461 "fi; " \ 462 "else; " \ 463 "echo OS DOWNLOAD FAILED; " \ 464 "fi;" 465 466 #define CONFIG_PROG_OS2 \ 467 "$download_cmd $osaddr $osfile; " \ 468 "if test $? -eq 0; then " \ 469 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 470 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 471 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 472 "if test $? -ne 0; then " \ 473 "echo OS PROGRAM FAILED; " \ 474 "else; " \ 475 "echo OS PROGRAM SUCCEEDED; " \ 476 "fi; " \ 477 "else; " \ 478 "echo OS DOWNLOAD FAILED; " \ 479 "fi;" 480 481 #define CONFIG_PROG_FDT1 \ 482 "$download_cmd $fdtaddr $fdtfile; " \ 483 "if test $? -eq 0; then " \ 484 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 485 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 486 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 487 "if test $? -ne 0; then " \ 488 "echo FDT PROGRAM FAILED; " \ 489 "else; " \ 490 "echo FDT PROGRAM SUCCEEDED; " \ 491 "fi; " \ 492 "else; " \ 493 "echo FDT DOWNLOAD FAILED; " \ 494 "fi;" 495 496 #define CONFIG_PROG_FDT2 \ 497 "$download_cmd $fdtaddr $fdtfile; " \ 498 "if test $? -eq 0; then " \ 499 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 500 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 501 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 502 "if test $? -ne 0; then " \ 503 "echo FDT PROGRAM FAILED; " \ 504 "else; " \ 505 "echo FDT PROGRAM SUCCEEDED; " \ 506 "fi; " \ 507 "else; " \ 508 "echo FDT DOWNLOAD FAILED; " \ 509 "fi;" 510 511 #define CONFIG_EXTRA_ENV_SETTINGS \ 512 "autoload=yes\0" \ 513 "download_cmd=tftp\0" \ 514 "console_args=console=ttyS0,115200\0" \ 515 "root_args=root=/dev/nfs rw\0" \ 516 "misc_args=ip=on\0" \ 517 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 518 "bootfile=/home/user/file\0" \ 519 "osfile=/home/user/board.uImage\0" \ 520 "fdtfile=/home/user/board.dtb\0" \ 521 "ubootfile=/home/user/u-boot.bin\0" \ 522 "fdtaddr=0x1e00000\0" \ 523 "osaddr=0x1000000\0" \ 524 "loadaddr=0x1000000\0" \ 525 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 526 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 527 "prog_os1="CONFIG_PROG_OS1"\0" \ 528 "prog_os2="CONFIG_PROG_OS2"\0" \ 529 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 530 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 531 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 532 "bootcmd_flash1=run set_bootargs; " \ 533 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 534 "bootcmd_flash2=run set_bootargs; " \ 535 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 536 "bootcmd=run bootcmd_flash1\0" 537 #endif /* __CONFIG_H */ 538