1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite537x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_BOOKE 1 /* BOOKE */ 18 #define CONFIG_E500 1 /* BOOKE e500 family */ 19 #define CONFIG_SYS_BOARD_NAME "XPedite5370" 20 #define CONFIG_SYS_FORM_3U_VPX 1 21 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 22 23 #ifndef CONFIG_SYS_TEXT_BASE 24 #define CONFIG_SYS_TEXT_BASE 0xfff80000 25 #endif 26 27 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 28 #define CONFIG_PCIE1 1 /* PCIE controller 1 */ 29 #define CONFIG_PCIE2 1 /* PCIE controller 2 */ 30 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 31 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 32 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 33 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 34 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 35 #define CONFIG_FSL_ELBC 1 36 37 /* 38 * Multicore config 39 */ 40 #define CONFIG_MP 41 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 42 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 43 44 /* 45 * DDR config 46 */ 47 #define CONFIG_SYS_FSL_DDR2 48 #undef CONFIG_FSL_DDR_INTERACTIVE 49 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 50 #define CONFIG_DDR_SPD 51 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 52 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 53 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 54 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 55 #define CONFIG_NUM_DDR_CONTROLLERS 2 56 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 57 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 58 #define CONFIG_DDR_ECC 59 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 60 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 61 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 62 #define CONFIG_VERY_BIG_RAM 63 64 #ifndef __ASSEMBLY__ 65 extern unsigned long get_board_sys_clk(unsigned long dummy); 66 extern unsigned long get_board_ddr_clk(unsigned long dummy); 67 #endif 68 69 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 70 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 71 72 /* 73 * These can be toggled for performance analysis, otherwise use default. 74 */ 75 #define CONFIG_L2_CACHE /* toggle L2 cache */ 76 #define CONFIG_BTB /* toggle branch predition */ 77 #define CONFIG_ENABLE_36BIT_PHYS 1 78 79 #define CONFIG_SYS_CCSRBAR 0xef000000 80 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 81 82 /* 83 * Diagnostics 84 */ 85 #define CONFIG_SYS_ALT_MEMTEST 86 #define CONFIG_SYS_MEMTEST_START 0x10000000 87 #define CONFIG_SYS_MEMTEST_END 0x20000000 88 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 89 CONFIG_SYS_POST_I2C) 90 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ 91 CONFIG_SYS_I2C_DS4510_ADDR, \ 92 CONFIG_SYS_I2C_EEPROM_ADDR, \ 93 CONFIG_SYS_I2C_LM90_ADDR, \ 94 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 95 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 96 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 97 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 98 CONFIG_SYS_I2C_PEX8518_ADDR, \ 99 CONFIG_SYS_I2C_RTC_ADDR} 100 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ 101 #define I2C_ADDR_IGNORE_LIST {0x50} 102 103 /* 104 * Memory map 105 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 106 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 107 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 108 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 109 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 110 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 111 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 112 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 113 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 114 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 115 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 116 */ 117 118 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 119 120 /* 121 * NAND flash configuration 122 */ 123 #define CONFIG_SYS_NAND_BASE 0xef800000 124 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 125 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 126 CONFIG_SYS_NAND_BASE2} 127 #define CONFIG_SYS_MAX_NAND_DEVICE 2 128 #define CONFIG_NAND_FSL_ELBC 129 130 /* 131 * NOR flash configuration 132 */ 133 #define CONFIG_SYS_FLASH_BASE 0xf8000000 134 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 135 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 136 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 137 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 138 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 139 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 140 #define CONFIG_FLASH_CFI_DRIVER 141 #define CONFIG_SYS_FLASH_CFI 142 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 143 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 144 {0xf7f40000, 0xc0000} } 145 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 146 147 /* 148 * Chip select configuration 149 */ 150 /* NOR Flash 0 on CS0 */ 151 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 152 BR_PS_16 | \ 153 BR_V) 154 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 155 OR_GPCM_CSNT | \ 156 OR_GPCM_XACS | \ 157 OR_GPCM_ACS_DIV2 | \ 158 OR_GPCM_SCY_8 | \ 159 OR_GPCM_TRLX | \ 160 OR_GPCM_EHTR | \ 161 OR_GPCM_EAD) 162 163 /* NOR Flash 1 on CS1 */ 164 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 165 BR_PS_16 | \ 166 BR_V) 167 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 168 169 /* NAND flash on CS2 */ 170 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 171 (2<<BR_DECC_SHIFT) | \ 172 BR_PS_8 | \ 173 BR_MS_FCM | \ 174 BR_V) 175 176 /* NAND flash on CS2 */ 177 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 178 OR_FCM_PGS | \ 179 OR_FCM_CSCT | \ 180 OR_FCM_CST | \ 181 OR_FCM_CHT | \ 182 OR_FCM_SCY_1 | \ 183 OR_FCM_TRLX | \ 184 OR_FCM_EHTR) 185 186 /* NAND flash on CS3 */ 187 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 188 (2<<BR_DECC_SHIFT) | \ 189 BR_PS_8 | \ 190 BR_MS_FCM | \ 191 BR_V) 192 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 193 194 /* 195 * Use L1 as initial stack 196 */ 197 #define CONFIG_SYS_INIT_RAM_LOCK 1 198 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 199 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 200 201 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 202 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 203 204 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 205 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 206 207 /* 208 * Serial Port 209 */ 210 #define CONFIG_CONS_INDEX 1 211 #define CONFIG_SYS_NS16550_SERIAL 212 #define CONFIG_SYS_NS16550_REG_SIZE 1 213 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 214 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 215 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 216 #define CONFIG_SYS_BAUDRATE_TABLE \ 217 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 218 #define CONFIG_BAUDRATE 115200 219 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 220 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 221 222 /* 223 * I2C 224 */ 225 #define CONFIG_SYS_I2C 226 #define CONFIG_SYS_I2C_FSL 227 #define CONFIG_SYS_FSL_I2C_SPEED 400000 228 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 229 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 230 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 231 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 232 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 233 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 234 235 /* PEX8518 slave I2C interface */ 236 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 237 238 /* I2C DS1631 temperature sensor */ 239 #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 240 #define CONFIG_DTT_DS1621 241 #define CONFIG_DTT_SENSORS { 0 } 242 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 243 244 /* I2C EEPROM - AT24C128B */ 245 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 246 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 247 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 248 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 249 250 /* I2C RTC */ 251 #define CONFIG_RTC_M41T11 1 252 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 253 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 254 255 /* GPIO/EEPROM/SRAM */ 256 #define CONFIG_DS4510 257 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 258 259 /* GPIO */ 260 #define CONFIG_PCA953X 261 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 262 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 263 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 264 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 265 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 266 267 /* 268 * PU = pulled high, PD = pulled low 269 * I = input, O = output, IO = input/output 270 */ 271 /* PCA9557 @ 0x18*/ 272 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 273 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 274 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 275 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 276 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 277 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 278 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ 279 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ 280 281 /* PCA9557 @ 0x1c*/ 282 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 283 #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ 284 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 285 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 286 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 287 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 288 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 289 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 290 291 /* PCA9557 @ 0x1e*/ 292 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 293 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 294 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 295 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 296 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 297 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ 298 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ 299 300 /* PCA9557 @ 0x1f */ 301 #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ 302 #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ 303 #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ 304 #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ 305 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ 306 307 /* 308 * General PCI 309 * Memory space is mapped 1-1, but I/O space must start from 0. 310 */ 311 /* PCIE1 - VPX P1 */ 312 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 313 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 314 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 315 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 316 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 317 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 318 319 /* PCIE2 - PEX8518 */ 320 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 321 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 322 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 323 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 324 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 325 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 326 327 /* 328 * Networking options 329 */ 330 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 331 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 332 #define CONFIG_TSEC_TBI 333 #define CONFIG_MII 1 /* MII PHY management */ 334 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 335 #define CONFIG_ETHPRIME "eTSEC2" 336 337 /* 338 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 339 * 1000mbps SGMII link 340 */ 341 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 342 TBICR_PHY_RESET \ 343 | TBICR_FULL_DUPLEX \ 344 | TBICR_SPEED1_SET \ 345 ) 346 347 #define CONFIG_TSEC1 1 348 #define CONFIG_TSEC1_NAME "eTSEC1" 349 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 350 #define TSEC1_PHY_ADDR 1 351 #define TSEC1_PHYIDX 0 352 #define CONFIG_HAS_ETH0 353 354 #define CONFIG_TSEC2 1 355 #define CONFIG_TSEC2_NAME "eTSEC2" 356 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 357 #define TSEC2_PHY_ADDR 2 358 #define TSEC2_PHYIDX 0 359 #define CONFIG_HAS_ETH1 360 361 /* 362 * Command configuration. 363 */ 364 #define CONFIG_CMD_DATE 365 #define CONFIG_CMD_DS4510 366 #define CONFIG_CMD_DS4510_INFO 367 #define CONFIG_CMD_DTT 368 #define CONFIG_CMD_EEPROM 369 #define CONFIG_CMD_JFFS2 370 #define CONFIG_CMD_NAND 371 #define CONFIG_CMD_PCA953X 372 #define CONFIG_CMD_PCA953X_INFO 373 #define CONFIG_CMD_PCI 374 #define CONFIG_CMD_PCI_ENUM 375 #define CONFIG_CMD_REGINFO 376 377 /* 378 * Miscellaneous configurable options 379 */ 380 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 381 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 382 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 383 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 384 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 385 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 386 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 387 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 388 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 389 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 390 #define CONFIG_PREBOOT /* enable preboot variable */ 391 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 392 393 /* 394 * For booting Linux, the board info and command line data 395 * have to be in the first 16 MB of memory, since this is 396 * the maximum mapped by the Linux kernel during initialization. 397 */ 398 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 399 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 400 401 /* 402 * Environment Configuration 403 */ 404 #define CONFIG_ENV_IS_IN_FLASH 1 405 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 406 #define CONFIG_ENV_SIZE 0x8000 407 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 408 409 /* 410 * Flash memory map: 411 * fff80000 - ffffffff Pri U-Boot (512 KB) 412 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 413 * fff00000 - fff3ffff Pri FDT (256KB) 414 * fef00000 - ffefffff Pri OS image (16MB) 415 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 416 * 417 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 418 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 419 * f7f00000 - f7f3ffff Sec FDT (256KB) 420 * f6f00000 - f7efffff Sec OS image (16MB) 421 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 422 */ 423 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 424 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 425 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 426 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 427 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 428 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 429 430 #define CONFIG_PROG_UBOOT1 \ 431 "$download_cmd $loadaddr $ubootfile; " \ 432 "if test $? -eq 0; then " \ 433 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 434 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 435 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 436 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 437 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 438 "if test $? -ne 0; then " \ 439 "echo PROGRAM FAILED; " \ 440 "else; " \ 441 "echo PROGRAM SUCCEEDED; " \ 442 "fi; " \ 443 "else; " \ 444 "echo DOWNLOAD FAILED; " \ 445 "fi;" 446 447 #define CONFIG_PROG_UBOOT2 \ 448 "$download_cmd $loadaddr $ubootfile; " \ 449 "if test $? -eq 0; then " \ 450 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 451 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 452 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 453 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 454 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 455 "if test $? -ne 0; then " \ 456 "echo PROGRAM FAILED; " \ 457 "else; " \ 458 "echo PROGRAM SUCCEEDED; " \ 459 "fi; " \ 460 "else; " \ 461 "echo DOWNLOAD FAILED; " \ 462 "fi;" 463 464 #define CONFIG_BOOT_OS_NET \ 465 "$download_cmd $osaddr $osfile; " \ 466 "if test $? -eq 0; then " \ 467 "if test -n $fdtaddr; then " \ 468 "$download_cmd $fdtaddr $fdtfile; " \ 469 "if test $? -eq 0; then " \ 470 "bootm $osaddr - $fdtaddr; " \ 471 "else; " \ 472 "echo FDT DOWNLOAD FAILED; " \ 473 "fi; " \ 474 "else; " \ 475 "bootm $osaddr; " \ 476 "fi; " \ 477 "else; " \ 478 "echo OS DOWNLOAD FAILED; " \ 479 "fi;" 480 481 #define CONFIG_PROG_OS1 \ 482 "$download_cmd $osaddr $osfile; " \ 483 "if test $? -eq 0; then " \ 484 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 485 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 486 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 487 "if test $? -ne 0; then " \ 488 "echo OS PROGRAM FAILED; " \ 489 "else; " \ 490 "echo OS PROGRAM SUCCEEDED; " \ 491 "fi; " \ 492 "else; " \ 493 "echo OS DOWNLOAD FAILED; " \ 494 "fi;" 495 496 #define CONFIG_PROG_OS2 \ 497 "$download_cmd $osaddr $osfile; " \ 498 "if test $? -eq 0; then " \ 499 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 500 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 501 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 502 "if test $? -ne 0; then " \ 503 "echo OS PROGRAM FAILED; " \ 504 "else; " \ 505 "echo OS PROGRAM SUCCEEDED; " \ 506 "fi; " \ 507 "else; " \ 508 "echo OS DOWNLOAD FAILED; " \ 509 "fi;" 510 511 #define CONFIG_PROG_FDT1 \ 512 "$download_cmd $fdtaddr $fdtfile; " \ 513 "if test $? -eq 0; then " \ 514 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 515 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 516 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 517 "if test $? -ne 0; then " \ 518 "echo FDT PROGRAM FAILED; " \ 519 "else; " \ 520 "echo FDT PROGRAM SUCCEEDED; " \ 521 "fi; " \ 522 "else; " \ 523 "echo FDT DOWNLOAD FAILED; " \ 524 "fi;" 525 526 #define CONFIG_PROG_FDT2 \ 527 "$download_cmd $fdtaddr $fdtfile; " \ 528 "if test $? -eq 0; then " \ 529 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 530 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 531 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 532 "if test $? -ne 0; then " \ 533 "echo FDT PROGRAM FAILED; " \ 534 "else; " \ 535 "echo FDT PROGRAM SUCCEEDED; " \ 536 "fi; " \ 537 "else; " \ 538 "echo FDT DOWNLOAD FAILED; " \ 539 "fi;" 540 541 #define CONFIG_EXTRA_ENV_SETTINGS \ 542 "autoload=yes\0" \ 543 "download_cmd=tftp\0" \ 544 "console_args=console=ttyS0,115200\0" \ 545 "root_args=root=/dev/nfs rw\0" \ 546 "misc_args=ip=on\0" \ 547 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 548 "bootfile=/home/user/file\0" \ 549 "osfile=/home/user/board.uImage\0" \ 550 "fdtfile=/home/user/board.dtb\0" \ 551 "ubootfile=/home/user/u-boot.bin\0" \ 552 "fdtaddr=0x1e00000\0" \ 553 "osaddr=0x1000000\0" \ 554 "loadaddr=0x1000000\0" \ 555 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 556 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 557 "prog_os1="CONFIG_PROG_OS1"\0" \ 558 "prog_os2="CONFIG_PROG_OS2"\0" \ 559 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 560 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 561 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 562 "bootcmd_flash1=run set_bootargs; " \ 563 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 564 "bootcmd_flash2=run set_bootargs; " \ 565 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 566 "bootcmd=run bootcmd_flash1\0" 567 #endif /* __CONFIG_H */ 568