1 /*
2  * Copyright 2008 Extreme Engineering Solutions, Inc.
3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 /*
9  * xpedite537x board configuration file
10  */
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /*
15  * High Level Configuration Options
16  */
17 #define CONFIG_BOOKE		1	/* BOOKE */
18 #define CONFIG_E500		1	/* BOOKE e500 family */
19 #define CONFIG_MPC8572		1
20 #define CONFIG_XPEDITE5370	1
21 #define CONFIG_SYS_BOARD_NAME	"XPedite5370"
22 #define CONFIG_SYS_FORM_3U_VPX	1
23 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
24 #define CONFIG_SYS_GENERIC_BOARD
25 #define CONFIG_DISPLAY_BOARDINFO
26 
27 #ifndef CONFIG_SYS_TEXT_BASE
28 #define CONFIG_SYS_TEXT_BASE	0xfff80000
29 #endif
30 
31 #define CONFIG_PCI		1	/* Enable PCI/PCIE */
32 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play */
33 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
34 #define CONFIG_PCIE1		1	/* PCIE controler 1 */
35 #define CONFIG_PCIE2		1	/* PCIE controler 2 */
36 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
37 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
38 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
39 #define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
40 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
41 #define CONFIG_FSL_ELBC		1
42 
43 /*
44  * Multicore config
45  */
46 #define CONFIG_MP
47 #define CONFIG_BPTR_VIRT_ADDR	0xee000000	/* virt boot page address */
48 #define CONFIG_MPC8xxx_DISABLE_BPTR		/* Don't leave BPTR enabled */
49 
50 /*
51  * DDR config
52  */
53 #define CONFIG_SYS_FSL_DDR2
54 #undef CONFIG_FSL_DDR_INTERACTIVE
55 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
56 #define CONFIG_DDR_SPD
57 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
58 #define SPD_EEPROM_ADDRESS1		0x54	/* Both channels use the */
59 #define SPD_EEPROM_ADDRESS2		0x54	/* same SPD data         */
60 #define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
61 #define CONFIG_NUM_DDR_CONTROLLERS	2
62 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
63 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
64 #define CONFIG_DDR_ECC
65 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
66 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000 /* DDR is system memory*/
67 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
68 #define CONFIG_VERY_BIG_RAM
69 
70 #ifndef __ASSEMBLY__
71 extern unsigned long get_board_sys_clk(unsigned long dummy);
72 extern unsigned long get_board_ddr_clk(unsigned long dummy);
73 #endif
74 
75 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
76 #define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */
77 
78 /*
79  * These can be toggled for performance analysis, otherwise use default.
80  */
81 #define CONFIG_L2_CACHE			/* toggle L2 cache */
82 #define CONFIG_BTB			/* toggle branch predition */
83 #define CONFIG_ENABLE_36BIT_PHYS	1
84 
85 #define CONFIG_SYS_CCSRBAR		0xef000000
86 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
87 
88 /*
89  * Diagnostics
90  */
91 #define CONFIG_SYS_ALT_MEMTEST
92 #define CONFIG_SYS_MEMTEST_START	0x10000000
93 #define CONFIG_SYS_MEMTEST_END		0x20000000
94 #define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
95 					 CONFIG_SYS_POST_I2C)
96 #define I2C_ADDR_LIST			{CONFIG_SYS_I2C_DS1621_ADDR,	\
97 					 CONFIG_SYS_I2C_DS4510_ADDR,	\
98 					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
99 					 CONFIG_SYS_I2C_LM90_ADDR,	\
100 					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
101 					 CONFIG_SYS_I2C_PCA953X_ADDR1,	\
102 					 CONFIG_SYS_I2C_PCA953X_ADDR2,	\
103 					 CONFIG_SYS_I2C_PCA953X_ADDR3,	\
104 					 CONFIG_SYS_I2C_PEX8518_ADDR,	\
105 					 CONFIG_SYS_I2C_RTC_ADDR}
106 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
107 #define I2C_ADDR_IGNORE_LIST		{0x50}
108 
109 /*
110  * Memory map
111  * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
112  * 0x8000_0000	0xbfff_ffff	PCIe1 Mem		1G non-cacheable
113  * 0xc000_0000	0xcfff_ffff	PCIe2 Mem		256M non-cacheable
114  * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
115  * 0xe800_0000	0xe87f_ffff	PCIe1 IO		8M non-cacheable
116  * 0xe880_0000	0xe8ff_ffff	PCIe2 IO		8M non-cacheable
117  * 0xee00_0000	0xee00_ffff	Boot page translation	4K non-cacheable
118  * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
119  * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
120  * 0xf000_0000	0xf7ff_ffff	NOR Flash 2		128M non-cacheable
121  * 0xf800_0000	0xffff_ffff	NOR Flash 1		128M non-cacheable
122  */
123 
124 #define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)
125 
126 /*
127  * NAND flash configuration
128  */
129 #define CONFIG_SYS_NAND_BASE		0xef800000
130 #define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
131 #define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE, \
132 					 CONFIG_SYS_NAND_BASE2}
133 #define CONFIG_SYS_MAX_NAND_DEVICE	2
134 #define CONFIG_SYS_NAND_QUIET_TEST	/* 2nd NAND flash not always populated */
135 #define CONFIG_NAND_FSL_ELBC
136 
137 /*
138  * NOR flash configuration
139  */
140 #define CONFIG_SYS_FLASH_BASE		0xf8000000
141 #define CONFIG_SYS_FLASH_BASE2		0xf0000000
142 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
143 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
144 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
145 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
146 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
147 #define CONFIG_FLASH_CFI_DRIVER
148 #define CONFIG_SYS_FLASH_CFI
149 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
150 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
151 						  {0xf7f40000, 0xc0000} }
152 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
153 
154 /*
155  * Chip select configuration
156  */
157 /* NOR Flash 0 on CS0 */
158 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
159 				 BR_PS_16		| \
160 				 BR_V)
161 #define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		| \
162 				 OR_GPCM_CSNT		| \
163 				 OR_GPCM_XACS		| \
164 				 OR_GPCM_ACS_DIV2	| \
165 				 OR_GPCM_SCY_8		| \
166 				 OR_GPCM_TRLX		| \
167 				 OR_GPCM_EHTR		| \
168 				 OR_GPCM_EAD)
169 
170 /* NOR Flash 1 on CS1 */
171 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
172 				 BR_PS_16		| \
173 				 BR_V)
174 #define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
175 
176 /* NAND flash on CS2 */
177 #define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
178 				 (2<<BR_DECC_SHIFT)	| \
179 				 BR_PS_8		| \
180 				 BR_MS_FCM		| \
181 				 BR_V)
182 
183 /* NAND flash on CS2 */
184 #define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB	| \
185 				 OR_FCM_PGS	| \
186 				 OR_FCM_CSCT	| \
187 				 OR_FCM_CST	| \
188 				 OR_FCM_CHT	| \
189 				 OR_FCM_SCY_1	| \
190 				 OR_FCM_TRLX	| \
191 				 OR_FCM_EHTR)
192 
193 /* NAND flash on CS3 */
194 #define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
195 				 (2<<BR_DECC_SHIFT)	| \
196 				 BR_PS_8		| \
197 				 BR_MS_FCM		| \
198 				 BR_V)
199 #define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
200 
201 /*
202  * Use L1 as initial stack
203  */
204 #define CONFIG_SYS_INIT_RAM_LOCK	1
205 #define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
206 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
207 
208 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
209 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
210 
211 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
212 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
213 
214 /*
215  * Serial Port
216  */
217 #define CONFIG_CONS_INDEX		1
218 #define CONFIG_SYS_NS16550
219 #define CONFIG_SYS_NS16550_SERIAL
220 #define CONFIG_SYS_NS16550_REG_SIZE	1
221 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
222 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
223 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
224 #define CONFIG_SYS_BAUDRATE_TABLE	\
225 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
226 #define CONFIG_BAUDRATE			115200
227 #define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
228 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
229 
230 /*
231  * Use the HUSH parser
232  */
233 #define CONFIG_SYS_HUSH_PARSER
234 
235 /*
236  * Pass open firmware flat tree
237  */
238 #define CONFIG_OF_LIBFDT		1
239 #define CONFIG_OF_BOARD_SETUP		1
240 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
241 
242 /*
243  * I2C
244  */
245 #define CONFIG_SYS_I2C
246 #define CONFIG_SYS_I2C_FSL
247 #define CONFIG_SYS_FSL_I2C_SPEED	400000
248 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
249 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
250 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
251 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
252 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
253 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
254 
255 /* PEX8518 slave I2C interface */
256 #define CONFIG_SYS_I2C_PEX8518_ADDR	0x70
257 
258 /* I2C DS1631 temperature sensor */
259 #define CONFIG_SYS_I2C_DS1621_ADDR	0x48
260 #define CONFIG_DTT_DS1621
261 #define CONFIG_DTT_SENSORS		{ 0 }
262 #define CONFIG_SYS_I2C_LM90_ADDR	0x4c
263 
264 /* I2C EEPROM - AT24C128B */
265 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
266 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
267 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
268 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
269 
270 /* I2C RTC */
271 #define CONFIG_RTC_M41T11		1
272 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
273 #define CONFIG_SYS_M41T11_BASE_YEAR	2000
274 
275 /* GPIO/EEPROM/SRAM */
276 #define CONFIG_DS4510
277 #define CONFIG_SYS_I2C_DS4510_ADDR	0x51
278 
279 /* GPIO */
280 #define CONFIG_PCA953X
281 #define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
282 #define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
283 #define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
284 #define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
285 #define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
286 
287 /*
288  * PU = pulled high, PD = pulled low
289  * I = input, O = output, IO = input/output
290  */
291 /* PCA9557 @ 0x18*/
292 #define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
293 #define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select */
294 #define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
295 #define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select */
296 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
297 #define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Set to 0 to enable NVM writing */
298 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2	0x40 /* VID2 of ISL6262 */
299 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3	0x80 /* VID3 of ISL6262 */
300 
301 /* PCA9557 @ 0x1c*/
302 #define CONFIG_SYS_PCA953X_XMC0_ROOT0		0x01 /* PU; Low if XMC is RC */
303 #define CONFIG_SYS_PCA953X_XMC0_MVMR0		0x02 /* XMC EEPROM write protect */
304 #define CONFIG_SYS_PCA953X_XMC0_WAKE		0x04 /* PU; XMC wake */
305 #define CONFIG_SYS_PCA953X_XMC0_BIST		0x08 /* PU; XMC built in self test */
306 #define CONFIG_SYS_PCA953X_XMC_PRESENT		0x10 /* PU; Low if XMC module installed */
307 #define CONFIG_SYS_PCA953X_PMC_PRESENT		0x20 /* PU; Low if PMC module installed */
308 #define CONFIG_SYS_PCA953X_PMC0_MONARCH		0x40 /* PMC monarch mode enable */
309 #define CONFIG_SYS_PCA953X_PMC0_EREADY		0x80 /* PU; PMC PCI eready */
310 
311 /* PCA9557 @ 0x1e*/
312 #define CONFIG_SYS_PCA953X_P0_GA0		0x01 /* PU; VPX Geographical address */
313 #define CONFIG_SYS_PCA953X_P0_GA1		0x02 /* PU; VPX Geographical address */
314 #define CONFIG_SYS_PCA953X_P0_GA2		0x04 /* PU; VPX Geographical address */
315 #define CONFIG_SYS_PCA953X_P0_GA3		0x08 /* PU; VPX Geographical address */
316 #define CONFIG_SYS_PCA953X_P0_GA4		0x10 /* PU; VPX Geographical address */
317 #define CONFIG_SYS_PCA953X_P0_GAP		0x20 /* PU; tied to VPX P0.GAP */
318 #define CONFIG_SYS_PCA953X_P1_SYSEN		0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
319 
320 /* PCA9557 @ 0x1f */
321 #define CONFIG_SYS_PCA953X_GPIO_VPX0		0x01 /* PU */
322 #define CONFIG_SYS_PCA953X_GPIO_VPX1		0x02 /* PU */
323 #define CONFIG_SYS_PCA953X_GPIO_VPX2		0x04 /* PU */
324 #define CONFIG_SYS_PCA953X_GPIO_VPX3		0x08 /* PU */
325 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL	0x10 /* PD; I2C master source for FRU SEEPROM */
326 
327 /*
328  * General PCI
329  * Memory space is mapped 1-1, but I/O space must start from 0.
330  */
331 /* PCIE1 - VPX P1 */
332 #define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
333 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
334 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
335 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
336 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
337 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
338 
339 /* PCIE2 - PEX8518 */
340 #define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
341 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
342 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
343 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
344 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
345 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
346 
347 /*
348  * Networking options
349  */
350 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
351 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
352 #define CONFIG_TSEC_TBI
353 #define CONFIG_MII		1	/* MII PHY management */
354 #define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
355 #define CONFIG_ETHPRIME		"eTSEC2"
356 
357 /*
358  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
359  * 1000mbps SGMII link
360  */
361 #define CONFIG_TSEC_TBICR_SETTINGS ( \
362 		TBICR_PHY_RESET \
363 		| TBICR_FULL_DUPLEX \
364 		| TBICR_SPEED1_SET \
365 		)
366 
367 #define CONFIG_TSEC1		1
368 #define CONFIG_TSEC1_NAME	"eTSEC1"
369 #define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
370 #define TSEC1_PHY_ADDR		1
371 #define TSEC1_PHYIDX		0
372 #define CONFIG_HAS_ETH0
373 
374 #define CONFIG_TSEC2		1
375 #define CONFIG_TSEC2_NAME	"eTSEC2"
376 #define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
377 #define TSEC2_PHY_ADDR		2
378 #define TSEC2_PHYIDX		0
379 #define CONFIG_HAS_ETH1
380 
381 /*
382  * Command configuration.
383  */
384 #include <config_cmd_default.h>
385 
386 #define CONFIG_CMD_ASKENV
387 #define CONFIG_CMD_DATE
388 #define CONFIG_CMD_DHCP
389 #define CONFIG_CMD_DS4510
390 #define CONFIG_CMD_DS4510_INFO
391 #define CONFIG_CMD_DTT
392 #define CONFIG_CMD_EEPROM
393 #define CONFIG_CMD_ELF
394 #define CONFIG_CMD_FLASH
395 #define CONFIG_CMD_I2C
396 #define CONFIG_CMD_JFFS2
397 #define CONFIG_CMD_MII
398 #define CONFIG_CMD_NAND
399 #define CONFIG_CMD_NET
400 #define CONFIG_CMD_PCA953X
401 #define CONFIG_CMD_PCA953X_INFO
402 #define CONFIG_CMD_PCI
403 #define CONFIG_CMD_PCI_ENUM
404 #define CONFIG_CMD_PING
405 #define CONFIG_CMD_SAVEENV
406 #define CONFIG_CMD_SNTP
407 #define CONFIG_CMD_REGINFO
408 
409 /*
410  * Miscellaneous configurable options
411  */
412 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
413 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
414 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
415 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
416 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
417 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
418 #define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
419 #define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
420 #define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
421 #define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
422 #define CONFIG_PANIC_HANG			/* do not reset board on panic */
423 #define CONFIG_PREBOOT				/* enable preboot variable */
424 #define CONFIG_FIT		1
425 #define CONFIG_FIT_VERBOSE	1
426 #define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
427 
428 /*
429  * For booting Linux, the board info and command line data
430  * have to be in the first 16 MB of memory, since this is
431  * the maximum mapped by the Linux kernel during initialization.
432  */
433 #define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
434 #define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
435 
436 /*
437  * Environment Configuration
438  */
439 #define CONFIG_ENV_IS_IN_FLASH	1
440 #define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
441 #define CONFIG_ENV_SIZE		0x8000
442 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
443 
444 /*
445  * Flash memory map:
446  * fff80000 - ffffffff     Pri U-Boot (512 KB)
447  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
448  * fff00000 - fff3ffff     Pri FDT (256KB)
449  * fef00000 - ffefffff     Pri OS image (16MB)
450  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
451  *
452  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
453  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
454  * f7f00000 - f7f3ffff     Sec FDT (256KB)
455  * f6f00000 - f7efffff     Sec OS image (16MB)
456  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
457  */
458 #define CONFIG_UBOOT1_ENV_ADDR	__stringify(0xfff80000)
459 #define CONFIG_UBOOT2_ENV_ADDR	__stringify(0xf7f80000)
460 #define CONFIG_FDT1_ENV_ADDR	__stringify(0xfff00000)
461 #define CONFIG_FDT2_ENV_ADDR	__stringify(0xf7f00000)
462 #define CONFIG_OS1_ENV_ADDR	__stringify(0xfef00000)
463 #define CONFIG_OS2_ENV_ADDR	__stringify(0xf6f00000)
464 
465 #define CONFIG_PROG_UBOOT1						\
466 	"$download_cmd $loadaddr $ubootfile; "				\
467 	"if test $? -eq 0; then "					\
468 		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
469 		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
470 		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
471 		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
472 		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
473 		"if test $? -ne 0; then "				\
474 			"echo PROGRAM FAILED; "				\
475 		"else; "						\
476 			"echo PROGRAM SUCCEEDED; "			\
477 		"fi; "							\
478 	"else; "							\
479 		"echo DOWNLOAD FAILED; "				\
480 	"fi;"
481 
482 #define CONFIG_PROG_UBOOT2						\
483 	"$download_cmd $loadaddr $ubootfile; "				\
484 	"if test $? -eq 0; then "					\
485 		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
486 		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
487 		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
488 		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
489 		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
490 		"if test $? -ne 0; then "				\
491 			"echo PROGRAM FAILED; "				\
492 		"else; "						\
493 			"echo PROGRAM SUCCEEDED; "			\
494 		"fi; "							\
495 	"else; "							\
496 		"echo DOWNLOAD FAILED; "				\
497 	"fi;"
498 
499 #define CONFIG_BOOT_OS_NET						\
500 	"$download_cmd $osaddr $osfile; "				\
501 	"if test $? -eq 0; then "					\
502 		"if test -n $fdtaddr; then "				\
503 			"$download_cmd $fdtaddr $fdtfile; "		\
504 			"if test $? -eq 0; then "			\
505 				"bootm $osaddr - $fdtaddr; "		\
506 			"else; "					\
507 				"echo FDT DOWNLOAD FAILED; "		\
508 			"fi; "						\
509 		"else; "						\
510 			"bootm $osaddr; "				\
511 		"fi; "							\
512 	"else; "							\
513 		"echo OS DOWNLOAD FAILED; "				\
514 	"fi;"
515 
516 #define CONFIG_PROG_OS1							\
517 	"$download_cmd $osaddr $osfile; "				\
518 	"if test $? -eq 0; then "					\
519 		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
520 		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
521 		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
522 		"if test $? -ne 0; then "				\
523 			"echo OS PROGRAM FAILED; "			\
524 		"else; "						\
525 			"echo OS PROGRAM SUCCEEDED; "			\
526 		"fi; "							\
527 	"else; "							\
528 		"echo OS DOWNLOAD FAILED; "				\
529 	"fi;"
530 
531 #define CONFIG_PROG_OS2							\
532 	"$download_cmd $osaddr $osfile; "				\
533 	"if test $? -eq 0; then "					\
534 		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
535 		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
536 		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
537 		"if test $? -ne 0; then "				\
538 			"echo OS PROGRAM FAILED; "			\
539 		"else; "						\
540 			"echo OS PROGRAM SUCCEEDED; "			\
541 		"fi; "							\
542 	"else; "							\
543 		"echo OS DOWNLOAD FAILED; "				\
544 	"fi;"
545 
546 #define CONFIG_PROG_FDT1						\
547 	"$download_cmd $fdtaddr $fdtfile; "				\
548 	"if test $? -eq 0; then "					\
549 		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
550 		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
551 		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
552 		"if test $? -ne 0; then "				\
553 			"echo FDT PROGRAM FAILED; "			\
554 		"else; "						\
555 			"echo FDT PROGRAM SUCCEEDED; "			\
556 		"fi; "							\
557 	"else; "							\
558 		"echo FDT DOWNLOAD FAILED; "				\
559 	"fi;"
560 
561 #define CONFIG_PROG_FDT2						\
562 	"$download_cmd $fdtaddr $fdtfile; "				\
563 	"if test $? -eq 0; then "					\
564 		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
565 		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
566 		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
567 		"if test $? -ne 0; then "				\
568 			"echo FDT PROGRAM FAILED; "			\
569 		"else; "						\
570 			"echo FDT PROGRAM SUCCEEDED; "			\
571 		"fi; "							\
572 	"else; "							\
573 		"echo FDT DOWNLOAD FAILED; "				\
574 	"fi;"
575 
576 #define	CONFIG_EXTRA_ENV_SETTINGS					\
577 	"autoload=yes\0"						\
578 	"download_cmd=tftp\0"						\
579 	"console_args=console=ttyS0,115200\0"				\
580 	"root_args=root=/dev/nfs rw\0"					\
581 	"misc_args=ip=on\0"						\
582 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
583 	"bootfile=/home/user/file\0"					\
584 	"osfile=/home/user/board.uImage\0"				\
585 	"fdtfile=/home/user/board.dtb\0"				\
586 	"ubootfile=/home/user/u-boot.bin\0"				\
587 	"fdtaddr=c00000\0"						\
588 	"osaddr=0x1000000\0"						\
589 	"loadaddr=0x1000000\0"						\
590 	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
591 	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
592 	"prog_os1="CONFIG_PROG_OS1"\0"					\
593 	"prog_os2="CONFIG_PROG_OS2"\0"					\
594 	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
595 	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
596 	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
597 	"bootcmd_flash1=run set_bootargs; "				\
598 		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
599 	"bootcmd_flash2=run set_bootargs; "				\
600 		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
601 	"bootcmd=run bootcmd_flash1\0"
602 #endif	/* __CONFIG_H */
603