1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite537x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_BOOKE 1 /* BOOKE */ 18 #define CONFIG_E500 1 /* BOOKE e500 family */ 19 #define CONFIG_SYS_BOARD_NAME "XPedite5370" 20 #define CONFIG_SYS_FORM_3U_VPX 1 21 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 22 23 #ifndef CONFIG_SYS_TEXT_BASE 24 #define CONFIG_SYS_TEXT_BASE 0xfff80000 25 #endif 26 27 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 28 #define CONFIG_PCIE1 1 /* PCIE controller 1 */ 29 #define CONFIG_PCIE2 1 /* PCIE controller 2 */ 30 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 31 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 32 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 33 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 34 #define CONFIG_FSL_ELBC 1 35 36 /* 37 * Multicore config 38 */ 39 #define CONFIG_MP 40 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 41 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 42 43 /* 44 * DDR config 45 */ 46 #define CONFIG_SYS_FSL_DDR2 47 #undef CONFIG_FSL_DDR_INTERACTIVE 48 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 49 #define CONFIG_DDR_SPD 50 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 51 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 52 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 53 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 54 #define CONFIG_NUM_DDR_CONTROLLERS 2 55 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 56 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 57 #define CONFIG_DDR_ECC 58 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 59 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 60 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 61 #define CONFIG_VERY_BIG_RAM 62 63 #ifndef __ASSEMBLY__ 64 extern unsigned long get_board_sys_clk(unsigned long dummy); 65 extern unsigned long get_board_ddr_clk(unsigned long dummy); 66 #endif 67 68 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 69 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 70 71 /* 72 * These can be toggled for performance analysis, otherwise use default. 73 */ 74 #define CONFIG_L2_CACHE /* toggle L2 cache */ 75 #define CONFIG_BTB /* toggle branch predition */ 76 #define CONFIG_ENABLE_36BIT_PHYS 1 77 78 #define CONFIG_SYS_CCSRBAR 0xef000000 79 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 80 81 /* 82 * Diagnostics 83 */ 84 #define CONFIG_SYS_ALT_MEMTEST 85 #define CONFIG_SYS_MEMTEST_START 0x10000000 86 #define CONFIG_SYS_MEMTEST_END 0x20000000 87 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 88 CONFIG_SYS_POST_I2C) 89 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ 90 CONFIG_SYS_I2C_DS4510_ADDR, \ 91 CONFIG_SYS_I2C_EEPROM_ADDR, \ 92 CONFIG_SYS_I2C_LM90_ADDR, \ 93 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 94 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 95 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 96 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 97 CONFIG_SYS_I2C_PEX8518_ADDR, \ 98 CONFIG_SYS_I2C_RTC_ADDR} 99 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ 100 #define I2C_ADDR_IGNORE_LIST {0x50} 101 102 /* 103 * Memory map 104 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 105 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 106 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 107 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 108 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 109 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 110 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 111 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 112 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 113 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 114 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 115 */ 116 117 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 118 119 /* 120 * NAND flash configuration 121 */ 122 #define CONFIG_SYS_NAND_BASE 0xef800000 123 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 124 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 125 CONFIG_SYS_NAND_BASE2} 126 #define CONFIG_SYS_MAX_NAND_DEVICE 2 127 #define CONFIG_NAND_FSL_ELBC 128 129 /* 130 * NOR flash configuration 131 */ 132 #define CONFIG_SYS_FLASH_BASE 0xf8000000 133 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 134 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 135 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 136 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 137 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 138 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 139 #define CONFIG_FLASH_CFI_DRIVER 140 #define CONFIG_SYS_FLASH_CFI 141 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 142 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 143 {0xf7f40000, 0xc0000} } 144 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 145 146 /* 147 * Chip select configuration 148 */ 149 /* NOR Flash 0 on CS0 */ 150 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 151 BR_PS_16 | \ 152 BR_V) 153 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 154 OR_GPCM_CSNT | \ 155 OR_GPCM_XACS | \ 156 OR_GPCM_ACS_DIV2 | \ 157 OR_GPCM_SCY_8 | \ 158 OR_GPCM_TRLX | \ 159 OR_GPCM_EHTR | \ 160 OR_GPCM_EAD) 161 162 /* NOR Flash 1 on CS1 */ 163 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 164 BR_PS_16 | \ 165 BR_V) 166 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 167 168 /* NAND flash on CS2 */ 169 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 170 (2<<BR_DECC_SHIFT) | \ 171 BR_PS_8 | \ 172 BR_MS_FCM | \ 173 BR_V) 174 175 /* NAND flash on CS2 */ 176 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 177 OR_FCM_PGS | \ 178 OR_FCM_CSCT | \ 179 OR_FCM_CST | \ 180 OR_FCM_CHT | \ 181 OR_FCM_SCY_1 | \ 182 OR_FCM_TRLX | \ 183 OR_FCM_EHTR) 184 185 /* NAND flash on CS3 */ 186 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 187 (2<<BR_DECC_SHIFT) | \ 188 BR_PS_8 | \ 189 BR_MS_FCM | \ 190 BR_V) 191 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 192 193 /* 194 * Use L1 as initial stack 195 */ 196 #define CONFIG_SYS_INIT_RAM_LOCK 1 197 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 198 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 199 200 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 201 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 202 203 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 204 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 205 206 /* 207 * Serial Port 208 */ 209 #define CONFIG_CONS_INDEX 1 210 #define CONFIG_SYS_NS16550_SERIAL 211 #define CONFIG_SYS_NS16550_REG_SIZE 1 212 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 213 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 214 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 215 #define CONFIG_SYS_BAUDRATE_TABLE \ 216 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 217 #define CONFIG_BAUDRATE 115200 218 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 219 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 220 221 /* 222 * I2C 223 */ 224 #define CONFIG_SYS_I2C 225 #define CONFIG_SYS_I2C_FSL 226 #define CONFIG_SYS_FSL_I2C_SPEED 400000 227 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 228 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 229 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 230 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 231 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 232 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 233 234 /* PEX8518 slave I2C interface */ 235 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 236 237 /* I2C DS1631 temperature sensor */ 238 #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 239 #define CONFIG_DTT_DS1621 240 #define CONFIG_DTT_SENSORS { 0 } 241 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 242 243 /* I2C EEPROM - AT24C128B */ 244 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 245 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 246 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 247 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 248 249 /* I2C RTC */ 250 #define CONFIG_RTC_M41T11 1 251 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 252 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 253 254 /* GPIO/EEPROM/SRAM */ 255 #define CONFIG_DS4510 256 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 257 258 /* GPIO */ 259 #define CONFIG_PCA953X 260 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 261 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 262 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 263 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 264 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 265 266 /* 267 * PU = pulled high, PD = pulled low 268 * I = input, O = output, IO = input/output 269 */ 270 /* PCA9557 @ 0x18*/ 271 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 272 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 273 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 274 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 275 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 276 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 277 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ 278 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ 279 280 /* PCA9557 @ 0x1c*/ 281 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 282 #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ 283 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 284 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 285 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 286 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 287 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 288 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 289 290 /* PCA9557 @ 0x1e*/ 291 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 292 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 293 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 294 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 295 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 296 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ 297 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ 298 299 /* PCA9557 @ 0x1f */ 300 #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ 301 #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ 302 #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ 303 #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ 304 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ 305 306 /* 307 * General PCI 308 * Memory space is mapped 1-1, but I/O space must start from 0. 309 */ 310 /* PCIE1 - VPX P1 */ 311 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 312 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 313 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 314 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 315 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 316 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 317 318 /* PCIE2 - PEX8518 */ 319 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 320 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 321 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 322 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 323 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 324 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 325 326 /* 327 * Networking options 328 */ 329 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 330 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 331 #define CONFIG_TSEC_TBI 332 #define CONFIG_MII 1 /* MII PHY management */ 333 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 334 #define CONFIG_ETHPRIME "eTSEC2" 335 336 /* 337 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 338 * 1000mbps SGMII link 339 */ 340 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 341 TBICR_PHY_RESET \ 342 | TBICR_FULL_DUPLEX \ 343 | TBICR_SPEED1_SET \ 344 ) 345 346 #define CONFIG_TSEC1 1 347 #define CONFIG_TSEC1_NAME "eTSEC1" 348 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 349 #define TSEC1_PHY_ADDR 1 350 #define TSEC1_PHYIDX 0 351 #define CONFIG_HAS_ETH0 352 353 #define CONFIG_TSEC2 1 354 #define CONFIG_TSEC2_NAME "eTSEC2" 355 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 356 #define TSEC2_PHY_ADDR 2 357 #define TSEC2_PHYIDX 0 358 #define CONFIG_HAS_ETH1 359 360 /* 361 * Command configuration. 362 */ 363 #define CONFIG_CMD_DATE 364 #define CONFIG_CMD_DS4510 365 #define CONFIG_CMD_DS4510_INFO 366 #define CONFIG_CMD_DTT 367 #define CONFIG_CMD_EEPROM 368 #define CONFIG_CMD_JFFS2 369 #define CONFIG_CMD_NAND 370 #define CONFIG_CMD_PCA953X 371 #define CONFIG_CMD_PCA953X_INFO 372 #define CONFIG_CMD_PCI 373 #define CONFIG_CMD_PCI_ENUM 374 #define CONFIG_CMD_REGINFO 375 376 /* 377 * Miscellaneous configurable options 378 */ 379 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 380 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 381 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 382 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 383 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 384 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 385 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 386 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 387 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 388 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 389 #define CONFIG_PREBOOT /* enable preboot variable */ 390 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 391 392 /* 393 * For booting Linux, the board info and command line data 394 * have to be in the first 16 MB of memory, since this is 395 * the maximum mapped by the Linux kernel during initialization. 396 */ 397 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 398 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 399 400 /* 401 * Environment Configuration 402 */ 403 #define CONFIG_ENV_IS_IN_FLASH 1 404 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 405 #define CONFIG_ENV_SIZE 0x8000 406 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 407 408 /* 409 * Flash memory map: 410 * fff80000 - ffffffff Pri U-Boot (512 KB) 411 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 412 * fff00000 - fff3ffff Pri FDT (256KB) 413 * fef00000 - ffefffff Pri OS image (16MB) 414 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 415 * 416 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 417 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 418 * f7f00000 - f7f3ffff Sec FDT (256KB) 419 * f6f00000 - f7efffff Sec OS image (16MB) 420 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 421 */ 422 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 423 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 424 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 425 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 426 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 427 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 428 429 #define CONFIG_PROG_UBOOT1 \ 430 "$download_cmd $loadaddr $ubootfile; " \ 431 "if test $? -eq 0; then " \ 432 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 433 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 434 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 435 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 436 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 437 "if test $? -ne 0; then " \ 438 "echo PROGRAM FAILED; " \ 439 "else; " \ 440 "echo PROGRAM SUCCEEDED; " \ 441 "fi; " \ 442 "else; " \ 443 "echo DOWNLOAD FAILED; " \ 444 "fi;" 445 446 #define CONFIG_PROG_UBOOT2 \ 447 "$download_cmd $loadaddr $ubootfile; " \ 448 "if test $? -eq 0; then " \ 449 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 450 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 451 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 452 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 453 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 454 "if test $? -ne 0; then " \ 455 "echo PROGRAM FAILED; " \ 456 "else; " \ 457 "echo PROGRAM SUCCEEDED; " \ 458 "fi; " \ 459 "else; " \ 460 "echo DOWNLOAD FAILED; " \ 461 "fi;" 462 463 #define CONFIG_BOOT_OS_NET \ 464 "$download_cmd $osaddr $osfile; " \ 465 "if test $? -eq 0; then " \ 466 "if test -n $fdtaddr; then " \ 467 "$download_cmd $fdtaddr $fdtfile; " \ 468 "if test $? -eq 0; then " \ 469 "bootm $osaddr - $fdtaddr; " \ 470 "else; " \ 471 "echo FDT DOWNLOAD FAILED; " \ 472 "fi; " \ 473 "else; " \ 474 "bootm $osaddr; " \ 475 "fi; " \ 476 "else; " \ 477 "echo OS DOWNLOAD FAILED; " \ 478 "fi;" 479 480 #define CONFIG_PROG_OS1 \ 481 "$download_cmd $osaddr $osfile; " \ 482 "if test $? -eq 0; then " \ 483 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 484 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 485 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 486 "if test $? -ne 0; then " \ 487 "echo OS PROGRAM FAILED; " \ 488 "else; " \ 489 "echo OS PROGRAM SUCCEEDED; " \ 490 "fi; " \ 491 "else; " \ 492 "echo OS DOWNLOAD FAILED; " \ 493 "fi;" 494 495 #define CONFIG_PROG_OS2 \ 496 "$download_cmd $osaddr $osfile; " \ 497 "if test $? -eq 0; then " \ 498 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 499 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 500 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 501 "if test $? -ne 0; then " \ 502 "echo OS PROGRAM FAILED; " \ 503 "else; " \ 504 "echo OS PROGRAM SUCCEEDED; " \ 505 "fi; " \ 506 "else; " \ 507 "echo OS DOWNLOAD FAILED; " \ 508 "fi;" 509 510 #define CONFIG_PROG_FDT1 \ 511 "$download_cmd $fdtaddr $fdtfile; " \ 512 "if test $? -eq 0; then " \ 513 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 514 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 515 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 516 "if test $? -ne 0; then " \ 517 "echo FDT PROGRAM FAILED; " \ 518 "else; " \ 519 "echo FDT PROGRAM SUCCEEDED; " \ 520 "fi; " \ 521 "else; " \ 522 "echo FDT DOWNLOAD FAILED; " \ 523 "fi;" 524 525 #define CONFIG_PROG_FDT2 \ 526 "$download_cmd $fdtaddr $fdtfile; " \ 527 "if test $? -eq 0; then " \ 528 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 529 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 530 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 531 "if test $? -ne 0; then " \ 532 "echo FDT PROGRAM FAILED; " \ 533 "else; " \ 534 "echo FDT PROGRAM SUCCEEDED; " \ 535 "fi; " \ 536 "else; " \ 537 "echo FDT DOWNLOAD FAILED; " \ 538 "fi;" 539 540 #define CONFIG_EXTRA_ENV_SETTINGS \ 541 "autoload=yes\0" \ 542 "download_cmd=tftp\0" \ 543 "console_args=console=ttyS0,115200\0" \ 544 "root_args=root=/dev/nfs rw\0" \ 545 "misc_args=ip=on\0" \ 546 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 547 "bootfile=/home/user/file\0" \ 548 "osfile=/home/user/board.uImage\0" \ 549 "fdtfile=/home/user/board.dtb\0" \ 550 "ubootfile=/home/user/u-boot.bin\0" \ 551 "fdtaddr=0x1e00000\0" \ 552 "osaddr=0x1000000\0" \ 553 "loadaddr=0x1000000\0" \ 554 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 555 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 556 "prog_os1="CONFIG_PROG_OS1"\0" \ 557 "prog_os2="CONFIG_PROG_OS2"\0" \ 558 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 559 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 560 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 561 "bootcmd_flash1=run set_bootargs; " \ 562 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 563 "bootcmd_flash2=run set_bootargs; " \ 564 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 565 "bootcmd=run bootcmd_flash1\0" 566 #endif /* __CONFIG_H */ 567