1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2004-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite520x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_BOOKE 1 /* BOOKE */ 18 #define CONFIG_E500 1 /* BOOKE e500 family */ 19 #define CONFIG_MPC8548 1 20 #define CONFIG_XPEDITE5200 1 21 #define CONFIG_SYS_BOARD_NAME "XPedite5200" 22 #define CONFIG_SYS_FORM_PMC_XMC 1 23 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 24 25 #ifndef CONFIG_SYS_TEXT_BASE 26 #define CONFIG_SYS_TEXT_BASE 0xfff80000 27 #endif 28 29 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 30 #define CONFIG_PCI1 1 /* PCI controller 1 */ 31 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 32 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 33 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 34 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 35 36 /* 37 * DDR config 38 */ 39 #define CONFIG_SYS_FSL_DDR2 40 #undef CONFIG_FSL_DDR_INTERACTIVE 41 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 42 #define CONFIG_DDR_SPD 43 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 44 #define SPD_EEPROM_ADDRESS 0x54 45 #define CONFIG_NUM_DDR_CONTROLLERS 1 46 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 47 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 48 #define CONFIG_DDR_ECC 49 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 50 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 51 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 52 #define CONFIG_VERY_BIG_RAM 53 54 #define CONFIG_SYS_CLK_FREQ 66666666 55 56 /* 57 * These can be toggled for performance analysis, otherwise use default. 58 */ 59 #define CONFIG_L2_CACHE /* toggle L2 cache */ 60 #define CONFIG_BTB /* toggle branch predition */ 61 #define CONFIG_ENABLE_36BIT_PHYS 1 62 63 #define CONFIG_SYS_CCSRBAR 0xef000000 64 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 65 66 /* 67 * Diagnostics 68 */ 69 #define CONFIG_SYS_ALT_MEMTEST 70 #define CONFIG_SYS_MEMTEST_START 0x10000000 71 #define CONFIG_SYS_MEMTEST_END 0x20000000 72 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 73 CONFIG_SYS_POST_I2C) 74 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_MAX1237_ADDR, \ 75 CONFIG_SYS_I2C_EEPROM_ADDR, \ 76 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 77 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 78 CONFIG_SYS_I2C_RTC_ADDR} 79 80 /* 81 * Memory map 82 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 83 * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable 84 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 85 * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable 86 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 87 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 88 * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable 89 * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable 90 */ 91 92 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 93 94 /* 95 * NAND flash configuration 96 */ 97 #define CONFIG_SYS_NAND_BASE 0xef800000 98 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 99 #define CONFIG_SYS_MAX_NAND_DEVICE 1 100 #define CONFIG_NAND_ACTL 101 #define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */ 102 #define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */ 103 #define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */ 104 #define CONFIG_SYS_NAND_ACTL_DELAY 25 105 106 /* 107 * NOR flash configuration 108 */ 109 #define CONFIG_SYS_FLASH_BASE 0xfc000000 110 #define CONFIG_SYS_FLASH_BASE2 0xf8000000 111 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 112 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 113 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 114 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 115 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 116 #define CONFIG_FLASH_CFI_DRIVER 117 #define CONFIG_SYS_FLASH_CFI 118 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 119 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 120 {0xfbf40000, 0xc0000} } 121 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 122 123 /* 124 * Chip select configuration 125 */ 126 /* NOR Flash 0 on CS0 */ 127 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 128 BR_PS_16 | \ 129 BR_V) 130 #define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \ 131 OR_GPCM_ACS_DIV4 | \ 132 OR_GPCM_SCY_8) 133 134 /* NOR Flash 1 on CS1 */ 135 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 136 BR_PS_16 | \ 137 BR_V) 138 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 139 140 /* NAND flash on CS2 */ 141 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 142 BR_PS_8 | \ 143 BR_V) 144 145 /* NAND flash on CS2 */ 146 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 147 OR_GPCM_BCTLD | \ 148 OR_GPCM_CSNT | \ 149 OR_GPCM_ACS_DIV4 | \ 150 OR_GPCM_SCY_4 | \ 151 OR_GPCM_TRLX | \ 152 OR_GPCM_EHTR) 153 154 /* NAND flash on CS3 */ 155 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 156 BR_PS_8 | \ 157 BR_V) 158 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 159 160 /* 161 * Use L1 as initial stack 162 */ 163 #define CONFIG_SYS_INIT_RAM_LOCK 1 164 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 165 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 166 167 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 168 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 169 170 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 171 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 172 173 /* 174 * Serial Port 175 */ 176 #define CONFIG_CONS_INDEX 1 177 #define CONFIG_SYS_NS16550_SERIAL 178 #define CONFIG_SYS_NS16550_REG_SIZE 1 179 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 180 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 181 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 182 #define CONFIG_SYS_BAUDRATE_TABLE \ 183 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 184 #define CONFIG_BAUDRATE 115200 185 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 186 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 187 188 /* 189 * I2C 190 */ 191 #define CONFIG_SYS_I2C 192 #define CONFIG_SYS_I2C_FSL 193 #define CONFIG_SYS_FSL_I2C_SPEED 400000 194 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 195 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 196 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 197 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 198 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 199 200 /* I2C EEPROM */ 201 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 202 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 203 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 204 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 205 206 /* I2C RTC */ 207 #define CONFIG_RTC_M41T11 1 208 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 209 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 210 211 /* GPIO */ 212 #define CONFIG_PCA953X 213 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 214 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19 215 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 216 217 /* PCA957 @ 0x18 */ 218 #define CONFIG_SYS_PCA953X_BRD_CFG0 0x01 219 #define CONFIG_SYS_PCA953X_BRD_CFG1 0x02 220 #define CONFIG_SYS_PCA953X_BRD_CFG2 0x04 221 #define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08 222 #define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10 223 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 224 #define CONFIG_SYS_PCA953X_MONARCH 0x40 225 #define CONFIG_SYS_PCA953X_EREADY 0x80 226 227 /* PCA957 @ 0x19 */ 228 #define CONFIG_SYS_PCA953X_P14_IO0 0x01 229 #define CONFIG_SYS_PCA953X_P14_IO1 0x02 230 #define CONFIG_SYS_PCA953X_P14_IO2 0x04 231 #define CONFIG_SYS_PCA953X_P14_IO3 0x08 232 #define CONFIG_SYS_PCA953X_P14_IO4 0x10 233 #define CONFIG_SYS_PCA953X_P14_IO5 0x20 234 #define CONFIG_SYS_PCA953X_P14_IO6 0x40 235 #define CONFIG_SYS_PCA953X_P14_IO7 0x80 236 237 /* 12-bit ADC used to measure CPU diode */ 238 #define CONFIG_SYS_I2C_MAX1237_ADDR 0x34 239 240 /* 241 * General PCI 242 * Memory space is mapped 1-1, but I/O space must start from 0. 243 */ 244 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 245 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS 246 #define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */ 247 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 248 #define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000 249 #define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */ 250 251 /* 252 * Networking options 253 */ 254 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 255 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 256 #define CONFIG_MII 1 /* MII PHY management */ 257 #define CONFIG_ETHPRIME "eTSEC1" 258 259 #define CONFIG_TSEC1 1 260 #define CONFIG_TSEC1_NAME "eTSEC1" 261 #define TSEC1_FLAGS TSEC_GIGABIT 262 #define TSEC1_PHY_ADDR 1 263 #define TSEC1_PHYIDX 0 264 #define CONFIG_HAS_ETH0 265 266 #define CONFIG_TSEC2 1 267 #define CONFIG_TSEC2_NAME "eTSEC2" 268 #define TSEC2_FLAGS TSEC_GIGABIT 269 #define TSEC2_PHY_ADDR 2 270 #define TSEC2_PHYIDX 0 271 #define CONFIG_HAS_ETH1 272 273 #define CONFIG_TSEC3 1 274 #define CONFIG_TSEC3_NAME "eTSEC3" 275 #define TSEC3_FLAGS TSEC_GIGABIT 276 #define TSEC3_PHY_ADDR 3 277 #define TSEC3_PHYIDX 0 278 #define CONFIG_HAS_ETH2 279 280 #define CONFIG_TSEC4 1 281 #define CONFIG_TSEC4_NAME "eTSEC4" 282 #define TSEC4_FLAGS TSEC_GIGABIT 283 #define TSEC4_PHY_ADDR 4 284 #define TSEC4_PHYIDX 0 285 #define CONFIG_HAS_ETH3 286 287 /* 288 * BOOTP options 289 */ 290 #define CONFIG_BOOTP_BOOTFILESIZE 291 #define CONFIG_BOOTP_BOOTPATH 292 #define CONFIG_BOOTP_GATEWAY 293 294 /* 295 * Command configuration. 296 */ 297 #define CONFIG_CMD_DATE 298 #define CONFIG_CMD_EEPROM 299 #define CONFIG_CMD_JFFS2 300 #define CONFIG_CMD_NAND 301 #define CONFIG_CMD_PCA953X 302 #define CONFIG_CMD_PCA953X_INFO 303 #define CONFIG_CMD_PCI 304 #define CONFIG_CMD_PCI_ENUM 305 #define CONFIG_CMD_REGINFO 306 307 /* 308 * Miscellaneous configurable options 309 */ 310 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 311 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 312 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 313 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 314 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 315 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 316 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 317 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 318 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 319 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 320 #define CONFIG_PREBOOT /* enable preboot variable */ 321 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 322 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ 323 324 /* 325 * For booting Linux, the board info and command line data 326 * have to be in the first 16 MB of memory, since this is 327 * the maximum mapped by the Linux kernel during initialization. 328 */ 329 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 330 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 331 332 /* 333 * Environment Configuration 334 */ 335 #define CONFIG_ENV_IS_IN_FLASH 1 336 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 337 #define CONFIG_ENV_SIZE 0x8000 338 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 339 340 /* 341 * Flash memory map: 342 * fff80000 - ffffffff Pri U-Boot (512 KB) 343 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 344 * fff00000 - fff3ffff Pri FDT (256KB) 345 * fef00000 - ffefffff Pri OS image (16MB) 346 * fc000000 - feefffff Pri OS Use/Filesystem (47MB) 347 * 348 * fbf80000 - fbffffff Sec U-Boot (512 KB) 349 * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB) 350 * fbf00000 - fbf3ffff Sec FDT (256KB) 351 * faf00000 - fbefffff Sec OS image (16MB) 352 * f8000000 - faefffff Sec OS Use/Filesystem (47MB) 353 */ 354 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 355 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xfbf80000) 356 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 357 #define CONFIG_FDT2_ENV_ADDR __stringify(0xfbf00000) 358 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 359 #define CONFIG_OS2_ENV_ADDR __stringify(0xfaf00000) 360 361 #define CONFIG_PROG_UBOOT1 \ 362 "$download_cmd $loadaddr $ubootfile; " \ 363 "if test $? -eq 0; then " \ 364 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 365 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 366 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 367 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 368 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 369 "if test $? -ne 0; then " \ 370 "echo PROGRAM FAILED; " \ 371 "else; " \ 372 "echo PROGRAM SUCCEEDED; " \ 373 "fi; " \ 374 "else; " \ 375 "echo DOWNLOAD FAILED; " \ 376 "fi;" 377 378 #define CONFIG_PROG_UBOOT2 \ 379 "$download_cmd $loadaddr $ubootfile; " \ 380 "if test $? -eq 0; then " \ 381 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 382 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 383 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 384 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 385 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 386 "if test $? -ne 0; then " \ 387 "echo PROGRAM FAILED; " \ 388 "else; " \ 389 "echo PROGRAM SUCCEEDED; " \ 390 "fi; " \ 391 "else; " \ 392 "echo DOWNLOAD FAILED; " \ 393 "fi;" 394 395 #define CONFIG_BOOT_OS_NET \ 396 "$download_cmd $osaddr $osfile; " \ 397 "if test $? -eq 0; then " \ 398 "if test -n $fdtaddr; then " \ 399 "$download_cmd $fdtaddr $fdtfile; " \ 400 "if test $? -eq 0; then " \ 401 "bootm $osaddr - $fdtaddr; " \ 402 "else; " \ 403 "echo FDT DOWNLOAD FAILED; " \ 404 "fi; " \ 405 "else; " \ 406 "bootm $osaddr; " \ 407 "fi; " \ 408 "else; " \ 409 "echo OS DOWNLOAD FAILED; " \ 410 "fi;" 411 412 #define CONFIG_PROG_OS1 \ 413 "$download_cmd $osaddr $osfile; " \ 414 "if test $? -eq 0; then " \ 415 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 416 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 417 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 418 "if test $? -ne 0; then " \ 419 "echo OS PROGRAM FAILED; " \ 420 "else; " \ 421 "echo OS PROGRAM SUCCEEDED; " \ 422 "fi; " \ 423 "else; " \ 424 "echo OS DOWNLOAD FAILED; " \ 425 "fi;" 426 427 #define CONFIG_PROG_OS2 \ 428 "$download_cmd $osaddr $osfile; " \ 429 "if test $? -eq 0; then " \ 430 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 431 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 432 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 433 "if test $? -ne 0; then " \ 434 "echo OS PROGRAM FAILED; " \ 435 "else; " \ 436 "echo OS PROGRAM SUCCEEDED; " \ 437 "fi; " \ 438 "else; " \ 439 "echo OS DOWNLOAD FAILED; " \ 440 "fi;" 441 442 #define CONFIG_PROG_FDT1 \ 443 "$download_cmd $fdtaddr $fdtfile; " \ 444 "if test $? -eq 0; then " \ 445 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 446 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 447 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 448 "if test $? -ne 0; then " \ 449 "echo FDT PROGRAM FAILED; " \ 450 "else; " \ 451 "echo FDT PROGRAM SUCCEEDED; " \ 452 "fi; " \ 453 "else; " \ 454 "echo FDT DOWNLOAD FAILED; " \ 455 "fi;" 456 457 #define CONFIG_PROG_FDT2 \ 458 "$download_cmd $fdtaddr $fdtfile; " \ 459 "if test $? -eq 0; then " \ 460 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 461 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 462 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 463 "if test $? -ne 0; then " \ 464 "echo FDT PROGRAM FAILED; " \ 465 "else; " \ 466 "echo FDT PROGRAM SUCCEEDED; " \ 467 "fi; " \ 468 "else; " \ 469 "echo FDT DOWNLOAD FAILED; " \ 470 "fi;" 471 472 #define CONFIG_EXTRA_ENV_SETTINGS \ 473 "autoload=yes\0" \ 474 "download_cmd=tftp\0" \ 475 "console_args=console=ttyS0,115200\0" \ 476 "root_args=root=/dev/nfs rw\0" \ 477 "misc_args=ip=on\0" \ 478 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 479 "bootfile=/home/user/file\0" \ 480 "osfile=/home/user/board.uImage\0" \ 481 "fdtfile=/home/user/board.dtb\0" \ 482 "ubootfile=/home/user/u-boot.bin\0" \ 483 "fdtaddr=0x1e00000\0" \ 484 "osaddr=0x1000000\0" \ 485 "loadaddr=0x1000000\0" \ 486 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 487 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 488 "prog_os1="CONFIG_PROG_OS1"\0" \ 489 "prog_os2="CONFIG_PROG_OS2"\0" \ 490 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 491 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 492 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 493 "bootcmd_flash1=run set_bootargs; " \ 494 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 495 "bootcmd_flash2=run set_bootargs; " \ 496 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 497 "bootcmd=run bootcmd_flash1\0" 498 #endif /* __CONFIG_H */ 499