1 /* 2 * Copyright 2008 Extreme Engineering Solutions, Inc. 3 * Copyright 2004-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite520x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_BOOKE 1 /* BOOKE */ 18 #define CONFIG_E500 1 /* BOOKE e500 family */ 19 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ 20 #define CONFIG_MPC8548 1 21 #define CONFIG_XPEDITE5200 1 22 #define CONFIG_SYS_BOARD_NAME "XPedite5200" 23 #define CONFIG_SYS_FORM_PMC_XMC 1 24 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 25 26 #ifndef CONFIG_SYS_TEXT_BASE 27 #define CONFIG_SYS_TEXT_BASE 0xfff80000 28 #endif 29 30 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 31 #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ 32 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 33 #define CONFIG_PCI1 1 /* PCI controller 1 */ 34 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 35 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 36 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 37 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 38 39 /* 40 * DDR config 41 */ 42 #define CONFIG_FSL_DDR2 43 #undef CONFIG_FSL_DDR_INTERACTIVE 44 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 45 #define CONFIG_DDR_SPD 46 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 47 #define SPD_EEPROM_ADDRESS 0x54 48 #define CONFIG_NUM_DDR_CONTROLLERS 1 49 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 50 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 51 #define CONFIG_DDR_ECC 52 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 53 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 54 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 55 #define CONFIG_VERY_BIG_RAM 56 57 #define CONFIG_SYS_CLK_FREQ 66666666 58 59 /* 60 * These can be toggled for performance analysis, otherwise use default. 61 */ 62 #define CONFIG_L2_CACHE /* toggle L2 cache */ 63 #define CONFIG_BTB /* toggle branch predition */ 64 #define CONFIG_ENABLE_36BIT_PHYS 1 65 66 #define CONFIG_SYS_CCSRBAR 0xef000000 67 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 68 69 /* 70 * Diagnostics 71 */ 72 #define CONFIG_SYS_ALT_MEMTEST 73 #define CONFIG_SYS_MEMTEST_START 0x10000000 74 #define CONFIG_SYS_MEMTEST_END 0x20000000 75 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 76 CONFIG_SYS_POST_I2C) 77 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_MAX1237_ADDR, \ 78 CONFIG_SYS_I2C_EEPROM_ADDR, \ 79 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 80 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 81 CONFIG_SYS_I2C_RTC_ADDR} 82 83 /* 84 * Memory map 85 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 86 * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable 87 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 88 * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable 89 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 90 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 91 * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable 92 * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable 93 */ 94 95 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 96 97 /* 98 * NAND flash configuration 99 */ 100 #define CONFIG_SYS_NAND_BASE 0xef800000 101 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 102 #define CONFIG_SYS_MAX_NAND_DEVICE 1 103 #define CONFIG_NAND_ACTL 104 #define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */ 105 #define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */ 106 #define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */ 107 #define CONFIG_SYS_NAND_ACTL_DELAY 25 108 109 /* 110 * NOR flash configuration 111 */ 112 #define CONFIG_SYS_FLASH_BASE 0xfc000000 113 #define CONFIG_SYS_FLASH_BASE2 0xf8000000 114 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 115 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 116 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 117 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 118 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 119 #define CONFIG_FLASH_CFI_DRIVER 120 #define CONFIG_SYS_FLASH_CFI 121 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 122 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 123 {0xfbf40000, 0xc0000} } 124 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 125 126 /* 127 * Chip select configuration 128 */ 129 /* NOR Flash 0 on CS0 */ 130 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 131 BR_PS_16 | \ 132 BR_V) 133 #define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \ 134 OR_GPCM_ACS_DIV4 | \ 135 OR_GPCM_SCY_8) 136 137 /* NOR Flash 1 on CS1 */ 138 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 139 BR_PS_16 | \ 140 BR_V) 141 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 142 143 /* NAND flash on CS2 */ 144 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 145 BR_PS_8 | \ 146 BR_V) 147 148 /* NAND flash on CS2 */ 149 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 150 OR_GPCM_BCTLD | \ 151 OR_GPCM_CSNT | \ 152 OR_GPCM_ACS_DIV4 | \ 153 OR_GPCM_SCY_4 | \ 154 OR_GPCM_TRLX | \ 155 OR_GPCM_EHTR) 156 157 /* NAND flash on CS3 */ 158 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 159 BR_PS_8 | \ 160 BR_V) 161 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 162 163 /* 164 * Use L1 as initial stack 165 */ 166 #define CONFIG_SYS_INIT_RAM_LOCK 1 167 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 168 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 169 170 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 171 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 172 173 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 174 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 175 176 /* 177 * Serial Port 178 */ 179 #define CONFIG_CONS_INDEX 1 180 #define CONFIG_SYS_NS16550 181 #define CONFIG_SYS_NS16550_SERIAL 182 #define CONFIG_SYS_NS16550_REG_SIZE 1 183 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 184 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 185 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 186 #define CONFIG_SYS_BAUDRATE_TABLE \ 187 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 188 #define CONFIG_BAUDRATE 115200 189 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 190 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 191 192 /* 193 * Use the HUSH parser 194 */ 195 #define CONFIG_SYS_HUSH_PARSER 196 197 /* 198 * Pass open firmware flat tree 199 */ 200 #define CONFIG_OF_LIBFDT 1 201 #define CONFIG_OF_BOARD_SETUP 1 202 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 203 204 /* 205 * I2C 206 */ 207 #define CONFIG_SYS_I2C 208 #define CONFIG_SYS_I2C_FSL 209 #define CONFIG_SYS_FSL_I2C_SPEED 400000 210 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 211 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 212 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 213 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 214 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 215 216 /* I2C EEPROM */ 217 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 218 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 219 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 220 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 221 222 /* I2C RTC */ 223 #define CONFIG_RTC_M41T11 1 224 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 225 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 226 227 /* GPIO */ 228 #define CONFIG_PCA953X 229 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 230 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19 231 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 232 233 /* PCA957 @ 0x18 */ 234 #define CONFIG_SYS_PCA953X_BRD_CFG0 0x01 235 #define CONFIG_SYS_PCA953X_BRD_CFG1 0x02 236 #define CONFIG_SYS_PCA953X_BRD_CFG2 0x04 237 #define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08 238 #define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10 239 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 240 #define CONFIG_SYS_PCA953X_MONARCH 0x40 241 #define CONFIG_SYS_PCA953X_EREADY 0x80 242 243 /* PCA957 @ 0x19 */ 244 #define CONFIG_SYS_PCA953X_P14_IO0 0x01 245 #define CONFIG_SYS_PCA953X_P14_IO1 0x02 246 #define CONFIG_SYS_PCA953X_P14_IO2 0x04 247 #define CONFIG_SYS_PCA953X_P14_IO3 0x08 248 #define CONFIG_SYS_PCA953X_P14_IO4 0x10 249 #define CONFIG_SYS_PCA953X_P14_IO5 0x20 250 #define CONFIG_SYS_PCA953X_P14_IO6 0x40 251 #define CONFIG_SYS_PCA953X_P14_IO7 0x80 252 253 /* 12-bit ADC used to measure CPU diode */ 254 #define CONFIG_SYS_I2C_MAX1237_ADDR 0x34 255 256 /* 257 * General PCI 258 * Memory space is mapped 1-1, but I/O space must start from 0. 259 */ 260 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 261 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS 262 #define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */ 263 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 264 #define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000 265 #define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */ 266 267 /* 268 * Networking options 269 */ 270 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 271 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 272 #define CONFIG_MII 1 /* MII PHY management */ 273 #define CONFIG_ETHPRIME "eTSEC1" 274 275 #define CONFIG_TSEC1 1 276 #define CONFIG_TSEC1_NAME "eTSEC1" 277 #define TSEC1_FLAGS TSEC_GIGABIT 278 #define TSEC1_PHY_ADDR 1 279 #define TSEC1_PHYIDX 0 280 #define CONFIG_HAS_ETH0 281 282 #define CONFIG_TSEC2 1 283 #define CONFIG_TSEC2_NAME "eTSEC2" 284 #define TSEC2_FLAGS TSEC_GIGABIT 285 #define TSEC2_PHY_ADDR 2 286 #define TSEC2_PHYIDX 0 287 #define CONFIG_HAS_ETH1 288 289 #define CONFIG_TSEC3 1 290 #define CONFIG_TSEC3_NAME "eTSEC3" 291 #define TSEC3_FLAGS TSEC_GIGABIT 292 #define TSEC3_PHY_ADDR 3 293 #define TSEC3_PHYIDX 0 294 #define CONFIG_HAS_ETH2 295 296 #define CONFIG_TSEC4 1 297 #define CONFIG_TSEC4_NAME "eTSEC4" 298 #define TSEC4_FLAGS TSEC_GIGABIT 299 #define TSEC4_PHY_ADDR 4 300 #define TSEC4_PHYIDX 0 301 #define CONFIG_HAS_ETH3 302 303 /* 304 * BOOTP options 305 */ 306 #define CONFIG_BOOTP_BOOTFILESIZE 307 #define CONFIG_BOOTP_BOOTPATH 308 #define CONFIG_BOOTP_GATEWAY 309 310 /* 311 * Command configuration. 312 */ 313 #include <config_cmd_default.h> 314 315 #define CONFIG_CMD_ASKENV 316 #define CONFIG_CMD_DATE 317 #define CONFIG_CMD_DHCP 318 #define CONFIG_CMD_EEPROM 319 #define CONFIG_CMD_ELF 320 #define CONFIG_CMD_SAVEENV 321 #define CONFIG_CMD_FLASH 322 #define CONFIG_CMD_I2C 323 #define CONFIG_CMD_JFFS2 324 #define CONFIG_CMD_MII 325 #define CONFIG_CMD_NAND 326 #define CONFIG_CMD_NET 327 #define CONFIG_CMD_PCA953X 328 #define CONFIG_CMD_PCA953X_INFO 329 #define CONFIG_CMD_PCI 330 #define CONFIG_CMD_PCI_ENUM 331 #define CONFIG_CMD_PING 332 #define CONFIG_CMD_SNTP 333 #define CONFIG_CMD_REGINFO 334 335 /* 336 * Miscellaneous configurable options 337 */ 338 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 339 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 340 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 341 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 342 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 343 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 344 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 345 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 346 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 347 #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ 348 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 349 #define CONFIG_PREBOOT /* enable preboot variable */ 350 #define CONFIG_FIT 1 351 #define CONFIG_FIT_VERBOSE 1 352 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 353 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ 354 355 /* 356 * For booting Linux, the board info and command line data 357 * have to be in the first 16 MB of memory, since this is 358 * the maximum mapped by the Linux kernel during initialization. 359 */ 360 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 361 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 362 363 /* 364 * Environment Configuration 365 */ 366 #define CONFIG_ENV_IS_IN_FLASH 1 367 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 368 #define CONFIG_ENV_SIZE 0x8000 369 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 370 371 /* 372 * Flash memory map: 373 * fff80000 - ffffffff Pri U-Boot (512 KB) 374 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 375 * fff00000 - fff3ffff Pri FDT (256KB) 376 * fef00000 - ffefffff Pri OS image (16MB) 377 * fc000000 - feefffff Pri OS Use/Filesystem (47MB) 378 * 379 * fbf80000 - fbffffff Sec U-Boot (512 KB) 380 * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB) 381 * fbf00000 - fbf3ffff Sec FDT (256KB) 382 * faf00000 - fbefffff Sec OS image (16MB) 383 * f8000000 - faefffff Sec OS Use/Filesystem (47MB) 384 */ 385 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 386 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xfbf80000) 387 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 388 #define CONFIG_FDT2_ENV_ADDR __stringify(0xfbf00000) 389 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 390 #define CONFIG_OS2_ENV_ADDR __stringify(0xfaf00000) 391 392 #define CONFIG_PROG_UBOOT1 \ 393 "$download_cmd $loadaddr $ubootfile; " \ 394 "if test $? -eq 0; then " \ 395 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 396 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 397 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 398 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 399 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 400 "if test $? -ne 0; then " \ 401 "echo PROGRAM FAILED; " \ 402 "else; " \ 403 "echo PROGRAM SUCCEEDED; " \ 404 "fi; " \ 405 "else; " \ 406 "echo DOWNLOAD FAILED; " \ 407 "fi;" 408 409 #define CONFIG_PROG_UBOOT2 \ 410 "$download_cmd $loadaddr $ubootfile; " \ 411 "if test $? -eq 0; then " \ 412 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 413 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 414 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 415 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 416 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 417 "if test $? -ne 0; then " \ 418 "echo PROGRAM FAILED; " \ 419 "else; " \ 420 "echo PROGRAM SUCCEEDED; " \ 421 "fi; " \ 422 "else; " \ 423 "echo DOWNLOAD FAILED; " \ 424 "fi;" 425 426 #define CONFIG_BOOT_OS_NET \ 427 "$download_cmd $osaddr $osfile; " \ 428 "if test $? -eq 0; then " \ 429 "if test -n $fdtaddr; then " \ 430 "$download_cmd $fdtaddr $fdtfile; " \ 431 "if test $? -eq 0; then " \ 432 "bootm $osaddr - $fdtaddr; " \ 433 "else; " \ 434 "echo FDT DOWNLOAD FAILED; " \ 435 "fi; " \ 436 "else; " \ 437 "bootm $osaddr; " \ 438 "fi; " \ 439 "else; " \ 440 "echo OS DOWNLOAD FAILED; " \ 441 "fi;" 442 443 #define CONFIG_PROG_OS1 \ 444 "$download_cmd $osaddr $osfile; " \ 445 "if test $? -eq 0; then " \ 446 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 447 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 448 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 449 "if test $? -ne 0; then " \ 450 "echo OS PROGRAM FAILED; " \ 451 "else; " \ 452 "echo OS PROGRAM SUCCEEDED; " \ 453 "fi; " \ 454 "else; " \ 455 "echo OS DOWNLOAD FAILED; " \ 456 "fi;" 457 458 #define CONFIG_PROG_OS2 \ 459 "$download_cmd $osaddr $osfile; " \ 460 "if test $? -eq 0; then " \ 461 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 462 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 463 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 464 "if test $? -ne 0; then " \ 465 "echo OS PROGRAM FAILED; " \ 466 "else; " \ 467 "echo OS PROGRAM SUCCEEDED; " \ 468 "fi; " \ 469 "else; " \ 470 "echo OS DOWNLOAD FAILED; " \ 471 "fi;" 472 473 #define CONFIG_PROG_FDT1 \ 474 "$download_cmd $fdtaddr $fdtfile; " \ 475 "if test $? -eq 0; then " \ 476 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 477 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 478 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 479 "if test $? -ne 0; then " \ 480 "echo FDT PROGRAM FAILED; " \ 481 "else; " \ 482 "echo FDT PROGRAM SUCCEEDED; " \ 483 "fi; " \ 484 "else; " \ 485 "echo FDT DOWNLOAD FAILED; " \ 486 "fi;" 487 488 #define CONFIG_PROG_FDT2 \ 489 "$download_cmd $fdtaddr $fdtfile; " \ 490 "if test $? -eq 0; then " \ 491 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 492 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 493 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 494 "if test $? -ne 0; then " \ 495 "echo FDT PROGRAM FAILED; " \ 496 "else; " \ 497 "echo FDT PROGRAM SUCCEEDED; " \ 498 "fi; " \ 499 "else; " \ 500 "echo FDT DOWNLOAD FAILED; " \ 501 "fi;" 502 503 #define CONFIG_EXTRA_ENV_SETTINGS \ 504 "autoload=yes\0" \ 505 "download_cmd=tftp\0" \ 506 "console_args=console=ttyS0,115200\0" \ 507 "root_args=root=/dev/nfs rw\0" \ 508 "misc_args=ip=on\0" \ 509 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 510 "bootfile=/home/user/file\0" \ 511 "osfile=/home/user/board.uImage\0" \ 512 "fdtfile=/home/user/board.dtb\0" \ 513 "ubootfile=/home/user/u-boot.bin\0" \ 514 "fdtaddr=c00000\0" \ 515 "osaddr=0x1000000\0" \ 516 "loadaddr=0x1000000\0" \ 517 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 518 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 519 "prog_os1="CONFIG_PROG_OS1"\0" \ 520 "prog_os2="CONFIG_PROG_OS2"\0" \ 521 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 522 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 523 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 524 "bootcmd_flash1=run set_bootargs; " \ 525 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 526 "bootcmd_flash2=run set_bootargs; " \ 527 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 528 "bootcmd=run bootcmd_flash1\0" 529 #endif /* __CONFIG_H */ 530