1 /*
2  * Copyright 2009 Extreme Engineering Solutions, Inc.
3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 /*
9  * xpedite517x board configuration file
10  */
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /*
15  * High Level Configuration Options
16  */
17 #define CONFIG_XPEDITE5140	1	/* MPC8641HPCN board specific */
18 #define CONFIG_SYS_BOARD_NAME	"XPedite5170"
19 #define CONFIG_SYS_FORM_3U_VPX	1
20 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
21 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
22 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
23 #define CONFIG_HIGH_BATS	1	/* High BATs supported and enabled */
24 #define CONFIG_ALTIVEC		1
25 
26 #define	CONFIG_SYS_TEXT_BASE	0xfff00000
27 
28 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
29 #define CONFIG_PCIE1		1	/* PCIE controller 1 */
30 #define CONFIG_PCIE2		1	/* PCIE controller 2 */
31 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
32 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
33 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
34 
35 /*
36  * DDR config
37  */
38 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
39 #define CONFIG_DDR_SPD
40 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
41 #define SPD_EEPROM_ADDRESS1		0x54	/* Both channels use the */
42 #define SPD_EEPROM_ADDRESS2		0x54	/* same SPD data         */
43 #define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
44 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
45 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
46 #define CONFIG_DDR_ECC
47 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
48 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
49 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
50 #define CONFIG_VERY_BIG_RAM
51 #define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
52 
53 /*
54  * virtual address to be used for temporary mappings.  There
55  * should be 128k free at this VA.
56  */
57 #define CONFIG_SYS_SCRATCH_VA	0xe0000000
58 
59 #ifndef __ASSEMBLY__
60 extern unsigned long get_board_sys_clk(unsigned long dummy);
61 #endif
62 
63 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC86xx */
64 
65 /*
66  * L2CR setup
67  */
68 #define CONFIG_SYS_L2
69 #define L2_INIT		0
70 #define L2_ENABLE	(L2CR_L2E)
71 
72 /*
73  * Base addresses -- Note these are effective addresses where the
74  * actual resources get mapped (not physical addresses)
75  */
76 #define CONFIG_SYS_CCSRBAR		0xef000000	/* relocated CCSRBAR */
77 #define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR
78 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
79 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
80 #define CONFIG_SYS_IMMR			CONFIG_SYS_CCSRBAR
81 
82 /*
83  * Diagnostics
84  */
85 #define CONFIG_SYS_ALT_MEMTEST
86 #define CONFIG_SYS_MEMTEST_START	0x10000000
87 #define CONFIG_SYS_MEMTEST_END		0x20000000
88 #define CONFIG_POST			(CONFIG_SYS_POST_MEMORY |\
89 					 CONFIG_SYS_POST_I2C)
90 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
91 #define I2C_ADDR_IGNORE_LIST		{0x50}
92 
93 /*
94  * Memory map
95  * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
96  * 0x8000_0000	0xbfff_ffff	PCIe1 Mem		1G non-cacheable
97  * 0xc000_0000	0xcfff_ffff	PCIe2 Mem		256M non-cacheable
98  * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
99  * 0xe800_0000	0xe87f_ffff	PCIe1 IO		8M non-cacheable
100  * 0xe880_0000	0xe8ff_ffff	PCIe2 IO		8M non-cacheable
101  * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
102  * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
103  * 0xf000_0000	0xf7ff_ffff	NOR Flash 2		128M non-cacheable
104  * 0xf800_0000	0xffff_ffff	NOR Flash 1		128M non-cacheable
105  */
106 
107 #define CONFIG_SYS_LBC_LCRR		(LCRR_CLKDIV_4 | LCRR_EADC_3)
108 
109 /*
110  * NAND flash configuration
111  */
112 #define CONFIG_SYS_NAND_BASE		0xef800000
113 #define CONFIG_SYS_NAND_BASE2		0xef840000	/* Unused at this time */
114 #define CONFIG_SYS_NAND_BASE_LIST 	{CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
115 #define CONFIG_SYS_MAX_NAND_DEVICE	2
116 #define CONFIG_NAND_ACTL
117 #define CONFIG_SYS_NAND_ACTL_ALE 	(1 << 14)	/* C_LA14 */
118 #define CONFIG_SYS_NAND_ACTL_CLE 	(1 << 15)	/* C_LA15 */
119 #define CONFIG_SYS_NAND_ACTL_NCE	0		/* NCE not controlled by ADDR */
120 #define CONFIG_SYS_NAND_ACTL_DELAY	25
121 #define CONFIG_JFFS2_NAND
122 
123 /*
124  * NOR flash configuration
125  */
126 #define CONFIG_SYS_FLASH_BASE		0xf8000000
127 #define CONFIG_SYS_FLASH_BASE2		0xf0000000
128 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
129 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
130 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
131 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
132 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
133 #define CONFIG_FLASH_CFI_DRIVER
134 #define CONFIG_SYS_FLASH_CFI
135 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
136 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff00000, 0xc0000}, \
137 						  {0xf7f00000, 0xc0000} }
138 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
139 #define CONFIG_SYS_MONITOR_BASE_EARLY	0xfff00000	/* early monitor loc */
140 
141 /*
142  * Chip select configuration
143  */
144 /* NOR Flash 0 on CS0 */
145 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	|\
146 				 BR_PS_16		|\
147 				 BR_V)
148 #define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		|\
149 				 OR_GPCM_CSNT		|\
150 				 OR_GPCM_XACS		|\
151 				 OR_GPCM_ACS_DIV2	|\
152 				 OR_GPCM_SCY_8		|\
153 				 OR_GPCM_TRLX		|\
154 				 OR_GPCM_EHTR		|\
155 				 OR_GPCM_EAD)
156 
157 /* NOR Flash 1 on CS1 */
158 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	|\
159 				 BR_PS_16		|\
160 				 BR_V)
161 #define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
162 
163 /* NAND flash on CS2 */
164 #define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	|\
165 				 BR_PS_8		|\
166 				 BR_V)
167 #define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB		|\
168 				 OR_GPCM_BCTLD		|\
169 				 OR_GPCM_CSNT		|\
170 				 OR_GPCM_ACS_DIV4	|\
171 				 OR_GPCM_SCY_4		|\
172 				 OR_GPCM_TRLX		|\
173 				 OR_GPCM_EHTR)
174 
175 /* Optional NAND flash on CS3 */
176 #define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	|\
177 				 BR_PS_8		|\
178 				 BR_V)
179 #define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
180 
181 /*
182  * Use L1 as initial stack
183  */
184 #define CONFIG_SYS_INIT_RAM_LOCK	1
185 #define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
186 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
187 
188 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
189 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
190 
191 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
192 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
193 
194 /*
195  * Serial Port
196  */
197 #define CONFIG_CONS_INDEX		1
198 #define CONFIG_SYS_NS16550_SERIAL
199 #define CONFIG_SYS_NS16550_REG_SIZE	1
200 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
201 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
202 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
203 #define CONFIG_SYS_BAUDRATE_TABLE	\
204 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
205 #define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
206 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
207 
208 /*
209  * I2C
210  */
211 #define CONFIG_SYS_I2C
212 #define CONFIG_SYS_I2C_FSL
213 #define CONFIG_SYS_FSL_I2C_SPEED	100000
214 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
215 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
216 #define CONFIG_SYS_FSL_I2C2_SPEED	100000
217 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
218 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
219 
220 /* PEX8518 slave I2C interface */
221 #define CONFIG_SYS_I2C_PEX8518_ADDR	0x70
222 
223 /* I2C DS1631 temperature sensor */
224 #define CONFIG_SYS_I2C_LM90_ADDR	0x4c
225 
226 /* I2C EEPROM - AT24C128B */
227 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
228 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
229 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
230 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
231 
232 /* I2C RTC */
233 #define CONFIG_RTC_M41T11		1
234 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
235 #define CONFIG_SYS_M41T11_BASE_YEAR	2000
236 
237 /* GPIO */
238 #define CONFIG_PCA953X
239 #define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
240 #define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
241 #define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
242 #define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
243 #define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
244 #define CONFIG_SYS_I2C_PCA9553_ADDR	0x62
245 
246 /*
247  * PU = pulled high, PD = pulled low
248  * I = input, O = output, IO = input/output
249  */
250 /* PCA9557 @ 0x18*/
251 #define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
252 #define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select */
253 #define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
254 #define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select */
255 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
256 #define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Set to 0 to enable NVM writing */
257 
258 /* PCA9557 @ 0x1c*/
259 #define CONFIG_SYS_PCA953X_XMC0_ROOT0		0x01 /* PU; Low if XMC is RC */
260 #define CONFIG_SYS_PCA953X_PLUG_GPIO0		0x02 /* Samtec connector GPIO */
261 #define CONFIG_SYS_PCA953X_XMC0_WAKE		0x04 /* PU; XMC wake */
262 #define CONFIG_SYS_PCA953X_XMC0_BIST		0x08 /* PU; XMC built in self test */
263 #define CONFIG_SYS_PCA953X_XMC_PRESENT		0x10 /* PU; Low if XMC module installed */
264 #define CONFIG_SYS_PCA953X_PMC_PRESENT		0x20 /* PU; Low if PMC module installed */
265 #define CONFIG_SYS_PCA953X_PMC0_MONARCH		0x40 /* PMC monarch mode enable */
266 #define CONFIG_SYS_PCA953X_PMC0_EREADY		0x80 /* PU; PMC PCI eready */
267 
268 /* PCA9557 @ 0x1e*/
269 #define CONFIG_SYS_PCA953X_P0_GA0		0x01 /* PU; VPX Geographical address */
270 #define CONFIG_SYS_PCA953X_P0_GA1		0x02 /* PU; VPX Geographical address */
271 #define CONFIG_SYS_PCA953X_P0_GA2		0x04 /* PU; VPX Geographical address */
272 #define CONFIG_SYS_PCA953X_P0_GA3		0x08 /* PU; VPX Geographical address */
273 #define CONFIG_SYS_PCA953X_P0_GA4		0x10 /* PU; VPX Geographical address */
274 #define CONFIG_SYS_PCA953X_P0_GAP		0x20 /* PU; VPX Geographical address parity */
275 #define CONFIG_SYS_PCA953X_P1_SYSEN		0x80 /* PU; VPX P1 SYSCON */
276 
277 /* PCA9557 @ 0x1f */
278 #define CONFIG_SYS_PCA953X_VPX_GPIO0		0x01 /* PU; VPX P15 GPIO */
279 #define CONFIG_SYS_PCA953X_VPX_GPIO1		0x02 /* PU; VPX P15 GPIO */
280 #define CONFIG_SYS_PCA953X_VPX_GPIO2		0x04 /* PU; VPX P15 GPIO */
281 #define CONFIG_SYS_PCA953X_VPX_GPIO3		0x08 /* PU; VPX P15 GPIO */
282 
283 /*
284  * General PCI
285  * Memory space is mapped 1-1, but I/O space must start from 0.
286  */
287 /* PCIE1 - PEX8518 */
288 #define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
289 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
290 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
291 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
292 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
293 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
294 
295 /* PCIE2 - VPX P1 */
296 #define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
297 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
298 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
299 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
300 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
301 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
302 
303 /*
304  * Networking options
305  */
306 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
307 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
308 #define CONFIG_MII		1	/* MII PHY management */
309 #define CONFIG_ETHPRIME		"eTSEC1"
310 
311 #define CONFIG_TSEC1		1
312 #define CONFIG_TSEC1_NAME	"eTSEC1"
313 #define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
314 #define TSEC1_PHY_ADDR		1
315 #define TSEC1_PHYIDX		0
316 #define CONFIG_HAS_ETH0
317 
318 #define CONFIG_TSEC2		1
319 #define CONFIG_TSEC2_NAME	"eTSEC2"
320 #define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
321 #define TSEC2_PHY_ADDR		2
322 #define TSEC2_PHYIDX		0
323 #define CONFIG_HAS_ETH1
324 
325 /*
326  * BAT mappings
327  */
328 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
329 #define CONFIG_SYS_CCSR_DEFAULT_DBATL	(CONFIG_SYS_CCSRBAR_DEFAULT	|\
330 					 BATL_PP_RW			|\
331 					 BATL_CACHEINHIBIT		|\
332 					 BATL_GUARDEDSTORAGE)
333 #define CONFIG_SYS_CCSR_DEFAULT_DBATU	(CONFIG_SYS_CCSRBAR_DEFAULT	|\
334 					 BATU_BL_1M			|\
335 					 BATU_VS			|\
336 					 BATU_VP)
337 #define CONFIG_SYS_CCSR_DEFAULT_IBATL	(CONFIG_SYS_CCSRBAR_DEFAULT	|\
338 					 BATL_PP_RW			|\
339 					 BATL_CACHEINHIBIT)
340 #define CONFIG_SYS_CCSR_DEFAULT_IBATU	CONFIG_SYS_CCSR_DEFAULT_DBATU
341 #endif
342 
343 /*
344  * BAT0		2G	Cacheable, non-guarded
345  * 0x0000_0000	2G	DDR
346  */
347 #define CONFIG_SYS_DBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
348 #define CONFIG_SYS_DBAT0U	(BATU_BL_2G | BATU_VS | BATU_VP)
349 #define CONFIG_SYS_IBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
350 #define CONFIG_SYS_IBAT0U	CONFIG_SYS_DBAT0U
351 
352 /*
353  * BAT1		1G	Cache-inhibited, guarded
354  * 0x8000_0000	1G	PCI-Express 1 Memory
355  */
356 #define CONFIG_SYS_DBAT1L	(CONFIG_SYS_PCIE1_MEM_PHYS	|\
357 				 BATL_PP_RW			|\
358 				 BATL_CACHEINHIBIT		|\
359 				 BATL_GUARDEDSTORAGE)
360 #define CONFIG_SYS_DBAT1U	(CONFIG_SYS_PCIE1_MEM_PHYS	|\
361 				 BATU_BL_1G			|\
362 				 BATU_VS			|\
363 				 BATU_VP)
364 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCIE1_MEM_PHYS	|\
365 				 BATL_PP_RW			|\
366 				 BATL_CACHEINHIBIT)
367 #define CONFIG_SYS_IBAT1U	CONFIG_SYS_DBAT1U
368 
369 /*
370  * BAT2		512M	Cache-inhibited, guarded
371  * 0xc000_0000	512M	PCI-Express 2 Memory
372  */
373 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PCIE2_MEM_PHYS	|\
374 				 BATL_PP_RW			|\
375 				 BATL_CACHEINHIBIT		|\
376 				 BATL_GUARDEDSTORAGE)
377 #define CONFIG_SYS_DBAT2U	(CONFIG_SYS_PCIE2_MEM_PHYS	|\
378 				 BATU_BL_512M			|\
379 				 BATU_VS			|\
380 				 BATU_VP)
381 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCIE2_MEM_PHYS	|\
382 				 BATL_PP_RW			|\
383 				 BATL_CACHEINHIBIT)
384 #define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
385 
386 /*
387  * BAT3		1M	Cache-inhibited, guarded
388  * 0xe000_0000	1M	CCSR
389  */
390 #define CONFIG_SYS_DBAT3L	(CONFIG_SYS_CCSRBAR		|\
391 				 BATL_PP_RW			|\
392 				 BATL_CACHEINHIBIT		|\
393 				 BATL_GUARDEDSTORAGE)
394 #define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR		|\
395 				 BATU_BL_1M			|\
396 				 BATU_VS			|\
397 				 BATU_VP)
398 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR		|\
399 				 BATL_PP_RW			|\
400 				 BATL_CACHEINHIBIT)
401 #define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U
402 
403 /*
404  * BAT4		32M	Cache-inhibited, guarded
405  * 0xe200_0000	16M	PCI-Express 1 I/O
406  * 0xe300_0000	16M	PCI-Express 2 I/0
407  */
408 #define CONFIG_SYS_DBAT4L	(CONFIG_SYS_PCIE1_IO_PHYS	|\
409 				 BATL_PP_RW			|\
410 				 BATL_CACHEINHIBIT		|\
411 				 BATL_GUARDEDSTORAGE)
412 #define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCIE1_IO_PHYS	|\
413 				 BATU_BL_32M			|\
414 				 BATU_VS			|\
415 				 BATU_VP)
416 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCIE1_IO_PHYS	|\
417 				 BATL_PP_RW			|\
418 				 BATL_CACHEINHIBIT)
419 #define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U
420 
421 /*
422  * BAT5		128K	Cacheable, non-guarded
423  * 0xe400_1000	128K	Init RAM for stack in the CPU DCache (no backing memory)
424  */
425 #define CONFIG_SYS_DBAT5L	(CONFIG_SYS_INIT_RAM_ADDR	|\
426 				 BATL_PP_RW			|\
427 				 BATL_MEMCOHERENCE)
428 #define CONFIG_SYS_DBAT5U	(CONFIG_SYS_INIT_RAM_ADDR	|\
429 				 BATU_BL_128K			|\
430 				 BATU_VS			|\
431 				 BATU_VP)
432 #define CONFIG_SYS_IBAT5L	CONFIG_SYS_DBAT5L
433 #define CONFIG_SYS_IBAT5U	CONFIG_SYS_DBAT5U
434 
435 /*
436  * BAT6		256M	Cache-inhibited, guarded
437  * 0xf000_0000	256M	FLASH
438  */
439 #define CONFIG_SYS_DBAT6L	(CONFIG_SYS_FLASH_BASE2		|\
440 				 BATL_PP_RW			|\
441 				 BATL_CACHEINHIBIT		|\
442 				 BATL_GUARDEDSTORAGE)
443 #define CONFIG_SYS_DBAT6U	(CONFIG_SYS_FLASH_BASE		|\
444 				 BATU_BL_256M			|\
445 				 BATU_VS			|\
446 				 BATU_VP)
447 #define CONFIG_SYS_IBAT6L	(CONFIG_SYS_FLASH_BASE		|\
448 				 BATL_PP_RW			|\
449 				 BATL_MEMCOHERENCE)
450 #define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
451 
452 /* Map the last 1M of flash where we're running from reset */
453 #define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY	|\
454 				 BATL_PP_RW			|\
455 				 BATL_CACHEINHIBIT		|\
456 				 BATL_GUARDEDSTORAGE)
457 #define CONFIG_SYS_DBAT6U_EARLY	(CONFIG_SYS_TEXT_BASE			|\
458 				 BATU_BL_1M			|\
459 				 BATU_VS			|\
460 				 BATU_VP)
461 #define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY	|\
462 				 BATL_PP_RW			|\
463 				 BATL_MEMCOHERENCE)
464 #define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY
465 
466 /*
467  * BAT7		64M	Cache-inhibited, guarded
468  * 0xe800_0000	64K	NAND FLASH
469  * 0xe804_0000	128K	DUART Registers
470  */
471 #define CONFIG_SYS_DBAT7L	(CONFIG_SYS_NAND_BASE		|\
472 				 BATL_PP_RW			|\
473 				 BATL_CACHEINHIBIT		|\
474 				 BATL_GUARDEDSTORAGE)
475 #define CONFIG_SYS_DBAT7U 	(CONFIG_SYS_NAND_BASE		|\
476 				 BATU_BL_512K			|\
477 				 BATU_VS			|\
478 				 BATU_VP)
479 #define CONFIG_SYS_IBAT7L	(CONFIG_SYS_NAND_BASE		|\
480 				 BATL_PP_RW			|\
481 				 BATL_CACHEINHIBIT)
482 #define CONFIG_SYS_IBAT7U	CONFIG_SYS_DBAT7U
483 
484 /*
485  * Command configuration.
486  */
487 #define CONFIG_CMD_PCA953X
488 #define CONFIG_CMD_PCA953X_INFO
489 #define CONFIG_CMD_PCI
490 #define CONFIG_CMD_PCI_ENUM
491 #define CONFIG_CMD_REGINFO
492 
493 /*
494  * Miscellaneous configurable options
495  */
496 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
497 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
498 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
499 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
500 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
501 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
502 #define CONFIG_CMDLINE_EDITING	1		/* Command-line editing */
503 #define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
504 #define CONFIG_PANIC_HANG			/* do not reset board on panic */
505 #define CONFIG_PREBOOT				/* enable preboot variable */
506 #define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
507 
508 /*
509  * For booting Linux, the board info and command line data
510  * have to be in the first 16 MB of memory, since this is
511  * the maximum mapped by the Linux kernel during initialization.
512  */
513 #define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
514 #define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
515 
516 /*
517  * Environment Configuration
518  */
519 #define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
520 #define CONFIG_ENV_SIZE		0x8000
521 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
522 
523 /*
524  * Flash memory map:
525  * fffc0000 - ffffffff	Pri FDT (256KB)
526  * fff80000 - fffbffff	Pri U-Boot Environment (256 KB)
527  * fff00000 - fff7ffff	Pri U-Boot (512 KB)
528  * fef00000 - ffefffff	Pri OS image (16MB)
529  * f8000000 - feefffff	Pri OS Use/Filesystem (111MB)
530  *
531  * f7fc0000 - f7ffffff	Sec FDT (256KB)
532  * f7f80000 - f7fbffff	Sec U-Boot Environment (256 KB)
533  * f7f00000 - f7f7ffff	Sec U-Boot (512 KB)
534  * f6f00000 - f7efffff	Sec OS image (16MB)
535  * f0000000 - f6efffff	Sec OS Use/Filesystem (111MB)
536  */
537 #define CONFIG_UBOOT1_ENV_ADDR	__stringify(0xfff00000)
538 #define CONFIG_UBOOT2_ENV_ADDR	__stringify(0xf7f00000)
539 #define CONFIG_FDT1_ENV_ADDR	__stringify(0xfffc0000)
540 #define CONFIG_FDT2_ENV_ADDR	__stringify(0xf7fc0000)
541 #define CONFIG_OS1_ENV_ADDR	__stringify(0xfef00000)
542 #define CONFIG_OS2_ENV_ADDR	__stringify(0xf6f00000)
543 
544 #define CONFIG_PROG_UBOOT1						\
545 	"$download_cmd $loadaddr $ubootfile; "				\
546 	"if test $? -eq 0; then "					\
547 		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
548 		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
549 		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
550 		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
551 		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
552 		"if test $? -ne 0; then "				\
553 			"echo PROGRAM FAILED; "				\
554 		"else; "						\
555 			"echo PROGRAM SUCCEEDED; "			\
556 		"fi; "							\
557 	"else; "							\
558 		"echo DOWNLOAD FAILED; "				\
559 	"fi;"
560 
561 #define CONFIG_PROG_UBOOT2						\
562 	"$download_cmd $loadaddr $ubootfile; "				\
563 	"if test $? -eq 0; then "					\
564 		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
565 		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
566 		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
567 		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
568 		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
569 		"if test $? -ne 0; then "				\
570 			"echo PROGRAM FAILED; "				\
571 		"else; "						\
572 			"echo PROGRAM SUCCEEDED; "			\
573 		"fi; "							\
574 	"else; "							\
575 		"echo DOWNLOAD FAILED; "				\
576 	"fi;"
577 
578 #define CONFIG_BOOT_OS_NET						\
579 	"$download_cmd $osaddr $osfile; "				\
580 	"if test $? -eq 0; then "					\
581 		"if test -n $fdtaddr; then "				\
582 			"$download_cmd $fdtaddr $fdtfile; "		\
583 			"if test $? -eq 0; then "			\
584 				"bootm $osaddr - $fdtaddr; "		\
585 			"else; "					\
586 				"echo FDT DOWNLOAD FAILED; "		\
587 			"fi; "						\
588 		"else; "						\
589 			"bootm $osaddr; "				\
590 		"fi; "							\
591 	"else; "							\
592 		"echo OS DOWNLOAD FAILED; "				\
593 	"fi;"
594 
595 #define CONFIG_PROG_OS1							\
596 	"$download_cmd $osaddr $osfile; "				\
597 	"if test $? -eq 0; then "					\
598 		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
599 		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
600 		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
601 		"if test $? -ne 0; then "				\
602 			"echo OS PROGRAM FAILED; "			\
603 		"else; "						\
604 			"echo OS PROGRAM SUCCEEDED; "			\
605 		"fi; "							\
606 	"else; "							\
607 		"echo OS DOWNLOAD FAILED; "				\
608 	"fi;"
609 
610 #define CONFIG_PROG_OS2							\
611 	"$download_cmd $osaddr $osfile; "				\
612 	"if test $? -eq 0; then "					\
613 		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
614 		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
615 		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
616 		"if test $? -ne 0; then "				\
617 			"echo OS PROGRAM FAILED; "			\
618 		"else; "						\
619 			"echo OS PROGRAM SUCCEEDED; "			\
620 		"fi; "							\
621 	"else; "							\
622 		"echo OS DOWNLOAD FAILED; "				\
623 	"fi;"
624 
625 #define CONFIG_PROG_FDT1						\
626 	"$download_cmd $fdtaddr $fdtfile; "				\
627 	"if test $? -eq 0; then "					\
628 		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
629 		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
630 		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
631 		"if test $? -ne 0; then "				\
632 			"echo FDT PROGRAM FAILED; "			\
633 		"else; "						\
634 			"echo FDT PROGRAM SUCCEEDED; "			\
635 		"fi; "							\
636 	"else; "							\
637 		"echo FDT DOWNLOAD FAILED; "				\
638 	"fi;"
639 
640 #define CONFIG_PROG_FDT2						\
641 	"$download_cmd $fdtaddr $fdtfile; "				\
642 	"if test $? -eq 0; then "					\
643 		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
644 		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
645 		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
646 		"if test $? -ne 0; then "				\
647 			"echo FDT PROGRAM FAILED; "			\
648 		"else; "						\
649 			"echo FDT PROGRAM SUCCEEDED; "			\
650 		"fi; "							\
651 	"else; "							\
652 		"echo FDT DOWNLOAD FAILED; "				\
653 	"fi;"
654 
655 #define	CONFIG_EXTRA_ENV_SETTINGS					\
656 	"autoload=yes\0"						\
657 	"download_cmd=tftp\0"						\
658 	"console_args=console=ttyS0,115200\0"				\
659 	"root_args=root=/dev/nfs rw\0"					\
660 	"misc_args=ip=on\0"						\
661 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
662 	"bootfile=/home/user/file\0"					\
663 	"osfile=/home/user/board.uImage\0"				\
664 	"fdtfile=/home/user/board.dtb\0"				\
665 	"ubootfile=/home/user/u-boot.bin\0"				\
666 	"fdtaddr=0x1e00000\0"						\
667 	"osaddr=0x1000000\0"						\
668 	"loadaddr=0x1000000\0"						\
669 	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
670 	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
671 	"prog_os1="CONFIG_PROG_OS1"\0"					\
672 	"prog_os2="CONFIG_PROG_OS2"\0"					\
673 	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
674 	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
675 	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
676 	"bootcmd_flash1=run set_bootargs; "				\
677 		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
678 	"bootcmd_flash2=run set_bootargs; "				\
679 		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
680 	"bootcmd=run bootcmd_flash1\0"
681 #endif	/* __CONFIG_H */
682