1 /* 2 * Copyright 2009 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * xpedite517x board configuration file 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_MPC8641 1 /* MPC8641 specific */ 18 #define CONFIG_XPEDITE5140 1 /* MPC8641HPCN board specific */ 19 #define CONFIG_SYS_BOARD_NAME "XPedite5170" 20 #define CONFIG_SYS_FORM_3U_VPX 1 21 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 22 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 23 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 24 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 25 #define CONFIG_ALTIVEC 1 26 #define CONFIG_DISPLAY_BOARDINFO 27 28 #define CONFIG_SYS_TEXT_BASE 0xfff00000 29 30 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 31 #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ 32 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 33 #define CONFIG_PCIE1 1 /* PCIE controler 1 */ 34 #define CONFIG_PCIE2 1 /* PCIE controler 2 */ 35 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 36 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 37 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 38 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 39 40 /* 41 * DDR config 42 */ 43 #define CONFIG_SYS_FSL_DDR2 44 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 45 #define CONFIG_DDR_SPD 46 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 47 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 48 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 49 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 50 #define CONFIG_NUM_DDR_CONTROLLERS 2 51 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 52 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 53 #define CONFIG_DDR_ECC 54 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 55 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 56 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 57 #define CONFIG_VERY_BIG_RAM 58 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 59 60 /* 61 * virtual address to be used for temporary mappings. There 62 * should be 128k free at this VA. 63 */ 64 #define CONFIG_SYS_SCRATCH_VA 0xe0000000 65 66 #ifndef __ASSEMBLY__ 67 extern unsigned long get_board_sys_clk(unsigned long dummy); 68 #endif 69 70 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC86xx */ 71 72 /* 73 * L2CR setup 74 */ 75 #define CONFIG_SYS_L2 76 #define L2_INIT 0 77 #define L2_ENABLE (L2CR_L2E) 78 79 /* 80 * Base addresses -- Note these are effective addresses where the 81 * actual resources get mapped (not physical addresses) 82 */ 83 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 84 #define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ 85 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR 86 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 87 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 88 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR 89 90 /* 91 * Diagnostics 92 */ 93 #define CONFIG_SYS_ALT_MEMTEST 94 #define CONFIG_SYS_MEMTEST_START 0x10000000 95 #define CONFIG_SYS_MEMTEST_END 0x20000000 96 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\ 97 CONFIG_SYS_POST_I2C) 98 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ 99 CONFIG_SYS_I2C_DS4510_ADDR, \ 100 CONFIG_SYS_I2C_EEPROM_ADDR, \ 101 CONFIG_SYS_I2C_LM90_ADDR, \ 102 CONFIG_SYS_I2C_PCA9553_ADDR, \ 103 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 104 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 105 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 106 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 107 CONFIG_SYS_I2C_PEX8518_ADDR, \ 108 CONFIG_SYS_I2C_RTC_ADDR} 109 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */ 110 #define I2C_ADDR_IGNORE_LIST {0x50} 111 112 /* 113 * Memory map 114 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 115 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 116 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 117 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 118 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 119 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 120 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 121 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 122 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 123 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 124 */ 125 126 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) 127 128 /* 129 * NAND flash configuration 130 */ 131 #define CONFIG_SYS_NAND_BASE 0xef800000 132 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 133 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2} 134 #define CONFIG_SYS_MAX_NAND_DEVICE 2 135 #define CONFIG_NAND_ACTL 136 #define CONFIG_SYS_NAND_ACTL_ALE (1 << 14) /* C_LA14 */ 137 #define CONFIG_SYS_NAND_ACTL_CLE (1 << 15) /* C_LA15 */ 138 #define CONFIG_SYS_NAND_ACTL_NCE 0 /* NCE not controlled by ADDR */ 139 #define CONFIG_SYS_NAND_ACTL_DELAY 25 140 #define CONFIG_JFFS2_NAND 141 142 /* 143 * NOR flash configuration 144 */ 145 #define CONFIG_SYS_FLASH_BASE 0xf8000000 146 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 147 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 148 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 149 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 150 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 151 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 152 #define CONFIG_FLASH_CFI_DRIVER 153 #define CONFIG_SYS_FLASH_CFI 154 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 155 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff00000, 0xc0000}, \ 156 {0xf7f00000, 0xc0000} } 157 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 158 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 159 160 /* 161 * Chip select configuration 162 */ 163 /* NOR Flash 0 on CS0 */ 164 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ 165 BR_PS_16 |\ 166 BR_V) 167 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB |\ 168 OR_GPCM_CSNT |\ 169 OR_GPCM_XACS |\ 170 OR_GPCM_ACS_DIV2 |\ 171 OR_GPCM_SCY_8 |\ 172 OR_GPCM_TRLX |\ 173 OR_GPCM_EHTR |\ 174 OR_GPCM_EAD) 175 176 /* NOR Flash 1 on CS1 */ 177 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 |\ 178 BR_PS_16 |\ 179 BR_V) 180 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 181 182 /* NAND flash on CS2 */ 183 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE |\ 184 BR_PS_8 |\ 185 BR_V) 186 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB |\ 187 OR_GPCM_BCTLD |\ 188 OR_GPCM_CSNT |\ 189 OR_GPCM_ACS_DIV4 |\ 190 OR_GPCM_SCY_4 |\ 191 OR_GPCM_TRLX |\ 192 OR_GPCM_EHTR) 193 194 /* Optional NAND flash on CS3 */ 195 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 |\ 196 BR_PS_8 |\ 197 BR_V) 198 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 199 200 /* 201 * Use L1 as initial stack 202 */ 203 #define CONFIG_SYS_INIT_RAM_LOCK 1 204 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 205 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 206 207 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 208 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 209 210 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 211 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 212 213 /* 214 * Serial Port 215 */ 216 #define CONFIG_CONS_INDEX 1 217 #define CONFIG_SYS_NS16550 218 #define CONFIG_SYS_NS16550_SERIAL 219 #define CONFIG_SYS_NS16550_REG_SIZE 1 220 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 221 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 222 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 223 #define CONFIG_SYS_BAUDRATE_TABLE \ 224 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 225 #define CONFIG_BAUDRATE 115200 226 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 227 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 228 229 /* 230 * Use the HUSH parser 231 */ 232 #define CONFIG_SYS_HUSH_PARSER 233 234 /* 235 * Pass open firmware flat tree 236 */ 237 #define CONFIG_OF_LIBFDT 1 238 #define CONFIG_OF_BOARD_SETUP 1 239 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 240 241 /* 242 * I2C 243 */ 244 #define CONFIG_SYS_I2C 245 #define CONFIG_SYS_I2C_FSL 246 #define CONFIG_SYS_FSL_I2C_SPEED 100000 247 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 248 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 249 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 250 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 251 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 252 253 /* PEX8518 slave I2C interface */ 254 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 255 256 /* I2C DS1631 temperature sensor */ 257 #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 258 #define CONFIG_DTT_DS1621 259 #define CONFIG_DTT_SENSORS { 0 } 260 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 261 262 /* I2C EEPROM - AT24C128B */ 263 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 264 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 265 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 266 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 267 268 /* I2C RTC */ 269 #define CONFIG_RTC_M41T11 1 270 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 271 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 272 273 /* GPIO/EEPROM/SRAM */ 274 #define CONFIG_DS4510 275 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 276 277 /* GPIO */ 278 #define CONFIG_PCA953X 279 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 280 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 281 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 282 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 283 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 284 #define CONFIG_SYS_I2C_PCA9553_ADDR 0x62 285 286 /* 287 * PU = pulled high, PD = pulled low 288 * I = input, O = output, IO = input/output 289 */ 290 /* PCA9557 @ 0x18*/ 291 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 292 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 293 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 294 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 295 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 296 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 297 298 /* PCA9557 @ 0x1c*/ 299 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 300 #define CONFIG_SYS_PCA953X_PLUG_GPIO0 0x02 /* Samtec connector GPIO */ 301 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 302 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 303 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 304 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 305 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 306 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 307 308 /* PCA9557 @ 0x1e*/ 309 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 310 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 311 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 312 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 313 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 314 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; VPX Geographical address parity */ 315 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; VPX P1 SYSCON */ 316 317 /* PCA9557 @ 0x1f */ 318 #define CONFIG_SYS_PCA953X_VPX_GPIO0 0x01 /* PU; VPX P15 GPIO */ 319 #define CONFIG_SYS_PCA953X_VPX_GPIO1 0x02 /* PU; VPX P15 GPIO */ 320 #define CONFIG_SYS_PCA953X_VPX_GPIO2 0x04 /* PU; VPX P15 GPIO */ 321 #define CONFIG_SYS_PCA953X_VPX_GPIO3 0x08 /* PU; VPX P15 GPIO */ 322 323 /* 324 * General PCI 325 * Memory space is mapped 1-1, but I/O space must start from 0. 326 */ 327 /* PCIE1 - PEX8518 */ 328 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 329 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 330 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 331 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 332 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 333 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 334 335 /* PCIE2 - VPX P1 */ 336 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 337 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 338 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 339 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 340 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 341 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 342 343 /* 344 * Networking options 345 */ 346 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 347 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 348 #define CONFIG_MII 1 /* MII PHY management */ 349 #define CONFIG_ETHPRIME "eTSEC1" 350 351 #define CONFIG_TSEC1 1 352 #define CONFIG_TSEC1_NAME "eTSEC1" 353 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 354 #define TSEC1_PHY_ADDR 1 355 #define TSEC1_PHYIDX 0 356 #define CONFIG_HAS_ETH0 357 358 #define CONFIG_TSEC2 1 359 #define CONFIG_TSEC2_NAME "eTSEC2" 360 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 361 #define TSEC2_PHY_ADDR 2 362 #define TSEC2_PHYIDX 0 363 #define CONFIG_HAS_ETH1 364 365 /* 366 * BAT mappings 367 */ 368 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 369 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ 370 BATL_PP_RW |\ 371 BATL_CACHEINHIBIT |\ 372 BATL_GUARDEDSTORAGE) 373 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT |\ 374 BATU_BL_1M |\ 375 BATU_VS |\ 376 BATU_VP) 377 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ 378 BATL_PP_RW |\ 379 BATL_CACHEINHIBIT) 380 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 381 #endif 382 383 /* 384 * BAT0 2G Cacheable, non-guarded 385 * 0x0000_0000 2G DDR 386 */ 387 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 388 #define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) 389 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 390 #define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U 391 392 /* 393 * BAT1 1G Cache-inhibited, guarded 394 * 0x8000_0000 1G PCI-Express 1 Memory 395 */ 396 #define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ 397 BATL_PP_RW |\ 398 BATL_CACHEINHIBIT |\ 399 BATL_GUARDEDSTORAGE) 400 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_PHYS |\ 401 BATU_BL_1G |\ 402 BATU_VS |\ 403 BATU_VP) 404 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ 405 BATL_PP_RW |\ 406 BATL_CACHEINHIBIT) 407 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 408 409 /* 410 * BAT2 512M Cache-inhibited, guarded 411 * 0xc000_0000 512M PCI-Express 2 Memory 412 */ 413 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ 414 BATL_PP_RW |\ 415 BATL_CACHEINHIBIT |\ 416 BATL_GUARDEDSTORAGE) 417 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE2_MEM_PHYS |\ 418 BATU_BL_512M |\ 419 BATU_VS |\ 420 BATU_VP) 421 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ 422 BATL_PP_RW |\ 423 BATL_CACHEINHIBIT) 424 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 425 426 /* 427 * BAT3 1M Cache-inhibited, guarded 428 * 0xe000_0000 1M CCSR 429 */ 430 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR |\ 431 BATL_PP_RW |\ 432 BATL_CACHEINHIBIT |\ 433 BATL_GUARDEDSTORAGE) 434 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR |\ 435 BATU_BL_1M |\ 436 BATU_VS |\ 437 BATU_VP) 438 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR |\ 439 BATL_PP_RW |\ 440 BATL_CACHEINHIBIT) 441 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 442 443 /* 444 * BAT4 32M Cache-inhibited, guarded 445 * 0xe200_0000 16M PCI-Express 1 I/O 446 * 0xe300_0000 16M PCI-Express 2 I/0 447 */ 448 #define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ 449 BATL_PP_RW |\ 450 BATL_CACHEINHIBIT |\ 451 BATL_GUARDEDSTORAGE) 452 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_PHYS |\ 453 BATU_BL_32M |\ 454 BATU_VS |\ 455 BATU_VP) 456 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ 457 BATL_PP_RW |\ 458 BATL_CACHEINHIBIT) 459 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 460 461 /* 462 * BAT5 128K Cacheable, non-guarded 463 * 0xe400_1000 128K Init RAM for stack in the CPU DCache (no backing memory) 464 */ 465 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR |\ 466 BATL_PP_RW |\ 467 BATL_MEMCOHERENCE) 468 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR |\ 469 BATU_BL_128K |\ 470 BATU_VS |\ 471 BATU_VP) 472 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 473 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 474 475 /* 476 * BAT6 256M Cache-inhibited, guarded 477 * 0xf000_0000 256M FLASH 478 */ 479 #define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE2 |\ 480 BATL_PP_RW |\ 481 BATL_CACHEINHIBIT |\ 482 BATL_GUARDEDSTORAGE) 483 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE |\ 484 BATU_BL_256M |\ 485 BATU_VS |\ 486 BATU_VP) 487 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE |\ 488 BATL_PP_RW |\ 489 BATL_MEMCOHERENCE) 490 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 491 492 /* Map the last 1M of flash where we're running from reset */ 493 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ 494 BATL_PP_RW |\ 495 BATL_CACHEINHIBIT |\ 496 BATL_GUARDEDSTORAGE) 497 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE |\ 498 BATU_BL_1M |\ 499 BATU_VS |\ 500 BATU_VP) 501 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ 502 BATL_PP_RW |\ 503 BATL_MEMCOHERENCE) 504 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 505 506 /* 507 * BAT7 64M Cache-inhibited, guarded 508 * 0xe800_0000 64K NAND FLASH 509 * 0xe804_0000 128K DUART Registers 510 */ 511 #define CONFIG_SYS_DBAT7L (CONFIG_SYS_NAND_BASE |\ 512 BATL_PP_RW |\ 513 BATL_CACHEINHIBIT |\ 514 BATL_GUARDEDSTORAGE) 515 #define CONFIG_SYS_DBAT7U (CONFIG_SYS_NAND_BASE |\ 516 BATU_BL_512K |\ 517 BATU_VS |\ 518 BATU_VP) 519 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_NAND_BASE |\ 520 BATL_PP_RW |\ 521 BATL_CACHEINHIBIT) 522 #define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U 523 524 /* 525 * Command configuration. 526 */ 527 #define CONFIG_CMD_ASKENV 528 #define CONFIG_CMD_DATE 529 #define CONFIG_CMD_DHCP 530 #define CONFIG_CMD_DS4510 531 #define CONFIG_CMD_DS4510_INFO 532 #define CONFIG_CMD_DTT 533 #define CONFIG_CMD_EEPROM 534 #define CONFIG_CMD_I2C 535 #define CONFIG_CMD_IRQ 536 #define CONFIG_CMD_JFFS2 537 #define CONFIG_CMD_MII 538 #define CONFIG_CMD_NAND 539 #define CONFIG_CMD_PCA953X 540 #define CONFIG_CMD_PCA953X_INFO 541 #define CONFIG_CMD_PCI 542 #define CONFIG_CMD_PCI_ENUM 543 #define CONFIG_CMD_PING 544 #define CONFIG_CMD_REGINFO 545 #define CONFIG_CMD_SNTP 546 547 /* 548 * Miscellaneous configurable options 549 */ 550 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 551 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 552 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 553 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 554 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 555 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 556 #define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */ 557 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 558 #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ 559 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 560 #define CONFIG_PREBOOT /* enable preboot variable */ 561 #define CONFIG_FIT 1 562 #define CONFIG_FIT_VERBOSE 1 563 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 564 565 /* 566 * For booting Linux, the board info and command line data 567 * have to be in the first 16 MB of memory, since this is 568 * the maximum mapped by the Linux kernel during initialization. 569 */ 570 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 571 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 572 573 /* 574 * Environment Configuration 575 */ 576 #define CONFIG_ENV_IS_IN_FLASH 1 577 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 578 #define CONFIG_ENV_SIZE 0x8000 579 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 580 581 /* 582 * Flash memory map: 583 * fffc0000 - ffffffff Pri FDT (256KB) 584 * fff80000 - fffbffff Pri U-Boot Environment (256 KB) 585 * fff00000 - fff7ffff Pri U-Boot (512 KB) 586 * fef00000 - ffefffff Pri OS image (16MB) 587 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 588 * 589 * f7fc0000 - f7ffffff Sec FDT (256KB) 590 * f7f80000 - f7fbffff Sec U-Boot Environment (256 KB) 591 * f7f00000 - f7f7ffff Sec U-Boot (512 KB) 592 * f6f00000 - f7efffff Sec OS image (16MB) 593 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 594 */ 595 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff00000) 596 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f00000) 597 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfffc0000) 598 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7fc0000) 599 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 600 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 601 602 #define CONFIG_PROG_UBOOT1 \ 603 "$download_cmd $loadaddr $ubootfile; " \ 604 "if test $? -eq 0; then " \ 605 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 606 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 607 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 608 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 609 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 610 "if test $? -ne 0; then " \ 611 "echo PROGRAM FAILED; " \ 612 "else; " \ 613 "echo PROGRAM SUCCEEDED; " \ 614 "fi; " \ 615 "else; " \ 616 "echo DOWNLOAD FAILED; " \ 617 "fi;" 618 619 #define CONFIG_PROG_UBOOT2 \ 620 "$download_cmd $loadaddr $ubootfile; " \ 621 "if test $? -eq 0; then " \ 622 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 623 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 624 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 625 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 626 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 627 "if test $? -ne 0; then " \ 628 "echo PROGRAM FAILED; " \ 629 "else; " \ 630 "echo PROGRAM SUCCEEDED; " \ 631 "fi; " \ 632 "else; " \ 633 "echo DOWNLOAD FAILED; " \ 634 "fi;" 635 636 #define CONFIG_BOOT_OS_NET \ 637 "$download_cmd $osaddr $osfile; " \ 638 "if test $? -eq 0; then " \ 639 "if test -n $fdtaddr; then " \ 640 "$download_cmd $fdtaddr $fdtfile; " \ 641 "if test $? -eq 0; then " \ 642 "bootm $osaddr - $fdtaddr; " \ 643 "else; " \ 644 "echo FDT DOWNLOAD FAILED; " \ 645 "fi; " \ 646 "else; " \ 647 "bootm $osaddr; " \ 648 "fi; " \ 649 "else; " \ 650 "echo OS DOWNLOAD FAILED; " \ 651 "fi;" 652 653 #define CONFIG_PROG_OS1 \ 654 "$download_cmd $osaddr $osfile; " \ 655 "if test $? -eq 0; then " \ 656 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 657 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 658 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 659 "if test $? -ne 0; then " \ 660 "echo OS PROGRAM FAILED; " \ 661 "else; " \ 662 "echo OS PROGRAM SUCCEEDED; " \ 663 "fi; " \ 664 "else; " \ 665 "echo OS DOWNLOAD FAILED; " \ 666 "fi;" 667 668 #define CONFIG_PROG_OS2 \ 669 "$download_cmd $osaddr $osfile; " \ 670 "if test $? -eq 0; then " \ 671 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 672 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 673 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 674 "if test $? -ne 0; then " \ 675 "echo OS PROGRAM FAILED; " \ 676 "else; " \ 677 "echo OS PROGRAM SUCCEEDED; " \ 678 "fi; " \ 679 "else; " \ 680 "echo OS DOWNLOAD FAILED; " \ 681 "fi;" 682 683 #define CONFIG_PROG_FDT1 \ 684 "$download_cmd $fdtaddr $fdtfile; " \ 685 "if test $? -eq 0; then " \ 686 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 687 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 688 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 689 "if test $? -ne 0; then " \ 690 "echo FDT PROGRAM FAILED; " \ 691 "else; " \ 692 "echo FDT PROGRAM SUCCEEDED; " \ 693 "fi; " \ 694 "else; " \ 695 "echo FDT DOWNLOAD FAILED; " \ 696 "fi;" 697 698 #define CONFIG_PROG_FDT2 \ 699 "$download_cmd $fdtaddr $fdtfile; " \ 700 "if test $? -eq 0; then " \ 701 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 702 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 703 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 704 "if test $? -ne 0; then " \ 705 "echo FDT PROGRAM FAILED; " \ 706 "else; " \ 707 "echo FDT PROGRAM SUCCEEDED; " \ 708 "fi; " \ 709 "else; " \ 710 "echo FDT DOWNLOAD FAILED; " \ 711 "fi;" 712 713 #define CONFIG_EXTRA_ENV_SETTINGS \ 714 "autoload=yes\0" \ 715 "download_cmd=tftp\0" \ 716 "console_args=console=ttyS0,115200\0" \ 717 "root_args=root=/dev/nfs rw\0" \ 718 "misc_args=ip=on\0" \ 719 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 720 "bootfile=/home/user/file\0" \ 721 "osfile=/home/user/board.uImage\0" \ 722 "fdtfile=/home/user/board.dtb\0" \ 723 "ubootfile=/home/user/u-boot.bin\0" \ 724 "fdtaddr=c00000\0" \ 725 "osaddr=0x1000000\0" \ 726 "loadaddr=0x1000000\0" \ 727 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 728 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 729 "prog_os1="CONFIG_PROG_OS1"\0" \ 730 "prog_os2="CONFIG_PROG_OS2"\0" \ 731 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 732 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 733 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 734 "bootcmd_flash1=run set_bootargs; " \ 735 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 736 "bootcmd_flash2=run set_bootargs; " \ 737 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 738 "bootcmd=run bootcmd_flash1\0" 739 #endif /* __CONFIG_H */ 740