1 /* 2 * Copyright 2009 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 21 * MA 02111-1307 USA 22 */ 23 24 /* 25 * xpedite517x board configuration file 26 */ 27 #ifndef __CONFIG_H 28 #define __CONFIG_H 29 30 /* 31 * High Level Configuration Options 32 */ 33 #define CONFIG_MPC86xx 1 /* MPC86xx */ 34 #define CONFIG_MPC8641 1 /* MPC8641 specific */ 35 #define CONFIG_XPEDITE5140 1 /* MPC8641HPCN board specific */ 36 #define CONFIG_SYS_BOARD_NAME "XPedite5170" 37 #define CONFIG_SYS_FORM_3U_VPX 1 38 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 39 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 40 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 41 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 42 #define CONFIG_ALTIVEC 1 43 44 #define CONFIG_SYS_TEXT_BASE 0xfff00000 45 46 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 47 #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ 48 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 49 #define CONFIG_PCIE1 1 /* PCIE controler 1 */ 50 #define CONFIG_PCIE2 1 /* PCIE controler 2 */ 51 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 52 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 53 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 54 55 /* 56 * DDR config 57 */ 58 #define CONFIG_FSL_DDR2 59 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 60 #define CONFIG_DDR_SPD 61 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 62 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ 63 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ 64 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 65 #define CONFIG_NUM_DDR_CONTROLLERS 2 66 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 67 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 68 #define CONFIG_DDR_ECC 69 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 70 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 71 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 72 #define CONFIG_VERY_BIG_RAM 73 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 74 75 /* 76 * virtual address to be used for temporary mappings. There 77 * should be 128k free at this VA. 78 */ 79 #define CONFIG_SYS_SCRATCH_VA 0xe0000000 80 81 #ifndef __ASSEMBLY__ 82 extern unsigned long get_board_sys_clk(unsigned long dummy); 83 #endif 84 85 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC86xx */ 86 87 /* 88 * L2CR setup 89 */ 90 #define CONFIG_SYS_L2 91 #define L2_INIT 0 92 #define L2_ENABLE (L2CR_L2E) 93 94 /* 95 * Base addresses -- Note these are effective addresses where the 96 * actual resources get mapped (not physical addresses) 97 */ 98 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 99 #define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ 100 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR 101 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 102 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 103 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR 104 105 /* 106 * Diagnostics 107 */ 108 #define CONFIG_SYS_ALT_MEMTEST 109 #define CONFIG_SYS_MEMTEST_START 0x10000000 110 #define CONFIG_SYS_MEMTEST_END 0x20000000 111 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\ 112 CONFIG_SYS_POST_I2C) 113 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ 114 CONFIG_SYS_I2C_DS4510_ADDR, \ 115 CONFIG_SYS_I2C_EEPROM_ADDR, \ 116 CONFIG_SYS_I2C_LM90_ADDR, \ 117 CONFIG_SYS_I2C_PCA9553_ADDR, \ 118 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 119 CONFIG_SYS_I2C_PCA953X_ADDR1, \ 120 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 121 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 122 CONFIG_SYS_I2C_PEX8518_ADDR, \ 123 CONFIG_SYS_I2C_RTC_ADDR} 124 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */ 125 #define I2C_ADDR_IGNORE_LIST {0x50} 126 127 /* 128 * Memory map 129 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 130 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 131 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable 132 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 133 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 134 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable 135 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 136 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 137 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 138 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 139 */ 140 141 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) 142 143 /* 144 * NAND flash configuration 145 */ 146 #define CONFIG_SYS_NAND_BASE 0xef800000 147 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 148 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2} 149 #define CONFIG_SYS_MAX_NAND_DEVICE 2 150 #define CONFIG_NAND_ACTL 151 #define CONFIG_SYS_NAND_ACTL_ALE (1 << 14) /* C_LA14 */ 152 #define CONFIG_SYS_NAND_ACTL_CLE (1 << 15) /* C_LA15 */ 153 #define CONFIG_SYS_NAND_ACTL_NCE 0 /* NCE not controlled by ADDR */ 154 #define CONFIG_SYS_NAND_ACTL_DELAY 25 155 #define CONFIG_SYS_NAND_QUIET_TEST 156 #define CONFIG_JFFS2_NAND 157 158 /* 159 * NOR flash configuration 160 */ 161 #define CONFIG_SYS_FLASH_BASE 0xf8000000 162 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 163 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 164 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 165 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 166 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 167 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 168 #define CONFIG_FLASH_CFI_DRIVER 169 #define CONFIG_SYS_FLASH_CFI 170 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 171 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff00000, 0xc0000}, \ 172 {0xf7f00000, 0xc0000} } 173 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 174 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 175 176 /* 177 * Chip select configuration 178 */ 179 /* NOR Flash 0 on CS0 */ 180 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ 181 BR_PS_16 |\ 182 BR_V) 183 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB |\ 184 OR_GPCM_CSNT |\ 185 OR_GPCM_XACS |\ 186 OR_GPCM_ACS_DIV2 |\ 187 OR_GPCM_SCY_8 |\ 188 OR_GPCM_TRLX |\ 189 OR_GPCM_EHTR |\ 190 OR_GPCM_EAD) 191 192 /* NOR Flash 1 on CS1 */ 193 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 |\ 194 BR_PS_16 |\ 195 BR_V) 196 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 197 198 /* NAND flash on CS2 */ 199 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE |\ 200 BR_PS_8 |\ 201 BR_V) 202 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB |\ 203 OR_GPCM_BCTLD |\ 204 OR_GPCM_CSNT |\ 205 OR_GPCM_ACS_DIV4 |\ 206 OR_GPCM_SCY_4 |\ 207 OR_GPCM_TRLX |\ 208 OR_GPCM_EHTR) 209 210 /* Optional NAND flash on CS3 */ 211 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 |\ 212 BR_PS_8 |\ 213 BR_V) 214 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 215 216 /* 217 * Use L1 as initial stack 218 */ 219 #define CONFIG_SYS_INIT_RAM_LOCK 1 220 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 221 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 222 223 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 224 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 225 226 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 227 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 228 229 /* 230 * Serial Port 231 */ 232 #define CONFIG_CONS_INDEX 1 233 #define CONFIG_SYS_NS16550 234 #define CONFIG_SYS_NS16550_SERIAL 235 #define CONFIG_SYS_NS16550_REG_SIZE 1 236 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 237 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 238 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 239 #define CONFIG_SYS_BAUDRATE_TABLE \ 240 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 241 #define CONFIG_BAUDRATE 115200 242 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 243 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 244 245 /* 246 * Use the HUSH parser 247 */ 248 #define CONFIG_SYS_HUSH_PARSER 249 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 250 251 /* 252 * Pass open firmware flat tree 253 */ 254 #define CONFIG_OF_LIBFDT 1 255 #define CONFIG_OF_BOARD_SETUP 1 256 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 257 258 /* 259 * I2C 260 */ 261 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 262 #define CONFIG_HARD_I2C /* I2C with hardware support */ 263 #define CONFIG_SYS_I2C_SPEED 100000 /* M41T00 only supports 100 KHz */ 264 #define CONFIG_SYS_I2C_SLAVE 0x7F 265 #define CONFIG_SYS_I2C_OFFSET 0x3000 266 #define CONFIG_SYS_I2C2_OFFSET 0x3100 267 #define CONFIG_I2C_MULTI_BUS 268 269 /* PEX8518 slave I2C interface */ 270 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 271 272 /* I2C DS1631 temperature sensor */ 273 #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 274 #define CONFIG_DTT_DS1621 275 #define CONFIG_DTT_SENSORS { 0 } 276 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c 277 278 /* I2C EEPROM - AT24C128B */ 279 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 280 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 281 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 282 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 283 284 /* I2C RTC */ 285 #define CONFIG_RTC_M41T11 1 286 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 287 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 288 289 /* GPIO/EEPROM/SRAM */ 290 #define CONFIG_DS4510 291 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 292 293 /* GPIO */ 294 #define CONFIG_PCA953X 295 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 296 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 297 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 298 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 299 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 300 #define CONFIG_SYS_I2C_PCA9553_ADDR 0x62 301 302 /* 303 * PU = pulled high, PD = pulled low 304 * I = input, O = output, IO = input/output 305 */ 306 /* PCA9557 @ 0x18*/ 307 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 308 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ 309 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 310 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ 311 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 312 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ 313 314 /* PCA9557 @ 0x1c*/ 315 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ 316 #define CONFIG_SYS_PCA953X_PLUG_GPIO0 0x02 /* Samtec connector GPIO */ 317 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ 318 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ 319 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ 320 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ 321 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ 322 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ 323 324 /* PCA9557 @ 0x1e*/ 325 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ 326 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ 327 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ 328 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ 329 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ 330 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; VPX Geographical address parity */ 331 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; VPX P1 SYSCON */ 332 333 /* PCA9557 @ 0x1f */ 334 #define CONFIG_SYS_PCA953X_VPX_GPIO0 0x01 /* PU; VPX P15 GPIO */ 335 #define CONFIG_SYS_PCA953X_VPX_GPIO1 0x02 /* PU; VPX P15 GPIO */ 336 #define CONFIG_SYS_PCA953X_VPX_GPIO2 0x04 /* PU; VPX P15 GPIO */ 337 #define CONFIG_SYS_PCA953X_VPX_GPIO3 0x08 /* PU; VPX P15 GPIO */ 338 339 /* 340 * General PCI 341 * Memory space is mapped 1-1, but I/O space must start from 0. 342 */ 343 /* PCIE1 - PEX8518 */ 344 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 345 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 346 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 347 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 348 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 349 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 350 351 /* PCIE2 - VPX P1 */ 352 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 353 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 354 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 355 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 356 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 357 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ 358 359 /* 360 * Networking options 361 */ 362 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 363 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 364 #define CONFIG_NET_MULTI 1 365 #define CONFIG_MII 1 /* MII PHY management */ 366 #define CONFIG_ETHPRIME "eTSEC1" 367 368 #define CONFIG_TSEC1 1 369 #define CONFIG_TSEC1_NAME "eTSEC1" 370 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 371 #define TSEC1_PHY_ADDR 1 372 #define TSEC1_PHYIDX 0 373 #define CONFIG_HAS_ETH0 374 375 #define CONFIG_TSEC2 1 376 #define CONFIG_TSEC2_NAME "eTSEC2" 377 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 378 #define TSEC2_PHY_ADDR 2 379 #define TSEC2_PHYIDX 0 380 #define CONFIG_HAS_ETH1 381 382 /* 383 * BAT mappings 384 */ 385 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 386 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ 387 BATL_PP_RW |\ 388 BATL_CACHEINHIBIT |\ 389 BATL_GUARDEDSTORAGE) 390 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT |\ 391 BATU_BL_1M |\ 392 BATU_VS |\ 393 BATU_VP) 394 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ 395 BATL_PP_RW |\ 396 BATL_CACHEINHIBIT) 397 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 398 #endif 399 400 /* 401 * BAT0 2G Cacheable, non-guarded 402 * 0x0000_0000 2G DDR 403 */ 404 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 405 #define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) 406 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 407 #define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U 408 409 /* 410 * BAT1 1G Cache-inhibited, guarded 411 * 0x8000_0000 1G PCI-Express 1 Memory 412 */ 413 #define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ 414 BATL_PP_RW |\ 415 BATL_CACHEINHIBIT |\ 416 BATL_GUARDEDSTORAGE) 417 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_PHYS |\ 418 BATU_BL_1G |\ 419 BATU_VS |\ 420 BATU_VP) 421 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ 422 BATL_PP_RW |\ 423 BATL_CACHEINHIBIT) 424 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 425 426 /* 427 * BAT2 512M Cache-inhibited, guarded 428 * 0xc000_0000 512M PCI-Express 2 Memory 429 */ 430 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ 431 BATL_PP_RW |\ 432 BATL_CACHEINHIBIT |\ 433 BATL_GUARDEDSTORAGE) 434 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE2_MEM_PHYS |\ 435 BATU_BL_512M |\ 436 BATU_VS |\ 437 BATU_VP) 438 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ 439 BATL_PP_RW |\ 440 BATL_CACHEINHIBIT) 441 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 442 443 /* 444 * BAT3 1M Cache-inhibited, guarded 445 * 0xe000_0000 1M CCSR 446 */ 447 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR |\ 448 BATL_PP_RW |\ 449 BATL_CACHEINHIBIT |\ 450 BATL_GUARDEDSTORAGE) 451 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR |\ 452 BATU_BL_1M |\ 453 BATU_VS |\ 454 BATU_VP) 455 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR |\ 456 BATL_PP_RW |\ 457 BATL_CACHEINHIBIT) 458 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 459 460 /* 461 * BAT4 32M Cache-inhibited, guarded 462 * 0xe200_0000 16M PCI-Express 1 I/O 463 * 0xe300_0000 16M PCI-Express 2 I/0 464 */ 465 #define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ 466 BATL_PP_RW |\ 467 BATL_CACHEINHIBIT |\ 468 BATL_GUARDEDSTORAGE) 469 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_PHYS |\ 470 BATU_BL_32M |\ 471 BATU_VS |\ 472 BATU_VP) 473 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ 474 BATL_PP_RW |\ 475 BATL_CACHEINHIBIT) 476 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 477 478 /* 479 * BAT5 128K Cacheable, non-guarded 480 * 0xe400_1000 128K Init RAM for stack in the CPU DCache (no backing memory) 481 */ 482 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR |\ 483 BATL_PP_RW |\ 484 BATL_MEMCOHERENCE) 485 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR |\ 486 BATU_BL_128K |\ 487 BATU_VS |\ 488 BATU_VP) 489 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 490 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 491 492 /* 493 * BAT6 256M Cache-inhibited, guarded 494 * 0xf000_0000 256M FLASH 495 */ 496 #define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE2 |\ 497 BATL_PP_RW |\ 498 BATL_CACHEINHIBIT |\ 499 BATL_GUARDEDSTORAGE) 500 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE |\ 501 BATU_BL_256M |\ 502 BATU_VS |\ 503 BATU_VP) 504 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE |\ 505 BATL_PP_RW |\ 506 BATL_MEMCOHERENCE) 507 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 508 509 /* Map the last 1M of flash where we're running from reset */ 510 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ 511 BATL_PP_RW |\ 512 BATL_CACHEINHIBIT |\ 513 BATL_GUARDEDSTORAGE) 514 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE |\ 515 BATU_BL_1M |\ 516 BATU_VS |\ 517 BATU_VP) 518 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ 519 BATL_PP_RW |\ 520 BATL_MEMCOHERENCE) 521 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 522 523 /* 524 * BAT7 64M Cache-inhibited, guarded 525 * 0xe800_0000 64K NAND FLASH 526 * 0xe804_0000 128K DUART Registers 527 */ 528 #define CONFIG_SYS_DBAT7L (CONFIG_SYS_NAND_BASE |\ 529 BATL_PP_RW |\ 530 BATL_CACHEINHIBIT |\ 531 BATL_GUARDEDSTORAGE) 532 #define CONFIG_SYS_DBAT7U (CONFIG_SYS_NAND_BASE |\ 533 BATU_BL_512K |\ 534 BATU_VS |\ 535 BATU_VP) 536 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_NAND_BASE |\ 537 BATL_PP_RW |\ 538 BATL_CACHEINHIBIT) 539 #define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U 540 541 /* 542 * Command configuration. 543 */ 544 #include <config_cmd_default.h> 545 546 #define CONFIG_CMD_ASKENV 547 #define CONFIG_CMD_DATE 548 #define CONFIG_CMD_DHCP 549 #define CONFIG_CMD_DS4510 550 #define CONFIG_CMD_DS4510_INFO 551 #define CONFIG_CMD_DTT 552 #define CONFIG_CMD_EEPROM 553 #define CONFIG_CMD_ELF 554 #define CONFIG_CMD_SAVEENV 555 #define CONFIG_CMD_FLASH 556 #define CONFIG_CMD_I2C 557 #define CONFIG_CMD_IRQ 558 #define CONFIG_CMD_JFFS2 559 #define CONFIG_CMD_MII 560 #define CONFIG_CMD_NAND 561 #define CONFIG_CMD_NET 562 #define CONFIG_CMD_PCA953X 563 #define CONFIG_CMD_PCA953X_INFO 564 #define CONFIG_CMD_PCI 565 #define CONFIG_CMD_PCI_ENUM 566 #define CONFIG_CMD_PING 567 #define CONFIG_CMD_REGINFO 568 #define CONFIG_CMD_SNTP 569 570 /* 571 * Miscellaneous configurable options 572 */ 573 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 574 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 575 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 576 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 577 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 578 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 579 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 580 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 581 #define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */ 582 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 583 #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ 584 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 585 #define CONFIG_PREBOOT /* enable preboot variable */ 586 #define CONFIG_FIT 1 587 #define CONFIG_FIT_VERBOSE 1 588 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 589 590 /* 591 * For booting Linux, the board info and command line data 592 * have to be in the first 16 MB of memory, since this is 593 * the maximum mapped by the Linux kernel during initialization. 594 */ 595 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 596 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 597 598 /* 599 * Environment Configuration 600 */ 601 #define CONFIG_ENV_IS_IN_FLASH 1 602 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 603 #define CONFIG_ENV_SIZE 0x8000 604 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 605 606 /* 607 * Flash memory map: 608 * fffc0000 - ffffffff Pri FDT (256KB) 609 * fff80000 - fffbffff Pri U-Boot Environment (256 KB) 610 * fff00000 - fff7ffff Pri U-Boot (512 KB) 611 * fef00000 - ffefffff Pri OS image (16MB) 612 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 613 * 614 * f7fc0000 - f7ffffff Sec FDT (256KB) 615 * f7f80000 - f7fbffff Sec U-Boot Environment (256 KB) 616 * f7f00000 - f7f7ffff Sec U-Boot (512 KB) 617 * f6f00000 - f7efffff Sec OS image (16MB) 618 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 619 */ 620 #define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff00000) 621 #define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f00000) 622 #define CONFIG_FDT1_ENV_ADDR MK_STR(0xfffc0000) 623 #define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7fc0000) 624 #define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) 625 #define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000) 626 627 #define CONFIG_PROG_UBOOT1 \ 628 "$download_cmd $loadaddr $ubootfile; " \ 629 "if test $? -eq 0; then " \ 630 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 631 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 632 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 633 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 634 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 635 "if test $? -ne 0; then " \ 636 "echo PROGRAM FAILED; " \ 637 "else; " \ 638 "echo PROGRAM SUCCEEDED; " \ 639 "fi; " \ 640 "else; " \ 641 "echo DOWNLOAD FAILED; " \ 642 "fi;" 643 644 #define CONFIG_PROG_UBOOT2 \ 645 "$download_cmd $loadaddr $ubootfile; " \ 646 "if test $? -eq 0; then " \ 647 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 648 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 649 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 650 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 651 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 652 "if test $? -ne 0; then " \ 653 "echo PROGRAM FAILED; " \ 654 "else; " \ 655 "echo PROGRAM SUCCEEDED; " \ 656 "fi; " \ 657 "else; " \ 658 "echo DOWNLOAD FAILED; " \ 659 "fi;" 660 661 #define CONFIG_BOOT_OS_NET \ 662 "$download_cmd $osaddr $osfile; " \ 663 "if test $? -eq 0; then " \ 664 "if test -n $fdtaddr; then " \ 665 "$download_cmd $fdtaddr $fdtfile; " \ 666 "if test $? -eq 0; then " \ 667 "bootm $osaddr - $fdtaddr; " \ 668 "else; " \ 669 "echo FDT DOWNLOAD FAILED; " \ 670 "fi; " \ 671 "else; " \ 672 "bootm $osaddr; " \ 673 "fi; " \ 674 "else; " \ 675 "echo OS DOWNLOAD FAILED; " \ 676 "fi;" 677 678 #define CONFIG_PROG_OS1 \ 679 "$download_cmd $osaddr $osfile; " \ 680 "if test $? -eq 0; then " \ 681 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 682 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 683 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 684 "if test $? -ne 0; then " \ 685 "echo OS PROGRAM FAILED; " \ 686 "else; " \ 687 "echo OS PROGRAM SUCCEEDED; " \ 688 "fi; " \ 689 "else; " \ 690 "echo OS DOWNLOAD FAILED; " \ 691 "fi;" 692 693 #define CONFIG_PROG_OS2 \ 694 "$download_cmd $osaddr $osfile; " \ 695 "if test $? -eq 0; then " \ 696 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 697 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 698 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 699 "if test $? -ne 0; then " \ 700 "echo OS PROGRAM FAILED; " \ 701 "else; " \ 702 "echo OS PROGRAM SUCCEEDED; " \ 703 "fi; " \ 704 "else; " \ 705 "echo OS DOWNLOAD FAILED; " \ 706 "fi;" 707 708 #define CONFIG_PROG_FDT1 \ 709 "$download_cmd $fdtaddr $fdtfile; " \ 710 "if test $? -eq 0; then " \ 711 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 712 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 713 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 714 "if test $? -ne 0; then " \ 715 "echo FDT PROGRAM FAILED; " \ 716 "else; " \ 717 "echo FDT PROGRAM SUCCEEDED; " \ 718 "fi; " \ 719 "else; " \ 720 "echo FDT DOWNLOAD FAILED; " \ 721 "fi;" 722 723 #define CONFIG_PROG_FDT2 \ 724 "$download_cmd $fdtaddr $fdtfile; " \ 725 "if test $? -eq 0; then " \ 726 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 727 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 728 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 729 "if test $? -ne 0; then " \ 730 "echo FDT PROGRAM FAILED; " \ 731 "else; " \ 732 "echo FDT PROGRAM SUCCEEDED; " \ 733 "fi; " \ 734 "else; " \ 735 "echo FDT DOWNLOAD FAILED; " \ 736 "fi;" 737 738 #define CONFIG_EXTRA_ENV_SETTINGS \ 739 "autoload=yes\0" \ 740 "download_cmd=tftp\0" \ 741 "console_args=console=ttyS0,115200\0" \ 742 "root_args=root=/dev/nfs rw\0" \ 743 "misc_args=ip=on\0" \ 744 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 745 "bootfile=/home/user/file\0" \ 746 "osfile=/home/user/board.uImage\0" \ 747 "fdtfile=/home/user/board.dtb\0" \ 748 "ubootfile=/home/user/u-boot.bin\0" \ 749 "fdtaddr=c00000\0" \ 750 "osaddr=0x1000000\0" \ 751 "loadaddr=0x1000000\0" \ 752 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 753 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 754 "prog_os1="CONFIG_PROG_OS1"\0" \ 755 "prog_os2="CONFIG_PROG_OS2"\0" \ 756 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 757 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 758 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 759 "bootcmd_flash1=run set_bootargs; " \ 760 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 761 "bootcmd_flash2=run set_bootargs; " \ 762 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 763 "bootcmd=run bootcmd_flash1\0" 764 #endif /* __CONFIG_H */ 765