1 /* 2 * Configuration for Xilinx ZynqMP 3 * (C) Copyright 2014 - 2015 Xilinx, Inc. 4 * Michal Simek <michal.simek@xilinx.com> 5 * 6 * Based on Configuration for Versatile Express 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #ifndef __XILINX_ZYNQMP_H 12 #define __XILINX_ZYNQMP_H 13 14 #define CONFIG_REMAKE_ELF 15 16 /* #define CONFIG_ARMV8_SWITCH_TO_EL1 */ 17 18 /* Generic Interrupt Controller Definitions */ 19 #define CONFIG_GICV2 20 #define GICD_BASE 0xF9010000 21 #define GICC_BASE 0xF9020000 22 23 #define CONFIG_SYS_ALT_MEMTEST 24 #define CONFIG_SYS_MEMTEST_SCRATCH 0xfffc0000 25 26 #ifndef CONFIG_NR_DRAM_BANKS 27 # define CONFIG_NR_DRAM_BANKS 2 28 #endif 29 #define CONFIG_SYS_MEMTEST_START 0 30 #define CONFIG_SYS_MEMTEST_END 1000 31 32 #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE 33 34 /* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */ 35 #if !defined(COUNTER_FREQUENCY) 36 # define COUNTER_FREQUENCY 100000000 37 #endif 38 39 /* Size of malloc() pool */ 40 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x2000000) 41 42 /* Serial setup */ 43 #define CONFIG_ARM_DCC 44 #define CONFIG_CPU_ARMV8 45 #define CONFIG_ZYNQ_SERIAL 46 47 #define CONFIG_CONS_INDEX 0 48 #define CONFIG_SYS_BAUDRATE_TABLE \ 49 { 4800, 9600, 19200, 38400, 57600, 115200 } 50 51 /* Command line configuration */ 52 #define CONFIG_MP 53 54 /* BOOTP options */ 55 #define CONFIG_BOOTP_BOOTFILESIZE 56 #define CONFIG_BOOTP_BOOTPATH 57 #define CONFIG_BOOTP_GATEWAY 58 #define CONFIG_BOOTP_HOSTNAME 59 #define CONFIG_BOOTP_MAY_FAIL 60 #define CONFIG_BOOTP_DNS 61 #define CONFIG_BOOTP_PXE 62 #define CONFIG_BOOTP_SUBNETMASK 63 64 /* Diff from config_distro_defaults.h */ 65 #define CONFIG_SUPPORT_RAW_INITRD 66 #if !defined(CONFIG_SPL_BUILD) 67 #define CONFIG_ENV_VARS_UBOOT_CONFIG 68 #endif 69 #define CONFIG_AUTO_COMPLETE 70 71 #if defined(CONFIG_MMC_SDHCI_ZYNQ) 72 # define CONFIG_SUPPORT_EMMC_BOOT 73 # ifndef CONFIG_ZYNQ_SDHCI_MAX_FREQ 74 # define CONFIG_ZYNQ_SDHCI_MAX_FREQ 200000000 75 # endif 76 # define FAT_ENV_DEVICE_AND_PART "0:auto" 77 # define FAT_ENV_FILE "uboot.env" 78 # define FAT_ENV_INTERFACE "mmc" 79 #endif 80 81 #ifdef CONFIG_NAND_ARASAN 82 # define CONFIG_CMD_NAND_LOCK_UNLOCK 83 # define CONFIG_SYS_MAX_NAND_DEVICE 1 84 # define CONFIG_SYS_NAND_SELF_INIT 85 # define CONFIG_SYS_NAND_ONFI_DETECTION 86 # define CONFIG_MTD_DEVICE 87 #endif 88 89 /* Miscellaneous configurable options */ 90 #define CONFIG_SYS_LOAD_ADDR 0x8000000 91 92 #if defined(CONFIG_ZYNQMP_USB) 93 #define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x1800000 94 #define DFU_DEFAULT_POLL_TIMEOUT 300 95 #define CONFIG_USB_CABLE_CHECK 96 #define CONFIG_CMD_THOR_DOWNLOAD 97 #define CONFIG_USB_FUNCTION_THOR 98 #define CONFIG_THOR_RESET_OFF 99 #define DFU_ALT_INFO_RAM \ 100 "dfu_ram_info=" \ 101 "setenv dfu_alt_info " \ 102 "Image ram $kernel_addr $kernel_size\\\\;" \ 103 "system.dtb ram $fdt_addr $fdt_size\0" \ 104 "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \ 105 "thor_ram=run dfu_ram_info && thordown 0 ram 0\0" 106 107 #define DFU_ALT_INFO \ 108 DFU_ALT_INFO_RAM 109 110 #ifndef CONFIG_SPL_BUILD 111 # define CONFIG_USB_FUNCTION_FASTBOOT 112 # define CONFIG_CMD_FASTBOOT 113 # define CONFIG_ANDROID_BOOT_IMAGE 114 # define CONFIG_FASTBOOT_BUF_ADDR 0x100000 115 # define CONFIG_FASTBOOT_BUF_SIZE 0x6000000 116 # define CONFIG_FASTBOOT_FLASH 117 # ifdef CONFIG_MMC_SDHCI_ZYNQ 118 # define CONFIG_FASTBOOT_FLASH_MMC_DEV 0 119 # endif 120 121 # define CONFIG_RANDOM_UUID 122 # define PARTS_DEFAULT \ 123 "partitions=uuid_disk=${uuid_gpt_disk};" \ 124 "name=""boot"",size=16M,uuid=${uuid_gpt_boot};" \ 125 "name=""Linux"",size=-M,uuid=${uuid_gpt_Linux}\0" 126 #endif 127 #endif 128 129 #if !defined(DFU_ALT_INFO) 130 # define DFU_ALT_INFO 131 #endif 132 133 #if !defined(PARTS_DEFAULT) 134 # define PARTS_DEFAULT 135 #endif 136 137 /* Do not preserve environment */ 138 #define CONFIG_ENV_SIZE 0x8000 139 140 /* Monitor Command Prompt */ 141 /* Console I/O Buffer Size */ 142 #define CONFIG_SYS_CBSIZE 2048 143 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 144 sizeof(CONFIG_SYS_PROMPT) + 16) 145 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 146 #define CONFIG_SYS_LONGHELP 147 #define CONFIG_CMDLINE_EDITING 148 #define CONFIG_SYS_MAXARGS 64 149 150 /* Ethernet driver */ 151 #if defined(CONFIG_ZYNQ_GEM) 152 # define CONFIG_NET_MULTI 153 # define CONFIG_MII 154 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 155 # define CONFIG_PHY_MARVELL 156 # define CONFIG_PHY_NATSEMI 157 # define CONFIG_PHY_TI 158 # define CONFIG_PHY_GIGE 159 # define CONFIG_PHY_VITESSE 160 # define CONFIG_PHY_REALTEK 161 # define PHY_ANEG_TIMEOUT 20000 162 #endif 163 164 /* I2C */ 165 #if defined(CONFIG_SYS_I2C_ZYNQ) 166 # define CONFIG_SYS_I2C 167 # define CONFIG_SYS_I2C_ZYNQ_SPEED 100000 168 # define CONFIG_SYS_I2C_ZYNQ_SLAVE 0 169 #endif 170 171 /* EEPROM */ 172 #ifdef CONFIG_ZYNQMP_EEPROM 173 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 174 # define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 175 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 176 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 177 # define CONFIG_SYS_EEPROM_SIZE (64 * 1024) 178 #endif 179 180 #ifdef CONFIG_SATA_CEVA 181 #define CONFIG_LIBATA 182 #define CONFIG_SCSI_AHCI 183 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 184 #define CONFIG_SYS_SCSI_MAX_LUN 1 185 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 186 CONFIG_SYS_SCSI_MAX_LUN) 187 #endif 188 189 #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024) 190 191 #define CONFIG_BOARD_EARLY_INIT_R 192 #define CONFIG_CLOCKS 193 194 #define ENV_MEM_LAYOUT_SETTINGS \ 195 "fdt_high=10000000\0" \ 196 "initrd_high=10000000\0" \ 197 "fdt_addr_r=0x40000000\0" \ 198 "pxefile_addr_r=0x10000000\0" \ 199 "kernel_addr_r=0x18000000\0" \ 200 "scriptaddr=0x02000000\0" \ 201 "ramdisk_addr_r=0x02100000\0" \ 202 203 #if defined(CONFIG_MMC_SDHCI_ZYNQ) 204 # define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) func(MMC, mmc, 1) 205 #else 206 # define BOOT_TARGET_DEVICES_MMC(func) 207 #endif 208 209 #if defined(CONFIG_SATA_CEVA) 210 # define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0) 211 #else 212 # define BOOT_TARGET_DEVICES_SCSI(func) 213 #endif 214 215 #if defined(CONFIG_ZYNQMP_USB) 216 # define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) func(USB, usb, 1) 217 #else 218 # define BOOT_TARGET_DEVICES_USB(func) 219 #endif 220 221 #define BOOT_TARGET_DEVICES(func) \ 222 BOOT_TARGET_DEVICES_MMC(func) \ 223 BOOT_TARGET_DEVICES_USB(func) \ 224 BOOT_TARGET_DEVICES_SCSI(func) \ 225 func(PXE, pxe, na) \ 226 func(DHCP, dhcp, na) 227 228 #include <config_distro_bootcmd.h> 229 230 /* Initial environment variables */ 231 #ifndef CONFIG_EXTRA_ENV_SETTINGS 232 #define CONFIG_EXTRA_ENV_SETTINGS \ 233 ENV_MEM_LAYOUT_SETTINGS \ 234 BOOTENV \ 235 DFU_ALT_INFO 236 #endif 237 238 /* SPL can't handle all huge variables - define just DFU */ 239 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU_SUPPORT) 240 #undef CONFIG_EXTRA_ENV_SETTINGS 241 # define CONFIG_EXTRA_ENV_SETTINGS \ 242 "dfu_alt_info_ram=uboot.bin ram 0x8000000 0x1000000;" \ 243 "atf-uboot.ub ram 0x10000000 0x1000000;" \ 244 "Image ram 0x80000 0x3f80000;" \ 245 "system.dtb ram 0x4000000 0x100000\0" \ 246 "dfu_bufsiz=0x1000\0" 247 #endif 248 249 #define CONFIG_SPL_TEXT_BASE 0xfffc0000 250 #define CONFIG_SPL_STACK 0xfffffffc 251 #define CONFIG_SPL_MAX_SIZE 0x40000 252 253 /* Just random location in OCM */ 254 #define CONFIG_SPL_BSS_START_ADDR 0x0 255 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 256 257 #define CONFIG_SPL_FRAMEWORK 258 259 /* u-boot is like dtb */ 260 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "u-boot.bin" 261 #define CONFIG_SYS_SPL_ARGS_ADDR 0x8000000 262 263 /* ATF is my kernel image */ 264 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "atf-uboot.ub" 265 266 /* FIT load address for RAM boot */ 267 #define CONFIG_SPL_LOAD_FIT_ADDRESS 0x10000000 268 269 /* MMC support */ 270 #ifdef CONFIG_MMC_SDHCI_ZYNQ 271 # define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 272 # define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 /* unused */ 273 # define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 /* unused */ 274 # define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 /* unused */ 275 # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 276 #endif 277 278 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU_SUPPORT) 279 # undef CONFIG_CMD_BOOTD 280 # define CONFIG_SPL_ENV_SUPPORT 281 # define CONFIG_SPL_HASH_SUPPORT 282 # define CONFIG_ENV_MAX_ENTRIES 10 283 284 # define CONFIG_SYS_SPL_MALLOC_START 0x20000000 285 # define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 286 287 #ifdef CONFIG_SPL_SYS_MALLOC_SIMPLE 288 # error "Disable CONFIG_SPL_SYS_MALLOC_SIMPLE. Full malloc needs to be used" 289 #endif 290 #endif 291 292 #define CONFIG_BOARD_EARLY_INIT_F 293 294 #endif /* __XILINX_ZYNQMP_H */ 295