1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2009, STMicroelectronics - All Rights Reserved 4 * Author(s): Vipin Kumar, <vipin.kumar@st.com> for STMicroelectronics. 5 * 6 * Copyright (C) 2012, 2015 Stefan Roese <sr@denx.de> 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 * (easy to change) 15 */ 16 #define CONFIG_SPEAR600 /* SPEAr600 SoC */ 17 #define CONFIG_X600 /* on X600 board */ 18 19 #include <asm/arch/hardware.h> 20 21 /* Timer, HZ specific defines */ 22 #define CONFIG_SYS_HZ_CLOCK 8300000 23 24 #define CONFIG_SYS_FLASH_BASE 0xf8000000 25 /* Reserve 8KiB for SPL */ 26 #define CONFIG_SPL_PAD_TO 8192 /* decimal for 'dd' */ 27 #define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO 28 #define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \ 29 CONFIG_SYS_SPL_LEN) 30 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 31 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 32 #define CONFIG_SYS_MONITOR_LEN 0x60000 33 34 /* Serial Configuration (PL011) */ 35 #define CONFIG_SYS_SERIAL0 0xD0000000 36 #define CONFIG_SYS_SERIAL1 0xD0080000 37 #define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \ 38 (void *)CONFIG_SYS_SERIAL1 } 39 #define CONFIG_PL011_CLOCK (48 * 1000 * 1000) 40 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \ 41 57600, 115200 } 42 #define CONFIG_SYS_LOADS_BAUD_CHANGE 43 44 /* NOR FLASH config options */ 45 #define CONFIG_ST_SMI 46 #define CONFIG_SYS_MAX_FLASH_BANKS 1 47 #define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000 48 #define CONFIG_SYS_FLASH_ADDR_BASE { CONFIG_SYS_FLASH_BASE } 49 #define CONFIG_SYS_MAX_FLASH_SECT 128 50 #define CONFIG_SYS_FLASH_EMPTY_INFO 51 #define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ) 52 #define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ) 53 54 /* NAND FLASH config options */ 55 #define CONFIG_NAND_FSMC 56 #define CONFIG_SYS_NAND_SELF_INIT 57 #define CONFIG_SYS_MAX_NAND_DEVICE 1 58 #define CONFIG_SYS_NAND_BASE CONFIG_FSMC_NAND_BASE 59 #define CONFIG_MTD_ECC_SOFT 60 #define CONFIG_SYS_FSMC_NAND_8BIT 61 #define CONFIG_SYS_NAND_ONFI_DETECTION 62 #define CONFIG_NAND_ECC_BCH 63 64 /* UBI/UBI config options */ 65 66 /* Ethernet config options */ 67 #define CONFIG_PHY_RESET_DELAY 10000 /* in usec */ 68 69 #define CONFIG_SPEAR_GPIO 70 71 /* I2C config options */ 72 #define CONFIG_SYS_I2C 73 #define CONFIG_SYS_I2C_BASE 0xD0200000 74 #define CONFIG_SYS_I2C_SPEED 400000 75 #define CONFIG_SYS_I2C_SLAVE 0x02 76 #define CONFIG_I2C_CHIPADDRESS 0x50 77 78 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 79 80 /* FPGA config options */ 81 #define CONFIG_FPGA_COUNT 1 82 83 /* USB EHCI options */ 84 #define CONFIG_USB_EHCI_SPEAR 85 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 86 87 /* 88 * U-Boot Environment placing definitions. 89 */ 90 #define CONFIG_ENV_SECT_SIZE 0x00010000 91 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 92 CONFIG_SYS_MONITOR_LEN) 93 #define CONFIG_ENV_SIZE 0x02000 94 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + \ 95 CONFIG_ENV_SECT_SIZE) 96 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 97 98 /* Miscellaneous configurable options */ 99 #define CONFIG_ARCH_CPU_INIT 100 #define CONFIG_BOOT_PARAMS_ADDR 0x00000100 101 #define CONFIG_CMDLINE_TAG 102 #define CONFIG_SETUP_MEMORY_TAGS 103 #define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ 104 105 #define CONFIG_SYS_MEMTEST_START 0x00800000 106 #define CONFIG_SYS_MEMTEST_END 0x04000000 107 #define CONFIG_SYS_MALLOC_LEN (8 << 20) 108 #define CONFIG_SYS_LOAD_ADDR 0x00800000 109 110 #define CONFIG_HOSTNAME "x600" 111 #define CONFIG_UBI_PART ubi0 112 #define CONFIG_UBIFS_VOLUME rootfs 113 114 #define CONFIG_EXTRA_ENV_SETTINGS \ 115 "u-boot_addr=1000000\0" \ 116 "u-boot=" CONFIG_HOSTNAME "/u-boot.spr\0" \ 117 "load=tftp ${u-boot_addr} ${u-boot}\0" \ 118 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 119 " +${filesize};" \ 120 "erase " __stringify(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \ 121 "cp.b ${u-boot_addr} " __stringify(CONFIG_SYS_MONITOR_BASE) \ 122 " ${filesize};" \ 123 "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ 124 " +${filesize}\0" \ 125 "upd=run load update\0" \ 126 "ubifs=" CONFIG_HOSTNAME "/ubifs.img\0" \ 127 "part=" __stringify(CONFIG_UBI_PART) "\0" \ 128 "vol=" __stringify(CONFIG_UBIFS_VOLUME) "\0" \ 129 "load_ubifs=tftp ${kernel_addr} ${ubifs}\0" \ 130 "update_ubifs=ubi part ${part};ubi write ${kernel_addr} ${vol}" \ 131 " ${filesize}\0" \ 132 "upd_ubifs=run load_ubifs update_ubifs\0" \ 133 "init_ubifs=nand erase.part ubi0;ubi part ${part};" \ 134 "ubi create ${vol} 4000000\0" \ 135 "netdev=eth0\0" \ 136 "rootpath=/opt/eldk-4.2/arm\0" \ 137 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 138 "nfsroot=${serverip}:${rootpath}\0" \ 139 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 140 "boot_part=0\0" \ 141 "altbootcmd=if test $boot_part -eq 0;then " \ 142 "echo Switching to partition 1!;" \ 143 "setenv boot_part 1;" \ 144 "else; " \ 145 "echo Switching to partition 0!;" \ 146 "setenv boot_part 0;" \ 147 "fi;" \ 148 "saveenv;boot\0" \ 149 "ubifsargs=set bootargs ubi.mtd=ubi${boot_part} " \ 150 "root=ubi0:rootfs rootfstype=ubifs\0" \ 151 "kernel=" CONFIG_HOSTNAME "/uImage\0" \ 152 "kernel_fs=/boot/uImage \0" \ 153 "kernel_addr=1000000\0" \ 154 "dtb=" CONFIG_HOSTNAME "/" \ 155 CONFIG_HOSTNAME ".dtb\0" \ 156 "dtb_fs=/boot/" CONFIG_HOSTNAME ".dtb\0" \ 157 "dtb_addr=1800000\0" \ 158 "load_kernel=tftp ${kernel_addr} ${kernel}\0" \ 159 "load_dtb=tftp ${dtb_addr} ${dtb}\0" \ 160 "addip=setenv bootargs ${bootargs} " \ 161 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 162 ":${hostname}:${netdev}:off panic=1\0" \ 163 "addcon=setenv bootargs ${bootargs} console=ttyAMA0," \ 164 "${baudrate}\0" \ 165 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 166 "net_nfs=run load_dtb load_kernel; " \ 167 "run nfsargs addip addcon addmtd addmisc;" \ 168 "bootm ${kernel_addr} - ${dtb_addr}\0" \ 169 "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ 170 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ 171 "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip" \ 172 " addcon addmisc addmtd;" \ 173 "bootm ${kernel_addr} - ${dtb_addr}\0" \ 174 "ubifs_mount=ubi part ubi${boot_part};ubifsmount ubi:rootfs\0" \ 175 "ubifs_load=ubifsload ${kernel_addr} ${kernel_fs};" \ 176 "ubifsload ${dtb_addr} ${dtb_fs};\0" \ 177 "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip addcon " \ 178 "addmtd addmisc;bootm ${kernel_addr} - ${dtb_addr}\0" \ 179 "bootcmd=run nand_ubifs\0" \ 180 "\0" 181 182 /* Physical Memory Map */ 183 #define PHYS_SDRAM_1 0x00000000 184 #define PHYS_SDRAM_1_MAXSIZE 0x40000000 185 186 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 187 #define CONFIG_SRAM_BASE 0xd2800000 188 /* Preserve the last 2 lwords for the boot-counter */ 189 #define CONFIG_SRAM_SIZE ((8 << 10) - 0x8) 190 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE 191 #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE 192 193 #define CONFIG_SYS_INIT_SP_OFFSET \ 194 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 195 196 #define CONFIG_SYS_INIT_SP_ADDR \ 197 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 198 199 /* 200 * SPL related defines 201 */ 202 #define CONFIG_SPL_TEXT_BASE 0xd2800b00 203 #define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00) 204 #define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear" 205 206 /* 207 * Please select/define only one of the following 208 * Each definition corresponds to a supported DDR chip. 209 * DDR configuration is based on the following selection 210 */ 211 #define CONFIG_DDR_MT47H64M16 1 212 #define CONFIG_DDR_MT47H32M16 0 213 #define CONFIG_DDR_MT47H128M8 0 214 215 /* 216 * Synchronous/Asynchronous operation of DDR 217 * 218 * Select CONFIG_DDR_2HCLK for DDR clk = 333MHz, synchronous operation 219 * Select CONFIG_DDR_HCLK for DDR clk = 166MHz, synchronous operation 220 * Select CONFIG_DDR_PLL2 for DDR clk = PLL2, asynchronous operation 221 */ 222 #define CONFIG_DDR_2HCLK 1 223 #define CONFIG_DDR_HCLK 0 224 #define CONFIG_DDR_PLL2 0 225 226 /* 227 * xxx_BOOT_SUPPORTED macro defines whether a booting type is supported 228 * or not. Modify/Add to only these macros to define new boot types 229 */ 230 #define USB_BOOT_SUPPORTED 0 231 #define PCIE_BOOT_SUPPORTED 0 232 #define SNOR_BOOT_SUPPORTED 1 233 #define NAND_BOOT_SUPPORTED 1 234 #define PNOR_BOOT_SUPPORTED 0 235 #define TFTP_BOOT_SUPPORTED 0 236 #define UART_BOOT_SUPPORTED 0 237 #define SPI_BOOT_SUPPORTED 0 238 #define I2C_BOOT_SUPPORTED 0 239 #define MMC_BOOT_SUPPORTED 0 240 241 #endif /* __CONFIG_H */ 242