1 /* 2 * (C) Copyright 2011, Stefano Babic <sbabic@denx.de> 3 * 4 * (C) Copyright 2008-2010 Freescale Semiconductor, Inc. 5 * 6 * Configuration for the woodburn board. 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #ifndef __WOODBURN_COMMON_CONFIG_H 12 #define __WOODBURN_COMMON_CONFIG_H 13 14 #include <asm/arch/imx-regs.h> 15 16 /* High Level Configuration Options */ 17 #define CONFIG_MX35 18 #define CONFIG_MX35_HCLK_FREQ 24000000 19 #define CONFIG_SYS_FSL_CLK 20 21 #define CONFIG_SYS_DCACHE_OFF 22 #define CONFIG_SYS_CACHELINE_SIZE 32 23 24 #define CONFIG_DISPLAY_CPUINFO 25 26 /* Only in case the value is not present in mach-types.h */ 27 #ifndef MACH_TYPE_FLEA3 28 #define MACH_TYPE_FLEA3 3668 29 #endif 30 31 #define CONFIG_MACH_TYPE MACH_TYPE_FLEA3 32 33 /* This is required to setup the ESDC controller */ 34 35 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 36 #define CONFIG_REVISION_TAG 37 #define CONFIG_SETUP_MEMORY_TAGS 38 #define CONFIG_INITRD_TAG 39 40 /* 41 * Size of malloc() pool 42 */ 43 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) 44 45 /* 46 * Hardware drivers 47 */ 48 #define CONFIG_SYS_I2C 49 #define CONFIG_SYS_I2C_MXC 50 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 51 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 52 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 53 #define CONFIG_SYS_SPD_BUS_NUM 0 54 #define CONFIG_MXC_SPI 55 #define CONFIG_MXC_GPIO 56 57 /* PMIC Controller */ 58 #define CONFIG_POWER 59 #define CONFIG_POWER_I2C 60 #define CONFIG_POWER_FSL 61 #define CONFIG_POWER_FSL_MC13892 62 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8 63 #define CONFIG_RTC_MC13XXX 64 65 /* mmc driver */ 66 #define CONFIG_MMC 67 #define CONFIG_GENERIC_MMC 68 #define CONFIG_FSL_ESDHC 69 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 70 #define CONFIG_SYS_FSL_ESDHC_NUM 1 71 72 /* 73 * UART (console) 74 */ 75 #define CONFIG_MXC_UART 76 #define CONFIG_MXC_UART_BASE UART1_BASE 77 78 /* allow to overwrite serial and ethaddr */ 79 #define CONFIG_ENV_OVERWRITE 80 #define CONFIG_CONS_INDEX 1 81 #define CONFIG_BAUDRATE 115200 82 83 /* 84 * Command definition 85 */ 86 #define CONFIG_CMD_DATE 87 #define CONFIG_BOOTP_SUBNETMASK 88 #define CONFIG_BOOTP_GATEWAY 89 #define CONFIG_BOOTP_DNS 90 91 #define CONFIG_CMD_NAND 92 93 #define CONFIG_DOS_PARTITION 94 #define CONFIG_EFI_PARTITION 95 96 #define CONFIG_MXC_GPIO 97 98 #define CONFIG_NET_RETRY_COUNT 100 99 100 #define CONFIG_BOOTDELAY 3 101 102 #define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */ 103 104 /* 105 * Ethernet on SOC (FEC) 106 */ 107 #define CONFIG_FEC_MXC 108 #define IMX_FEC_BASE FEC_BASE_ADDR 109 #define CONFIG_PHYLIB 110 #define CONFIG_PHY_MICREL 111 #define CONFIG_FEC_MXC_PHYADDR 0x1 112 113 #define CONFIG_MII 114 #define CONFIG_DISCOVER_PHY 115 116 #define CONFIG_ARP_TIMEOUT 200UL 117 118 /* 119 * Miscellaneous configurable options 120 */ 121 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 122 #define CONFIG_CMDLINE_EDITING 123 124 #define CONFIG_AUTO_COMPLETE 125 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 126 /* Print Buffer Size */ 127 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 128 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 129 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 130 131 #define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */ 132 #define CONFIG_SYS_MEMTEST_END 0x10000 133 134 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 135 136 /* 137 * Stack sizes 138 * 139 * The stack sizes are set up in start.S using the settings below 140 */ 141 #define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ 142 143 /* 144 * Physical Memory Map 145 */ 146 #define CONFIG_NR_DRAM_BANKS 1 147 #define PHYS_SDRAM_1 CSD0_BASE_ADDR 148 #define PHYS_SDRAM_1_SIZE (256 * 1024 * 1024) 149 150 #define CONFIG_SYS_SDRAM_BASE CSD0_BASE_ADDR 151 152 #define CONFIG_SYS_GBL_DATA_OFFSET (LOW_LEVEL_SRAM_STACK - \ 153 IRAM_BASE_ADDR - \ 154 GENERATED_GBL_DATA_SIZE) 155 #define CONFIG_SYS_INIT_SP_ADDR (IRAM_BASE_ADDR + \ 156 CONFIG_SYS_GBL_DATA_OFFSET) 157 158 /* 159 * MTD Command for mtdparts 160 */ 161 #define CONFIG_CMD_MTDPARTS 162 #define CONFIG_MTD_DEVICE 163 #define CONFIG_FLASH_CFI_MTD 164 #define CONFIG_MTD_PARTITIONS 165 #define MTDIDS_DEFAULT "nand0=mxc_nand,nor0=physmap-flash.0" 166 #define MTDPARTS_DEFAULT "mtdparts=mxc_nand:50m(root1)," \ 167 "32m(rootfb)," \ 168 "64m(pcache)," \ 169 "64m(app1)," \ 170 "10m(app2),-(spool);" \ 171 "physmap-flash.0:512k(u-boot),64k(env1)," \ 172 "64k(env2),3776k(kernel1),3776k(kernel2)" 173 174 /* 175 * FLASH and environment organization 176 */ 177 #define CONFIG_SYS_FLASH_BASE CS0_BASE_ADDR 178 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 179 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ 180 /* Monitor at beginning of flash */ 181 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 182 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) 183 184 #define CONFIG_ENV_SECT_SIZE (128 * 1024) 185 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 186 187 /* Address and size of Redundant Environment Sector */ 188 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) 189 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 190 191 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 192 CONFIG_SYS_MONITOR_LEN) 193 194 #define CONFIG_ENV_IS_IN_FLASH 195 196 /* 197 * CFI FLASH driver setup 198 */ 199 #define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */ 200 #define CONFIG_FLASH_CFI_DRIVER 201 202 /* A non-standard buffered write algorithm */ 203 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* faster */ 204 #define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */ 205 206 /* 207 * NAND FLASH driver setup 208 */ 209 #define CONFIG_NAND_MXC 210 #define CONFIG_NAND_MXC_V1_1 211 #define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR) 212 #define CONFIG_SYS_MAX_NAND_DEVICE 1 213 #define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR) 214 #define CONFIG_MXC_NAND_HWECC 215 #define CONFIG_SYS_NAND_LARGEPAGE 216 217 #if 0 218 #define CONFIG_MTD_DEBUG 219 #define CONFIG_MTD_DEBUG_VERBOSE 7 220 #endif 221 #define CONFIG_SYS_NAND_ONFI_DETECTION 222 223 /* 224 * Default environment and default scripts 225 * to update uboot and load kernel 226 */ 227 228 #define CONFIG_HOSTNAME woodburn 229 #define CONFIG_EXTRA_ENV_SETTINGS \ 230 "netdev=eth0\0" \ 231 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 232 "nfsroot=${serverip}:${rootpath}\0" \ 233 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 234 "addip_sta=setenv bootargs ${bootargs} " \ 235 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 236 ":${hostname}:${netdev}:off panic=1\0" \ 237 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ 238 "addip=if test -n ${ipdyn};then run addip_dyn;" \ 239 "else run addip_sta;fi\0" \ 240 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 241 "addtty=setenv bootargs ${bootargs}" \ 242 " console=ttymxc0,${baudrate}\0" \ 243 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ 244 "loadaddr=80800000\0" \ 245 "kernel_addr_r=80800000\0" \ 246 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \ 247 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \ 248 "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0" \ 249 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 250 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 251 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 252 "bootm ${kernel_addr}\0" \ 253 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 254 "run nfsargs addip addtty addmtd addmisc;" \ 255 "bootm ${kernel_addr_r}\0" \ 256 "net_self_load=tftp ${kernel_addr_r} ${bootfile};" \ 257 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \ 258 "net_self=if run net_self_load;then " \ 259 "run ramargs addip addtty addmtd addmisc;" \ 260 "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \ 261 "else echo Images not loades;fi\0" \ 262 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \ 263 "load=tftp ${loadaddr} ${u-boot}\0" \ 264 "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \ 265 "update=protect off ${uboot_addr} +80000;" \ 266 "erase ${uboot_addr} +80000;" \ 267 "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \ 268 "upd=if run load;then echo Updating u-boot;if run update;" \ 269 "then echo U-Boot updated;" \ 270 "else echo Error updating u-boot !;" \ 271 "echo Board without bootloader !!;" \ 272 "fi;" \ 273 "else echo U-Boot not downloaded..exiting;fi\0" \ 274 "bootcmd=run net_nfs\0" 275 276 #endif /* __CONFIG_H */ 277