1 /* 2 * Configuration settings for the VInCo platform. 3 * 4 * Based on the settings for the SAMA5-EK board 5 * Copyright (C) 2014 Atmel 6 * Bo Shen <voice.shen@atmel.com> 7 * Copyright (C) 2015 Free Electrons 8 * Gregory CLEMENT gregory.clement@free-electrons.com 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 /* No NOR flash, this definition should be put before common header */ 17 #define CONFIG_SYS_NO_FLASH 18 19 #include "at91-sama5_common.h" 20 21 /* The value in the common file is too far away for the VInCo platform */ 22 #ifdef CONFIG_SYS_TEXT_BASE 23 #undef CONFIG_SYS_TEXT_BASE 24 #endif 25 #define CONFIG_SYS_TEXT_BASE 0x20f00000 26 27 /* serial console */ 28 #define CONFIG_ATMEL_USART 29 #define CONFIG_USART_BASE ATMEL_BASE_USART3 30 #define CONFIG_USART_ID ATMEL_ID_USART3 31 32 /* SDRAM */ 33 #define CONFIG_NR_DRAM_BANKS 1 34 #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS 35 #define CONFIG_SYS_SDRAM_SIZE 0x4000000 36 37 #define CONFIG_SYS_INIT_SP_ADDR \ 38 (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) 39 40 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 41 42 /* SerialFlash */ 43 44 #ifdef CONFIG_CMD_SF 45 #define CONFIG_ATMEL_SPI 46 #define CONFIG_ATMEL_SPI0 47 #define CONFIG_SPI_FLASH_STMICRO 48 #define CONFIG_SF_DEFAULT_BUS 0 49 #define CONFIG_SF_DEFAULT_CS 0 50 #define CONFIG_SF_DEFAULT_SPEED 50000000 51 #define CONFIG_ENV_SPI_MAX_HZ 50000000 52 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) 53 #define CONFIG_ENV_SPI_MODE (SPI_MODE_0) 54 #endif 55 56 /* MMC */ 57 58 #ifdef CONFIG_CMD_MMC 59 #define CONFIG_SUPPORT_EMMC_BOOT 60 #define CONFIG_MMC 61 #define CONFIG_GENERIC_MMC 62 #define CONFIG_GENERIC_ATMEL_MCI 63 #define ATMEL_BASE_MMCI ATMEL_BASE_MCI1 64 #define CONFIG_SYS_MMC_CLK_OD 500000 65 66 /* For generating MMC partitions */ 67 #define CONFIG_PARTITION_UUIDS 68 #define CONFIG_RANDOM_UUID 69 #define CONFIG_EFI_PARTITION 70 #define CONFIG_CMD_GPT 71 72 #endif 73 74 /* USB */ 75 76 #ifdef CONFIG_CMD_USB 77 #define CONFIG_USB_EHCI 78 #define CONFIG_USB_EHCI_ATMEL 79 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 80 #endif 81 82 /* USB device */ 83 #define CONFIG_USB_ETHER 84 #define CONFIG_USB_ETH_RNDIS 85 #define CONFIG_USBNET_MANUFACTURER "L+G VInCo" 86 87 #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) 88 #define CONFIG_DOS_PARTITION 89 #endif 90 91 /* Ethernet Hardware */ 92 #define CONFIG_PHY_SMSC 93 #define CONFIG_MACB 94 #define CONFIG_RMII 95 #define CONFIG_NET_RETRY_COUNT 20 96 #define CONFIG_MACB_SEARCH_PHY 97 98 #define CONFIG_USB_HOST_ETHER 99 #define CONFIG_USB_ETHER_SMSC95XX 100 #define CONFIG_USB_ETHER_RNDIS 101 102 #ifdef CONFIG_SYS_USE_SERIALFLASH 103 /* bootstrap + u-boot + env + linux in serial flash */ 104 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS 105 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 106 /* Use our own mapping for the VInCo platform */ 107 #undef CONFIG_ENV_OFFSET 108 #undef CONFIG_ENV_SIZE 109 110 #define CONFIG_ENV_OFFSET 0x10000 111 #define CONFIG_ENV_SIZE 0x10000 112 113 /* Update the bootcommand according to our mapping for the VInCo platform */ 114 #undef CONFIG_BOOTCOMMAND 115 #define CONFIG_BOOTCOMMAND "mmc dev 0 0;" \ 116 "mmc read ${loadaddr} ${k_offset} ${k_blksize};" \ 117 "mmc read ${oftaddr} ${dtb_offset} ${dtb_blksize};" \ 118 "bootz ${loadaddr} - ${oftaddr}" 119 120 #undef CONFIG_BOOTARGS 121 #define CONFIG_BOOTARGS "console=ttyS0,115200 earlyprintk rw root=/dev/mmcblk0p2 rootfstype=ext4 rootwait quiet lpj=1990656" 122 123 #define CONFIG_EXTRA_ENV_SETTINGS \ 124 "kernel_start=0x20000\0" \ 125 "kernel_size=0x800000\0" \ 126 "mmcblksize=0x200\0" \ 127 "oftaddr=0x21000000\0" \ 128 "loadaddr=0x22000000\0" \ 129 "update_uboot=tftp ${loadaddr} u-boot.bin;sf probe 0;" \ 130 "sf erase 0x20000 0x4B000; sf write ${loadaddr} 0x20000 0x4B000\0" \ 131 "create_partition=setexpr dtb_start ${kernel_start} + 0x400000;" \ 132 "setexpr rootfs_start ${kernel_start} + ${kernel_size};" \ 133 "setenv partitions 'name=kernel,size=${kernel_size}," \ 134 "start=${kernel_start};name=rootfs,size=-';" \ 135 "gpt write mmc 0 ${partitions} \0"\ 136 "f2blk_size=setexpr fileblksize ${filesize} / ${mmcblksize};" \ 137 "setexpr fileblksize ${fileblksize} + 1\0" \ 138 "store_kernel=tftp ${loadaddr} zImage; run f2blk_size;" \ 139 "setexpr k_blksize ${fileblksize};" \ 140 "setexpr k_offset ${kernel_start} / ${mmcblksize};" \ 141 "mmc write ${fileaddr} ${k_offset} ${fileblksize}\0" \ 142 "store_dtb=tftp ${loadaddr} at91-vinco.dtb; run f2blk_size;" \ 143 "setexpr dtb_blksize ${fileblksize};" \ 144 "setexpr dtb_offset ${dtb_start} / ${mmcblksize};" \ 145 "mmc write ${fileaddr} ${dtb_offset} ${fileblksize}\0" \ 146 "store_rootfs=tftp ${loadaddr} vinco-gateway-image-vinco.ext4;" \ 147 "setexpr rootfs_offset ${rootfs_start} / ${mmcblksize};" \ 148 "mmc write ${fileaddr} ${rootfs_offset} ${fileblksize}\0" \ 149 "bootdelay=0\0" 150 151 #endif 152 153 #endif 154