1 /* 2 * Copyright (C) Freescale Semiconductor, Inc. 2006. 3 * 4 * (C) Copyright 2010 5 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 /* 10 * ve8313 board configuration file 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 #define CONFIG_SYS_GENERIC_BOARD 17 #define CONFIG_DISPLAY_BOARDINFO 18 19 /* 20 * High Level Configuration Options 21 */ 22 #define CONFIG_E300 1 23 #define CONFIG_MPC831x 1 24 #define CONFIG_MPC8313 1 25 #define CONFIG_VE8313 1 26 27 #ifndef CONFIG_SYS_TEXT_BASE 28 #define CONFIG_SYS_TEXT_BASE 0xfe000000 29 #endif 30 31 #define CONFIG_PCI 1 32 #define CONFIG_PCI_INDIRECT_BRIDGE 1 33 #define CONFIG_FSL_ELBC 1 34 35 #define CONFIG_BOARD_EARLY_INIT_F 1 36 37 /* 38 * On-board devices 39 * 40 */ 41 #define CONFIG_83XX_CLKIN 32000000 /* in Hz */ 42 43 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 44 45 #define CONFIG_SYS_IMMR 0xE0000000 46 47 #define CONFIG_SYS_MEMTEST_START 0x00001000 48 #define CONFIG_SYS_MEMTEST_END 0x07000000 49 50 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth */ 51 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count */ 52 53 /* 54 * Device configurations 55 */ 56 57 /* 58 * DDR Setup 59 */ 60 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ 61 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 62 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 63 64 /* 65 * Manually set up DDR parameters, as this board does not 66 * have the SPD connected to I2C. 67 */ 68 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 69 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 70 | CSCONFIG_AP \ 71 | CSCONFIG_ODT_RD_NEVER \ 72 | CSCONFIG_ODT_WR_ALL \ 73 | CSCONFIG_ROW_BIT_13 \ 74 | CSCONFIG_COL_BIT_10) 75 /* 0x80840102 */ 76 77 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 78 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 79 | (0 << TIMING_CFG0_WRT_SHIFT) \ 80 | (3 << TIMING_CFG0_RRT_SHIFT) \ 81 | (2 << TIMING_CFG0_WWT_SHIFT) \ 82 | (7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 83 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 84 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 85 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 86 /* 0x0e720802 */ 87 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 88 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 89 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 90 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 91 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 92 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 93 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 94 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 95 /* 0x26256222 */ 96 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 97 | (5 << TIMING_CFG2_CPO_SHIFT) \ 98 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 99 | (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 100 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 101 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 102 | (7 << TIMING_CFG2_FOUR_ACT_SHIFT)) 103 /* 0x029028c7 */ 104 #define CONFIG_SYS_DDR_INTERVAL ((0x320 << SDRAM_INTERVAL_REFINT_SHIFT) \ 105 | (0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 106 /* 0x03202000 */ 107 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \ 108 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 109 | SDRAM_CFG_DBW_32) 110 /* 0x43080000 */ 111 #define CONFIG_SYS_SDRAM_CFG2 0x00401000 112 #define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \ 113 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 114 /* 0x44400232 */ 115 #define CONFIG_SYS_DDR_MODE_2 0x8000C000 116 117 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 118 /*0x02000000*/ 119 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 120 | DDRCDR_PZ_NOMZ \ 121 | DDRCDR_NZ_NOMZ \ 122 | DDRCDR_M_ODR) 123 /* 0x73000002 */ 124 125 /* 126 * FLASH on the Local Bus 127 */ 128 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 129 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 130 #define CONFIG_SYS_FLASH_BASE 0xFE000000 131 #define CONFIG_SYS_FLASH_SIZE 32 /* size in MB */ 132 #define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ 133 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ 134 135 #define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \ 136 | BR_PS_16 /* 16 bit */ \ 137 | BR_MS_GPCM /* MSEL = GPCM */ \ 138 | BR_V) /* valid */ 139 #define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 140 | OR_GPCM_CSNT \ 141 | OR_GPCM_ACS_DIV4 \ 142 | OR_GPCM_SCY_5 \ 143 | OR_GPCM_TRLX_SET \ 144 | OR_GPCM_EAD) 145 /* 0xfe000c55 */ 146 147 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 148 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 149 150 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 151 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per dev */ 152 153 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 154 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 155 156 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 157 158 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 159 #define CONFIG_SYS_RAMBOOT 160 #endif 161 162 #define CONFIG_SYS_INIT_RAM_LOCK 1 163 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ 164 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ 165 166 #define CONFIG_SYS_GBL_DATA_OFFSET \ 167 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 168 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 169 170 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 171 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) 172 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) 173 174 /* 175 * Local Bus LCRR and LBCR regs 176 */ 177 #define CONFIG_SYS_LCRR_EADC LCRR_EADC_3 178 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 179 180 #define CONFIG_SYS_LBC_LBCR 0x00040000 181 182 #define CONFIG_SYS_LBC_MRTPR 0x20000000 183 184 /* 185 * NAND settings 186 */ 187 #define CONFIG_SYS_NAND_BASE 0x61000000 188 #define CONFIG_SYS_MAX_NAND_DEVICE 1 189 #define CONFIG_CMD_NAND 1 190 #define CONFIG_NAND_FSL_ELBC 1 191 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384 192 193 #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ 194 | BR_PS_8 \ 195 | BR_DECC_CHK_GEN \ 196 | BR_MS_FCM \ 197 | BR_V) /* valid */ 198 /* 0x61000c21 */ 199 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \ 200 | OR_FCM_BCTLD \ 201 | OR_FCM_CHT \ 202 | OR_FCM_SCY_2 \ 203 | OR_FCM_RST \ 204 | OR_FCM_TRLX) 205 /* 0xffff90ac */ 206 207 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM 208 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM 209 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 210 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM 211 212 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 213 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 214 215 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM 216 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM 217 218 /* CS2 NvRAM */ 219 #define CONFIG_SYS_BR2_PRELIM (0x60000000 \ 220 | BR_PS_8 \ 221 | BR_V) 222 /* 0x60000801 */ 223 #define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB \ 224 | OR_GPCM_CSNT \ 225 | OR_GPCM_XACS \ 226 | OR_GPCM_SCY_3 \ 227 | OR_GPCM_TRLX_SET \ 228 | OR_GPCM_EHTR_SET \ 229 | OR_GPCM_EAD) 230 /* 0xfffe0937 */ 231 /* local bus read write buffer mapping SRAM@0x64000000 */ 232 #define CONFIG_SYS_BR3_PRELIM (0x62000000 \ 233 | BR_PS_16 \ 234 | BR_V) 235 /* 0x62001001 */ 236 237 #define CONFIG_SYS_OR3_PRELIM (OR_AM_32MB \ 238 | OR_GPCM_CSNT \ 239 | OR_GPCM_XACS \ 240 | OR_GPCM_SCY_15 \ 241 | OR_GPCM_TRLX_SET \ 242 | OR_GPCM_EHTR_SET \ 243 | OR_GPCM_EAD) 244 /* 0xfe0009f7 */ 245 246 /* pass open firmware flat tree */ 247 #define CONFIG_OF_LIBFDT 1 248 #define CONFIG_OF_BOARD_SETUP 1 249 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 250 251 /* 252 * Serial Port 253 */ 254 #define CONFIG_CONS_INDEX 1 255 #define CONFIG_SYS_NS16550 256 #define CONFIG_SYS_NS16550_SERIAL 257 #define CONFIG_SYS_NS16550_REG_SIZE 1 258 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 259 260 #define CONFIG_SYS_BAUDRATE_TABLE \ 261 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 262 263 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 264 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 265 266 /* Use the HUSH parser */ 267 #define CONFIG_SYS_HUSH_PARSER 268 269 #if defined(CONFIG_PCI) 270 /* 271 * General PCI 272 * Addresses are mapped 1-1. 273 */ 274 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 275 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 276 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 277 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 278 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 279 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 280 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 281 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 282 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 283 284 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 285 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 286 #endif 287 288 /* 289 * TSEC 290 */ 291 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 292 293 294 #define CONFIG_TSEC1 295 #ifdef CONFIG_TSEC1 296 #define CONFIG_HAS_ETH0 297 #define CONFIG_TSEC1_NAME "TSEC1" 298 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 299 #define TSEC1_PHY_ADDR 0x01 300 #define TSEC1_FLAGS 0 301 #define TSEC1_PHYIDX 0 302 #endif 303 304 /* Options are: TSEC[0-1] */ 305 #define CONFIG_ETHPRIME "TSEC1" 306 307 /* 308 * Environment 309 */ 310 #define CONFIG_ENV_IS_IN_FLASH 1 311 #define CONFIG_ENV_ADDR \ 312 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 313 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 314 #define CONFIG_ENV_SIZE 0x4000 315 /* Address and size of Redundant Environment Sector */ 316 #define CONFIG_ENV_OFFSET_REDUND \ 317 (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) 318 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 319 320 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 321 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 322 323 /* 324 * BOOTP options 325 */ 326 #define CONFIG_BOOTP_BOOTFILESIZE 327 #define CONFIG_BOOTP_BOOTPATH 328 #define CONFIG_BOOTP_GATEWAY 329 #define CONFIG_BOOTP_HOSTNAME 330 331 /* 332 * Command line configuration. 333 */ 334 #include <config_cmd_default.h> 335 336 #define CONFIG_CMD_DHCP 337 #define CONFIG_CMD_MII 338 #define CONFIG_CMD_PING 339 #define CONFIG_CMD_PCI 340 341 #define CONFIG_CMDLINE_EDITING 1 342 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 343 344 /* 345 * Miscellaneous configurable options 346 */ 347 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 348 #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ 349 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 350 351 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 352 #define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ 353 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg Buffer size */ 354 355 /* 356 * For booting Linux, the board info and command line data 357 * have to be in the first 256 MB of memory, since this is 358 * the maximum mapped by the Linux kernel during initialization. 359 */ 360 /* Initial Memory map for Linux*/ 361 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 362 363 /* 0x64050000 */ 364 #define CONFIG_SYS_HRCW_LOW (\ 365 0x20000000 /* reserved, must be set */ |\ 366 HRCWL_DDRCM |\ 367 HRCWL_CSB_TO_CLKIN_4X1 | \ 368 HRCWL_CORE_TO_CSB_2_5X1) 369 370 /* 0xa0600004 */ 371 #define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \ 372 HRCWH_PCI_ARBITER_ENABLE | \ 373 HRCWH_CORE_ENABLE | \ 374 HRCWH_FROM_0X00000100 | \ 375 HRCWH_BOOTSEQ_DISABLE |\ 376 HRCWH_SW_WATCHDOG_DISABLE |\ 377 HRCWH_ROM_LOC_LOCAL_16BIT | \ 378 HRCWH_TSEC1M_IN_MII | \ 379 HRCWH_BIG_ENDIAN | \ 380 HRCWH_LALE_EARLY) 381 382 /* System IO Config */ 383 #define CONFIG_SYS_SICRH (0x01000000 | \ 384 SICRH_ETSEC2_B | \ 385 SICRH_ETSEC2_C | \ 386 SICRH_ETSEC2_D | \ 387 SICRH_ETSEC2_E | \ 388 SICRH_ETSEC2_F | \ 389 SICRH_ETSEC2_G | \ 390 SICRH_TSOBI1 | \ 391 SICRH_TSOBI2) 392 /* 0x010fff03 */ 393 #define CONFIG_SYS_SICRL (SICRL_LBC | \ 394 SICRL_SPI_A | \ 395 SICRL_SPI_B | \ 396 SICRL_SPI_C | \ 397 SICRL_SPI_D | \ 398 SICRL_ETSEC2_A) 399 /* 0x33fc0003) */ 400 401 #define CONFIG_SYS_HID0_INIT 0x000000000 402 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 403 HID0_ENABLE_INSTRUCTION_CACHE) 404 405 #define CONFIG_SYS_HID2 HID2_HBE 406 407 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 408 409 /* DDR @ 0x00000000 */ 410 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW) 411 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 412 | BATU_BL_256M \ 413 | BATU_VS \ 414 | BATU_VP) 415 416 #if defined(CONFIG_PCI) 417 /* PCI @ 0x80000000 */ 418 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW) 419 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ 420 | BATU_BL_256M \ 421 | BATU_VS \ 422 | BATU_VP) 423 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ 424 | BATL_PP_RW \ 425 | BATL_CACHEINHIBIT \ 426 | BATL_GUARDEDSTORAGE) 427 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ 428 | BATU_BL_256M \ 429 | BATU_VS \ 430 | BATU_VP) 431 #else 432 #define CONFIG_SYS_IBAT1L (0) 433 #define CONFIG_SYS_IBAT1U (0) 434 #define CONFIG_SYS_IBAT2L (0) 435 #define CONFIG_SYS_IBAT2U (0) 436 #endif 437 438 /* PCI2 not supported on 8313 */ 439 #define CONFIG_SYS_IBAT3L (0) 440 #define CONFIG_SYS_IBAT3U (0) 441 #define CONFIG_SYS_IBAT4L (0) 442 #define CONFIG_SYS_IBAT4U (0) 443 444 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ 445 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ 446 | BATL_PP_RW \ 447 | BATL_CACHEINHIBIT \ 448 | BATL_GUARDEDSTORAGE) 449 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ 450 | BATU_BL_256M \ 451 | BATU_VS \ 452 | BATU_VP) 453 454 /* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ 455 #define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE) 456 #define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) 457 458 /* FPGA, SRAM, NAND @ 0x60000000 */ 459 #define CONFIG_SYS_IBAT7L (0x60000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE) 460 #define CONFIG_SYS_IBAT7U (0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP) 461 462 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 463 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 464 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 465 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 466 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 467 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 468 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 469 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 470 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 471 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 472 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 473 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 474 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 475 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 476 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 477 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 478 479 #define CONFIG_NETDEV eth0 480 481 #define CONFIG_HOSTNAME ve8313 482 #define CONFIG_UBOOTPATH ve8313/u-boot.bin 483 484 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 485 #define CONFIG_BAUDRATE 115200 486 487 #define CONFIG_EXTRA_ENV_SETTINGS \ 488 "netdev=" __stringify(CONFIG_NETDEV) "\0" \ 489 "ethprime=" __stringify(CONFIG_TSEC1_NAME) "\0" \ 490 "u-boot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 491 "u-boot_addr_r=100000\0" \ 492 "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ 493 "update=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \ 494 " +${filesize};" \ 495 "erase " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize};" \ 496 "cp.b ${u-boot_addr_r} " __stringify(CONFIG_SYS_FLASH_BASE) \ 497 " ${filesize};" \ 498 "protect on " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \ 499 500 #endif /* __CONFIG_H */ 501