1 /* 2 * Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* U-boot - Common settings for UniPhier Family */ 8 9 #ifndef __CONFIG_UNIPHIER_COMMON_H__ 10 #define __CONFIG_UNIPHIER_COMMON_H__ 11 12 #if defined(CONFIG_MACH_PH1_SLD3) 13 #define CONFIG_DDR_NUM_CH0 2 14 #define CONFIG_DDR_NUM_CH1 1 15 #define CONFIG_DDR_NUM_CH2 1 16 17 /* Physical start address of SDRAM */ 18 #define CONFIG_SDRAM0_BASE 0x80000000 19 #define CONFIG_SDRAM0_SIZE 0x20000000 20 #define CONFIG_SDRAM1_BASE 0xc0000000 21 #define CONFIG_SDRAM1_SIZE 0x20000000 22 #define CONFIG_SDRAM2_BASE 0xc0000000 23 #define CONFIG_SDRAM2_SIZE 0x10000000 24 #endif 25 26 #if defined(CONFIG_MACH_PH1_LD4) 27 #define CONFIG_DDR_NUM_CH0 1 28 #define CONFIG_DDR_NUM_CH1 1 29 30 /* Physical start address of SDRAM */ 31 #define CONFIG_SDRAM0_BASE 0x80000000 32 #define CONFIG_SDRAM0_SIZE 0x10000000 33 #define CONFIG_SDRAM1_BASE 0x90000000 34 #define CONFIG_SDRAM1_SIZE 0x10000000 35 #endif 36 37 #if defined(CONFIG_MACH_PH1_PRO4) 38 #define CONFIG_DDR_NUM_CH0 2 39 #define CONFIG_DDR_NUM_CH1 2 40 41 /* Physical start address of SDRAM */ 42 #define CONFIG_SDRAM0_BASE 0x80000000 43 #define CONFIG_SDRAM0_SIZE 0x20000000 44 #define CONFIG_SDRAM1_BASE 0xa0000000 45 #define CONFIG_SDRAM1_SIZE 0x20000000 46 #endif 47 48 #if defined(CONFIG_MACH_PH1_SLD8) 49 #define CONFIG_DDR_NUM_CH0 1 50 #define CONFIG_DDR_NUM_CH1 1 51 52 /* Physical start address of SDRAM */ 53 #define CONFIG_SDRAM0_BASE 0x80000000 54 #define CONFIG_SDRAM0_SIZE 0x10000000 55 #define CONFIG_SDRAM1_BASE 0x90000000 56 #define CONFIG_SDRAM1_SIZE 0x10000000 57 #endif 58 59 #define CONFIG_I2C_EEPROM 60 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 61 62 /* 63 * Support card address map 64 */ 65 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) 66 # define CONFIG_SUPPORT_CARD_BASE 0x03f00000 67 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000) 68 # define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00090000) 69 # define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x000b0000) 70 #endif 71 72 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD) 73 # define CONFIG_SUPPORT_CARD_BASE 0x08000000 74 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000) 75 # define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00401630) 76 # define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00200000) 77 #endif 78 79 #ifdef CONFIG_SYS_NS16550_SERIAL 80 #define CONFIG_SYS_NS16550 81 #define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE 82 #define CONFIG_SYS_NS16550_CLK 12288000 83 #define CONFIG_SYS_NS16550_REG_SIZE -2 84 #endif 85 86 /* TODO: move to Kconfig and device tree */ 87 #if 0 88 #define CONFIG_SYS_NS16550_SERIAL 89 #endif 90 91 #define CONFIG_SMC911X 92 93 #define CONFIG_SMC911X_BASE CONFIG_SUPPORT_CARD_ETHER_BASE 94 #define CONFIG_SMC911X_32_BIT 95 96 /*----------------------------------------------------------------------- 97 * MMU and Cache Setting 98 *----------------------------------------------------------------------*/ 99 100 /* Comment out the following to enable L1 cache */ 101 /* #define CONFIG_SYS_ICACHE_OFF */ 102 /* #define CONFIG_SYS_DCACHE_OFF */ 103 104 #define CONFIG_SYS_CACHELINE_SIZE 32 105 106 /* Comment out the following to enable L2 cache */ 107 #define CONFIG_UNIPHIER_L2CACHE_ON 108 109 #define CONFIG_DISPLAY_CPUINFO 110 #define CONFIG_DISPLAY_BOARDINFO 111 #define CONFIG_MISC_INIT_F 112 #define CONFIG_BOARD_EARLY_INIT_F 113 #define CONFIG_BOARD_EARLY_INIT_R 114 #define CONFIG_BOARD_LATE_INIT 115 116 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 117 118 #define CONFIG_TIMESTAMP 119 120 /* FLASH related */ 121 #define CONFIG_MTD_DEVICE 122 123 /* 124 * uncomment the following to disable FLASH related code. 125 */ 126 /* #define CONFIG_SYS_NO_FLASH */ 127 128 #define CONFIG_FLASH_CFI_DRIVER 129 #define CONFIG_SYS_FLASH_CFI 130 131 #define CONFIG_SYS_MAX_FLASH_SECT 256 132 #define CONFIG_SYS_MONITOR_BASE 0 133 #define CONFIG_SYS_FLASH_BASE 0 134 135 /* 136 * flash_toggle does not work for out supoort card. 137 * We need to use flash_status_poll. 138 */ 139 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL 140 141 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 142 143 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 144 145 /* serial console configuration */ 146 #define CONFIG_BAUDRATE 115200 147 148 #define CONFIG_SYS_GENERIC_BOARD 149 150 #if !defined(CONFIG_SPL_BUILD) 151 #define CONFIG_USE_ARCH_MEMSET 152 #define CONFIG_USE_ARCH_MEMCPY 153 #endif 154 155 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 156 157 #define CONFIG_CMDLINE_EDITING /* add command line history */ 158 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 159 /* Print Buffer Size */ 160 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 161 #define CONFIG_SYS_MAXARGS 16 /* max number of command */ 162 /* Boot Argument Buffer Size */ 163 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 164 165 #define CONFIG_CONS_INDEX 1 166 167 /* 168 * For NAND booting the environment is embedded in the U-Boot image. Please take 169 * look at the file board/amcc/canyonlands/u-boot-nand.lds for details. 170 */ 171 /* #define CONFIG_ENV_IS_IN_NAND */ 172 #define CONFIG_ENV_IS_NOWHERE 173 #define CONFIG_ENV_SIZE 0x2000 174 #define CONFIG_ENV_OFFSET 0x0 175 /* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */ 176 177 /* Time clock 1MHz */ 178 #define CONFIG_SYS_TIMER_RATE 1000000 179 180 /* 181 * By default, ARP timeout is 5 sec. 182 * The first ARP request does not seem to work. 183 * So we need to retry ARP request anyway. 184 * We want to shrink the interval until the second ARP request. 185 */ 186 #define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */ 187 188 #define CONFIG_SYS_MAX_NAND_DEVICE 1 189 #define CONFIG_SYS_NAND_MAX_CHIPS 2 190 #define CONFIG_SYS_NAND_ONFI_DETECTION 191 192 #define CONFIG_NAND_DENALI_ECC_SIZE 1024 193 194 #ifdef CONFIG_MACH_PH1_SLD3 195 #define CONFIG_SYS_NAND_REGS_BASE 0xf8100000 196 #define CONFIG_SYS_NAND_DATA_BASE 0xf8000000 197 #else 198 #define CONFIG_SYS_NAND_REGS_BASE 0x68100000 199 #define CONFIG_SYS_NAND_DATA_BASE 0x68000000 200 #endif 201 202 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10) 203 204 #define CONFIG_SYS_NAND_USE_FLASH_BBT 205 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 206 207 /* USB */ 208 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 209 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 4 210 #define CONFIG_CMD_FAT 211 #define CONFIG_FAT_WRITE 212 #define CONFIG_DOS_PARTITION 213 214 /* memtest works on */ 215 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 216 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000) 217 218 #define CONFIG_BOOTDELAY 3 219 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ 220 221 /* 222 * Network Configuration 223 */ 224 #define CONFIG_SERVERIP 192.168.11.1 225 #define CONFIG_IPADDR 192.168.11.10 226 #define CONFIG_GATEWAYIP 192.168.11.1 227 #define CONFIG_NETMASK 255.255.255.0 228 229 #define CONFIG_LOADADDR 0x84000000 230 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 231 232 #define CONFIG_CMDLINE_EDITING /* add command line history */ 233 234 #define CONFIG_BOOTCOMMAND "run $bootmode" 235 236 #define CONFIG_ROOTPATH "/nfs/root/path" 237 #define CONFIG_NFSBOOTCOMMAND \ 238 "setenv bootargs $bootargs root=/dev/nfs rw " \ 239 "nfsroot=$serverip:$rootpath " \ 240 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \ 241 "tftpboot; bootm;" 242 243 #define CONFIG_BOOTARGS " earlyprintk loglevel=8" 244 245 #ifdef CONFIG_FIT 246 #define CONFIG_BOOTFILE "fitImage" 247 #define LINUXBOOT_ENV_SETTINGS \ 248 "fit_addr=0x00100000\0" \ 249 "fit_addr_r=0x84100000\0" \ 250 "fit_size=0x00f00000\0" \ 251 "norboot=run add_default_bootargs &&" \ 252 "bootm $fit_addr\0" \ 253 "nandboot=run add_default_bootargs &&" \ 254 "nand read $fit_addr_r $fit_addr $fit_size &&" \ 255 "bootm $fit_addr_r\0" \ 256 "tftpboot=run add_default_bootargs &&" \ 257 "tftpboot $fit_addr_r $bootfile &&" \ 258 "bootm $fit_addr_r\0" 259 #else 260 #define CONFIG_BOOTFILE "uImage" 261 #define LINUXBOOT_ENV_SETTINGS \ 262 "fdt_addr=0x00100000\0" \ 263 "fdt_addr_r=0x84100000\0" \ 264 "fdt_size=0x00008000\0" \ 265 "fdt_file=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ 266 "kernel_addr=0x00200000\0" \ 267 "kernel_addr_r=0x84200000\0" \ 268 "kernel_size=0x00800000\0" \ 269 "ramdisk_addr=0x00a00000\0" \ 270 "ramdisk_addr_r=0x84a00000\0" \ 271 "ramdisk_size=0x00600000\0" \ 272 "ramdisk_file=rootfs.cpio.uboot\0" \ 273 "norboot=run add_default_bootargs &&" \ 274 "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \ 275 "nandboot=run add_default_bootargs &&" \ 276 "nand read $kernel_addr_r $kernel_addr $kernel_size &&" \ 277 "nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \ 278 "nand read $fdt_addr_r $fdt_addr $fdt_size &&" \ 279 "bootm $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \ 280 "tftpboot=run add_default_bootargs &&" \ 281 "tftpboot $kernel_addr_r $bootfile &&" \ 282 "tftpboot $ramdisk_addr_r $ramdisk_file &&" \ 283 "tftpboot $fdt_addr_r $fdt_file &&" \ 284 "bootm $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" 285 #endif 286 287 #define CONFIG_EXTRA_ENV_SETTINGS \ 288 "netdev=eth0\0" \ 289 "verify=n\0" \ 290 "nandupdate=nand erase 0 0x00100000 &&" \ 291 "tftpboot u-boot-spl.bin &&" \ 292 "nand write $loadaddr 0 0x00010000 &&" \ 293 "tftpboot u-boot-dtb.img &&" \ 294 "nand write $loadaddr 0x00010000 0x000f0000\0" \ 295 "add_default_bootargs=setenv bootargs $bootargs" \ 296 " console=ttyS0,$baudrate\0" \ 297 LINUXBOOT_ENV_SETTINGS 298 299 /* Open Firmware flat tree */ 300 #define CONFIG_OF_LIBFDT 301 302 #define CONFIG_HAVE_ARM_SECURE 303 304 /* Memory Size & Mapping */ 305 #define CONFIG_SYS_SDRAM_BASE CONFIG_SDRAM0_BASE 306 307 #if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE 308 /* Thre is no memory hole */ 309 #define CONFIG_NR_DRAM_BANKS 1 310 #define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE) 311 #else 312 #define CONFIG_NR_DRAM_BANKS 2 313 #define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE) 314 #endif 315 316 #if defined(CONFIG_MACH_PH1_SLD3) || defined(CONFIG_MACH_PH1_LD4) || \ 317 defined(CONFIG_MACH_PH1_SLD8) 318 #define CONFIG_SPL_TEXT_BASE 0x00040000 319 #endif 320 #if defined(CONFIG_MACH_PH1_PRO4) 321 #define CONFIG_SPL_TEXT_BASE 0x00100000 322 #endif 323 324 #define CONFIG_SPL_STACK (0x0ff08000) 325 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE) 326 327 #define CONFIG_PANIC_HANG 328 329 #define CONFIG_SPL_FRAMEWORK 330 #define CONFIG_SPL_SERIAL_SUPPORT 331 #define CONFIG_SPL_NAND_SUPPORT 332 333 #define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */ 334 #define CONFIG_SPL_LIBGENERIC_SUPPORT 335 336 #define CONFIG_SPL_BOARD_INIT 337 338 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000 339 340 #define CONFIG_SPL_MAX_FOOTPRINT 0x10000 341 342 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */ 343