1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2006-2008 4 * Texas Instruments. 5 * Richard Woodruff <r-woodruff2@ti.com> 6 * Syed Mohammed Khasim <x0khasim@ti.com> 7 * 8 * (C) Copyright 2012 9 * Corscience GmbH & Co. KG 10 * Thomas Weber <weber@corscience.de> 11 * 12 * Configuration settings for the Tricorder board. 13 */ 14 15 #ifndef __CONFIG_H 16 #define __CONFIG_H 17 18 #define CONFIG_MACH_TYPE MACH_TYPE_TRICORDER 19 /* 20 * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM 21 * 64 bytes before this address should be set aside for u-boot.img's 22 * header. That is 0x800FFFC0--0x80100000 should not be used for any 23 * other needs. 24 */ 25 26 #include <asm/arch/cpu.h> /* get chip and board defs */ 27 #include <asm/arch/omap.h> 28 29 /* Clock Defines */ 30 #define V_OSCK 26000000 /* Clock output from T2 */ 31 #define V_SCLK (V_OSCK >> 1) 32 33 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 34 #define CONFIG_SETUP_MEMORY_TAGS 35 #define CONFIG_INITRD_TAG 36 #define CONFIG_REVISION_TAG 37 38 /* Size of malloc() pool */ 39 #define CONFIG_SYS_MALLOC_LEN (1024*1024) 40 41 /* Hardware drivers */ 42 43 /* NS16550 Configuration */ 44 #define CONFIG_SYS_NS16550_SERIAL 45 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 46 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 47 48 /* select serial console configuration */ 49 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 50 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 51 115200} 52 53 /* I2C */ 54 #define CONFIG_SYS_I2C 55 56 57 /* EEPROM */ 58 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 59 #define CONFIG_SYS_EEPROM_BUS_NUM 1 60 61 /* TWL4030 */ 62 63 /* Board NAND Info */ 64 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 65 /* to access nand at */ 66 /* CS0 */ 67 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ 68 /* devices */ 69 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 70 #define CONFIG_SYS_NAND_MAX_ECCPOS 56 71 72 /* needed for ubi */ 73 74 /* Environment information (this is the common part) */ 75 76 77 /* hang() the board on panic() */ 78 79 /* environment placement (for NAND), is different for FLASHCARD but does not 80 * harm there */ 81 #define CONFIG_ENV_OFFSET 0x120000 /* env start */ 82 #define CONFIG_ENV_OFFSET_REDUND 0x2A0000 /* redundant env start */ 83 #define CONFIG_ENV_SIZE (16 << 10) /* use 16KiB for env */ 84 #define CONFIG_ENV_RANGE (384 << 10) /* allow badblocks in env */ 85 86 /* the loadaddr is the same as CONFIG_SYS_LOAD_ADDR, unfortunately the defiend 87 * value can not be used here! */ 88 #define CONFIG_LOADADDR 0x82000000 89 90 #define CONFIG_COMMON_ENV_SETTINGS \ 91 "console=ttyO2,115200n8\0" \ 92 "mmcdev=0\0" \ 93 "vram=3M\0" \ 94 "defaultdisplay=lcd\0" \ 95 "kernelopts=mtdoops.mtddev=3\0" \ 96 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ 97 "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ 98 "commonargs=" \ 99 "setenv bootargs console=${console} " \ 100 "${mtdparts} " \ 101 "${kernelopts} " \ 102 "vt.global_cursor_default=0 " \ 103 "vram=${vram} " \ 104 "omapdss.def_disp=${defaultdisplay}\0" 105 106 #define CONFIG_BOOTCOMMAND "run autoboot" 107 108 /* specific environment settings for different use cases 109 * FLASHCARD: used to run a rdimage from sdcard to program the device 110 * 'NORMAL': used to boot kernel from sdcard, nand, ... 111 * 112 * The main aim for the FLASHCARD skin is to have an embedded environment 113 * which will not be influenced by any data already on the device. 114 */ 115 #ifdef CONFIG_FLASHCARD 116 /* the rdaddr is 16 MiB before the loadaddr */ 117 #define CONFIG_ENV_RDADDR "rdaddr=0x81000000\0" 118 119 #define CONFIG_EXTRA_ENV_SETTINGS \ 120 CONFIG_COMMON_ENV_SETTINGS \ 121 CONFIG_ENV_RDADDR \ 122 "autoboot=" \ 123 "run commonargs; " \ 124 "setenv bootargs ${bootargs} " \ 125 "flashy_updateimg=/dev/mmcblk0p1:corscience_update.img " \ 126 "rdinit=/sbin/init; " \ 127 "mmc dev ${mmcdev}; mmc rescan; " \ 128 "fatload mmc ${mmcdev} ${loadaddr} uImage; " \ 129 "fatload mmc ${mmcdev} ${rdaddr} uRamdisk; " \ 130 "bootm ${loadaddr} ${rdaddr}\0" 131 132 #else /* CONFIG_FLASHCARD */ 133 134 #define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */ 135 136 #define CONFIG_EXTRA_ENV_SETTINGS \ 137 CONFIG_COMMON_ENV_SETTINGS \ 138 "mmcargs=" \ 139 "run commonargs; " \ 140 "setenv bootargs ${bootargs} " \ 141 "root=/dev/mmcblk0p2 " \ 142 "rootwait " \ 143 "rw\0" \ 144 "nandargs=" \ 145 "run commonargs; " \ 146 "setenv bootargs ${bootargs} " \ 147 "root=ubi0:root " \ 148 "ubi.mtd=7 " \ 149 "rootfstype=ubifs " \ 150 "ro\0" \ 151 "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 152 "bootscript=echo Running bootscript from mmc ...; " \ 153 "source ${loadaddr}\0" \ 154 "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ 155 "mmcboot=echo Booting from mmc ...; " \ 156 "run mmcargs; " \ 157 "bootm ${loadaddr}\0" \ 158 "loaduimage_ubi=ubi part ubi; " \ 159 "ubifsmount ubi:root; " \ 160 "ubifsload ${loadaddr} /boot/uImage\0" \ 161 "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \ 162 "nandboot=echo Booting from nand ...; " \ 163 "run nandargs; " \ 164 "run loaduimage_nand; " \ 165 "bootm ${loadaddr}\0" \ 166 "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \ 167 "if run loadbootscript; then " \ 168 "run bootscript; " \ 169 "else " \ 170 "if run loaduimage; then " \ 171 "run mmcboot; " \ 172 "else run nandboot; " \ 173 "fi; " \ 174 "fi; " \ 175 "else run nandboot; fi\0" 176 177 #endif /* CONFIG_FLASHCARD */ 178 179 /* Miscellaneous configurable options */ 180 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 181 182 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x00000000) 183 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ 184 0x07000000) /* 112 MB */ 185 186 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000) 187 188 /* 189 * OMAP3 has 12 GP timers, they can be driven by the system clock 190 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 191 * This rate is divided by a local divisor. 192 */ 193 #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) 194 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 195 196 /* Physical Memory Map */ 197 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 198 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 199 200 /* NAND and environment organization */ 201 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ 202 203 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 204 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 205 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 206 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 207 CONFIG_SYS_INIT_RAM_SIZE - \ 208 GENERATED_GBL_DATA_SIZE) 209 210 /* SRAM config */ 211 #define CONFIG_SYS_SRAM_START 0x40200000 212 #define CONFIG_SYS_SRAM_SIZE 0x10000 213 214 /* Defines for SPL */ 215 216 #define CONFIG_SPL_NAND_BASE 217 #define CONFIG_SPL_NAND_DRIVERS 218 #define CONFIG_SPL_NAND_ECC 219 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 220 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 221 222 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ 223 #define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ 224 CONFIG_SPL_TEXT_BASE) 225 226 #define CONFIG_SPL_BSS_START_ADDR 0x80000000 /*CONFIG_SYS_SDRAM_BASE*/ 227 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 228 229 /* NAND boot config */ 230 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 231 #define CONFIG_SYS_NAND_PAGE_COUNT 64 232 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 233 #define CONFIG_SYS_NAND_OOBSIZE 64 234 #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) 235 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS 236 #define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \ 237 13, 14, 16, 17, 18, 19, 20, 21, 22, \ 238 23, 24, 25, 26, 27, 28, 30, 31, 32, \ 239 33, 34, 35, 36, 37, 38, 39, 40, 41, \ 240 42, 44, 45, 46, 47, 48, 49, 50, 51, \ 241 52, 53, 54, 55, 56} 242 243 #define CONFIG_SYS_NAND_ECCSIZE 512 244 #define CONFIG_SYS_NAND_ECCBYTES 13 245 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW 246 247 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 248 249 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000 250 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x100000 251 252 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 253 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ 254 255 #define CONFIG_SYS_MEMTEST_SCRATCH 0x81000000 256 #endif /* __CONFIG_H */ 257