1 /* 2 * (C) Copyright 2006-2008 3 * Texas Instruments. 4 * Richard Woodruff <r-woodruff2@ti.com> 5 * Syed Mohammed Khasim <x0khasim@ti.com> 6 * 7 * (C) Copyright 2012 8 * Corscience GmbH & Co. KG 9 * Thomas Weber <weber@corscience.de> 10 * 11 * Configuration settings for the Tricorder board. 12 * 13 * SPDX-License-Identifier: GPL-2.0+ 14 */ 15 16 #ifndef __CONFIG_H 17 #define __CONFIG_H 18 19 #define CONFIG_SYS_CACHELINE_SIZE 64 20 21 /* High Level Configuration Options */ 22 #define CONFIG_SYS_THUMB_BUILD 23 #define CONFIG_OMAP /* in a TI OMAP core */ 24 #define CONFIG_OMAP_COMMON 25 /* Common ARM Erratas */ 26 #define CONFIG_ARM_ERRATA_454179 27 #define CONFIG_ARM_ERRATA_430973 28 #define CONFIG_ARM_ERRATA_621766 29 30 #define CONFIG_MACH_TYPE MACH_TYPE_TRICORDER 31 /* 32 * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM 33 * 64 bytes before this address should be set aside for u-boot.img's 34 * header. That is 0x800FFFC0--0x80100000 should not be used for any 35 * other needs. 36 */ 37 #define CONFIG_SYS_TEXT_BASE 0x80100000 38 39 #define CONFIG_SDRC /* The chip has SDRC controller */ 40 41 #include <asm/arch/cpu.h> /* get chip and board defs */ 42 #include <asm/arch/omap.h> 43 44 /* Display CPU and Board information */ 45 #define CONFIG_DISPLAY_CPUINFO 46 #define CONFIG_DISPLAY_BOARDINFO 47 48 #define CONFIG_SILENT_CONSOLE 49 #define CONFIG_ZERO_BOOTDELAY_CHECK 50 51 /* Clock Defines */ 52 #define V_OSCK 26000000 /* Clock output from T2 */ 53 #define V_SCLK (V_OSCK >> 1) 54 55 #define CONFIG_MISC_INIT_R 56 57 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 58 #define CONFIG_SETUP_MEMORY_TAGS 59 #define CONFIG_INITRD_TAG 60 #define CONFIG_REVISION_TAG 61 62 /* Size of malloc() pool */ 63 #define CONFIG_SYS_MALLOC_LEN (1024*1024) 64 65 /* Hardware drivers */ 66 67 /* GPIO support */ 68 #define CONFIG_OMAP_GPIO 69 70 /* GPIO banks */ 71 #define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 are in GPIO bank 2 */ 72 73 /* LED support */ 74 #define CONFIG_STATUS_LED 75 #define CONFIG_BOARD_SPECIFIC_LED 76 #define CONFIG_CMD_LED /* LED command */ 77 #define STATUS_LED_BIT (1 << 0) 78 #define STATUS_LED_STATE STATUS_LED_ON 79 #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) 80 #define STATUS_LED_BIT1 (1 << 1) 81 #define STATUS_LED_STATE1 STATUS_LED_ON 82 #define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) 83 #define STATUS_LED_BIT2 (1 << 2) 84 #define STATUS_LED_STATE2 STATUS_LED_ON 85 #define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2) 86 87 /* NS16550 Configuration */ 88 #define CONFIG_SYS_NS16550_SERIAL 89 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 90 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 91 92 /* select serial console configuration */ 93 #define CONFIG_CONS_INDEX 3 94 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 95 #define CONFIG_SERIAL3 3 96 #define CONFIG_BAUDRATE 115200 97 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 98 115200} 99 100 /* MMC */ 101 #define CONFIG_GENERIC_MMC 102 #define CONFIG_MMC 103 #define CONFIG_OMAP_HSMMC 104 #define CONFIG_DOS_PARTITION 105 106 /* I2C */ 107 #define CONFIG_SYS_I2C 108 #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 109 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 110 #define CONFIG_SYS_I2C_OMAP34XX 111 112 113 /* EEPROM */ 114 #define CONFIG_CMD_EEPROM 115 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 116 #define CONFIG_SYS_EEPROM_BUS_NUM 1 117 118 /* TWL4030 */ 119 #define CONFIG_TWL4030_POWER 120 #define CONFIG_TWL4030_LED 121 122 /* Board NAND Info */ 123 #define CONFIG_SYS_NO_FLASH /* no NOR flash */ 124 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 125 #define MTDIDS_DEFAULT "nand0=omap2-nand.0" 126 #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \ 127 "128k(SPL)," \ 128 "1m(u-boot)," \ 129 "384k(u-boot-env1)," \ 130 "1152k(mtdoops)," \ 131 "384k(u-boot-env2)," \ 132 "5m(kernel)," \ 133 "2m(fdt)," \ 134 "-(ubi)" 135 136 #define CONFIG_NAND_OMAP_GPMC 137 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ 138 /* to access nand */ 139 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 140 /* to access nand at */ 141 /* CS0 */ 142 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ 143 /* devices */ 144 #define CONFIG_BCH 145 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 146 #define CONFIG_SYS_NAND_MAX_ECCPOS 56 147 148 /* commands to include */ 149 #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ 150 #define CONFIG_CMD_NAND /* NAND support */ 151 #define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */ 152 #define CONFIG_CMD_UBI /* UBI commands */ 153 #define CONFIG_CMD_UBIFS /* UBIFS commands */ 154 #define CONFIG_LZO /* LZO is needed for UBIFS */ 155 156 #undef CONFIG_CMD_JFFS2 /* JFFS2 Support */ 157 158 /* needed for ubi */ 159 #define CONFIG_RBTREE 160 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 161 #define CONFIG_MTD_PARTITIONS 162 163 /* Environment information (this is the common part) */ 164 165 166 /* hang() the board on panic() */ 167 #define CONFIG_PANIC_HANG 168 169 /* environment placement (for NAND), is different for FLASHCARD but does not 170 * harm there */ 171 #define CONFIG_ENV_OFFSET 0x120000 /* env start */ 172 #define CONFIG_ENV_OFFSET_REDUND 0x2A0000 /* redundant env start */ 173 #define CONFIG_ENV_SIZE (16 << 10) /* use 16KiB for env */ 174 #define CONFIG_ENV_RANGE (384 << 10) /* allow badblocks in env */ 175 176 /* the loadaddr is the same as CONFIG_SYS_LOAD_ADDR, unfortunately the defiend 177 * value can not be used here! */ 178 #define CONFIG_LOADADDR 0x82000000 179 180 #define CONFIG_COMMON_ENV_SETTINGS \ 181 "console=ttyO2,115200n8\0" \ 182 "mmcdev=0\0" \ 183 "vram=3M\0" \ 184 "defaultdisplay=lcd\0" \ 185 "kernelopts=mtdoops.mtddev=3\0" \ 186 "mtdparts=" MTDPARTS_DEFAULT "\0" \ 187 "mtdids=" MTDIDS_DEFAULT "\0" \ 188 "commonargs=" \ 189 "setenv bootargs console=${console} " \ 190 "${mtdparts} " \ 191 "${kernelopts} " \ 192 "vt.global_cursor_default=0 " \ 193 "vram=${vram} " \ 194 "omapdss.def_disp=${defaultdisplay}\0" 195 196 #define CONFIG_BOOTCOMMAND "run autoboot" 197 198 /* specific environment settings for different use cases 199 * FLASHCARD: used to run a rdimage from sdcard to program the device 200 * 'NORMAL': used to boot kernel from sdcard, nand, ... 201 * 202 * The main aim for the FLASHCARD skin is to have an embedded environment 203 * which will not be influenced by any data already on the device. 204 */ 205 #ifdef CONFIG_FLASHCARD 206 207 #define CONFIG_ENV_IS_NOWHERE 208 209 /* the rdaddr is 16 MiB before the loadaddr */ 210 #define CONFIG_ENV_RDADDR "rdaddr=0x81000000\0" 211 212 #define CONFIG_EXTRA_ENV_SETTINGS \ 213 CONFIG_COMMON_ENV_SETTINGS \ 214 CONFIG_ENV_RDADDR \ 215 "autoboot=" \ 216 "run commonargs; " \ 217 "setenv bootargs ${bootargs} " \ 218 "flashy_updateimg=/dev/mmcblk0p1:corscience_update.img " \ 219 "rdinit=/sbin/init; " \ 220 "mmc dev ${mmcdev}; mmc rescan; " \ 221 "fatload mmc ${mmcdev} ${loadaddr} uImage; " \ 222 "fatload mmc ${mmcdev} ${rdaddr} uRamdisk; " \ 223 "bootm ${loadaddr} ${rdaddr}\0" 224 225 #else /* CONFIG_FLASHCARD */ 226 227 #define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */ 228 229 #define CONFIG_ENV_IS_IN_NAND 230 231 #define CONFIG_EXTRA_ENV_SETTINGS \ 232 CONFIG_COMMON_ENV_SETTINGS \ 233 "mmcargs=" \ 234 "run commonargs; " \ 235 "setenv bootargs ${bootargs} " \ 236 "root=/dev/mmcblk0p2 " \ 237 "rootwait " \ 238 "rw\0" \ 239 "nandargs=" \ 240 "run commonargs; " \ 241 "setenv bootargs ${bootargs} " \ 242 "root=ubi0:root " \ 243 "ubi.mtd=7 " \ 244 "rootfstype=ubifs " \ 245 "ro\0" \ 246 "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 247 "bootscript=echo Running bootscript from mmc ...; " \ 248 "source ${loadaddr}\0" \ 249 "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ 250 "mmcboot=echo Booting from mmc ...; " \ 251 "run mmcargs; " \ 252 "bootm ${loadaddr}\0" \ 253 "loaduimage_ubi=ubi part ubi; " \ 254 "ubifsmount ubi:root; " \ 255 "ubifsload ${loadaddr} /boot/uImage\0" \ 256 "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \ 257 "nandboot=echo Booting from nand ...; " \ 258 "run nandargs; " \ 259 "run loaduimage_nand; " \ 260 "bootm ${loadaddr}\0" \ 261 "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \ 262 "if run loadbootscript; then " \ 263 "run bootscript; " \ 264 "else " \ 265 "if run loaduimage; then " \ 266 "run mmcboot; " \ 267 "else run nandboot; " \ 268 "fi; " \ 269 "fi; " \ 270 "else run nandboot; fi\0" 271 272 #endif /* CONFIG_FLASHCARD */ 273 274 /* Miscellaneous configurable options */ 275 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 276 #define CONFIG_CMDLINE_EDITING /* enable cmdline history */ 277 #define CONFIG_AUTO_COMPLETE 278 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 279 /* Print Buffer Size */ 280 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 281 sizeof(CONFIG_SYS_PROMPT) + 16) 282 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 283 284 /* Boot Argument Buffer Size */ 285 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 286 287 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x00000000) 288 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ 289 0x07000000) /* 112 MB */ 290 291 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000) 292 293 /* 294 * OMAP3 has 12 GP timers, they can be driven by the system clock 295 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 296 * This rate is divided by a local divisor. 297 */ 298 #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) 299 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 300 301 /* Physical Memory Map */ 302 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 303 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 304 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 305 306 /* NAND and environment organization */ 307 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ 308 309 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 310 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 311 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 312 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 313 CONFIG_SYS_INIT_RAM_SIZE - \ 314 GENERATED_GBL_DATA_SIZE) 315 316 /* SRAM config */ 317 #define CONFIG_SYS_SRAM_START 0x40200000 318 #define CONFIG_SYS_SRAM_SIZE 0x10000 319 320 /* Defines for SPL */ 321 #define CONFIG_SPL_FRAMEWORK 322 #define CONFIG_SPL_NAND_SIMPLE 323 324 #define CONFIG_SPL_BOARD_INIT 325 #define CONFIG_SPL_GPIO_SUPPORT 326 #define CONFIG_SPL_LIBCOMMON_SUPPORT 327 #define CONFIG_SPL_LIBDISK_SUPPORT 328 #define CONFIG_SPL_I2C_SUPPORT 329 #define CONFIG_SPL_LIBGENERIC_SUPPORT 330 #define CONFIG_SPL_SERIAL_SUPPORT 331 #define CONFIG_SPL_POWER_SUPPORT 332 #define CONFIG_SPL_NAND_SUPPORT 333 #define CONFIG_SPL_NAND_BASE 334 #define CONFIG_SPL_NAND_DRIVERS 335 #define CONFIG_SPL_NAND_ECC 336 #define CONFIG_SPL_MMC_SUPPORT 337 #define CONFIG_SPL_FAT_SUPPORT 338 #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" 339 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 340 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 341 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ 342 343 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ 344 #define CONFIG_SPL_MAX_SIZE (57 * 1024) /* 7 KB for stack */ 345 346 #define CONFIG_SPL_BSS_START_ADDR 0x80000000 /*CONFIG_SYS_SDRAM_BASE*/ 347 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 348 349 /* NAND boot config */ 350 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 351 #define CONFIG_SYS_NAND_PAGE_COUNT 64 352 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 353 #define CONFIG_SYS_NAND_OOBSIZE 64 354 #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) 355 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS 356 #define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \ 357 13, 14, 16, 17, 18, 19, 20, 21, 22, \ 358 23, 24, 25, 26, 27, 28, 30, 31, 32, \ 359 33, 34, 35, 36, 37, 38, 39, 40, 41, \ 360 42, 44, 45, 46, 47, 48, 49, 50, 51, \ 361 52, 53, 54, 55, 56} 362 363 #define CONFIG_SYS_NAND_ECCSIZE 512 364 #define CONFIG_SYS_NAND_ECCBYTES 13 365 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW 366 367 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 368 369 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000 370 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x100000 371 372 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 373 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ 374 375 #define CONFIG_SYS_ALT_MEMTEST 376 #define CONFIG_SYS_MEMTEST_SCRATCH 0x81000000 377 #endif /* __CONFIG_H */ 378