1 /* 2 * Copyright (C) 2013, 2014, 2017 Markus Niebel <Markus.Niebel@tq-group.com> 3 * 4 * Configuration settings for the TQ Systems TQMa6<Q,D,DL,S> module. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #include <linux/kconfig.h> 13 /* SPL */ 14 /* #if defined(CONFIG_SPL_BUILD) */ 15 /* common IMX6 SPL configuration */ 16 #include "imx6_spl.h" 17 18 /* #endif */ 19 20 /* place code in last 4 MiB of RAM */ 21 #if defined(CONFIG_TQMA6S) 22 #define CONFIG_SYS_TEXT_BASE 0x2fc00000 23 #elif defined(CONFIG_TQMA6Q) || defined(CONFIG_TQMA6DL) 24 #define CONFIG_SYS_TEXT_BASE 0x4fc00000 25 #endif 26 27 #include "mx6_common.h" 28 29 #if defined(CONFIG_TQMA6S) 30 #define PHYS_SDRAM_SIZE (512u * SZ_1M) 31 #elif defined(CONFIG_TQMA6DL) 32 #define PHYS_SDRAM_SIZE (SZ_1G) 33 #elif defined(CONFIG_TQMA6Q) 34 #define PHYS_SDRAM_SIZE (SZ_1G) 35 #endif 36 37 #define CONFIG_MXC_UART 38 39 /* SPI */ 40 #define CONFIG_MXC_SPI 41 42 /* SPI Flash */ 43 44 #define TQMA6_SPI_FLASH_SECTOR_SIZE SZ_64K 45 46 #define CONFIG_SF_DEFAULT_BUS 0 47 #define CONFIG_SF_DEFAULT_CS 0 48 #define CONFIG_SF_DEFAULT_SPEED 50000000 49 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) 50 51 /* I2C Configs */ 52 #define CONFIG_SYS_I2C 53 #define CONFIG_SYS_I2C_MXC 54 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 55 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 56 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 57 #define CONFIG_I2C_MULTI_BUS 58 #define CONFIG_SYS_I2C_SPEED 100000 59 60 /* I2C EEPROM (M24C64) */ 61 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 62 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 63 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS 5 /* 32 Bytes */ 64 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS 20 65 66 #define CONFIG_POWER 67 #define CONFIG_POWER_I2C 68 #define CONFIG_POWER_PFUZE100 69 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 70 #define TQMA6_PFUZE100_I2C_BUS 2 71 72 /* MMC Configs */ 73 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 74 75 /* USB Configs */ 76 #define CONFIG_USB_HOST_ETHER 77 #define CONFIG_USB_ETHER_SMSC95XX 78 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 79 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 80 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ 81 82 #define CONFIG_FEC_MXC 83 #define IMX_FEC_BASE ENET_BASE_ADDR 84 #define CONFIG_PHYLIB 85 #define CONFIG_MII 86 87 #define CONFIG_ARP_TIMEOUT 200UL 88 89 #define CONFIG_ENV_SIZE (SZ_8K) 90 /* Size of malloc() pool */ 91 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * SZ_1M) 92 93 #if defined(CONFIG_TQMA6X_MMC_BOOT) 94 95 #define CONFIG_ENV_IS_IN_MMC 96 #define TQMA6_UBOOT_OFFSET SZ_1K 97 #define TQMA6_UBOOT_SECTOR_START 0x2 98 #define TQMA6_UBOOT_SECTOR_COUNT 0x7fe 99 100 #define CONFIG_ENV_OFFSET SZ_1M 101 #define CONFIG_SYS_MMC_ENV_DEV 0 102 103 #define TQMA6_FDT_OFFSET (2 * SZ_1M) 104 #define TQMA6_FDT_SECTOR_START 0x1000 105 #define TQMA6_FDT_SECTOR_COUNT 0x800 106 107 #define TQMA6_KERNEL_SECTOR_START 0x2000 108 #define TQMA6_KERNEL_SECTOR_COUNT 0x2000 109 110 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \ 111 "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0" \ 112 "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \ 113 "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \ 114 "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \ 115 "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \ 116 "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \ 117 "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \ 118 "loadimage=mmc dev ${mmcdev}; " \ 119 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0" \ 120 "loadfdt=mmc dev ${mmcdev}; " \ 121 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0" \ 122 "update_uboot=if tftp ${uboot}; then " \ 123 "if itest ${filesize} > 0; then " \ 124 "mmc dev ${mmcdev}; mmc rescan; " \ 125 "setexpr blkc ${filesize} + 0x1ff; " \ 126 "setexpr blkc ${blkc} / 0x200; " \ 127 "if itest ${blkc} <= ${uboot_size}; then " \ 128 "mmc write ${loadaddr} ${uboot_start} " \ 129 "${blkc}; " \ 130 "fi; " \ 131 "fi; fi; " \ 132 "setenv filesize; setenv blkc \0" \ 133 "update_kernel=run kernel_name; " \ 134 "if tftp ${kernel}; then " \ 135 "if itest ${filesize} > 0; then " \ 136 "mmc dev ${mmcdev}; mmc rescan; " \ 137 "setexpr blkc ${filesize} + 0x1ff; " \ 138 "setexpr blkc ${blkc} / 0x200; " \ 139 "if itest ${blkc} <= ${kernel_size}; then " \ 140 "mmc write ${loadaddr} " \ 141 "${kernel_start} ${blkc}; " \ 142 "fi; " \ 143 "fi; " \ 144 "fi; " \ 145 "setenv filesize; setenv blkc \0" \ 146 "update_fdt=if tftp ${fdt_file}; then " \ 147 "if itest ${filesize} > 0; then " \ 148 "mmc dev ${mmcdev}; mmc rescan; " \ 149 "setexpr blkc ${filesize} + 0x1ff; " \ 150 "setexpr blkc ${blkc} / 0x200; " \ 151 "if itest ${blkc} <= ${fdt_size}; then " \ 152 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \ 153 "fi; " \ 154 "fi; fi; " \ 155 "setenv filesize; setenv blkc \0" \ 156 157 #define CONFIG_BOOTCOMMAND \ 158 "run mmcboot; run netboot; run panicboot" 159 160 #elif defined(CONFIG_TQMA6X_SPI_BOOT) 161 162 #define TQMA6_UBOOT_OFFSET 0x400 163 #define TQMA6_UBOOT_SECTOR_START 0x0 164 /* max u-boot size: 512k */ 165 #define TQMA6_UBOOT_SECTOR_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE 166 #define TQMA6_UBOOT_SECTOR_COUNT 0x8 167 #define TQMA6_UBOOT_SIZE (TQMA6_UBOOT_SECTOR_SIZE * \ 168 TQMA6_UBOOT_SECTOR_COUNT) 169 170 #define CONFIG_ENV_IS_IN_SPI_FLASH 171 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 172 #define CONFIG_ENV_OFFSET (TQMA6_UBOOT_SIZE) 173 #define CONFIG_ENV_SECT_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE 174 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 175 CONFIG_ENV_SECT_SIZE) 176 177 #define CONFIG_ENV_SPI_BUS (CONFIG_SF_DEFAULT_BUS) 178 #define CONFIG_ENV_SPI_CS (CONFIG_SF_DEFAULT_CS) 179 #define CONFIG_ENV_SPI_MAX_HZ (CONFIG_SF_DEFAULT_SPEED) 180 #define CONFIG_ENV_SPI_MODE (CONFIG_SF_DEFAULT_MODE) 181 182 #define TQMA6_FDT_OFFSET (CONFIG_ENV_OFFSET_REDUND + \ 183 CONFIG_ENV_SECT_SIZE) 184 #define TQMA6_FDT_SECT_SIZE (TQMA6_SPI_FLASH_SECTOR_SIZE) 185 186 #define TQMA6_FDT_SECTOR_START 0x0a /* 8 Sector u-boot, 2 Sector env */ 187 #define TQMA6_FDT_SECTOR_COUNT 0x01 188 189 #define TQMA6_KERNEL_SECTOR_START 0x10 190 #define TQMA6_KERNEL_SECTOR_COUNT 0x60 191 192 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \ 193 "mmcblkdev=0\0" \ 194 "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0" \ 195 "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \ 196 "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \ 197 "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \ 198 "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \ 199 "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \ 200 "update_uboot=if tftp ${uboot}; then " \ 201 "if itest ${filesize} > 0; then " \ 202 "setexpr blkc ${filesize} + " \ 203 __stringify(TQMA6_UBOOT_OFFSET) "; " \ 204 "setexpr size ${uboot_sectors} * " \ 205 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 206 "if itest ${blkc} <= ${size}; then " \ 207 "sf probe; " \ 208 "sf erase 0 ${size}; " \ 209 "sf write ${loadaddr} ${uboot_offset} " \ 210 "${filesize}; " \ 211 "fi; " \ 212 "fi; fi; " \ 213 "setenv filesize 0; setenv blkc; setenv size \0" \ 214 "update_kernel=run kernel_name; if tftp ${kernel}; then " \ 215 "if itest ${filesize} > 0; then " \ 216 "setexpr size ${kernel_sectors} * " \ 217 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 218 "setexpr offset ${kernel_start} * " \ 219 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 220 "if itest ${filesize} <= ${size}; then " \ 221 "sf probe; " \ 222 "sf erase ${offset} ${size}; " \ 223 "sf write ${loadaddr} ${offset} " \ 224 "${filesize}; " \ 225 "fi; " \ 226 "fi; fi; " \ 227 "setenv filesize 0; setenv size ; setenv offset\0" \ 228 "update_fdt=if tftp ${fdt_file}; then " \ 229 "if itest ${filesize} > 0; then " \ 230 "setexpr size ${fdt_sectors} * " \ 231 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 232 "setexpr offset ${fdt_start} * " \ 233 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 234 "if itest ${filesize} <= ${size}; then " \ 235 "sf probe; " \ 236 "sf erase ${offset} ${size}; " \ 237 "sf write ${loadaddr} ${offset} " \ 238 "${filesize}; " \ 239 "fi; " \ 240 "fi; fi; " \ 241 "setenv filesize 0; setenv size ; setenv offset\0" \ 242 "loadimage=sf probe; " \ 243 "setexpr size ${kernel_sectors} * " \ 244 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 245 "setexpr offset ${kernel_start} * " \ 246 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 247 "sf read ${loadaddr} ${offset} ${size}; " \ 248 "setenv size ; setenv offset\0" \ 249 "loadfdt=sf probe; " \ 250 "setexpr size ${fdt_sectors} * " \ 251 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 252 "setexpr offset ${fdt_start} * " \ 253 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 254 "sf read ${fdt_addr} ${offset} ${size}; " \ 255 "setenv size ; setenv offset\0" \ 256 257 #define CONFIG_BOOTCOMMAND \ 258 "sf probe; run mmcboot; run netboot; run panicboot" \ 259 260 #else 261 262 #error "need to define boot source" 263 264 #endif 265 266 /* 128 MiB offset as in ARM related docu for linux suggested */ 267 #define TQMA6_FDT_ADDRESS 0x18000000 268 269 /* set to a resonable value, changeable by user */ 270 #define TQMA6_CMA_SIZE 160M 271 272 #define CONFIG_EXTRA_ENV_SETTINGS \ 273 "board=tqma6\0" \ 274 "uimage=uImage\0" \ 275 "zimage=zImage\0" \ 276 "boot_type=bootz\0" \ 277 "kernel_name=if test \"${boot_type}\" != bootz; then " \ 278 "setenv kernel ${uimage}; " \ 279 "else setenv kernel ${zimage}; fi\0" \ 280 "uboot=u-boot.imx\0" \ 281 "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ 282 "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0" \ 283 "console=" CONSOLE_DEV "\0" \ 284 "cma_size="__stringify(TQMA6_CMA_SIZE)"\0" \ 285 "fdt_high=0xffffffff\0" \ 286 "initrd_high=0xffffffff\0" \ 287 "rootfsmode=ro\0" \ 288 "addcma=setenv bootargs ${bootargs} cma=${cma_size}\0" \ 289 "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \ 290 "addfb=setenv bootargs ${bootargs} " \ 291 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0" \ 292 "mmcpart=2\0" \ 293 "mmcblkdev=0\0" \ 294 "mmcargs=run addmmc addtty addfb addcma\0" \ 295 "addmmc=setenv bootargs ${bootargs} " \ 296 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} ${rootfsmode} " \ 297 "rootwait\0" \ 298 "mmcboot=echo Booting from mmc ...; " \ 299 "setenv bootargs; " \ 300 "run mmcargs; " \ 301 "run loadimage; " \ 302 "if run loadfdt; then " \ 303 "echo boot device tree kernel ...; " \ 304 "${boot_type} ${loadaddr} - ${fdt_addr}; " \ 305 "else " \ 306 "${boot_type}; " \ 307 "fi;\0" \ 308 "setenv bootargs \0" \ 309 "netdev=eth0\0" \ 310 "rootpath=/srv/nfs/tqma6\0" \ 311 "ipmode=static\0" \ 312 "netargs=run addnfs addip addtty addfb addcma\0" \ 313 "addnfs=setenv bootargs ${bootargs} " \ 314 "root=/dev/nfs rw " \ 315 "nfsroot=${serverip}:${rootpath},v3,tcp;\0" \ 316 "addip_static=setenv bootargs ${bootargs} " \ 317 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \ 318 "${hostname}:${netdev}:off\0" \ 319 "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0" \ 320 "addip=if test \"${ipmode}\" != static; then " \ 321 "run addip_dynamic; else run addip_static; fi\0" \ 322 "set_getcmd=if test \"${ipmode}\" != static; then " \ 323 "setenv getcmd dhcp; setenv autoload yes; " \ 324 "else setenv getcmd tftp; setenv autoload no; fi\0" \ 325 "netboot=echo Booting from net ...; " \ 326 "run kernel_name; " \ 327 "run set_getcmd; " \ 328 "setenv bootargs; " \ 329 "run netargs; " \ 330 "if ${getcmd} ${kernel}; then " \ 331 "if ${getcmd} ${fdt_addr} ${fdt_file}; then " \ 332 "${boot_type} ${loadaddr} - ${fdt_addr}; " \ 333 "fi; " \ 334 "fi; " \ 335 "echo ... failed\0" \ 336 "panicboot=echo No boot device !!! reset\0" \ 337 TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \ 338 339 /* Physical Memory Map */ 340 #define CONFIG_NR_DRAM_BANKS 1 341 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR 342 343 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 344 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 345 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 346 347 #define CONFIG_SYS_INIT_SP_OFFSET \ 348 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 349 #define CONFIG_SYS_INIT_SP_ADDR \ 350 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 351 352 /* 353 * All the defines above are for the TQMa6 SoM 354 * 355 * Now include the baseboard specific configuration 356 */ 357 #ifdef CONFIG_MBA6 358 #include "tqma6_mba6.h" 359 #elif CONFIG_WRU4 360 #include "tqma6_wru4.h" 361 #else 362 #error "No baseboard for the TQMa6 defined!" 363 #endif 364 365 /* Support at least the sensor on TQMa6 SOM */ 366 367 #endif /* __CONFIG_H */ 368