1 /* 2 * Copyright (C) 2013, 2014, 2017 Markus Niebel <Markus.Niebel@tq-group.com> 3 * 4 * Configuration settings for the TQ Systems TQMa6<Q,D,DL,S> module. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #include <linux/kconfig.h> 13 /* SPL */ 14 /* #if defined(CONFIG_SPL_BUILD) */ 15 /* common IMX6 SPL configuration */ 16 #include "imx6_spl.h" 17 18 /* #endif */ 19 20 /* place code in last 4 MiB of RAM */ 21 #if defined(CONFIG_TQMA6S) 22 #define CONFIG_SYS_TEXT_BASE 0x2fc00000 23 #elif defined(CONFIG_TQMA6Q) || defined(CONFIG_TQMA6DL) 24 #define CONFIG_SYS_TEXT_BASE 0x4fc00000 25 #endif 26 27 #include "mx6_common.h" 28 29 #if defined(CONFIG_TQMA6S) 30 #define PHYS_SDRAM_SIZE (512u * SZ_1M) 31 #elif defined(CONFIG_TQMA6DL) 32 #define PHYS_SDRAM_SIZE (SZ_1G) 33 #elif defined(CONFIG_TQMA6Q) 34 #define PHYS_SDRAM_SIZE (SZ_1G) 35 #endif 36 37 #define CONFIG_MXC_UART 38 39 /* SPI */ 40 #define CONFIG_MXC_SPI 41 42 /* SPI Flash */ 43 44 #define TQMA6_SPI_FLASH_SECTOR_SIZE SZ_64K 45 46 #define CONFIG_SF_DEFAULT_BUS 0 47 #define CONFIG_SF_DEFAULT_CS 0 48 #define CONFIG_SF_DEFAULT_SPEED 50000000 49 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) 50 51 /* I2C Configs */ 52 #define CONFIG_SYS_I2C 53 #define CONFIG_SYS_I2C_MXC 54 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 55 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 56 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 57 #define CONFIG_I2C_MULTI_BUS 58 #define CONFIG_SYS_I2C_SPEED 100000 59 60 /* I2C SYSMON (LM75) */ 61 #define CONFIG_DTT_LM75 62 #define CONFIG_DTT_MAX_TEMP 70 63 #define CONFIG_DTT_MIN_TEMP -30 64 #define CONFIG_DTT_HYSTERESIS 3 65 #define CONFIG_CMD_DTT 66 67 /* I2C EEPROM (M24C64) */ 68 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 69 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 70 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS 5 /* 32 Bytes */ 71 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS 20 72 #define CONFIG_CMD_EEPROM 73 74 #define CONFIG_POWER 75 #define CONFIG_POWER_I2C 76 #define CONFIG_POWER_PFUZE100 77 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 78 #define TQMA6_PFUZE100_I2C_BUS 2 79 80 /* MMC Configs */ 81 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 82 83 /* USB Configs */ 84 #define CONFIG_USB_HOST_ETHER 85 #define CONFIG_USB_ETHER_SMSC95XX 86 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 87 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 88 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ 89 90 #define CONFIG_FEC_MXC 91 #define IMX_FEC_BASE ENET_BASE_ADDR 92 #define CONFIG_PHYLIB 93 #define CONFIG_MII 94 95 #define CONFIG_ARP_TIMEOUT 200UL 96 97 #define CONFIG_ENV_SIZE (SZ_8K) 98 /* Size of malloc() pool */ 99 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * SZ_1M) 100 101 #if defined(CONFIG_TQMA6X_MMC_BOOT) 102 103 #define CONFIG_ENV_IS_IN_MMC 104 #define TQMA6_UBOOT_OFFSET SZ_1K 105 #define TQMA6_UBOOT_SECTOR_START 0x2 106 #define TQMA6_UBOOT_SECTOR_COUNT 0x7fe 107 108 #define CONFIG_ENV_OFFSET SZ_1M 109 #define CONFIG_SYS_MMC_ENV_DEV 0 110 111 #define TQMA6_FDT_OFFSET (2 * SZ_1M) 112 #define TQMA6_FDT_SECTOR_START 0x1000 113 #define TQMA6_FDT_SECTOR_COUNT 0x800 114 115 #define TQMA6_KERNEL_SECTOR_START 0x2000 116 #define TQMA6_KERNEL_SECTOR_COUNT 0x2000 117 118 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \ 119 "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0" \ 120 "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \ 121 "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \ 122 "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \ 123 "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \ 124 "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \ 125 "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \ 126 "loadimage=mmc dev ${mmcdev}; " \ 127 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0" \ 128 "loadfdt=mmc dev ${mmcdev}; " \ 129 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0" \ 130 "update_uboot=if tftp ${uboot}; then " \ 131 "if itest ${filesize} > 0; then " \ 132 "mmc dev ${mmcdev}; mmc rescan; " \ 133 "setexpr blkc ${filesize} + 0x1ff; " \ 134 "setexpr blkc ${blkc} / 0x200; " \ 135 "if itest ${blkc} <= ${uboot_size}; then " \ 136 "mmc write ${loadaddr} ${uboot_start} " \ 137 "${blkc}; " \ 138 "fi; " \ 139 "fi; fi; " \ 140 "setenv filesize; setenv blkc \0" \ 141 "update_kernel=run kernel_name; " \ 142 "if tftp ${kernel}; then " \ 143 "if itest ${filesize} > 0; then " \ 144 "mmc dev ${mmcdev}; mmc rescan; " \ 145 "setexpr blkc ${filesize} + 0x1ff; " \ 146 "setexpr blkc ${blkc} / 0x200; " \ 147 "if itest ${blkc} <= ${kernel_size}; then " \ 148 "mmc write ${loadaddr} " \ 149 "${kernel_start} ${blkc}; " \ 150 "fi; " \ 151 "fi; " \ 152 "fi; " \ 153 "setenv filesize; setenv blkc \0" \ 154 "update_fdt=if tftp ${fdt_file}; then " \ 155 "if itest ${filesize} > 0; then " \ 156 "mmc dev ${mmcdev}; mmc rescan; " \ 157 "setexpr blkc ${filesize} + 0x1ff; " \ 158 "setexpr blkc ${blkc} / 0x200; " \ 159 "if itest ${blkc} <= ${fdt_size}; then " \ 160 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \ 161 "fi; " \ 162 "fi; fi; " \ 163 "setenv filesize; setenv blkc \0" \ 164 165 #define CONFIG_BOOTCOMMAND \ 166 "run mmcboot; run netboot; run panicboot" 167 168 #elif defined(CONFIG_TQMA6X_SPI_BOOT) 169 170 #define TQMA6_UBOOT_OFFSET 0x400 171 #define TQMA6_UBOOT_SECTOR_START 0x0 172 /* max u-boot size: 512k */ 173 #define TQMA6_UBOOT_SECTOR_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE 174 #define TQMA6_UBOOT_SECTOR_COUNT 0x8 175 #define TQMA6_UBOOT_SIZE (TQMA6_UBOOT_SECTOR_SIZE * \ 176 TQMA6_UBOOT_SECTOR_COUNT) 177 178 #define CONFIG_ENV_IS_IN_SPI_FLASH 179 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 180 #define CONFIG_ENV_OFFSET (TQMA6_UBOOT_SIZE) 181 #define CONFIG_ENV_SECT_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE 182 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 183 CONFIG_ENV_SECT_SIZE) 184 185 #define CONFIG_ENV_SPI_BUS (CONFIG_SF_DEFAULT_BUS) 186 #define CONFIG_ENV_SPI_CS (CONFIG_SF_DEFAULT_CS) 187 #define CONFIG_ENV_SPI_MAX_HZ (CONFIG_SF_DEFAULT_SPEED) 188 #define CONFIG_ENV_SPI_MODE (CONFIG_SF_DEFAULT_MODE) 189 190 #define TQMA6_FDT_OFFSET (CONFIG_ENV_OFFSET_REDUND + \ 191 CONFIG_ENV_SECT_SIZE) 192 #define TQMA6_FDT_SECT_SIZE (TQMA6_SPI_FLASH_SECTOR_SIZE) 193 194 #define TQMA6_FDT_SECTOR_START 0x0a /* 8 Sector u-boot, 2 Sector env */ 195 #define TQMA6_FDT_SECTOR_COUNT 0x01 196 197 #define TQMA6_KERNEL_SECTOR_START 0x10 198 #define TQMA6_KERNEL_SECTOR_COUNT 0x60 199 200 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \ 201 "mmcblkdev=0\0" \ 202 "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0" \ 203 "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \ 204 "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \ 205 "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \ 206 "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \ 207 "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \ 208 "update_uboot=if tftp ${uboot}; then " \ 209 "if itest ${filesize} > 0; then " \ 210 "setexpr blkc ${filesize} + " \ 211 __stringify(TQMA6_UBOOT_OFFSET) "; " \ 212 "setexpr size ${uboot_sectors} * " \ 213 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 214 "if itest ${blkc} <= ${size}; then " \ 215 "sf probe; " \ 216 "sf erase 0 ${size}; " \ 217 "sf write ${loadaddr} ${uboot_offset} " \ 218 "${filesize}; " \ 219 "fi; " \ 220 "fi; fi; " \ 221 "setenv filesize 0; setenv blkc; setenv size \0" \ 222 "update_kernel=run kernel_name; if tftp ${kernel}; then " \ 223 "if itest ${filesize} > 0; then " \ 224 "setexpr size ${kernel_sectors} * " \ 225 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 226 "setexpr offset ${kernel_start} * " \ 227 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 228 "if itest ${filesize} <= ${size}; then " \ 229 "sf probe; " \ 230 "sf erase ${offset} ${size}; " \ 231 "sf write ${loadaddr} ${offset} " \ 232 "${filesize}; " \ 233 "fi; " \ 234 "fi; fi; " \ 235 "setenv filesize 0; setenv size ; setenv offset\0" \ 236 "update_fdt=if tftp ${fdt_file}; then " \ 237 "if itest ${filesize} > 0; then " \ 238 "setexpr size ${fdt_sectors} * " \ 239 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 240 "setexpr offset ${fdt_start} * " \ 241 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 242 "if itest ${filesize} <= ${size}; then " \ 243 "sf probe; " \ 244 "sf erase ${offset} ${size}; " \ 245 "sf write ${loadaddr} ${offset} " \ 246 "${filesize}; " \ 247 "fi; " \ 248 "fi; fi; " \ 249 "setenv filesize 0; setenv size ; setenv offset\0" \ 250 "loadimage=sf probe; " \ 251 "setexpr size ${kernel_sectors} * " \ 252 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 253 "setexpr offset ${kernel_start} * " \ 254 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 255 "sf read ${loadaddr} ${offset} ${size}; " \ 256 "setenv size ; setenv offset\0" \ 257 "loadfdt=sf probe; " \ 258 "setexpr size ${fdt_sectors} * " \ 259 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 260 "setexpr offset ${fdt_start} * " \ 261 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \ 262 "sf read ${fdt_addr} ${offset} ${size}; " \ 263 "setenv size ; setenv offset\0" \ 264 265 #define CONFIG_BOOTCOMMAND \ 266 "sf probe; run mmcboot; run netboot; run panicboot" \ 267 268 #else 269 270 #error "need to define boot source" 271 272 #endif 273 274 /* 128 MiB offset as in ARM related docu for linux suggested */ 275 #define TQMA6_FDT_ADDRESS 0x18000000 276 277 /* set to a resonable value, changeable by user */ 278 #define TQMA6_CMA_SIZE 160M 279 280 #define CONFIG_EXTRA_ENV_SETTINGS \ 281 "board=tqma6\0" \ 282 "uimage=uImage\0" \ 283 "zimage=zImage\0" \ 284 "boot_type=bootz\0" \ 285 "kernel_name=if test \"${boot_type}\" != bootz; then " \ 286 "setenv kernel ${uimage}; " \ 287 "else setenv kernel ${zimage}; fi\0" \ 288 "uboot=u-boot.imx\0" \ 289 "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ 290 "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0" \ 291 "console=" CONSOLE_DEV "\0" \ 292 "cma_size="__stringify(TQMA6_CMA_SIZE)"\0" \ 293 "fdt_high=0xffffffff\0" \ 294 "initrd_high=0xffffffff\0" \ 295 "rootfsmode=ro\0" \ 296 "addcma=setenv bootargs ${bootargs} cma=${cma_size}\0" \ 297 "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \ 298 "addfb=setenv bootargs ${bootargs} " \ 299 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0" \ 300 "mmcpart=2\0" \ 301 "mmcblkdev=0\0" \ 302 "mmcargs=run addmmc addtty addfb addcma\0" \ 303 "addmmc=setenv bootargs ${bootargs} " \ 304 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} ${rootfsmode} " \ 305 "rootwait\0" \ 306 "mmcboot=echo Booting from mmc ...; " \ 307 "setenv bootargs; " \ 308 "run mmcargs; " \ 309 "run loadimage; " \ 310 "if run loadfdt; then " \ 311 "echo boot device tree kernel ...; " \ 312 "${boot_type} ${loadaddr} - ${fdt_addr}; " \ 313 "else " \ 314 "${boot_type}; " \ 315 "fi;\0" \ 316 "setenv bootargs \0" \ 317 "netdev=eth0\0" \ 318 "rootpath=/srv/nfs/tqma6\0" \ 319 "ipmode=static\0" \ 320 "netargs=run addnfs addip addtty addfb addcma\0" \ 321 "addnfs=setenv bootargs ${bootargs} " \ 322 "root=/dev/nfs rw " \ 323 "nfsroot=${serverip}:${rootpath},v3,tcp;\0" \ 324 "addip_static=setenv bootargs ${bootargs} " \ 325 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \ 326 "${hostname}:${netdev}:off\0" \ 327 "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0" \ 328 "addip=if test \"${ipmode}\" != static; then " \ 329 "run addip_dynamic; else run addip_static; fi\0" \ 330 "set_getcmd=if test \"${ipmode}\" != static; then " \ 331 "setenv getcmd dhcp; setenv autoload yes; " \ 332 "else setenv getcmd tftp; setenv autoload no; fi\0" \ 333 "netboot=echo Booting from net ...; " \ 334 "run kernel_name; " \ 335 "run set_getcmd; " \ 336 "setenv bootargs; " \ 337 "run netargs; " \ 338 "if ${getcmd} ${kernel}; then " \ 339 "if ${getcmd} ${fdt_addr} ${fdt_file}; then " \ 340 "${boot_type} ${loadaddr} - ${fdt_addr}; " \ 341 "fi; " \ 342 "fi; " \ 343 "echo ... failed\0" \ 344 "panicboot=echo No boot device !!! reset\0" \ 345 TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \ 346 347 /* Physical Memory Map */ 348 #define CONFIG_NR_DRAM_BANKS 1 349 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR 350 351 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 352 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 353 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 354 355 #define CONFIG_SYS_INIT_SP_OFFSET \ 356 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 357 #define CONFIG_SYS_INIT_SP_ADDR \ 358 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 359 360 /* 361 * All the defines above are for the TQMa6 SoM 362 * 363 * Now include the baseboard specific configuration 364 */ 365 #ifdef CONFIG_MBA6 366 #include "tqma6_mba6.h" 367 #elif CONFIG_WRU4 368 #include "tqma6_wru4.h" 369 #else 370 #error "No baseboard for the TQMa6 defined!" 371 #endif 372 373 /* Support at least the sensor on TQMa6 SOM */ 374 #if !defined(CONFIG_DTT_SENSORS) 375 #define CONFIG_DTT_SENSORS { 0 } 376 #endif 377 378 #endif /* __CONFIG_H */ 379