1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2014 Topic Embedded Products 4 * 5 * Configuration for Zynq Evaluation and Development Board - Miami 6 * See zynq-common.h for Zynq common configs 7 */ 8 9 #ifndef __CONFIG_TOPIC_MIAMI_H 10 #define __CONFIG_TOPIC_MIAMI_H 11 12 13 /* Speed up boot time by ignoring the environment which we never used */ 14 15 #include "zynq-common.h" 16 17 /* Fixup settings */ 18 #undef CONFIG_ENV_SIZE 19 #define CONFIG_ENV_SIZE 0x8000 20 #undef CONFIG_ENV_OFFSET 21 #define CONFIG_ENV_OFFSET 0x80000 22 23 /* SPL settings */ 24 #undef CONFIG_SPL_ETH_SUPPORT 25 #undef CONFIG_SYS_SPI_U_BOOT_OFFS 26 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 27 #undef CONFIG_SPL_MAX_FOOTPRINT 28 #define CONFIG_SPL_MAX_FOOTPRINT CONFIG_SYS_SPI_U_BOOT_OFFS 29 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 30 31 /* sspi command isn't useful */ 32 #undef CONFIG_CMD_SPI 33 34 /* No useful gpio */ 35 #undef CONFIG_ZYNQ_GPIO 36 #undef CONFIG_CMD_GPIO 37 38 /* No falcon support */ 39 #undef CONFIG_SPL_OS_BOOT 40 #undef CONFIG_SPL_FPGA_SUPPORT 41 42 /* FPGA commands that we don't use */ 43 44 /* Extras */ 45 #undef CONFIG_SYS_MEMTEST_START 46 #define CONFIG_SYS_MEMTEST_START 0 47 #undef CONFIG_SYS_MEMTEST_END 48 #define CONFIG_SYS_MEMTEST_END 0x18000000 49 50 /* Faster flash, ours may run at 108 MHz */ 51 #undef CONFIG_SF_DEFAULT_SPEED 52 #define CONFIG_SF_DEFAULT_SPEED 108000000 53 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 54 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 55 #undef CONFIG_SPI_FLASH_WINBOND 56 #undef CONFIG_SPI_FLASH_ISSI 57 58 /* Setup proper boot sequences for Miami boards */ 59 60 #if defined(CONFIG_USB) 61 # define EXTRA_ENV_USB \ 62 "usbreset=i2c dev 1 && i2c mw 41 1 ff && i2c mw 41 3 fe && "\ 63 "i2c mw 41 1 fe && i2c mw 41 1 ff\0" \ 64 "usbboot=run usbreset && if usb start; then " \ 65 "echo Booting from USB... && " \ 66 "if load usb 0 0x1900000 ${bootscript}; then "\ 67 "source 0x1900000; fi; " \ 68 "load usb 0 ${kernel_addr} ${kernel_image} && " \ 69 "load usb 0 ${devicetree_addr} ${devicetree_image} && " \ 70 "load usb 0 ${ramdisk_load_address} ${ramdisk_image} && " \ 71 "bootm ${kernel_addr} ${ramdisk_load_address} "\ 72 "${devicetree_addr}; " \ 73 "fi\0" 74 /* Note that addresses here should match the addresses in the env */ 75 # undef DFU_ALT_INFO 76 # define DFU_ALT_INFO \ 77 "dfu_alt_info=" \ 78 "uImage ram 0x2080000 0x500000;" \ 79 "devicetree.dtb ram 0x2000000 0x20000;" \ 80 "uramdisk.image.gz ram 0x4000000 0x10000000\0" \ 81 "dfu_ram=run usbreset && dfu 0 ram 0\0" \ 82 "thor_ram=run usbreset && thordown 0 ram 0\0" 83 #else 84 # define EXTRA_ENV_USB 85 #endif 86 87 #undef CONFIG_PREBOOT 88 89 #undef CONFIG_EXTRA_ENV_SETTINGS 90 #define CONFIG_EXTRA_ENV_SETTINGS \ 91 "kernel_image=uImage\0" \ 92 "kernel_addr=0x2080000\0" \ 93 "ramdisk_image=uramdisk.image.gz\0" \ 94 "ramdisk_load_address=0x4000000\0" \ 95 "devicetree_image=devicetree.dtb\0" \ 96 "devicetree_addr=0x2000000\0" \ 97 "bitstream_image=fpga.bin\0" \ 98 "bootscript=autorun.scr\0" \ 99 "loadbit_addr=0x100000\0" \ 100 "loadbootenv_addr=0x2000000\0" \ 101 "kernel_size=0x440000\0" \ 102 "devicetree_size=0x10000\0" \ 103 "boot_size=0xF00000\0" \ 104 "fdt_high=0x20000000\0" \ 105 "initrd_high=0x20000000\0" \ 106 "mmc_loadbit=echo Loading bitstream from SD/MMC/eMMC to RAM.. && " \ 107 "mmcinfo && " \ 108 "load mmc 0 ${loadbit_addr} ${bitstream_image} && " \ 109 "fpga load 0 ${loadbit_addr} ${filesize}\0" \ 110 "qspiboot=echo Booting from QSPI flash... && " \ 111 "sf probe && " \ 112 "sf read ${devicetree_addr} 0xA0000 ${devicetree_size} && " \ 113 "sf read ${kernel_addr} 0xC0000 ${kernel_size} && " \ 114 "bootm ${kernel_addr} - ${devicetree_addr}\0" \ 115 "sdboot=if mmcinfo; then " \ 116 "setenv bootargs console=ttyPS0,115200 " \ 117 "root=/dev/mmcblk0p2 rw rootfstype=ext4 " \ 118 "rootwait quiet ; " \ 119 "load mmc 0 ${kernel_addr} ${kernel_image}&& " \ 120 "load mmc 0 ${devicetree_addr} ${devicetree_image}&& " \ 121 "bootm ${kernel_addr} - ${devicetree_addr}; " \ 122 "fi\0" \ 123 EXTRA_ENV_USB \ 124 DFU_ALT_INFO 125 126 #undef CONFIG_BOOTCOMMAND 127 #define CONFIG_BOOTCOMMAND "if mmcinfo; then " \ 128 "if fatload mmc 0 0x1900000 ${bootscript}; then source 0x1900000; " \ 129 "fi; fi; run $modeboot" 130 #undef CONFIG_DISPLAY_BOARDINFO 131 132 #endif /* __CONFIG_TOPIC_MIAMI_H */ 133