1 /* 2 * Common configuration header file for all Keystone II EVM platforms 3 * 4 * (C) Copyright 2012-2014 5 * Texas Instruments Incorporated, <www.ti.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_KS2_EVM_H 11 #define __CONFIG_KS2_EVM_H 12 13 #define CONFIG_SOC_KEYSTONE 14 15 /* U-Boot Build Configuration */ 16 #define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 2nd stage loader */ 17 #define CONFIG_BOARD_EARLY_INIT_F 18 #define CONFIG_DISPLAY_CPUINFO 19 20 /* SoC Configuration */ 21 #define CONFIG_ARCH_CPU_INIT 22 #define CONFIG_SYS_ARCH_TIMER 23 #define CONFIG_SYS_TEXT_BASE 0x0c000000 24 #define CONFIG_SPL_TARGET "u-boot-spi.gph" 25 #define CONFIG_SYS_DCACHE_OFF 26 27 /* Memory Configuration */ 28 #define CONFIG_NR_DRAM_BANKS 2 29 #define CONFIG_SYS_LPAE_SDRAM_BASE 0x800000000 30 #define CONFIG_MAX_RAM_BANK_SIZE (2 << 30) /* 2GB */ 31 #define CONFIG_STACKSIZE (512 << 10) /* 512 KiB */ 32 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE - \ 33 GENERATED_GBL_DATA_SIZE) 34 35 /* SPL SPI Loader Configuration */ 36 #define CONFIG_SPL_PAD_TO 65536 37 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_PAD_TO - 8) 38 #define CONFIG_SPL_BSS_START_ADDR (CONFIG_SPL_TEXT_BASE + \ 39 CONFIG_SPL_MAX_SIZE) 40 #define CONFIG_SPL_BSS_MAX_SIZE (32 * 1024) 41 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ 42 CONFIG_SPL_BSS_MAX_SIZE) 43 #define CONFIG_SYS_SPL_MALLOC_SIZE (32 * 1024) 44 #define CONFIG_SPL_STACK_SIZE (8 * 1024) 45 #define CONFIG_SPL_STACK (CONFIG_SYS_SPL_MALLOC_START + \ 46 CONFIG_SYS_SPL_MALLOC_SIZE + \ 47 CONFIG_SPL_STACK_SIZE - 4) 48 #define CONFIG_SPL_SPI_FLASH_SUPPORT 49 #define CONFIG_SPL_SPI_SUPPORT 50 #define CONFIG_SPL_SPI_LOAD 51 #define CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_SPL_PAD_TO 52 53 /* UART Configuration */ 54 #define CONFIG_SYS_NS16550 55 #define CONFIG_SYS_NS16550_SERIAL 56 #define CONFIG_SYS_NS16550_MEM32 57 #define CONFIG_SYS_NS16550_REG_SIZE -4 58 #define CONFIG_SYS_NS16550_COM1 KS2_UART0_BASE 59 #define CONFIG_SYS_NS16550_COM2 KS2_UART1_BASE 60 #define CONFIG_SYS_NS16550_CLK clk_get_rate(KS2_CLK1_6) 61 #define CONFIG_CONS_INDEX 1 62 63 /* SPI Configuration */ 64 #define CONFIG_SPI_FLASH_STMICRO 65 #define CONFIG_DAVINCI_SPI 66 #define CONFIG_SYS_SPI_CLK clk_get_rate(KS2_CLK1_6) 67 #define CONFIG_SF_DEFAULT_SPEED 30000000 68 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 69 #define CONFIG_SYS_SPI0 70 #define CONFIG_SYS_SPI_BASE KS2_SPI0_BASE 71 #define CONFIG_SYS_SPI0_NUM_CS 4 72 #define CONFIG_SYS_SPI1 73 #define CONFIG_SYS_SPI1_BASE KS2_SPI1_BASE 74 #define CONFIG_SYS_SPI1_NUM_CS 4 75 #define CONFIG_SYS_SPI2 76 #define CONFIG_SYS_SPI2_BASE KS2_SPI2_BASE 77 #define CONFIG_SYS_SPI2_NUM_CS 4 78 79 /* Network Configuration */ 80 #define CONFIG_PHYLIB 81 #define CONFIG_PHY_MARVELL 82 #define CONFIG_MII 83 #define CONFIG_BOOTP_DEFAULT 84 #define CONFIG_BOOTP_DNS 85 #define CONFIG_BOOTP_DNS2 86 #define CONFIG_BOOTP_SEND_HOSTNAME 87 #define CONFIG_NET_RETRY_COUNT 32 88 #define CONFIG_SYS_SGMII_REFCLK_MHZ 312 89 #define CONFIG_SYS_SGMII_LINERATE_MHZ 1250 90 #define CONFIG_SYS_SGMII_RATESCALE 2 91 92 /* Keyston Navigator Configuration */ 93 #define CONFIG_TI_KSNAV 94 #define CONFIG_KSNAV_QM_BASE_ADDRESS KS2_QM_BASE_ADDRESS 95 #define CONFIG_KSNAV_QM_CONF_BASE KS2_QM_CONF_BASE 96 #define CONFIG_KSNAV_QM_DESC_SETUP_BASE KS2_QM_DESC_SETUP_BASE 97 #define CONFIG_KSNAV_QM_STATUS_RAM_BASE KS2_QM_STATUS_RAM_BASE 98 #define CONFIG_KSNAV_QM_INTD_CONF_BASE KS2_QM_INTD_CONF_BASE 99 #define CONFIG_KSNAV_QM_PDSP1_CMD_BASE KS2_QM_PDSP1_CMD_BASE 100 #define CONFIG_KSNAV_QM_PDSP1_CTRL_BASE KS2_QM_PDSP1_CTRL_BASE 101 #define CONFIG_KSNAV_QM_PDSP1_IRAM_BASE KS2_QM_PDSP1_IRAM_BASE 102 #define CONFIG_KSNAV_QM_MANAGER_QUEUES_BASE KS2_QM_MANAGER_QUEUES_BASE 103 #define CONFIG_KSNAV_QM_MANAGER_Q_PROXY_BASE KS2_QM_MANAGER_Q_PROXY_BASE 104 #define CONFIG_KSNAV_QM_QUEUE_STATUS_BASE KS2_QM_QUEUE_STATUS_BASE 105 #define CONFIG_KSNAV_QM_LINK_RAM_BASE KS2_QM_LINK_RAM_BASE 106 #define CONFIG_KSNAV_QM_REGION_NUM KS2_QM_REGION_NUM 107 #define CONFIG_KSNAV_QM_QPOOL_NUM KS2_QM_QPOOL_NUM 108 109 /* NETCP pktdma */ 110 #define CONFIG_KSNAV_PKTDMA_NETCP 111 #define CONFIG_KSNAV_NETCP_PDMA_CTRL_BASE KS2_NETCP_PDMA_CTRL_BASE 112 #define CONFIG_KSNAV_NETCP_PDMA_TX_BASE KS2_NETCP_PDMA_TX_BASE 113 #define CONFIG_KSNAV_NETCP_PDMA_TX_CH_NUM KS2_NETCP_PDMA_TX_CH_NUM 114 #define CONFIG_KSNAV_NETCP_PDMA_RX_BASE KS2_NETCP_PDMA_RX_BASE 115 #define CONFIG_KSNAV_NETCP_PDMA_RX_CH_NUM KS2_NETCP_PDMA_RX_CH_NUM 116 #define CONFIG_KSNAV_NETCP_PDMA_SCHED_BASE KS2_NETCP_PDMA_SCHED_BASE 117 #define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_BASE KS2_NETCP_PDMA_RX_FLOW_BASE 118 #define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_NUM KS2_NETCP_PDMA_RX_FLOW_NUM 119 #define CONFIG_KSNAV_NETCP_PDMA_RX_FREE_QUEUE KS2_NETCP_PDMA_RX_FREE_QUEUE 120 #define CONFIG_KSNAV_NETCP_PDMA_RX_RCV_QUEUE KS2_NETCP_PDMA_RX_RCV_QUEUE 121 #define CONFIG_KSNAV_NETCP_PDMA_TX_SND_QUEUE KS2_NETCP_PDMA_TX_SND_QUEUE 122 123 /* Keystone net */ 124 #define CONFIG_DRIVER_TI_KEYSTONE_NET 125 #define CONFIG_KSNET_MAC_ID_BASE KS2_MAC_ID_BASE_ADDR 126 #define CONFIG_KSNET_NETCP_BASE KS2_NETCP_BASE 127 #define CONFIG_KSNET_SERDES_SGMII_BASE KS2_SGMII_SERDES_BASE 128 #define CONFIG_KSNET_SERDES_SGMII2_BASE KS2_SGMII_SERDES2_BASE 129 #define CONFIG_KSNET_SERDES_LANES_PER_SGMII KS2_LANES_PER_SGMII_SERDES 130 131 /* SerDes */ 132 #define CONFIG_TI_KEYSTONE_SERDES 133 134 /* AEMIF */ 135 #define CONFIG_TI_AEMIF 136 #define CONFIG_AEMIF_CNTRL_BASE KS2_AEMIF_CNTRL_BASE 137 138 /* I2C Configuration */ 139 #define CONFIG_SYS_I2C_DAVINCI 140 #define CONFIG_SYS_DAVINCI_I2C_SPEED 100000 141 #define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */ 142 #define CONFIG_SYS_DAVINCI_I2C_SPEED1 100000 143 #define CONFIG_SYS_DAVINCI_I2C_SLAVE1 0x10 /* SMBus host address */ 144 #define CONFIG_SYS_DAVINCI_I2C_SPEED2 100000 145 #define CONFIG_SYS_DAVINCI_I2C_SLAVE2 0x10 /* SMBus host address */ 146 #define I2C_BUS_MAX 3 147 148 /* EEPROM definitions */ 149 #define CONFIG_SYS_I2C_MULTI_EEPROMS 150 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 151 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 152 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 153 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 154 #define CONFIG_ENV_EEPROM_IS_ON_I2C 155 156 /* NAND Configuration */ 157 #define CONFIG_NAND_DAVINCI 158 #define CONFIG_KEYSTONE_RBL_NAND 159 #define CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE CONFIG_ENV_OFFSET 160 #define CONFIG_SYS_NAND_MASK_CLE 0x4000 161 #define CONFIG_SYS_NAND_MASK_ALE 0x2000 162 #define CONFIG_SYS_NAND_CS 2 163 #define CONFIG_SYS_NAND_USE_FLASH_BBT 164 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST 165 166 #define CONFIG_SYS_NAND_LARGEPAGE 167 #define CONFIG_SYS_NAND_BASE_LIST { 0x30000000, } 168 #define CONFIG_SYS_MAX_NAND_DEVICE 1 169 #define CONFIG_SYS_NAND_MAX_CHIPS 1 170 #define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE 171 #define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */ 172 #define CONFIG_ENV_IS_IN_NAND 173 #define CONFIG_ENV_OFFSET 0x100000 174 #define CONFIG_MTD_PARTITIONS 175 #define CONFIG_RBTREE 176 #define CONFIG_LZO 177 #define MTDIDS_DEFAULT "nand0=davinci_nand.0" 178 #define MTDPARTS_DEFAULT "mtdparts=davinci_nand.0:" \ 179 "1024k(bootloader)ro,512k(params)ro," \ 180 "-(ubifs)" 181 182 /* USB Configuration */ 183 #define CONFIG_USB_XHCI 184 #define CONFIG_USB_XHCI_DWC3 185 #define CONFIG_USB_XHCI_KEYSTONE 186 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 187 #define CONFIG_EFI_PARTITION 188 #define CONFIG_FS_FAT 189 #define CONFIG_SYS_CACHELINE_SIZE 64 190 #define CONFIG_USB_SS_BASE KS2_USB_SS_BASE 191 #define CONFIG_USB_HOST_XHCI_BASE KS2_USB_HOST_XHCI_BASE 192 #define CONFIG_DEV_USB_PHY_BASE KS2_DEV_USB_PHY_BASE 193 #define CONFIG_USB_PHY_CFG_BASE KS2_USB_PHY_CFG_BASE 194 195 /* U-Boot command configuration */ 196 #define CONFIG_CMD_DHCP 197 #define CONFIG_CMD_PING 198 #define CONFIG_CMD_SAVES 199 #define CONFIG_CMD_NAND 200 #define CONFIG_CMD_UBI 201 #define CONFIG_CMD_UBIFS 202 #define CONFIG_CMD_SF 203 #define CONFIG_CMD_EEPROM 204 #define CONFIG_CMD_USB 205 206 /* U-Boot general configuration */ 207 #define CONFIG_MISC_INIT_R 208 #define CONFIG_CRC32_VERIFY 209 #define CONFIG_MX_CYCLIC 210 #define CONFIG_TIMESTAMP 211 212 /* EDMA3 */ 213 #define CONFIG_TI_EDMA3 214 215 #define CONFIG_EXTRA_ENV_SETTINGS \ 216 DEFAULT_LINUX_BOOT_ENV \ 217 CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS \ 218 "boot=ubi\0" \ 219 "tftp_root=/\0" \ 220 "nfs_root=/export\0" \ 221 "mem_lpae=1\0" \ 222 "mem_reserve=512M\0" \ 223 "addr_ubi=0x82000000\0" \ 224 "addr_secdb_key=0xc000000\0" \ 225 "name_kern=zImage\0" \ 226 "run_mon=mon_install ${addr_mon}\0" \ 227 "run_kern=bootz ${loadaddr} - ${fdtaddr}\0" \ 228 "init_net=run args_all args_net\0" \ 229 "init_ubi=run args_all args_ubi; " \ 230 "ubi part ubifs; ubifsmount ubi:boot;" \ 231 "ubifsload ${addr_secdb_key} securedb.key.bin;\0" \ 232 "get_fdt_net=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0" \ 233 "get_fdt_ubi=ubifsload ${fdtaddr} ${name_fdt}\0" \ 234 "get_kern_net=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0" \ 235 "get_kern_ubi=ubifsload ${loadaddr} ${name_kern}\0" \ 236 "get_mon_net=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0" \ 237 "get_mon_ubi=ubifsload ${addr_mon} ${name_mon}\0" \ 238 "get_uboot_net=dhcp ${loadaddr} ${tftp_root}/${name_uboot}\0" \ 239 "burn_uboot_spi=sf probe; sf erase 0 0x100000; " \ 240 "sf write ${loadaddr} 0 ${filesize}\0" \ 241 "burn_uboot_nand=nand erase 0 0x100000; " \ 242 "nand write ${loadaddr} 0 ${filesize}\0" \ 243 "args_all=setenv bootargs console=ttyS0,115200n8 rootwait=1\0" \ 244 "args_net=setenv bootargs ${bootargs} rootfstype=nfs " \ 245 "root=/dev/nfs rw nfsroot=${serverip}:${nfs_root}," \ 246 "${nfs_options} ip=dhcp\0" \ 247 "nfs_options=v3,tcp,rsize=4096,wsize=4096\0" \ 248 "get_fdt_ramfs=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0" \ 249 "get_kern_ramfs=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0" \ 250 "get_mon_ramfs=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0" \ 251 "get_fs_ramfs=dhcp ${rdaddr} ${tftp_root}/${name_fs}\0" \ 252 "get_ubi_net=dhcp ${addr_ubi} ${tftp_root}/${name_ubi}\0" \ 253 "burn_ubi=nand erase.part ubifs; " \ 254 "nand write ${addr_ubi} ubifs ${filesize}\0" \ 255 "init_ramfs=run args_all args_ramfs get_fs_ramfs\0" \ 256 "args_ramfs=setenv bootargs ${bootargs} " \ 257 "rdinit=/sbin/init rw root=/dev/ram0 " \ 258 "initrd=0x808080000,80M\0" \ 259 "no_post=1\0" \ 260 "mtdparts=mtdparts=davinci_nand.0:" \ 261 "1024k(bootloader)ro,512k(params)ro,-(ubifs)\0" 262 263 #define CONFIG_BOOTCOMMAND \ 264 "run init_${boot} get_fdt_${boot} get_mon_${boot} " \ 265 "get_kern_${boot} run_mon run_kern" 266 267 #define CONFIG_BOOTARGS \ 268 269 /* Linux interfacing */ 270 #define CONFIG_OF_BOARD_SETUP 271 272 /* Now for the remaining common defines */ 273 #include <configs/ti_armv7_common.h> 274 275 /* We wont be loading up OS from SPL for now.. */ 276 #undef CONFIG_SPL_OS_BOOT 277 278 /* We do not have MMC support.. yet.. */ 279 #undef CONFIG_SPL_LIBDISK_SUPPORT 280 #undef CONFIG_SPL_MMC_SUPPORT 281 #undef CONFIG_SPL_FAT_SUPPORT 282 #undef CONFIG_SPL_EXT_SUPPORT 283 #undef CONFIG_MMC 284 #undef CONFIG_GENERIC_MMC 285 #undef CONFIG_CMD_MMC 286 287 /* And no support for GPIO, yet.. */ 288 #undef CONFIG_SPL_GPIO_SUPPORT 289 #undef CONFIG_CMD_GPIO 290 291 /* we may include files below only after all above definitions */ 292 #include <asm/arch/hardware.h> 293 #include <asm/arch/clock.h> 294 #define CONFIG_SYS_HZ_CLOCK clk_get_rate(KS2_CLK1_6) 295 296 #endif /* __CONFIG_KS2_EVM_H */ 297