1 /*
2  * Common configuration header file for all Keystone II EVM platforms
3  *
4  * (C) Copyright 2012-2014
5  *     Texas Instruments Incorporated, <www.ti.com>
6  *
7  * SPDX-License-Identifier:     GPL-2.0+
8  */
9 
10 #ifndef __CONFIG_KS2_EVM_H
11 #define __CONFIG_KS2_EVM_H
12 
13 #define CONFIG_SOC_KEYSTONE
14 
15 /* U-Boot Build Configuration */
16 #define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is a 2nd stage loader */
17 
18 /* SoC Configuration */
19 #define CONFIG_ARCH_CPU_INIT
20 #define CONFIG_SYS_ARCH_TIMER
21 #ifndef CONFIG_SYS_TEXT_BASE
22 #define CONFIG_SYS_TEXT_BASE		0x0c000000
23 #endif
24 #define CONFIG_SPL_TARGET		"u-boot-spi.gph"
25 #define CONFIG_SYS_DCACHE_OFF
26 
27 /* Memory Configuration */
28 #define CONFIG_NR_DRAM_BANKS		2
29 #define CONFIG_SYS_LPAE_SDRAM_BASE	0x800000000
30 #define CONFIG_MAX_RAM_BANK_SIZE	(2 << 30)       /* 2GB */
31 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SPL_TEXT_BASE - \
32 					GENERATED_GBL_DATA_SIZE)
33 
34 #ifdef CONFIG_SYS_MALLOC_F_LEN
35 #define SPL_MALLOC_F_SIZE	CONFIG_SYS_MALLOC_F_LEN
36 #else
37 #define SPL_MALLOC_F_SIZE	0
38 #endif
39 
40 /* SPL SPI Loader Configuration */
41 #define CONFIG_SPL_PAD_TO		65536
42 #define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_PAD_TO - 8)
43 #define CONFIG_SPL_BSS_START_ADDR	(CONFIG_SPL_TEXT_BASE + \
44 					CONFIG_SPL_MAX_SIZE)
45 #define CONFIG_SPL_BSS_MAX_SIZE		(32 * 1024)
46 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
47 					CONFIG_SPL_BSS_MAX_SIZE)
48 #define CONFIG_SYS_SPL_MALLOC_SIZE	(32 * 1024)
49 #define KEYSTONE_SPL_STACK_SIZE		(8 * 1024)
50 #define CONFIG_SPL_STACK		(CONFIG_SYS_SPL_MALLOC_START + \
51 					CONFIG_SYS_SPL_MALLOC_SIZE + \
52 					SPL_MALLOC_F_SIZE + \
53 					KEYSTONE_SPL_STACK_SIZE - 4)
54 #define CONFIG_SPL_SPI_LOAD
55 #define CONFIG_SYS_SPI_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
56 
57 /* SRAM scratch space entries  */
58 #define SRAM_SCRATCH_SPACE_ADDR	CONFIG_SPL_STACK + 0x8
59 
60 #define TI_SRAM_SCRATCH_BOARD_EEPROM_START	(SRAM_SCRATCH_SPACE_ADDR)
61 #define TI_SRAM_SCRATCH_BOARD_EEPROM_END	(SRAM_SCRATCH_SPACE_ADDR + 0x200)
62 #define KEYSTONE_SRAM_SCRATCH_SPACE_END		(TI_SRAM_SCRATCH_BOARD_EEPROM_END)
63 
64 /* UART Configuration */
65 #define CONFIG_SYS_NS16550_MEM32
66 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_DM_SERIAL)
67 #define CONFIG_SYS_NS16550_SERIAL
68 #define CONFIG_SYS_NS16550_REG_SIZE	-4
69 #endif
70 #define CONFIG_SYS_NS16550_COM1		KS2_UART0_BASE
71 #define CONFIG_SYS_NS16550_COM2		KS2_UART1_BASE
72 #define CONFIG_CONS_INDEX		1
73 
74 #ifndef CONFIG_SOC_K2G
75 #define CONFIG_SYS_NS16550_CLK		ks_clk_get_rate(KS2_CLK1_6)
76 #else
77 #define CONFIG_SYS_NS16550_CLK		ks_clk_get_rate(uart_pll_clk) / 2
78 #endif
79 
80 /* SPI Configuration */
81 #define CONFIG_SYS_SPI_CLK		ks_clk_get_rate(KS2_CLK1_6)
82 #define CONFIG_SF_DEFAULT_SPEED		30000000
83 #define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
84 #define CONFIG_SYS_SPI0
85 #define CONFIG_SYS_SPI_BASE		KS2_SPI0_BASE
86 #define CONFIG_SYS_SPI0_NUM_CS		4
87 #define CONFIG_SYS_SPI1
88 #define CONFIG_SYS_SPI1_BASE		KS2_SPI1_BASE
89 #define CONFIG_SYS_SPI1_NUM_CS		4
90 #define CONFIG_SYS_SPI2
91 #define CONFIG_SYS_SPI2_BASE		KS2_SPI2_BASE
92 #define CONFIG_SYS_SPI2_NUM_CS		4
93 #ifdef CONFIG_SPL_BUILD
94 #undef CONFIG_DM_SPI
95 #undef CONFIG_DM_SPI_FLASH
96 #endif
97 
98 /* Network Configuration */
99 #define CONFIG_PHY_MARVELL
100 #define CONFIG_MII
101 #define CONFIG_BOOTP_DEFAULT
102 #define CONFIG_BOOTP_DNS
103 #define CONFIG_BOOTP_DNS2
104 #define CONFIG_BOOTP_SEND_HOSTNAME
105 #define CONFIG_NET_RETRY_COUNT		32
106 #define CONFIG_SYS_SGMII_REFCLK_MHZ	312
107 #define CONFIG_SYS_SGMII_LINERATE_MHZ	1250
108 #define CONFIG_SYS_SGMII_RATESCALE	2
109 
110 /* Keyston Navigator Configuration */
111 #define CONFIG_TI_KSNAV
112 #define CONFIG_KSNAV_QM_BASE_ADDRESS		KS2_QM_BASE_ADDRESS
113 #define CONFIG_KSNAV_QM_CONF_BASE		KS2_QM_CONF_BASE
114 #define CONFIG_KSNAV_QM_DESC_SETUP_BASE		KS2_QM_DESC_SETUP_BASE
115 #define CONFIG_KSNAV_QM_STATUS_RAM_BASE		KS2_QM_STATUS_RAM_BASE
116 #define CONFIG_KSNAV_QM_INTD_CONF_BASE		KS2_QM_INTD_CONF_BASE
117 #define CONFIG_KSNAV_QM_PDSP1_CMD_BASE		KS2_QM_PDSP1_CMD_BASE
118 #define CONFIG_KSNAV_QM_PDSP1_CTRL_BASE		KS2_QM_PDSP1_CTRL_BASE
119 #define CONFIG_KSNAV_QM_PDSP1_IRAM_BASE		KS2_QM_PDSP1_IRAM_BASE
120 #define CONFIG_KSNAV_QM_MANAGER_QUEUES_BASE	KS2_QM_MANAGER_QUEUES_BASE
121 #define CONFIG_KSNAV_QM_MANAGER_Q_PROXY_BASE	KS2_QM_MANAGER_Q_PROXY_BASE
122 #define CONFIG_KSNAV_QM_QUEUE_STATUS_BASE	KS2_QM_QUEUE_STATUS_BASE
123 #define CONFIG_KSNAV_QM_LINK_RAM_BASE		KS2_QM_LINK_RAM_BASE
124 #define CONFIG_KSNAV_QM_REGION_NUM		KS2_QM_REGION_NUM
125 #define CONFIG_KSNAV_QM_QPOOL_NUM		KS2_QM_QPOOL_NUM
126 
127 /* NETCP pktdma */
128 #define CONFIG_KSNAV_PKTDMA_NETCP
129 #define CONFIG_KSNAV_NETCP_PDMA_CTRL_BASE	KS2_NETCP_PDMA_CTRL_BASE
130 #define CONFIG_KSNAV_NETCP_PDMA_TX_BASE		KS2_NETCP_PDMA_TX_BASE
131 #define CONFIG_KSNAV_NETCP_PDMA_TX_CH_NUM	KS2_NETCP_PDMA_TX_CH_NUM
132 #define CONFIG_KSNAV_NETCP_PDMA_RX_BASE		KS2_NETCP_PDMA_RX_BASE
133 #define CONFIG_KSNAV_NETCP_PDMA_RX_CH_NUM	KS2_NETCP_PDMA_RX_CH_NUM
134 #define CONFIG_KSNAV_NETCP_PDMA_SCHED_BASE	KS2_NETCP_PDMA_SCHED_BASE
135 #define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_BASE	KS2_NETCP_PDMA_RX_FLOW_BASE
136 #define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_NUM	KS2_NETCP_PDMA_RX_FLOW_NUM
137 #define CONFIG_KSNAV_NETCP_PDMA_RX_FREE_QUEUE	KS2_NETCP_PDMA_RX_FREE_QUEUE
138 #define CONFIG_KSNAV_NETCP_PDMA_RX_RCV_QUEUE	KS2_NETCP_PDMA_RX_RCV_QUEUE
139 #define CONFIG_KSNAV_NETCP_PDMA_TX_SND_QUEUE	KS2_NETCP_PDMA_TX_SND_QUEUE
140 
141 /* Keystone net */
142 #define CONFIG_DRIVER_TI_KEYSTONE_NET
143 #define CONFIG_KSNET_MAC_ID_BASE		KS2_MAC_ID_BASE_ADDR
144 #define CONFIG_KSNET_NETCP_BASE			KS2_NETCP_BASE
145 #define CONFIG_KSNET_SERDES_SGMII_BASE		KS2_SGMII_SERDES_BASE
146 #define CONFIG_KSNET_SERDES_SGMII2_BASE		KS2_SGMII_SERDES2_BASE
147 #define CONFIG_KSNET_SERDES_LANES_PER_SGMII	KS2_LANES_PER_SGMII_SERDES
148 
149 /* SerDes */
150 #define CONFIG_TI_KEYSTONE_SERDES
151 
152 #define CONFIG_AEMIF_CNTRL_BASE		KS2_AEMIF_CNTRL_BASE
153 
154 /* I2C Configuration */
155 #define CONFIG_SYS_I2C_DAVINCI
156 #define CONFIG_SYS_DAVINCI_I2C_SPEED	100000
157 #define CONFIG_SYS_DAVINCI_I2C_SLAVE	0x10 /* SMBus host address */
158 #define CONFIG_SYS_DAVINCI_I2C_SPEED1	100000
159 #define CONFIG_SYS_DAVINCI_I2C_SLAVE1	0x10 /* SMBus host address */
160 #define CONFIG_SYS_DAVINCI_I2C_SPEED2	100000
161 #define CONFIG_SYS_DAVINCI_I2C_SLAVE2	0x10 /* SMBus host address */
162 
163 /* EEPROM definitions */
164 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
165 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
166 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
167 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
168 #define CONFIG_ENV_EEPROM_IS_ON_I2C
169 
170 /* NAND Configuration */
171 #define CONFIG_NAND_DAVINCI
172 #define CONFIG_KEYSTONE_RBL_NAND
173 #define CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE	CONFIG_ENV_OFFSET
174 #define CONFIG_SYS_NAND_MASK_CLE		0x4000
175 #define CONFIG_SYS_NAND_MASK_ALE		0x2000
176 #define CONFIG_SYS_NAND_CS			2
177 #define CONFIG_SYS_NAND_USE_FLASH_BBT
178 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
179 
180 #define CONFIG_SYS_NAND_LARGEPAGE
181 #define CONFIG_SYS_NAND_BASE_LIST		{ 0x30000000, }
182 #define CONFIG_SYS_MAX_NAND_DEVICE		1
183 #define CONFIG_SYS_NAND_MAX_CHIPS		1
184 #define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
185 #define CONFIG_MTD_PARTITIONS
186 
187 /* USB Configuration */
188 #define CONFIG_USB_XHCI_KEYSTONE
189 #define CONFIG_USB_SS_BASE			KS2_USB_SS_BASE
190 #define CONFIG_USB_HOST_XHCI_BASE		KS2_USB_HOST_XHCI_BASE
191 #define CONFIG_DEV_USB_PHY_BASE			KS2_DEV_USB_PHY_BASE
192 #define CONFIG_USB_PHY_CFG_BASE			KS2_USB_PHY_CFG_BASE
193 
194 /* U-Boot general configuration */
195 #define CONFIG_MISC_INIT_R
196 #define CONFIG_MX_CYCLIC
197 #define CONFIG_TIMESTAMP
198 
199 /* EDMA3 */
200 #define CONFIG_TI_EDMA3
201 
202 #define KERNEL_MTD_PARTS						\
203 	"mtdparts="							\
204 	SPI_MTD_PARTS
205 
206 #define DEFAULT_FW_INITRAMFS_BOOT_ENV					\
207 	"name_fw_rd=k2-fw-initrd.cpio.gz\0"				\
208 	"set_rd_spec=setenv rd_spec ${rdaddr}:${filesize}\0"		\
209 	"init_fw_rd_net=dhcp ${rdaddr} ${tftp_root}/${name_fw_rd}; "	\
210 		"run set_rd_spec\0"					\
211 	"init_fw_rd_nfs=nfs ${rdaddr} ${nfs_root}/boot/${name_fw_rd}; "	\
212 		"run set_rd_spec\0"					\
213 	"init_fw_rd_ramfs=setenv rd_spec -\0"				\
214 	"init_fw_rd_ubi=ubifsload ${rdaddr} ${bootdir}/${name_fw_rd}; "	\
215 		"run set_rd_spec\0"					\
216 
217 #define DEFAULT_PMMC_BOOT_ENV						\
218 	"set_name_pmmc=setenv name_pmmc ti-sci-firmware-${soc_variant}.bin\0" \
219 	"dev_pmmc=0\0"							\
220 	"get_pmmc_net=dhcp ${loadaddr} ${tftp_root}/${name_pmmc}\0"	\
221 	"get_pmmc_nfs=nfs ${loadaddr} ${nfs_root}/boot/${name_pmmc}\0"	\
222 	"get_pmmc_ramfs=run get_pmmc_net\0"				\
223 	"get_pmmc_mmc=load mmc ${bootpart} ${loadaddr} "		\
224 			"${bootdir}/${name_pmmc}\0"			\
225 	"get_pmmc_ubi=ubifsload ${loadaddr} ${bootdir}/${name_pmmc}\0"	\
226 	"run_pmmc=rproc init; rproc list; "				\
227 		"rproc load ${dev_pmmc} ${loadaddr} 0x${filesize}; "	\
228 		"rproc start ${dev_pmmc}\0"				\
229 
230 #define CONFIG_EXTRA_ENV_SETTINGS					\
231 	DEFAULT_LINUX_BOOT_ENV						\
232 	CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS				\
233 	"bootdir=/boot\0" \
234 	"tftp_root=/\0"							\
235 	"nfs_root=/export\0"						\
236 	"mem_lpae=1\0"							\
237 	"addr_ubi=0x82000000\0"						\
238 	"addr_secdb_key=0xc000000\0"					\
239 	"name_kern=zImage\0"						\
240 	"addr_mon=0x87000000\0"						\
241 	"addr_non_sec_mon=0x0c087fc0\0"					\
242 	"addr_load_sec_bm=0x0c08c000\0"					\
243 	"run_mon=mon_install ${addr_mon}\0"				\
244 	"run_mon_hs=mon_install ${addr_non_sec_mon} "			\
245 			"${addr_load_sec_bm}\0"				\
246 	"run_kern=bootz ${loadaddr} ${rd_spec} ${fdtaddr}\0"		\
247 	"init_net=run args_all args_net\0"				\
248 	"init_nfs=setenv autoload no; dhcp; run args_all args_net\0"	\
249 	"init_ubi=run args_all args_ubi; "				\
250 		"ubi part ubifs; ubifsmount ubi:rootfs;\0"			\
251 	"get_fdt_net=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0"	\
252 	"get_fdt_nfs=nfs ${fdtaddr} ${nfs_root}/boot/${name_fdt}\0"	\
253 	"get_fdt_ubi=ubifsload ${fdtaddr} ${bootdir}/${name_fdt}\0"		\
254 	"get_kern_net=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0"	\
255 	"get_kern_nfs=nfs ${loadaddr} ${nfs_root}/boot/${name_kern}\0"	\
256 	"get_kern_ubi=ubifsload ${loadaddr} ${bootdir}/${name_kern}\0"		\
257 	"get_mon_net=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0"	\
258 	"get_mon_nfs=nfs ${addr_mon} ${nfs_root}/boot/${name_mon}\0"	\
259 	"get_mon_ubi=ubifsload ${addr_mon} ${bootdir}/${name_mon}\0"	\
260 	"get_fit_net=dhcp ${fit_loadaddr} ${tftp_root}"			\
261 						"/${fit_bootfile}\0"	\
262 	"get_fit_nfs=nfs ${fit_loadaddr} ${nfs_root}/boot/${fit_bootfile}\0"\
263 	"get_fit_ubi=ubifsload ${fit_loadaddr} ${bootdir}/${fit_bootfile}\0"\
264 	"get_fit_mmc=load mmc ${bootpart} ${fit_loadaddr} "		\
265 					"${bootdir}/${fit_bootfile}\0"	\
266 	"get_uboot_net=dhcp ${loadaddr} ${tftp_root}/${name_uboot}\0"	\
267 	"get_uboot_nfs=nfs ${loadaddr} ${nfs_root}/boot/${name_uboot}\0" \
268 	"burn_uboot_spi=sf probe; sf erase 0 0x100000; "		\
269 		"sf write ${loadaddr} 0 ${filesize}\0"		\
270 	"burn_uboot_nand=nand erase 0 0x100000; "			\
271 		"nand write ${loadaddr} 0 ${filesize}\0"		\
272 	"args_all=setenv bootargs console=ttyS0,115200n8 rootwait=1 "	\
273 		KERNEL_MTD_PARTS					\
274 	"args_net=setenv bootargs ${bootargs} rootfstype=nfs "		\
275 		"root=/dev/nfs rw nfsroot=${serverip}:${nfs_root},"	\
276 		"${nfs_options} ip=dhcp\0"				\
277 	"nfs_options=v3,tcp,rsize=4096,wsize=4096\0"			\
278 	"get_fdt_ramfs=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0"	\
279 	"get_kern_ramfs=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0"	\
280 	"get_mon_ramfs=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0"	\
281 	"get_fit_ramfs=dhcp ${fit_loadaddr} ${tftp_root}"		\
282 						"/${fit_bootfile}\0"	\
283 	"get_fs_ramfs=dhcp ${rdaddr} ${tftp_root}/${name_fs}\0"	\
284 	"get_ubi_net=dhcp ${addr_ubi} ${tftp_root}/${name_ubi}\0"	\
285 	"get_ubi_nfs=nfs ${addr_ubi} ${nfs_root}/boot/${name_ubi}\0"	\
286 	"burn_ubi=nand erase.part ubifs; "				\
287 		"nand write ${addr_ubi} ubifs ${filesize}\0"		\
288 	"init_ramfs=run args_all args_ramfs get_fs_ramfs\0"		\
289 	"args_ramfs=setenv bootargs ${bootargs} "			\
290 		"rdinit=/sbin/init rw root=/dev/ram0 "			\
291 		"initrd=0x808080000,80M\0"				\
292 	"no_post=1\0"							\
293 	"mtdparts=mtdparts=davinci_nand.0:"				\
294 		"1024k(bootloader)ro,512k(params)ro,-(ubifs)\0"
295 
296 #ifndef CONFIG_BOOTCOMMAND
297 #ifndef CONFIG_TI_SECURE_DEVICE
298 #define CONFIG_BOOTCOMMAND						\
299 	"run init_${boot}; "						\
300 	"run get_mon_${boot} run_mon; "					\
301 	"run get_kern_${boot}; "					\
302 	"run init_fw_rd_${boot}; "					\
303 	"run get_fdt_${boot}; "						\
304 	"run run_kern"
305 #else
306 #define CONFIG_BOOTCOMMAND						\
307 	"run run_mon_hs; "						\
308 	"run init_${boot}; "						\
309 	"run get_fit_${boot}; "						\
310 	"bootm ${fit_loadaddr}#${name_fdt}"
311 #endif
312 #endif
313 
314 /* Now for the remaining common defines */
315 #include <configs/ti_armv7_common.h>
316 
317 /* we may include files below only after all above definitions */
318 #include <asm/arch/hardware.h>
319 #include <asm/arch/clock.h>
320 #ifndef CONFIG_SOC_K2G
321 #define CONFIG_SYS_HZ_CLOCK		ks_clk_get_rate(KS2_CLK1_6)
322 #else
323 #define CONFIG_SYS_HZ_CLOCK		get_external_clk(sys_clk)
324 #endif
325 
326 #endif /* __CONFIG_KS2_EVM_H */
327