1 /* 2 * ti_armv7_common.h 3 * 4 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 * 8 * The various ARMv7 SoCs from TI all share a number of IP blocks when 9 * implementing a given feature. Rather than define these in every 10 * board or even SoC common file, we define a common file to be re-used 11 * in all cases. While technically true that some of these details are 12 * configurable at the board design, they are common throughout SoC 13 * reference platforms as well as custom designs and become de facto 14 * standards. 15 */ 16 17 #ifndef __CONFIG_TI_ARMV7_COMMON_H__ 18 #define __CONFIG_TI_ARMV7_COMMON_H__ 19 20 /* 21 * We typically do not contain NOR flash. In the cases where we do, we 22 * undefine this later. 23 */ 24 #define CONFIG_SYS_NO_FLASH 25 26 /* Support both device trees and ATAGs. */ 27 #define CONFIG_CMDLINE_TAG 28 #define CONFIG_SETUP_MEMORY_TAGS 29 #define CONFIG_INITRD_TAG 30 31 /* 32 * Our DDR memory always starts at 0x80000000 and U-Boot shall have 33 * relocated itself to higher in memory by the time this value is used. 34 * However, set this to a 32MB offset to allow for easier Linux kernel 35 * booting as the default is often used as the kernel load address. 36 */ 37 #define CONFIG_SYS_LOAD_ADDR 0x82000000 38 39 /* 40 * We setup defaults based on constraints from the Linux kernel, which should 41 * also be safe elsewhere. We have the default load at 32MB into DDR (for 42 * the kernel), FDT above 128MB (the maximum location for the end of the 43 * kernel), and the ramdisk 512KB above that (allowing for hopefully never 44 * seen large trees). We say all of this must be within the first 256MB 45 * as that will normally be within the kernel lowmem and thus visible via 46 * bootm_size and we only run on platforms with 256MB or more of memory. 47 */ 48 #define DEFAULT_LINUX_BOOT_ENV \ 49 "loadaddr=0x82000000\0" \ 50 "kernel_addr_r=0x82000000\0" \ 51 "fdtaddr=0x88000000\0" \ 52 "fdt_addr_r=0x88000000\0" \ 53 "rdaddr=0x88080000\0" \ 54 "ramdisk_addr_r=0x88080000\0" \ 55 "scriptaddr=0x80000000\0" \ 56 "pxefile_addr_r=0x80100000\0" \ 57 "bootm_size=0x10000000\0" 58 59 #define DEFAULT_MMC_TI_ARGS \ 60 "mmcdev=0\0" \ 61 "mmcrootfstype=ext4 rootwait\0" \ 62 "finduuid=part uuid mmc 0:2 uuid\0" \ 63 "args_mmc=run finduuid;setenv bootargs console=${console} " \ 64 "${optargs} " \ 65 "root=PARTUUID=${uuid} rw " \ 66 "rootfstype=${mmcrootfstype}\0" \ 67 "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 68 "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \ 69 "source ${loadaddr}\0" \ 70 "bootenvfile=uEnv.txt\0" \ 71 "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \ 72 "env import -t ${loadaddr} ${filesize}\0" \ 73 "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenvfile}\0" \ 74 "envboot=mmc dev ${mmcdev}; " \ 75 "if mmc rescan; then " \ 76 "echo SD/MMC found on device ${mmcdev};" \ 77 "if run loadbootscript; then " \ 78 "run bootscript;" \ 79 "else " \ 80 "if run loadbootenv; then " \ 81 "echo Loaded env from ${bootenvfile};" \ 82 "run importbootenv;" \ 83 "fi;" \ 84 "if test -n $uenvcmd; then " \ 85 "echo Running uenvcmd ...;" \ 86 "run uenvcmd;" \ 87 "fi;" \ 88 "fi;" \ 89 "fi;\0" \ 90 91 /* 92 * DDR information. If the CONFIG_NR_DRAM_BANKS is not defined, 93 * we say (for simplicity) that we have 1 bank, always, even when 94 * we have more. We always start at 0x80000000, and we place the 95 * initial stack pointer in our SRAM. Otherwise, we can define 96 * CONFIG_NR_DRAM_BANKS before including this file. 97 */ 98 #ifndef CONFIG_NR_DRAM_BANKS 99 #define CONFIG_NR_DRAM_BANKS 1 100 #endif 101 #define CONFIG_SYS_SDRAM_BASE 0x80000000 102 103 #ifndef CONFIG_SYS_INIT_SP_ADDR 104 #define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ 105 GENERATED_GBL_DATA_SIZE) 106 #endif 107 108 /* Timer information. */ 109 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 110 111 /* I2C IP block */ 112 #define CONFIG_I2C 113 #define CONFIG_CMD_I2C 114 #define CONFIG_SYS_I2C 115 116 /* MMC/SD IP block */ 117 #define CONFIG_MMC 118 #define CONFIG_GENERIC_MMC 119 #define CONFIG_CMD_MMC 120 121 /* McSPI IP block */ 122 #define CONFIG_SPI 123 #define CONFIG_CMD_SPI 124 125 /* GPIO block */ 126 127 /* 128 * The following are general good-enough settings for U-Boot. We set a 129 * large malloc pool as we generally have a lot of DDR, and we opt for 130 * function over binary size in the main portion of U-Boot as this is 131 * generally easily constrained later if needed. We enable the config 132 * options that give us information in the environment about what board 133 * we are on so we do not need to rely on the command prompt. We set a 134 * console baudrate of 115200 and use the default baud rate table. 135 */ 136 #ifdef CONFIG_DFU_MMC 137 #define CONFIG_SYS_MALLOC_LEN ((16 << 20) + CONFIG_SYS_DFU_DATA_BUF_SIZE) 138 #else 139 #define CONFIG_SYS_MALLOC_LEN (16 << 20) 140 #endif 141 #define CONFIG_SYS_HUSH_PARSER 142 #define CONFIG_SYS_CONSOLE_INFO_QUIET 143 #define CONFIG_BAUDRATE 115200 144 #define CONFIG_ENV_VARS_UBOOT_CONFIG /* Strongly encouraged */ 145 #define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */ 146 147 /* As stated above, the following choices are optional. */ 148 #define CONFIG_SYS_LONGHELP 149 #define CONFIG_AUTO_COMPLETE 150 #define CONFIG_CMDLINE_EDITING 151 #define CONFIG_VERSION_VARIABLE 152 153 /* We set the max number of command args high to avoid HUSH bugs. */ 154 #define CONFIG_SYS_MAXARGS 64 155 156 /* Console I/O Buffer Size */ 157 #define CONFIG_SYS_CBSIZE 512 158 /* Print Buffer Size */ 159 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ 160 + sizeof(CONFIG_SYS_PROMPT) + 16) 161 /* Boot Argument Buffer Size */ 162 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 163 164 /* 165 * When we have SPI, NOR or NAND flash we expect to be making use of 166 * mtdparts, both for ease of use in U-Boot and for passing information 167 * on to the Linux kernel. 168 */ 169 #if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI) 170 #define CONFIG_MTD_DEVICE /* Required for mtdparts */ 171 #define CONFIG_CMD_MTDPARTS 172 #endif 173 174 #define CONFIG_CMD_ASKENV 175 #define CONFIG_CMD_BOOTZ 176 #define CONFIG_SUPPORT_RAW_INITRD 177 178 /* 179 * Common filesystems support. When we have removable storage we 180 * enabled a number of useful commands and support. 181 */ 182 #if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) 183 #define CONFIG_DOS_PARTITION 184 #define CONFIG_CMD_FAT 185 #define CONFIG_FAT_WRITE 186 #define CONFIG_CMD_EXT2 187 #define CONFIG_CMD_EXT4 188 #define CONFIG_CMD_FS_GENERIC 189 #define CONFIG_PARTITION_UUIDS 190 #define CONFIG_CMD_PART 191 #endif 192 193 /* 194 * Our platforms make use of SPL to initalize the hardware (primarily 195 * memory) enough for full U-Boot to be loaded. We also support Falcon 196 * Mode so that the Linux kernel can be booted directly from SPL 197 * instead, if desired. We make use of the general SPL framework found 198 * under common/spl/. Given our generally common memory map, we set a 199 * number of related defaults and sizes here. 200 */ 201 #if !defined(CONFIG_NOR_BOOT) && \ 202 !(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX)) 203 #define CONFIG_SPL_FRAMEWORK 204 #define CONFIG_SPL_OS_BOOT 205 206 /* 207 * Place the image at the start of the ROM defined image space (per 208 * CONFIG_SPL_TEXT_BASE and we limit our size to the ROM-defined 209 * downloaded image area. We initalize DRAM as soon as we can so that 210 * we can place stack, malloc and BSS there. We load U-Boot itself into 211 * memory at 0x80800000 for legacy reasons (to not conflict with older 212 * SPLs). We have our BSS be placed 2MiB after this, to allow for the 213 * default Linux kernel address of 0x80008000 to work with most sized 214 * kernels, in the Falcon Mode case. We have the SPL malloc pool at the 215 * end of the BSS area. We suggest that the stack be placed at 32MiB after 216 * the start of DRAM to allow room for all of the above (handled in Kconfig). 217 */ 218 #ifndef CONFIG_SYS_TEXT_BASE 219 #define CONFIG_SYS_TEXT_BASE 0x80800000 220 #endif 221 #ifndef CONFIG_SPL_BSS_START_ADDR 222 #define CONFIG_SPL_BSS_START_ADDR 0x80a00000 223 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ 224 #endif 225 #ifndef CONFIG_SYS_SPL_MALLOC_START 226 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ 227 CONFIG_SPL_BSS_MAX_SIZE) 228 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 229 #endif 230 231 /* RAW SD card / eMMC locations. */ 232 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ 233 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ 234 235 /* FAT sd card locations. */ 236 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 237 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 238 239 #ifdef CONFIG_SPL_OS_BOOT 240 /* FAT */ 241 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 242 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" 243 244 /* RAW SD card / eMMC */ 245 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ 246 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ 247 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ 248 249 /* spl export command */ 250 #define CONFIG_CMD_SPL 251 #endif 252 253 #ifdef CONFIG_MMC 254 #define CONFIG_SPL_LIBDISK_SUPPORT 255 #define CONFIG_SPL_MMC_SUPPORT 256 #define CONFIG_SPL_FAT_SUPPORT 257 #define CONFIG_SPL_EXT_SUPPORT 258 #endif 259 260 #define CONFIG_SYS_THUMB_BUILD 261 262 /* General parts of the framework, required. */ 263 #define CONFIG_SPL_I2C_SUPPORT 264 #define CONFIG_SPL_LIBCOMMON_SUPPORT 265 #define CONFIG_SPL_LIBGENERIC_SUPPORT 266 #define CONFIG_SPL_SERIAL_SUPPORT 267 #define CONFIG_SPL_POWER_SUPPORT 268 #define CONFIG_SPL_GPIO_SUPPORT 269 #define CONFIG_SPL_BOARD_INIT 270 271 #ifdef CONFIG_NAND 272 #define CONFIG_SPL_NAND_SUPPORT 273 #define CONFIG_SPL_NAND_BASE 274 #define CONFIG_SPL_NAND_DRIVERS 275 #define CONFIG_SPL_NAND_ECC 276 #define CONFIG_SPL_MTD_SUPPORT 277 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 278 #endif 279 #endif /* !CONFIG_NOR_BOOT */ 280 281 /* Generic Environment Variables */ 282 283 #ifdef CONFIG_CMD_NET 284 #define NETARGS \ 285 "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \ 286 "::off\0" \ 287 "nfsopts=nolock\0" \ 288 "rootpath=/export/rootfs\0" \ 289 "netloadimage=tftp ${loadaddr} ${bootfile}\0" \ 290 "netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \ 291 "netargs=setenv bootargs console=${console} " \ 292 "${optargs} " \ 293 "root=/dev/nfs " \ 294 "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ 295 "ip=dhcp\0" \ 296 "netboot=echo Booting from network ...; " \ 297 "setenv autoload no; " \ 298 "dhcp; " \ 299 "run netloadimage; " \ 300 "run netloadfdt; " \ 301 "run netargs; " \ 302 "bootz ${loadaddr} - ${fdtaddr}\0" 303 #else 304 #define NETARGS "" 305 #endif 306 307 #include <config_distro_defaults.h> 308 #define CONFIG_CMD_EXT4_WRITE 309 310 #endif /* __CONFIG_TI_ARMV7_COMMON_H__ */ 311