1 /* 2 * ti_armv7_common.h 3 * 4 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 * 8 * The various ARMv7 SoCs from TI all share a number of IP blocks when 9 * implementing a given feature. Rather than define these in every 10 * board or even SoC common file, we define a common file to be re-used 11 * in all cases. While technically true that some of these details are 12 * configurable at the board design, they are common throughout SoC 13 * reference platforms as well as custom designs and become de facto 14 * standards. 15 */ 16 17 #ifndef __CONFIG_TI_ARMV7_COMMON_H__ 18 #define __CONFIG_TI_ARMV7_COMMON_H__ 19 20 /* Common define for many platforms. */ 21 #define CONFIG_OMAP 22 #define CONFIG_OMAP_COMMON 23 24 /* 25 * We typically do not contain NOR flash. In the cases where we do, we 26 * undefine this later. 27 */ 28 #define CONFIG_SYS_NO_FLASH 29 30 /* Support both device trees and ATAGs. */ 31 #define CONFIG_OF_LIBFDT 32 #define CONFIG_CMDLINE_TAG 33 #define CONFIG_SETUP_MEMORY_TAGS 34 #define CONFIG_INITRD_TAG 35 36 /* 37 * Our DDR memory always starts at 0x80000000 and U-Boot shall have 38 * relocated itself to higher in memory by the time this value is used. 39 */ 40 #define CONFIG_SYS_LOAD_ADDR 0x80000000 41 42 /* 43 * Default to a quick boot delay. 44 */ 45 #define CONFIG_BOOTDELAY 1 46 47 /* 48 * DDR information. We say (for simplicity) that we have 1 bank, 49 * always, even when we have more. We always start at 0x80000000, 50 * and we place the initial stack pointer in our SRAM. 51 */ 52 #define CONFIG_NR_DRAM_BANKS 1 53 #define CONFIG_SYS_SDRAM_BASE 0x80000000 54 #define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ 55 GENERATED_GBL_DATA_SIZE) 56 57 /* Timer information. */ 58 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 59 #define CONFIG_SYS_HZ 1000 /* 1ms clock */ 60 61 /* I2C IP block */ 62 #define CONFIG_I2C 63 #define CONFIG_CMD_I2C 64 #define CONFIG_HARD_I2C 65 #define CONFIG_SYS_I2C_SPEED 100000 66 #define CONFIG_SYS_I2C_SLAVE 1 67 #define CONFIG_I2C_MULTI_BUS 68 #define CONFIG_DRIVER_OMAP24XX_I2C 69 70 /* MMC/SD IP block */ 71 #define CONFIG_MMC 72 #define CONFIG_GENERIC_MMC 73 #define CONFIG_OMAP_HSMMC 74 #define CONFIG_CMD_MMC 75 76 /* McSPI IP block */ 77 #define CONFIG_SPI 78 #define CONFIG_OMAP3_SPI 79 #define CONFIG_CMD_SPI 80 81 /* GPIO block */ 82 #define CONFIG_OMAP_GPIO 83 #define CONFIG_CMD_GPIO 84 85 /* 86 * GPMC NAND block. We support 1 device and the physical address to 87 * access CS0 at is 0x8000000. 88 */ 89 #ifdef CONFIG_NAND 90 #define CONFIG_CMD_NAND 91 #define CONFIG_NAND_OMAP_GPMC 92 #define CONFIG_SYS_NAND_BASE 0x8000000 93 #define CONFIG_SYS_MAX_NAND_DEVICE 1 94 #endif 95 96 /* 97 * The following are general good-enough settings for U-Boot. We set a 98 * large malloc pool as we generally have a lot of DDR, and we opt for 99 * function over binary size in the main portion of U-Boot as this is 100 * generally easily constrained later if needed. We enable the config 101 * options that give us information in the environment about what board 102 * we are on so we do not need to rely on the command prompt. We set a 103 * console baudrate of 115200 and use the default baud rate table. 104 */ 105 #define CONFIG_SYS_MALLOC_LEN (1024 << 10) 106 #define CONFIG_SYS_LONGHELP 107 #define CONFIG_SYS_HUSH_PARSER 108 #define CONFIG_AUTO_COMPLETE 109 #define CONFIG_CMDLINE_EDITING 110 #define CONFIG_SYS_PROMPT "U-Boot# " 111 #define CONFIG_VERSION_VARIABLE 112 #define CONFIG_ENV_VARS_UBOOT_CONFIG 113 #define CONFIG_BAUDRATE 115200 114 115 /* We set the max number of command args high to avoid HUSH bugs. */ 116 #define CONFIG_SYS_MAXARGS 64 117 118 /* Console I/O Buffer Size */ 119 #define CONFIG_SYS_CBSIZE 512 120 /* Print Buffer Size */ 121 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ 122 + sizeof(CONFIG_SYS_PROMPT) + 16) 123 /* Boot Argument Buffer Size */ 124 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 125 126 #define CONFIG_ENV_OVERWRITE 127 #define CONFIG_SYS_CONSOLE_INFO_QUIET 128 129 /* 130 * When we have SPI, NOR or NAND flash we expect to be making use of 131 * mtdparts, both for ease of use in U-Boot and for passing information 132 * on to the Linux kernel. 133 */ 134 #if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) 135 #define CONFIG_MTD_DEVICE /* Required for mtdparts */ 136 #define CONFIG_CMD_MTDPARTS 137 #endif 138 139 /* 140 * For commands to use, we take the default list and add a few other 141 * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH 142 * prior to this include, in order to skip a few commands. When we do 143 * have flash, if we expect these commands they must be enabled in that 144 * config. 145 */ 146 #include <config_cmd_default.h> 147 #define CONFIG_CMD_ASKENV 148 #define CONFIG_CMD_ECHO 149 #define CONFIG_CMD_BOOTZ 150 151 /* 152 * Common filesystems support. When we have removable storage we 153 * enabled a number of useful commands and support. 154 */ 155 #if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) 156 #define CONFIG_DOS_PARTITION 157 #define CONFIG_CMD_FAT 158 #define CONFIG_FAT_WRITE 159 #define CONFIG_CMD_EXT2 160 #define CONFIG_CMD_EXT4 161 #define CONFIG_CMD_FS_GENERIC 162 #endif 163 164 /* 165 * Our platforms make use of SPL to initalize the hardware (primarily 166 * memory) enough for full U-Boot to be loaded. We also support Falcon 167 * Mode so that the Linux kernel can be booted directly from SPL 168 * instead, if desired. We make use of the general SPL framework found 169 * under common/spl/. Given our generally common memory map, we set a 170 * number of related defaults and sizes here. 171 */ 172 #ifndef CONFIG_NOR_BOOT 173 #define CONFIG_SPL 174 #define CONFIG_SPL_FRAMEWORK 175 #define CONFIG_SPL_OS_BOOT 176 177 /* 178 * Place the image at the start of the ROM defined image space. 179 * We limit our size to the ROM-defined downloaded image area, and use the 180 * rest of the space for stack. We load U-Boot itself into memory at 181 * 0x80800000 for legacy reasons (to not conflict with older SPLs). We 182 * have our BSS be placed 1MiB after this, to allow for the default 183 * Linux kernel address of 0x80008000 to work, in the Falcon Mode case. 184 * We have the SPL malloc pool at the end of the BSS area. 185 */ 186 #define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR 187 #define CONFIG_SYS_TEXT_BASE 0x80800000 188 #define CONFIG_SPL_BSS_START_ADDR 0x80a00000 189 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ 190 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ 191 CONFIG_SPL_BSS_MAX_SIZE) 192 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 193 194 /* RAW SD card / eMMC locations. */ 195 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ 196 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ 197 198 /* FAT sd card locations. */ 199 #define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 200 #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" 201 202 #ifdef CONFIG_SPL_OS_BOOT 203 #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) 204 205 /* FAT */ 206 #define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage" 207 #define CONFIG_SPL_FAT_LOAD_ARGS_NAME "args" 208 209 /* RAW SD card / eMMC */ 210 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ 211 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ 212 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ 213 214 /* NAND */ 215 #ifdef CONFIG_NAND 216 #define CONFIG_CMD_SPL_NAND_OFS 0x240000 /* end of u-boot */ 217 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000 218 #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000 219 #endif 220 221 /* spl export command */ 222 #define CONFIG_CMD_SPL 223 #endif 224 225 #ifdef CONFIG_MMC 226 #define CONFIG_SPL_MMC_SUPPORT 227 #define CONFIG_SPL_FAT_SUPPORT 228 #endif 229 230 /* General parts of the framework. */ 231 #define CONFIG_SPL_I2C_SUPPORT 232 #define CONFIG_SPL_LIBCOMMON_SUPPORT 233 #define CONFIG_SPL_LIBDISK_SUPPORT 234 #define CONFIG_SPL_LIBGENERIC_SUPPORT 235 #define CONFIG_SPL_SERIAL_SUPPORT 236 #define CONFIG_SPL_GPIO_SUPPORT 237 #define CONFIG_SPL_BOARD_INIT 238 239 #ifdef CONFIG_NAND 240 #define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */ 241 #define CONFIG_SPL_NAND_SUPPORT 242 #define CONFIG_SPL_NAND_BASE 243 #define CONFIG_SPL_NAND_DRIVERS 244 #define CONFIG_SPL_NAND_ECC 245 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 246 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 247 #endif 248 #endif /* !CONFIG_NOR_BOOT */ 249 250 #endif /* __CONFIG_TI_ARMV7_COMMON_H__ */ 251